A study of the stability of pyrolytic carbon-coated Fe/SiO2 composites in HNO3 and the effect of pyrolysis temperatures on their magnetic properties

Fe/SiO₂ composites prepared by a sol-gel combined hydrogen reduction method were coated with carbon by the pyrolysis of acetylene. Scanning electron microscopy (SEM) showed that the as-prepared sample consists of only carbon-coated Fe/SiO₂ particles without the presence of one-dimensional carbon or any other unwanted carbon formation. The stability of the Fe/SiO₂ composites under a HNO₃ solution at room temperature was greatly enhanced after they were coated with carbon. The effect of pyrolysis temperatures was also studied.     

Electrodeposition and characteristics of Ni80Fe20/Cu composite wires

Electrodeposited Ni₈₀Fe₂₀/Cu composite wire has significant advantages over amorphous wire as sensing element for weak magnetic field sensors, such as orthogonal fluxgate sensors, due to its non-ferromagnetic and conductive core structure. In this study, the key processing parameters are investigated, including electrodeposition current density, duty cycle, electrolyte solution, pH value, applied magnetic field, effect of seeded layers, and post annealing.     

The effect of B2O3 addition to the microstructure and magnetic properties of Ni0.4Zn0.6Fe2O4 ferrite

The effects of 0.01 and 0.1 mol B₂O₃ addition to the microstructure and magnetic properties of a Ni–Zn ferrite composition expressed by a molecular formula of Ni_0.4Zn_0.6Fe₂O₄ were investigated. The toroid-shaped samples prepared by pressing the milled raw materials used in the preparation of the composition were sintered in the range of 1000–1300 °C. The addition of 0.01 mol B₂O₃ increased the grain growth and densification giving rise to reduced intergranular and intragranular porosity due to liquid-phase sintering. The sintered toroid sample at 1300 °C gave the optimum magnetic properties of B_r=170 mT, H_c=0.025 kA/m and a high initial permeability value of μ_i=4000. The increment of the B₂O₃ content to 0.1 mol resulted in a pronounced grain growth and also gave rise to large porosity due to the evaporation of B₂O₃ at higher sintering temperatures. Hence, it resulted in an air-gap effect in the hysteresis curves of these samples.     

Eu and Fe Mössbauer study of mechanically alloyed EuFeO3

EuFeO₃ was prepared by mechanical alloying starting from europium and iron oxides. After 20 h of milling the resulting compound is pure EuFeO₃. Samples were studied as a function of milling period using XRD, Mössbauer, SEM, and magnetic measurements. Mössbauer spectroscopy was used to probe both the transition metal and the rare-earth sites. Results are compared with previous works on EuFeO₃ prepared by different methods.     

Enhancement of giant magneto-impedance effect in Ni80Fe20/SiO2/Cu composite wires

Ni₈₀Fe₂₀/SiO₂/Cu composite wires of Cu core 60 μm in diameter and coated with layers of SiO₂ and Ni₈₀Fe₂₀ were prepared by RF magnetron sputtering. The influences of the insulator layer thickness, the measurement mode and the magnitude of the driving current on the giant magneto-impedance (GMI) effect were investigated. The results showed that there was an optimum thickness of the insulator layer and the driving current can influence the shape of the MI curve. Resonance enhancement of the GMI was found in the new measurement mode. The results are discussed by taking account of the electromagnetic interactions.     

Al65Cu20Co15十边形准晶体

X射线衍射证明正常凝固Al₆₅Cu₂₀Co₁₅合金主要由10边形二维准晶体组成。扫描电子显微镜在断口上观察到平截头10棱锥柱体的完整外形,反映了其10/m或10/mmm点群对称性。组成外形的各平面与10边形相D面电子衍射图上强衍射斑对应。 关键词：     

Structural and magnetic properties of SmCo5.6Ti0.4 alloy

Three series of SmCo_5.6Ti_0.4 samples were prepared by quenching, melt spinning, and ball milling, respectively. Annealing at different temperatures was carried out for the three series. The influence of the processing routes on the structural and magnetic properties was systematically investigated for this alloy. The as-quenched bulk sample consisted of three phases with a rather coarse grain microstructure. Low intrinsic coercivity (_iH_c) of 0.12 T was obtained in this sample. While the as-spun ribbons and as-milled/annealed powders showed the CaCu₅-type phase (1:5) plus Th₂Zn₁₇-type phase (2:17), and the 1:5 phase plus TbCu₇-type phase (1:7), respectively, with nanograin microstructure. The _iH_c of as-spun ribbons and as-milled/annealed (700 °C for 2 h) powders was found to be 0.59 and 2.23 T, respectively. Coercivity mechanism of these as-spun ribbons is mainly of nucleation type. In the as-milled/annealed powders, the network of the nanograin boundaries is believed to provide strong pinning sites for the domain wall movement.     

Optical and magnetic properties of (Ga1−xMnx)N/GaN digital ferromagnetic heterostructures

(Ga_1−xMn_x)N/GaN digital ferromagnetic heterostructures (DFHs) and (Ga_1−xMn_x)N/GaN grown on GaN buffer layers by using molecular beam epitaxy have been investigated. The photoluminescence (PL) spectra showed band-edge exciton transitions. They also showed peaks corresponding to the neutral donor-bound exciton and the exciton transitions between the conduction band and the Mn acceptor, indicative of the Mn atoms acting as substitution. The magnetization curves as functions of the magnetic field at 5 K indicated that the saturation magnetic moment in the (Ga_1−xMn_x)N/GaN DFHs decreased with increasing Mn mole fraction and that the saturation magnetic moment and the coercive field in the (Ga_1−xMn_x)N/GaN DFHs were much larger than those in (Ga_1−xMn_x)N thin films. These results indicate that the (Ga_1−xMn_x)N/GaN DFHs hold promise for potential applications in spintronic devices.     

Structure and magnetic properties of nanocrystalline Fe75Si25 powders prepared by mechanical alloying

Nanocrystalline Fe₇₅Si₂₅ powders were prepared by mechanical alloying in a planetary ball mill. The evolution of the microstructure and magnetic properties during the milling process were studied by X-ray diffraction, scanning electron microscope and vibrating sample magnetometer measurements. The evolution of non-equilibrium solid solution Fe (Si) during milling was accompanied by refinement of crystallite size down to 10 nm and the introduction of high density of dislocations of the order of 10¹⁷ m⁻². During the milling process, Fe sites get substituted by Si. This structural change and the resulting disorder are reflected in the lattice parameters and average magnetic moment of the powders milled for various time periods. A progressive increase of coercivity was also observed with increasing milling time. The increase of coercivity could be attributed to the introduction of dislocations and reduction of powder particle size as a function of milling time.     

Magnetic study of Mg0.95Mn0.05Fe2O4 ferrite nanoparticles

The magnetic properties of Mg_0.95Mn_0.05Fe₂O₄ ferrite samples with an average particle size of ∼6.0±0.6 nm have been studied using X-ray diffraction, Mössbauer spectroscopy, dc magnetization and frequency dependent real χ^′(T) and imaginary χ^″(T) parts of ac susceptibility measurements. A magnetic transition to an ordered state is observed at about 195 K from Mössbauer measurements. The zero-field-cooled (ZFC) and field-cooled (FC) magnetization have been recorded at low field and show the typical behavior of a small particle system. The ZFC curve displays a broad maximum at , a temperature which depends upon the distribution of particle volumes in the sample. The FC curve was nearly flat below , as compared with monotonically increasing characteristics of non-interacting superparamagnetic systems indicating the existence of strong interactions among the nanoparticles. A frequency-dependent peak observed in χ^′(T) is well described by Vogel-Fulcher law, yielding a relaxation time and an interaction parameter . Such values show the strong interactions and rule out the possibility of spin-glass (SG) features among the nanoparticle system. On the other hand fitting with the Néel-Brown model and the power law yields an unphysical large value of τ₀ (∼6×10⁻⁶⁹ and 1.2×10⁻²² s respectively).     

Microstructure characterization and magnetic behavior of NiAlxFe2−xO4 and Ni1−yMnyAl0.2Fe1.8O4 ferrites

NiAl_xFe_2−xO₄ and Ni_1−yMn_yAl_0.2Fe_1.8O₄ ferrites were prepared by the conventional ceramic method and were characterized by X-ray diffraction, scanning electron microscopy, and magnetic measurements. The single spinel phase was confirmed for all prepared samples. A proper explanation of data is possible if the Al³⁺ ions are assumed to replace Fe³⁺ ions in the A and B sites simultaneously for NiAl_xFe_2−xO₄ ferrites, and if the Mn²⁺ ions are assumed to replace Ni²⁺ ions in the B sites for Ni_1−yMn_yAl_0.2Fe_1.8O₄ ferrites. Microstructural factors play an important role in the magnetic behavior of Ni_1−yMn_yAl_0.2Fe_1.8O₄ ferrites with large Mn²⁺ content.     

Microstructure and magnetic properties of nanocomposite FePt/MgO and FePt/Ag films

An in-plane magnetic anisotropy of FePt film is obtained in the MgO 5 nm/FePt t nm/MgO 5 nm films (where t=5, 10 and 20 nm). Both the in-plane coercivity (H_c∥) and the perpendicular magnetic anisotropy of FePt films are increased when introducing an Ag-capped layer instead of MgO-capped layer. An in-plane coercivity is 3154 Oe for the MgO 5 nm/FePt 10 nm/MgO 5 nm film, and it can be increased to 4846 Oe as a 5 nm Ag-capped layer instead of MgO-capped layer. The transmission electron microscopy (TEM)-energy disperse spectrum (EDS) analysis shows that the Ag mainly distributed at the grain boundary of FePt, that leads the increase of the grain boundary energy, which will enhance coercivity and perpendicular magnetic anisotropy of FePt film.     

Magnetic and structural study of Cu-doped TiO2 thin films

Transparent pure and Cu-doped (2.5, 5 and 10 at.%) anatase TiO₂ thin films were grown by pulsed laser deposition technique on LaAlO₃ substrates. The samples were structurally characterized by X-ray absorption spectroscopy and X-ray diffraction. The magnetic properties were measured using a SQUID. All films have a FM-like behaviour. In the case of the Cu-doped samples, the magnetic cycles are almost independent of the Cu concentration. Cu atoms are forming CuO and/or substituting Ti in TiO₂. The thermal treatment in air promotes the CuO segregation. Since CuO is antiferromagnetic, the magnetic signals present in the films could be assigned to Cu substitutionally replacing cations in TiO₂.     

A study of the effect of ZrO2 on the magnetic properties of FePt/ZrO2 multilayer

Fe_xPt_100−x(30 nm) and [Fe_xPt_100−x(3 nm)/ZrO₂]₁₀ (x = 37, 48, 57, 63, 69) films with different ZrO₂ content were prepared by RF magnetron sputtering technique, then were annealed at 550 °C for 30 min. This work investigates the effect of ZrO₂ doping on the microstructural evolution, magnetic properties, grain size, as well as the ordering kinetics of FePt alloy films. The as-deposited films behaved a disordered state, and the ordered L1₀ structure was obtained by post-annealing. The magnetic properties of the films are changed from soft magnetism to hard magnetism after annealing. The variation of the largest coercivities of [Fe_xPt_100−x/ZrO₂]₁₀ films with the Fe atomic percentage, x and differing amounts of ZrO₂ content reveals that as we increase the ZrO₂ content we must correspondingly increase the amount of Fe. This phenomenon suggests that the Zr or O atoms of ZrO₂ preferentially react with the Fe atoms of FePt alloy to form compounds. In addition, introducing the nonmagnetic ZrO₂ can reduce the intergrain exchange interactions of the FePt/ZrO₂ films, and the interactions are decreased as the ZrO₂ content increases, the dipole interactions are observed in FePt/ZrO₂ films as the ZrO₂ content is more than 15%.     

Effect of SnO2 coating on the magnetic properties of nanocrystalline CuFe2O4

Nanocrystalline CuFe₂O₄ and CuFe₂O₄/xSnO₂ nanocomposites (x=0, 1, 5 wt%) have been successfully synthesized by one-pot reaction of urea-nitrate combustion method. The transmission electron microscope study reveals that the particle size of the as synthesized CuFe₂O₄ and CuFe₂O₄/5 wt%SnO₂ are 10 and 20 nm, respectively. The SnO₂ coating on the nanocrystalline CuFe₂O₄ was confirmed from HRTEM studies. The resultant products were sintered at 1100 °C and characterized by XRD and SQUID for compound formation and magnetic studies, respectively. The X-ray diffraction pattern shows the well-defined sharp peak that confirms the phase pure compound formation of tetragonal CuFe₂O₄. The zero field cooled (ZFC) and field cooled (FC) magnetization was performed using SQUID magnetometer from 2 to 350 K and the magnetic hysteresis measurement was carried out to study the magnetic properties of nanocomposites.     

Synthesis and magnetic properties of spinel CoFe2O4 nanowire arrays

Spinel CoFe₂O₄ nanowire arrays were synthesized in nanopores of anodic aluminum oxide (AAO) template using aqueous solution of cobalt and iron nitrates as precursor. The precursor was filled into the nanopores by vacuum impregnation. After heat treatment, it transformed to spinel CoFe₂O₄ nanowires. The structure, morphology and magnetic properties of the sample were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). The results indicate that the nanowire arrays are compact. And the individual nanowires have a high aspect ratio, which are about 80 nm in diameter and 10 μm in length. The nanowires are polycrystalline spinel phase. Magnetic measurements indicate that the nanowire arrays are nearly magnetic isotropic. The reason is briefly discussed. Moreover, the temperature dependence of the coercive force of the nanowire arrays was studied.     

Growth temperature dependence of the hysteretic behavior of Ni0.5Zn0.5Fe2O4 thin films

Herein, a discussion of the effect of deposition temperature on the magnetic behavior of Ni_0.5Zn_0.5Fe₂O₄ thin films. The thin films were grown by r.f. sputtering technique on (1 0 0) MgO single-crystal substrates at deposition temperatures ranging between 400 and 800 °C. The grain boundary microstructure was analyzed via atomic force microscopy (AFM). AFM images show that grain size (φ∼70-112 nm) increases with increasing deposition temperature, according to a diffusion growth model. From magneto-optical Kerr effect (MOKE) measurements at room temperature, coercive fields, H_c, between 37and 131 Oe were measured. The coercive field, H_c, as a function of grain size, reaches a maximum value of 131 Oe for φ ∼93 nm, while the relative saturation magnetization exhibits a minimum value at this grain size. The behaviors observed were interpreted as the existence of a critical size for the transition from single- to multi-domain regime. The saturation magnetization (21 emu/g<M_s<60 emu/g) was employed to quantify the critical magnetic intergranular correlation length (L_c≈166 nm), where a single-grain to coupled-grain behavior transition occurs. Experimental hysteresis loops were fitted by the Jiles-Atherton model (JAM). The value of the k-parameter of the JAM fitted by means of this model (k/μ_o∼50 A m²) was correlated to the domain size from the behavior of k, we observed a maximum in the density of defects for the sample with φ∼93 nm.     

Li0.5Fe2.5−xMnxO4 ferrite sintered from microwave-induced combustion

Li_0.5Fe_2.5−xMn_xO₄ (0≦x≦1.0) powders with small and uniformly sized particles were successfully synthesized by microwave-induced combustion, using lithium nitrate, ferric nitrate, manganese nitrate and carbohydrazide as the starting materials. The process takes only a few minutes to obtain as-received Mn-substituted lithium ferrite powders. The resultant powders annealed at 650 ^°C for 2 h and were investigated by thermogravimeter/differential thermal analyzer (TG/DTA), X-ray diffractometer (XRD), transmission electron microscopy (TEM), vibrating sample magnetometer (VSM), and thermomagnetic analysis (TMA). The results revealed that the Mn content were strongly influenced the magnetic properties and Curie temperature of Mn-substituted lithium ferrite powder. As for sintered Li_0.5Fe_2.5−xMn_xO₄ specimens, substituting an appropriate amount of Mn for Fe in the Li_0.5Fe_2.5−xMn_xO₄ specimens markedly improved the complex permeability and loss tangent.     

The role of the dopant in the magnetism of Fe-doped SnO2 films

Transparent pure and Fe-doped SnO₂ thin films were grown by pulsed laser deposition technique on LaAlO₃ substrates. X-ray diffraction shows that the films are polycrystalline and have the rutile structure. Surprisingly, the pure film presents magnetic-like behavior at room temperature with a saturated magnetization of almost one-third of the doped film (∼3.6 and 11.3 emu/g, respectively) and its magnetization could not be attributed to any impurity phase. Taking into account the magnetic moment measured in the pure film, the effective contribution of the impurity in the doped one can be inferred to be ∼2 μ_B per Fe atom. A large magnetic moment was also predicted by an ab initio calculation in the doped system, which increases if an oxygen vacancy is present near the Fe impurity.