Microwave dielectric and magnetic properties of superparamagnetic 8-nm Fe3O4 nanoparticles

The superparamagnetic 8-nm Fe₃O₄ nanoparticles were successfully prepared by chemical oxidation process. For the complex permittivity, the dual dielectric relaxation processes have been proved by two overlapped Cole–Cole semicircles, and the natural resonance frequency is 3.03 GHz for the complex permeability. The maximum reflection loss value reaches −55.5 dB at 6.11 GHz with 3.85 mm in the thickness of the absorbers for the superparamagnetic 8-nm Fe₃O₄ nanoparticles which is better than that of 150 nm and 30 nm Fe₃O₄ nanoparticles. It is believed that the superparamagnetic 8-nm Fe₃O₄ nanoparticles can be used as a kind of candidate for microwave absorber.     

Frequency-domain birefringence measurement of biological binding to magnetic nanoparticles

Optical detection of the frequency-dependent magnetic relaxation signal is used to monitor the binding of biological molecules to magnetic nanoparticles in a ferrofluid. Biological binding reactions cause changes in the magnetic relaxation signal due to an increase in the average hydrodynamic diameter of the nanoparticles. To allow the relaxation signal to be detected in dilute ferrofluids, measurements are made using a balanced photodetector, resulting in a 25 μV/√Hz noise floor, within 50% of the theoretical limit imposed by photon shot noise. Measurements of a ferrofluid composed of magnetite nanoparticles coated with anti-IgG antibodies show that the average hydrodynamic diameter increases from 115.2 to 125.4 nm after reaction with IgG.     

On the possibility of using short chain length mono-carboxylic acids for stabilization of magnetic fluids

Short chain length mono-carboxylic acids (lauric and myristic acids) are used to coat magnetite nanoparticles in non-polar organic liquids, which results in highly stable magnetic fluids. The new fluids are compared with classical organic fluids stabilized by oleic acid (OA). Magnetic granulometry and small-angle neutron scattering (polarized mode) reveal a great difference in the particle size distribution function for the studied magnetic fluids, particularly a decrease in the characteristic particle radius of magnetite when lauric and myristic acids are used instead of OA.     

An improved technique for the measurement of the complex susceptibility of magnetic colloids in the microwave region

Measurements by means of the short-circuit (S/C) and open circuit (O/C) transmission line techniques are well established methods for investigating the magnetic and dielectric properties of magnetic colloids, respectively. In particular, the S/C technique has been used in the investigation of the resonant properties of ferrofluids; resonance being indicated by the transition of the real component of the magnetic complex susceptibility, χ(ω)=χ′(ω)−iχ″(ω), from a positive to a negative value at a frequency, f_res. However, under certain circumstances, the accuracy of the S/C technique is affected by the dielectric properties of the sample, hence incurring errors in the measurement of χ(ω) and indeed of f_res. Here we present a model which, by combining short-circuit and open circuit measurements, is developed in a manner in which the permeability, μ, and the permittivity, ε, contribute simultaneously to the calculation of χ(ω), thereby providing superior experimental results in comparison to those obtained by the S/C technique alone. For the two ferrofluid samples measured it is demonstrated that the dielectric properties affect the high frequency content of the susceptibility spectrum.     

Scaling laws and approximate expressions for the dynamic magnetic susceptibility of Brownian nanoparticles

We present simplified expressions for the out-of-phase component of the dynamic susceptibility χ″ of lognormal-sized magnetic nanoparticles under Brownian rotation. These expressions are based on transforming the general integral functions used for χ″ in the convolution of gaussian functions. χ″ can thus be expressed as a sum of gaussians with parameters directly related to those of the size distribution and to the saturation magnetization. The gaussian fit of χ″(ω) (where ω is the ac field frequency) is a simpler way to determine these structural and magnetic parameters as it avoids fitting χ″(ω) to an integral function. The expressions derived for χ″ suggest that χ″T data collapses in a ωη(T)/T scale (where T is the temperature and η the fluids viscosity), which is confirmed by numerical calculations. We also discuss the limits of validity of these approximations in real systems where both Néel and Brownian relaxation mechanisms coexist and we present further approximations for the relation of ω_χ with the average volume (being ω_χ the frequency at which χ″ is maximum). The ωη(T)/T scale can be used to qualitatively evaluate the dominance of the Brownian relaxation mechanism.     

Low-frequency complex magnetic susceptibility of magnetic composite microspheres in colloidal dispersion

A procedure is presented to determine the permanent magnetic dipole moment of composite microspheres containing magnetic nanoparticles with a blocked magnetic dipole moment. The composite particles are dispersed in a solvent, and the complex magnetic susceptibility is measured from 0.1 to 1000 Hz using a highly sensitive new setup. Composite particles with a permanent magnetic dipole moment are revealed by a characteristic frequency that corresponds to the Brownian rotation of the microspheres. From measured susceptibility spectra, we calculate the permanent magnetic dipole moment of recently developed cobalt ferrite-doped silica and latex microspheres.     

Fabrication and characterization of thermo-sensitive magnetic polymer composite nanoparticles

Novel dual-functional nanospheres composed of Fe₃O₄ nanoparticles embedded in a thermo-sensitive polymer were synthesized by emulsifier-free emulsion polymerization. The Fe₃O₄ nanoparticles were prepared by chemical precipitation. The surface of these particles was modified by oleic acid to achieve stability against agglomeration. These stable particles were then polymerized using N-isopropylacrylamide as the main monomer, divinylbenzene as the crosslinker and potassium persulfate as the initiator. The nanospheres were characterized by Fourier-transform infrared spectrum, transmission electron microscopy, thermogravimetric analysis, vibrating sample magnetometer and dynamic light scattering. The results show that the lower critical solution temperature of thermo-sensitive magnetic immunomicrospheres was between 40 and 45 °C.     

Influence of dextran coating on the magnetic behaviour of iron oxide nanoparticles

Magnetic iron oxide nanoparticles with mean diameters in the range from 10 to 30 nm were prepared by modified chemical precipitation routes. The particles were suspended in an aqueous solution by coating of the particles with carboxymethyldextran. A stability against agglomeration was achieved over a period of more than 7 days. In the present investigation, the structural and the magnetic properties of the nanoparticles were investigated. The influence of the dextran shell on the strength of the dipole–dipole interactions between the neighbouring particles was determined by investigation of the remanence behaviour (Henkel plot) of coated as well as of uncoated particles.     

Experimental investigation of dipolar interaction in suspensions of magnetic nanoparticles

The structure and the magnetisation behaviour of two different systems of magnetic nanoparticles (MNP), namely Resovist^® with a wide core size distribution (diameter, σ=0.3) and SHP-20 with a rather narrow distribution (σ=0.1), were investigated by magnetorelaxometry (MRX) and magnetisation measurements in a wide concentration range. MRX on fluid and solid suspensions yielded the distribution of hydrodynamic diameters and effective magnetic anisotropy energies (E_A), where towards higher iron concentrations the spatial particle correlation, i.e. aggregation, and also the width of the E_A distribution were increased significantly. It was further found that these effects quantitatively depend on the suspension medium, where an increased salt concentration enhanced the aggregate size distribution and E_A dispersion. At mentioned higher MNP concentrations, the quasistatic magnetisation, normalised with respect to the iron content, decreased by up to 40%. In the case of SHP-20, where single core MNPs dominate, the maximum of this drop down of the magnetisation occurred at a field strength that corresponds to the strength of mean squared dipolar interaction.     

Study of molecular surface coating on the stability of maghemite nanoparticles

In this study γ-Fe₂O₃ nanoparticle, surface-coated with increasing amount of oleic acid, have been prepared while the stability against particle degradation under laser excitation intensity was investigated. Maghemite nanoparticle was obtained via oxidation of magnetite nanoparticle, the latter synthesized by co-precipitation of Fe (II) and Fe (III) ions in alkaline medium. By varying the experimental conditions of surface-coating maghemite nanoparticles with oleic acid, samples with different grafting coefficient were obtained and investigated using X-ray diffraction and different spectroscopic techniques, namely Raman, Mössbauer, and infrared. The amount of oleic acid adsorbed on the maghemite surface was estimated via the carbon content obtained from elemental analysis.     

Synthesis and magnetic properties of Mn–Zn ferrite nanoparticles

Mn–Zn ferrite nanoparticles (Mn_1−xZn_xFe₂O₄) are synthesized by a hydrothermal precipitation approach using metal sulfate solution and aqueous ammonia. The analysis methods of XRPD, TEM, TGA, and VSM are used to characterize the magnetic nanoparticles. Through the characterization of the precipitated nanoparticles, the effects of the reacting component proportions and preparation techniques on the Curie temperature, the magnetization, and the size distribution of Mn–Zn ferrite nanoparticles are discussed. Furthermore, the Mn–Zn ferrite nanoparticles are used to prepare ferrofluid. Variation of the magnetic properties of the ferrite nanoparticles with the composition content x of Zn and the magnetic moment of the nanoparticles are discussed.     

Study of local magnetic fields and magnetic ordering in fluid and solid matrices containing magnetite nanoparticles using TEMPOL stable radical

The stable nitroxide radical 2,2,6,6-tetramethyl-4-hydroxy-piperidin-1-oxyl (TEMPOL) has been applied as a sensor to study magnetite nanoparticles both in water suspension and in dried gelatin films. g-values and line widths of ESR spectra of the probe were found to be sensitive to the local magnetic fields of magnetic nanoparticles. Calculated on the basis of the sensor ESR spectra, local magnetic fields are stipulated by linear aggregates of magnetite nanoparticles formed in applied outer magnetic fields and are significantly lower than local magnetic fields estimated from the static magnetic measurements data.     

Preparation and magnetic properties of magnetite nanoparticles by sol–gel method

 Magnetite (Fe₃O₄) nanoparticles have been successfully synthesized by sol–gel method combined with annealing under vacuum. The phase structures, morphologies, particle sizes, chemical composition, and magnetic properties of Fe₃O₄ nanoparticles have been characterized by X-ray diffraction, field emission scanning electron microscopy, energy-dispersive X-ray spectrometer and vibrating sample magnetometer (VSM). The results indicate that the size, the corresponding saturation magnetization value and coercivity value of Fe₃O₄ nanoparticles increase with the increase of synthesized temperature. And the phase transformation of Fe₃O₄ nanoparticles has been studied under different atmospheres and temperatures.     

Gaussian approximation in the theory of MR signal formation in the presence of structure-specific magnetic field inhomogeneities

A detailed theoretical analysis of the free induction decay (FID) and spin echo (SE) MR signal formation in the presence of mesoscopic structure-specific magnetic field inhomogeneities is developed in the framework of the Gaussian phase distribution approximation. The theory takes into account diffusion of nuclear spins in inhomogeneous magnetic fields created by arbitrarily shaped magnetized objects with permeable boundaries. In the short-time limit the FID signal decays quadratically with time and depends on the objects' geometry only through the volume fraction, whereas the SE signal decays as 5/2 power of time with the coefficient depending on both the volume fraction of the magnetized objects and their surface-to-volume ratio. In the motional narrowing regime, the FID and SE signals for objects of finite size decay mono-exponentially; a simple general expression is obtained for the relaxation rate constant deltaR2. In the case of infinitely long cylinders in the motional narrowing regime the theory predicts non-exponential signal decay lnS approximately -tlnt in accordance with previous results. For specific geometries of the objects (spheres and infinitely long cylinders) exact analytical expressions for the FID and SE signals are given. The theory can be applied, for instance, to biological systems where mesoscopic magnetic field inhomogeneities are induced by deoxygenated red blood cells, capillary network, contrast agents, etc.     

Investigation of surface passivation process on magnetic nanoparticles by Raman spectroscopy

A detailed study of the surface passivation process in superparamagnetic cobalt ferrite nanoparticles has been carried out using micro Raman spectroscopy. In addition to Raman spectroscopy, X-ray diffraction and atomic absorption spectroscopy were also used to investigate passivated and non-passivated samples. The data were discussed in terms of changes in the structural characteristics of the samples considering the introduction of Fe ions during the passivation. We found an improvement of the nanoparticle crystallinity due to the passivation process.     

Polarization and transmission of microwaves in the magnetic suspension in the applied magnetic field

The production method of magnetic suspension consisting of ferromagnetic particles dispersed in cedarwood oil is presented at the beginning of this article. Next, the set-up for microwaves generation using a klystron is described. The main part of this paper concerning microwave transmission and polarization during its passage in samples of the produced magnetic suspension placed in a magnetic field is based on the following parameters: induction of this field, filling factor of magnetic suspension by ferromagnetic particles, dimensions of particles, viscosity of liquid carrier, and ratio of the magnetic field changes. Conducted investigations show that microwaves are damped and polarized in these magnetic suspensions. Obtained results are discussed and observed effects are explained by ordering of ferromagnetic particles in magnetic suspension by applied magnetic field.     

Determination of the anisotropy constant and saturation magnetization of magnetic nanoparticles from magnetization relaxation curves

We have developed a new method for the determination of the anisotropy constant and saturation magnetization of magnetic nanoparticles. This method deals with the approximation of magnetization relaxation curves measured upon application and further fast switching off the dc magnetizing field. The relaxation process is registered in the time interval from 6 μs to several minutes by using a scanning high-T _C SQUID-microscope equipped with a specially designed electronic circuit composed of a fast solid-state switch and a low-inductance magnetizing coil. The algorithm for calculating the approximation data is based on the activation Néel–Arrhenius law and takes into account the size distribution of the nanoparticles and the angular distribution of their easy axes. The performance of the method is demonstrated on dilute (∼0.2 vol%) ensembles of near-spherical Fe₃O₄ nanoparticles with a mean size of 7.7 nm and a standard deviation of 45% as determined from transmission electron microscopy data.     

Sonochemical immobilization of noble metal nanoparticles on the surface of maghemite: mechanism and morphological control of the products

Aqueous sample solutions containing noble metal ions (HAuCl₄, Na₂PdCl₄, H₂PtCl₆), polyethyleneglycol monostearate, and magnetic maghemite nanoparticles were irradiated with high power ultrasound. Analyses of the products showed that noble metal ions were reduced by the effects of ultrasound, and the formed noble metal nanoparticles were uniformly immobilized on the surface of the maghemite. The present “one pot process” significantly simplifies the immobilization of noble metal nanoparticles on the surface of supports, compared with the conventional impregnation method. The average diameter of immobilized Au was 7–13 nm, and the diameters of Pd and Pt were several nm. The diameters depended upon the concentration of polyethyleneglycol monostearate and the concentration of noble metal ions, but not upon the maghemite concentration, indicating the possibility of the morphological controls of the products by adjusting these preparation conditions. The measurements of the average diameters and the numbers of immobilized Au nanoparticles obtained under various conditions suggest that the nucleation of Au does not occur on the surface of maghemite, but it might occur in the homogeneous bulk solution.     

The influence of long range interparticle correlations on the magnetically induced optical anisotropy in magnetic colloids

In this paper we develop a theoretical model for the magnetically induced optical anisotropy in dense magnetic colloids made of spherical and un-aggregated magnetic monodomain nanoparticles. Both dipole-field and dipole-dipole magnetic and electric interactions between the magnetic monodomain particles are taken into account in the Hamiltonian of the system. Using the pair correlation function in a colloidal suspension of magnetic nanoparticles developed by Ivanov and Kuznetsova (2001) [11], the complex dielectric constant of a magnetic colloid is modeled as a function of the light polarization direction, the magnetic field intensity and magnetic particle concentration and diameter. The two main features of the model are that, on the one hand, it predicts the possibility of magnetically induced optical anisotropy in dense magnetic colloids made of spherical and un-aggregated monodomain nanoparticles, and on the other hand, unlike the existing models for diluted samples, it predicts a non-linear dependence of dichroism and birefringence on magnetic particle concentration.     

On the magnetostatics of chains of magnetic nanoparticles

A novel approach is presented for the computation of the magnetostatic energy of straight and bent chains of identical, uniformly magnetized particles of arbitrary shape. The formalism relies on the concept of the magnetometric tensor field, and allows for closed form expressions for the magnetostatic energy, demagnetization factor, Young's modulus, and bending modulus of chains in terms of the shape amplitude of the particles. Analytical solutions are presented for straight chains of spheres, cubes, and cylinders, and for bent chains of spheres. Numerical results include chains of octahedra, tetrahedra, cuboctahedra, and bi-cones. The axial demagnetization factor for the bi-cone shape is derived in analytical form. An approximate energy expression, using the full shape-dependent interaction formalism for short separation distances, and the standard dipolar interaction expression for larger distances, is introduced.