Permeability-frequency spectra of (Fe1−xcox)73.5Cu1Nb3Si13.5B9 nanocrystalline alloys under different magnetic fields

Under various amplitude of AC magnetic fields domain wall motion is the main mechanism in the magnetization process. This includes domain wall bulging and domain wall displacing. In this paper complex permeability-frequency spectra of (Fe_1−xCo_x)_73.5Cu₁Nb₃Si_13.5B₉ (x=0,0.5$x=0,0.5$) nanocrystalline alloys were measured as a function of the AC magnetic field, ranging from 0.001 to 0.04 Oe. Obvious changes have been found in complex permeability spectra for alloy x=0$x=0$ with the change of the amplitude of AC magnetic field, but variation of AC magnetic field has little effect on complex permeability spectra for alloy x=0.5$x=0.5$. This is attributed to the increased pinning field after substitution of Fe with Co in Fe_73.5Cu₁Nb₃Si_13.5B₉ nanaocrystalline alloy.     

Soft magnetic properties and giant magneto-impedance effect of Fe73.5−xCrxSi13.5B9Nb3Au1 (x=1–5) alloys

In this paper, the effect of microstructural and surface morphological developments on the soft magnetic properties and giant magneto-impedance (GMI) effect of Fe_73.5−xCr_xSi_13.5B₉Nb₃Au₁ (x=1, 2, 3, 4, 5) alloys was investigated. It was found that the Cr addition causes slight decrease in the mean grain size of α-Fe(Si) grains. AFM results indicated a large variation of surface morphology of density and size of protrusions along the ribbon plane due to structural changes caused by thermal treatments with increasing Cr content. Ultrasoft magnetic properties such as the increase of magnetic permeability and the decrease of coercivity were observed in the samples annealed at 540 °C for 30 min. Accordingly, the GMI effect was also observed in the annealed samples.     

Structural and magnetic properties of Co1−xZnxFe2O4 nanoparticles by co-precipitation method

Co_1−xZn_xFe₂O₄ nanoparticles were prepared by co-precipitation method with x varying from 0 to 1.0. The powder samples were characterized by X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and Fourier transform infrared spectroscopy (FTIR). The average crystallite sizes of the particles were determined from XRD. X-ray analysis showed that the samples were cubic spinel. The average crystallite size (D_aveXR) of the particles precipitated was found to vary from 6.92 to 12.02 nm decreasing with the increase in zinc substitution. The lattice constant (a_o) increased with the increase in zinc substitution. The specific saturation magnetization (M_S) of the particles was measured at room temperature. The magnetic parameters such as M_S, H_c, and M_r were found to decrease with the increase in zinc substitution. FTIR spectra of the Co_1−xZn_xFe₂O₄ with x varying from 0 to 1.0 in the range 400–4000 cm⁻¹ were reported. The spinel structure and the crystalline water adsorption of Co_1−xZn_xFe₂O₄ nanoparticles were studied by using FTIR.     

Fabrication and magnetic properties of CoxPd1−x composite nanowire

A series of Co_xPd_1−x   (x=0.37–0.85$x=0.37–0.85$) nanowire arrays have been successfully deposited in a single Co²⁺/ Pd²⁺=20:1 solution by applying the various depositing potentials. We found that the nanowires are the composites of CoPd alloy with some Co and Pd clusters, but the overall structure of the composite wires followed the binary phase relation of Pd–Co. The existence of Pd content makes the nanowires structured in FCC phase, except for Co_0.85Pd_0.15 sample in which some HCP Co phase coexists with the dominating FCC phase. Between Co-rich and Pd-rich nanowires, we found that the optimized composition for Co_xPd_1−x nanowire is around Co_0.73Pd_0.27 in which the coercivity (H_c) and squareness (M_r/M_s) have their maximum values consistently.     

Structure and magnetic properties of (Nd,Dy)16(Fe,Co)76−xTixB8 powders prepared by mechanical alloying

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at % of Ti results in an increase of coercivity from 796 to 1115 kA m⁻¹. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA m⁻¹. Mössbauer investigations shows that for x?1 the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x>1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity decreases due to the presence of an amorphous phase. A heat treatment at a higher temperature (1073 K) for longer time (1 h) results in the full recrystallisation of powders. The mean hyperfine field of the Nd₂Fe₁₄B phase decreases for titanium contents of 0?x?1, and remains constant for x>1. This indicates that the Ti content in the Nd₂Fe₁₄B phase reaches its maximum value.     

Effect of boron concentration on the magnetic properties of (FeCoNi) 100−xBx (x=15 and 20 wt%) nanowire arrays

The Fe_14.5Co_16.5Ni₅₅B₁₅ and the Fe₁₃Co_15.5Ni_51.5B₂₀ ferromagnetic nanowires were deposited using the electrochemical deposition method. The structure of these nanowires was investigated using X-ray diffraction. Squid magnetometer was used to investigate the magnetic behavior. The hysteresis loops of 50 μm long nanowire arrays were studied as a function of boron concentration, nanowire diameter and field orientation. The competition between shape anisotropy and magnetostatic interactions played a vital role in determining the magnetic field necessary to saturate an array. The decrease in coercive field (H_c) and the squareness (SQ) of the hysteresis loop from 100 to 200 nm wire diameter for both types of compositions suggests the formation of multidomains in the nanowire.     

The structure and magnetic properties of Zn1−xNixFe2O4 ferrite nanoparticles prepared by sol–gel auto-combustion

Zn_1−xNi_xFe₂O₄ ferrite nanoparticles were prepared by sol–gel auto-combustion and then annealed at 700 °C for 4 h. The results of differential thermal analysis indicate that the thermal decomposition temperature is about 210 °C and Ni–Zn ferrite nanoparticles could be synthesized in the self-propagating combustion process. The microstructure and magnetic properties were investigated by means of X-ray diffraction, scanning electron microscope, and Vibrating sample magnetometer. It is observed that all the spherical nanoparticles with an average grain size of about 35 nm are of pure spinel cubic structure. The crystal lattice constant declines gradually with increasing x from 0.8435 nm (x=0.20) to 0.8352 nm (x=1.00). Different from the composition of Zn_0.5Ni_0.5Fe₂O₄ for the bulk, the maximum M_s is found in the composition of Zn_0.3Ni_0.7Fe₂O₄ for nanoparticles. The H_c of samples is much larger than the bulk ferrites and increases with the enlarging x. The results of Zn_0.3Ni_0.7Fe₂O₄ annealed at different temperatures indicate that the maximum M_s (83.2 emu/g) appears in the sample annealed at 900 °C. The H_c of Zn_0.3Ni_0.7Fe₂O₄ firstly increases slightly as the grain size increases, and presents a maximum value of 115 Oe when the grains grow up to about 30 nm, and then declines rapidly with the grains further growing. The critical diameter (under the critical diameter, the grain is of single domain) of Zn_0.3Ni_0.7Fe₂O₄ nanoparticles is found to be about 30 nm.     

Magnetic properties of nanocrystalline Co1−xZnxFe2O4 prepared by forced hydrolysis method

Nanocrystalline zinc-substituted cobalt ferrite powders, Co_1−xZn_xFe₂O₄ (x=0, 0.2, 0.4), were for the first time prepared by forced hydrolysis method. Magnetic and structural properties in these specimens were investigated. The average crystallite size is about 3.0 nm. When the zinc substitution increases from x=0 to x=0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g and the coercive field decreases from 1.22 to 0.71 T. All samples are superparamagnetic at room temperature and ferrimagnetic at temperatures below the blocking temperature. The high value of the saturation magnetization and the very thin thickness of the disorder surface layer of all samples suggests that this forced hydrolysis method is suitable not only for preparing two metal element systems but also for three or more ones.     

Large vertical loop shifts in mechanically synthesized (Mn,Fe)2O3−t nanograins

Magnetic properties of zero field cooled (ZFC) and field cooled (FC) sample of (Mn,Fe)₂O_3−t nanograins have been investigated by magnetometry (up to 70 kOe) and Mössbauer spectroscopy (up to 60 kOe) in the temperature interval 4.2–300 K. Large horizontal (up to 0.8 kOe) and vertical (up to 80%) shifts of the magnetization hysteresis loops are observed in the FC regime. The obtained results are discussed in terms of exchange interaction between an antiferromagnetic core and a spin-glass-like state of the nanograins boundaries. It is shown that hysteresis loop shifts (horizontal and vertical) depend on the field cooling magnitude, an effect that can be understood by the change of the boundary magnetic structure induced by the external magnetic field. The vertical magnetization shift is described by a phenomenological model, which takes into account the magnetic interaction between the spin-glass like boundary spins and the applied field.     

Structure and magnetic properties of nanocrystalline Fe75Si25 powders prepared by mechanical alloying

Nanocrystalline Fe₇₅Si₂₅ powders were prepared by mechanical alloying in a planetary ball mill. The evolution of the microstructure and magnetic properties during the milling process were studied by X-ray diffraction, scanning electron microscope and vibrating sample magnetometer measurements. The evolution of non-equilibrium solid solution Fe (Si) during milling was accompanied by refinement of crystallite size down to 10 nm and the introduction of high density of dislocations of the order of 10¹⁷ m⁻². During the milling process, Fe sites get substituted by Si. This structural change and the resulting disorder are reflected in the lattice parameters and average magnetic moment of the powders milled for various time periods. A progressive increase of coercivity was also observed with increasing milling time. The increase of coercivity could be attributed to the introduction of dislocations and reduction of powder particle size as a function of milling time.     

Depth dependence of Néel wall pinning on amorphous CoxSi1−x films with diluted arrays of elliptical antidots

Diluted arrays of elliptical antidots have been fabricated by optical lithography, electron beam lithography and plasma etching on amorphous Co₇₄Si₂₆ magnetic films with a well-defined uniaxial anisotropy. The magnetic behavior of two identical antidot arrays but with different hole depth in comparison with film thickness has been studied by transverse magneto-optical Kerr effect. Significant differences appear in the coercivity depending on whether the magnetic film is completely perforated or not, indicating a much more effective domain wall pinning process when the depth of the holes is smaller than the magnetic film thickness.     

Electronic structure of cubic ErxGa1−xN using the LSDA+U approach

Electronic structure calculations were performed for substitutional erbium rare-earth impurity in cubic GaN using density-functional theory calculations within the LSDA+U approach (local spin-density approximation with Hubbard-U corrections). The LSDA+U method is applied to the rare-earth 4f states. The Er_xGa_1−xN is found to be a semiconductor, where the filled f-states are located in the valence bands and the empty ones above the conduction band edge. The filled and empty f-states are also shown to shift downwards and upwards in the valence and conduction bands, respectively, with increase in the U potentials.     

Ferromagnetism in MnxGe1−x films prepared by magnetron sputtering

Mn_xGe_1−x thin films were prepared by magnetron sputtering with a substrate temperature of 673 K and subsequently annealed at 873 K. The X-ray diffraction (XRD) measurements showed that all samples had a single Ge cubic structure. No films showed clear magnetic domain structure under a magnetic force microscope (MFM). Atom force microscope (AFM) measurements showed that the films had an uniform particle size distribution, and a columnar growth pattern. X-ray photoelectron spectroscopy (XPS) measurements indicated that the valences of both Mn and Ge atoms increase with the Mn concentration. The resistance decreased with increasing temperature, suggesting that the films were typical semiconductors. Magnetic measurements carried out using a Physical Property Measurement System (PPMS) showed that all samples exhibited ferromagnetism at room temperature. There was a small concentration of Mn₁₁Ge₈ in the films, but the ferromagnetism was mainly induced by Mn substitution for Ge site.     

Microstructures and coercivities of SmCox and Sm(Co,Cu)5 films prepared by magnetron sputtering

We have investigated the influence of composition and annealing conditions on the magnetic properties and microstructural features of SmCo_x films that were prepared by sputtering and subsequent annealing. A huge in-plane coercivity of 5.6 T was obtained from an optimally annealed Sm–Co film, which was attributed to the nanometer sized polycrystalline microstructure of the highly anisotropic SmCo₅ phase. Although a high density of planar defects were observed in the films that were annealed at high temperatures, they did not act as strong pinning sites for domain wall motion. The effect of Cu on [SmCo_4.5(9 nm)/Cu(xnm)]₁₀ multilayer thin films was also studied. An appropriate Cu content increased the coercivity.     

The size and space arrangement roles on coercivity of electrodeposited Co1−xCux nanowires

Magnetization curves with various magnetic field orientations and nanowire diameters were measured at room temperature. The measured coercivity as a function of angle (θ) between the field and wire axis reveals that the coercivity decreases with increasing value of θ for various nanowires. Theoretically, based on Monte Carlo simulation we investigated the magnetization reversal modes of the Co_1−xCu_x nanowires and obtained also the θ dependence of the coercivity. Comparing the simulated with the experimental results, we find that the magnetocrystalline anisotropy plays an important role on the magnetic properties of Co_1−xCu_x nanowires, and the magnetization reversal process in the Co_1−xCu_x nanowires could not be understood by the classical uniform rotation mode in the chain-of-sphere model.     

Formation of room-temperature ferromagnetic Zn1−xCoxO nanocrystals

Optical and magnetic properties of Co²⁺-doped ZnO nanocrystals were studied. Optical measurements confirm the incorporation of Co²⁺ in ZnO lattice with tetrahedral geometry. Optical absorption spectra also reveal the partial bleaching of the excitonic feature attributable to an increase in electron concentration. Magnetization measurements indicate the ferromagnetic ordering in Co²⁺-doped ZnO nanocrystals with saturation magnetization . No structural changes were observed in lightly doped ZnO nanocrystals. The present investigations are important in obtaining the ferromagnetic Zn_1−xCo_xO nanocrystals.     

The effect of structure on magnetic properties of Co nanowire arrays

Co nanowire arrays with three typical diameters of 20, 50 and 120 nm have been fabricated into anodic alumina oxide templates using an ac electrodeposition method. It is found that the crystal texture of the Co nanowires depends on the pH value of the deposition electrolyte. X-ray diffraction results show that the (1 0 0) texture appears at pH 6.2, while the diffraction peaks of (1 0 0) and (1 0 1) appear at pH 6.4 with the diameter of 20 nm. In addition, the (0 0 2), (1 0 0) and (1 0 1) peaks appear with an increase of pH value for the nanowire arrays with diameters of 50 and 120 nm, respectively. Magnetic measurements indicate the effect of structure on the magnetic properties of the nanowire arrays, which depend strongly on the different diffraction peaks, as adjusted by the pH value.     

Structural and magnetic properties of SmCo7−xMox alloys

Phase structure and magnetic properties of the as-cast and as-milled/annealed SmCo_7−xMo_x (x=0, 0.1, 0.2, 0.3, 0.4) alloys have been systematically studied. It is found that all the as-cast series alloys are composed of the CaCu₅-type and Th₂Zn₁₇-type phases. Saturation magnetization of the samples decreases with the Mo content increasing. Intrinsic coercivities (_iH_c) of no more than 0.06 T are observed in these as-cast samples, due to their rather coarse grain microstructures with an average grain size of 50 μm. The as-milled/annealed SmCo_7−xMo_x powders crystallize in the disordered TbCu₇-type (1:7) structure with very fine nanograins, and a minor Co₃Mo phase appears in the samples with x=0.1-0.4. High _iH_c (?0.95 T) are achieved in these samples, with a maximum of 1.26 T located at x=0.2, which can be primarily attributed to strong pinning of the domain wall motion at the nanograin boundaries. The temperature coefficient (β) of the _iH_c is about −0.22%/°C in the temperature range of 25-400 °C for the as-milled/annealed samples.     

Spectral dependence of the optical absorption temperature coefficient of CdS1−xSex nanocrystallites embedded in a silicate glass

The absorption temperature coefficient of CdS_1−xSe_x nanocrystallites embedded in a silicate glass has been studied in the temperature range above room temperature at different technological regimes and sizes of nanocrystals. To understand the optical properties of silicate glasses with semiconductor nanocrystallites, especially that at the initial stage of their formation, it is necessary to include the structural changes occurring in the nanocrystals during the heat treatment.     

Transmission electron microscopy of Co2(Cr1−xFex)Al sputtered films and their magnetic tunneling junctions

The microstructures of Co₂FeAl and Co₂(Cr_0.4Fe_0.6)Al sputtered films and of their magnetic tunnel junctions (MTJs) have been investigated to discuss the possible reasons for an unexpectedly low tunneling magnetoresistance (TMR). The structure of the Co₂FeAl film changed from B2 to L2₁ with increasing substrate temperature, while that of the Co₂(Cr_0.4Fe_0.6)Al film remained B2 up to 500 °C. The thermodynamically predicted phase separation was not observed in the films. The low TMR values obtained from the MTJs using the Co₂FeAl and Co₂(Cr_0.4Fe_0.6)Al films are attributed to the low-spin polarization expected from the low degree of order in these films. The TMR values depend sensitively on the interfacial structure of the tunnel junctions when the degree of order of the film is low.