The physics of magnetoelectric composites

This paper gives an overview about the basic ideas of magnetoelectric materials. Up to now single-phase materials show the magnetoelectric effect only below room temperature. Mixing a magnetostrictive with a piezoelectric component is a way to overcome this limitation. This delivers a composite which can exhibit a magnetoelectric effect even at room temperature and higher. Possible candidates for these composites (piezoelectric as well as magnetostrictive) are shown, examples from literature and own results are given. The most important coupling mechanism (magnetization, magnetostriction, local stress, charge) between the magnetostrictive and the piezoelectric phase are discussed. Hints for a direct coupling between the electric polarization and the magnetization are also presented. Different measurement methods for determining the magnetoelectric coefficient are discussed. Representative results as obtained on a technical useful composite between 50% Co-Ferrite+50% BaTiO₃ are given. The behavior of a simple “mixed” structure with that of a “core-shell” structure is compared. The later gives a 20-times larger magnetoelectric coefficient.     

基于能量转换原理的磁电层合材料低频磁电响应分析

提出了一种基于能量转换原理的磁致伸缩/压电层合材料低频磁电响应模型,并对不同层合结构的磁电响应特性进行了对比研究.该模型假定层合材料层间能量传递通过层间剪切力来实现,利用应力函数法分析了磁致伸缩层和压电层的应力与应变,求出了磁致伸缩层的应变能和存储磁场能以及压电层的应变能和电场能;利用Hamilton最小能量原理求出了层间剪切力的大小,获得了开路状态下层合材料的低频磁电响应模型.发现磁电电压系数与磁致伸缩材料的磁导率、泊松比、磁机耦合系数以及压电材料的泊松比、机电耦合系数等有关,并对这些参数的影响进行了分析.同时对两层和三层结构的层合材料磁电特性进行了对比研究,发现层合结构不同则获得的磁电系数公式不同,用相应的公式计算得到的误差才会最小.研究结果表明,本文的理论误差小于6.5%,与其他方法相比,本文的理论模型能更好地描述磁电层合材料的低频磁电响应特性.     

A theory of the inverse magnetoelectric effect in layered magnetostrictive–piezoelectric structures

A theory of the inverse magnetoelectric effect in layered structures has been presented. The theory is based on solving the equations of elastodynamics and electrostatics separately for the magnetostrictive and piezoelectric phases, taking into account the conditions at the interface between the phases. Expressions for the coefficient of inverse magnetoelectric conversion through the parameters characterizing the magnetostrictive and piezoelectric phases have been obtained. Theoretical dependences of the inverse magnetoelectric conversion coefficient on the frequency of the alternating-current electric field for the three-layer PZT–Ni–PZT structure and the two-layer terfenol-D–PZT structure have been calculated. The results of the calculations are in good agreement with the experimental data.     

Disorder-induced enhancement of conductance in doped nanowires

A new mechanism is proposed to explain the enhancement of conductance in doped nanowires.It is shown that the anomalous enhancement of conductance is due to surface doping.The conductance in doped nanowires increases with dopant concentration,which is qualitatively consistent with the existing experimental results.In addition,the I-V curves are linear and thus suggest that the metal electrodes make ohmic contacts to the shell-doped nanowires.The electric current increases with wire diameter (D) and decreases exponentially with wire length (L).Therefore,the doped nanowires have potential application in nanoscale electronic and optoelectronic devices.     

Nanoembossing and piezoelectricity of ferroelectric Pb(Zr0.3,Ti0.7)O3 nanowire arrays

Arrays of ferroelectric PZT nanowires with lateral size down to 200 nm were fabricated by nanoembossing technology. Structural characterization of the embossed PZT film was studied by Raman spectroscopy. Multidomain configurations of a single nanowire have been explored by vertical mode piezoresponse force microscopy (VPFM). The local electric polarization of the individual ferroelectric nanowire has also been investigated. Excellent ferroelectric and piezoelectric characteristics observed in the embossed PZT nanowires suggest nanoembossing technique proposed in this work is promising to become a useful method for ferroelectric nanowires fabrication.     

铁电/铁磁1-3型结构复合材料磁电性能分析

磁致伸缩和压电复合材料通过机械力作用可获得较大的磁电效应，由Terfenol-D粉末与树脂黏接剂构成压磁相，和压电陶瓷PZT黏结在一起，形成1-3型柱状阵列结构，可获得很大的磁电转换系数.采用有限元方法，对此结构的复合材料进行静态分析.复合材料的介电常数和磁电系数的计算结果和实验数值一致，得到样品中应力、应变和电极化分布情况及其关系，并给出进一步提高磁电转换系数的途径，该种复合方式有望成为一种新型高性能的磁电结构. 关键词： 复合材料 磁电效应 有限元     

Design of a low-frequency miniaturized piezoelectric antenna based on acoustically actuated principle

An acoustically actuated piezoelectric antenna is proposed for low frequency (LF) band in this paper. The proposed antenna is theoretically calculated, numerically optimized by the finite element method (FEM), and experimentally analyzed. The measurement results show that the near-field radiation pattern of the piezoelectric antenna is similar to that of the electric dipole antenna. The radiation efficiency of the piezoelectric antenna is 3－4 orders of magnitude higher than that of electrically small antenna (ESA), with their sizes being the same size, and the maximum transmission distance obtained experimentally is 100 cm, which can be improved by increasing the input power. In addition, the gain, directivity, and quality factor of piezoelectric antenna are also analyzed. In this paper, traditional antenna parameters are creatively used to analyze the performance of piezoelectric antenna. The research conclusions can provide reliable theoretical basis for realizing LF antenna miniaturization.     

A Simple Method for Measuring Tensile Force with Piezoelectric Patch

We propose a simple method for monitoring the axial tensile and compressive force in a structure by using a piezoelectric patch with the piezoelectric impedance based measurement. A simple approximate equation for estimating the tensile force in two different conditions, which can be calculated easily if the naturM frequencies in two different states are measuredt is explained in detail. On another front, the natural frequency can be very easily measured by a piezoelectric element by bonding it on the measuring subject structure, because its electric impedance of piezoelement is related to the structural mechanical impedance. Furthermore, an experiment for measuring a tensile force in a simple supported beam is carried out for validating the proposed method. The results show a good accuracy in estimating the tensile force variation by the natural frequency change measured from the piezoelement.     

A slow wave with the structure of an electromagnetic wave in piezoelectric and magnetostrictive media

The propagation of elastic waves in piezoelectric and magnetostrictive materials is considered theoretically. It is shown that an elastic wave in a piezoelectric can create not only a longitudinal electric field parallel to the wave normal (longitudinal piezoactivity) but also a transverse field of electric induction (transverse piezoactivity). The presence of a transverse induction field leads to the appearance of a magnetic field perpendicular to the direction of the wave normal and to the induction vector; therefore, the transverse-piezoactive wave is accompanied by a transverse wave having the structure of an electromagnetic wave and propagating with the speed of sound. Transverse-magnetostrictive elastic waves in magnetostrictive dielectrics are accompanied by a similar wave.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 10, pp. 32–36, October, 1976.     

性能可调的纵向振动圆锥形超声变幅杆*

提出了一种基于压电效应的性能可调纵向振动圆锥形超声变幅杆,并对其振动性能进行了研究。该变幅杆由传统的圆锥形超声变幅杆和压电陶瓷材料组合而成。论文研究了圆锥变幅杆中压电陶瓷材料的厚度、位置以及电阻抗的改变对变幅杆性能参数的影响,并进行了数值模拟仿真及实验验证。结果表明,通过改变压电陶瓷材料的厚度、位置和电阻抗值,可以实现变幅杆共振频率和位移放大系数的改变。理论计算结果与数值模拟值和实验测试值符合得很好。     

Formation of stable nanowires from ferromagnetic metals using 2-butyne-1,4-diol

We mechanically fabricated Fe, Co, and Ni nanowires showing conductance quantization under electrochemical potential control. The effects of 2-butyne-1,4-diol and saccharin on the stability of the nanowires were investigated by measuring the conductance and the stretched length of the nanowires. Nanowires of these ferromagnetic metals were stabilized by adding 2-butyne-1,4-diol. In Co, a monoatomic contact was stretched 0.4 nm in length, indicating the formation of a highly stable monoatomic contact of ferromagnetic metals. The improved stability of the nanowires could originate from specific adsorption of organic molecules on the contacts. Mechanical properties of these metals were considered to explain the origin of the metal-dependent stability of the nanowires.     

基于单神经元PID控制器的压电陶瓷控制方法

卫星地面综合测试是卫星研制过程中的重要环节,对系统功能验证及性能评估具有重要作用。传统的卫星地面综合测试系统存在研制周期长、投入较大、自动化流程不够完整、可重用性较差等不足。而北斗导航卫星地面综合测试系统采用分布式、高实时性、可配置、多主机的集成体系结构,是集计算机通讯、实时控制、实时数据处理、事后分析等功能于一体的测试系统,适用于从卫星总装集成到发射各个阶段的电气测试。通过卫星系统级的各项接口、功能、性能指标测试,表明该系统满足支持系统论证、状态确认、问题排查等测试需求,有力支撑了北斗导航卫星的成功发射和在轨运行。     

Study of polarization control model for piezoelectric actuator

A major deficiency of piezoelectric actuator is that their control accuracy is seriously limited by hysteresis. In this paper, the reason why hysteresis can be reduced by controlling polarization is explained according to the analysis of microscopic polarization mechanism and domain wall theory of piezoelectric actuator. The reason of occurring hysteresis in voltage control mode is also given. Then a control model based polarization is derived. In order to evaluate its effectiveness, the control method based on polarization is realized by controlling the charge of piezoelectric actuator. The experimental results show that the polarization control method is significantly more linear and less hysteresis than the voltage control method.     

Dynamic modeling of thickness-mode piezoelectric transducer using the block diagram approach

This paper aims to provide an alternative method to determine the characteristics of a piezoelectric transducer from measurement. A block diagram approach is proposed to analyze the dynamic characteristics of a thickness-mode piezoelectric transducer at its resonance frequency. Based on the feedback loop framework, the input-output relations of the electromechanical interaction of the transducer are described in terms of linear block diagram models. Furthermore, the closed-loop relations from external force to vibration velocity and electric current from generated voltage are easily found by Mason’s rule to characterize the equivalent mechanical admittance and electrical impedance, respectively. An example of a Langevin transducer with 28.15 kHz resonance frequency is illustrated for dynamics analysis. The frequency responses of the piezoelectric transducer, resulting from a force and current input, are respectively measured to identify the system parameters of the feedback model. The experimental results demonstrate the effectiveness of the proposed method.     

Design of an ultrasonic sensor for measuring distance and detecting obstacles

This paper introduces a novel method for designing the transducer of a highly directional ultrasonic range sensor for detecting obstacles in mobile robot applications. The transducer consists of wave generation, amplification, and radiation sections, and a countermass. The operating principle of this design is based on the parametric array method where the frequency difference between two ultrasonic waves is used to generate a highly directional low-frequency wave with a small aperture. The aim of this study was to design an optimal transducer to generate the two simultaneous longitudinal modes efficiently. We first derived an appropriate mathematical model by combining the continuum model of a bar and countermass with the compatibility condition between a piezoelectric actuator and a linear horn. Then we determined the optimal length of the aluminum horn and the piezoelectric actuator using a finite element method. The proposed sensor exhibited a half-power bandwidth of less than ±1.3° at 44.8 kHz, a much higher directivity than existing conventional ultrasonic range sensors.     

Electric conductance of metal nanowires at mechanically controllable break junctions under electrochemical potential control

We have developed the mechanically controllable break junction setup with an electrochemical cell (EC-MCBJ) to measure the electric conductance of metal nanowires under electrochemical potential control. The electric conductance of Au nanowires was investigated in 0.1 M Na₂SO₄ solution using EC-MCBJ. The conductance of the Au nanowires was quantized in units of G₀ (=2e²/h), showing clear features in the conductance histogram. The atomic contact with a specific conductance value was kept for >5 s, indicating the relatively high stability of the present EC-MCBJ system.     

对称磁电层合板磁电转换效应理论研究

磁致伸缩和压电层合材料通过磁致伸缩和压电效应的乘积可以获得大的磁电效应.通过材料的力学本构方程，建立了对称磁电层合板磁电耦合的静态力学模型；采用ANSYS 80多物理场有限元分析软件，对层合结构的磁电转化效应进行了数值计算，并与理论计算值进行了对比.研究结果表明：磁致伸缩/压电的厚度比增加使磁电电压系数增大；所推导的磁电电压系数公式的计算值与等效电路模型推导的公式计算值符合很好；有限元数值计算结果介于两种模型的计算结果之间. 关键词： 磁电效应 层合板 本构方程 有限元分析     

Development of a miniature STM holder for study of electronic conductance of metal nanowires in UHV-TEM

A new miniature scanning tunneling microscope (STM) holder was developed in order to simultaneously investigate electronic conductance and structure of nanowires in an ultra high-vacuum electron microscope (UHV-TEM). A thin gold wire held between the STM tip and substrate stage of the specimen holder was stretched to form a suspended gold nanowire. The new TEM-STM system allowed us to measure electronic conductance at intervals of 20 ms, and to record high-resolution TEM images on videotape at 30 fps. Suspended gold nanowires formed from [1 1 0] oriented electrodes were well-elongated. In contrast, [1 0 0] and [1 1 1] electrodes produced nanowires with short necks. Electronic conductance was found to change as nanowire structure changed, with conductance quantization in units of 2e²/h, where e is the electron charge and h is Planck’s constant, only being exhibited for well-elongated nanowires.     

Vibration analysis of piezoelectric nanowires with surface and small scale effects

An analytical model for predicting surface effects on the free transverse vibrations of piezoelectric nanowires (NWs) is developed based on the non-local Euler-Bernoulli beam theory. The governing equation of motion for the piezoelectric NW with consideration of both surface and non-local effects is initially obtained, and the exact expressions for the natural frequencies and the fundamental buckling voltage are derived for simple support conditions. In addition, an explicit relationship between the residual surface tension and the small scale parameter of the piezoelectric NW, in terms of the critical electric potential at which the axial buckling occurs, is offered. Accordingly, a design chart is presented which may assist in experimental characterization of the mechanical properties of piezoelectric NW-based devices.