氮流量对ZnO∶N薄膜微结构及光学性能影响

运用射频磁控溅射技术,改变氩、氮流量比(9/1 ～ 9/4)在玻璃衬底上获得ZnO∶N样品,采用XRD、紫外-可见分光光度计、傅里叶红外光谱仪及SEM对薄膜微结构和光学性能表征.结果发现∶N流量小,样品XRD峰强小,峰位不明显,紫外可见光光谱在320 ～780 nm波长区间透射率变化小;随着N流量的增加,样品XRD有(002)强单峰出现,在400 nm波长以下透射率急剧下降;当氩氮流量达到9/4,样品XRD出现双峰,紫外光透射率无明显变化.     

射频磁控溅射生长ZnO薄膜及性能研究

采用射频磁控溅射技术在玻璃衬底生长ZnO及ZnO∶ Al薄膜,通过改变氩氧比、衬底温度和溅射功率获得样品.用X射线衍射仪、紫外-可见分光光度计、扫描电子显微镜进行表征.结果发现:室温下40W的溅射功率1h的溅射时间,改变氩氧比获得样品.XRD图谱中无明显衍射峰出现;紫外可见光分光光度计测试结果显示400nm波长以下,透光率在90;以上.说明薄膜生长呈无定形.衬底温度高于200℃样品,XRD有明显(002)衍射峰出现,在400～ 800 nm波长范围,透光率在88;以上,衬底温度300℃时,XRD衍射峰半高宽最小,晶粒尺寸大.TEM显示:衬底300℃晶粒尺寸最大,晶体发育好.在200℃掺铝ZnO薄膜,(002)峰不明显,有(101)峰出现.     

B掺杂对平面结构MOCVD-ZnO薄膜性能的影响

本文研究了B2H6掺杂流量(B掺杂)对平面结构MOCVD-ZnO薄膜的微观结构和光电性能影响.XRD、SEM和AFM测试的研究结果表明,玻璃衬底上制备的ZnO薄膜具有(002)峰择优取向的平面结构,B掺杂使薄膜的球状晶粒尺寸变小,10 sccm流量时晶粒尺寸为～15 nm.ZnO:B薄膜的最小电阻率为5.7×10-3Ω·cm.生长的ZnO薄膜(厚度d=1150 nm)在400～900 nm范围的透过率为82;～97;,且随着B2H6掺杂流量增大,光学吸收边呈现蓝移(即光学带隙Eg展宽)现象.     

磁控溅射Cu薄膜的光电性能研究

利用磁控溅射技术,通过正交试验设计方法,在K9光学玻璃基底上制备了Cu薄膜,研究了溅射时间、基底温度和氩气流量对Cu薄膜光电性能的影响.研究表明:Cu薄膜的透射谱在紫外波段362 nm处有明显吸收峰,但在可见光波段吸收强度较弱,说明Cu膜在可见波段有较高的透光性;膜厚度增加则光学透射率降低.电阻率随膜厚的增大,大体上呈逐渐减小的趋势;1100 nm 为临界尺寸,Cu膜厚度<1100 nm时,电阻率值变化较快;Cu薄膜厚度>1100 nm时,电阻率变化缓慢至定值.当溅射时间为25 min、基底温度为300 ℃、氩气流量为6.9 sccm时所得样品在紫外-可见光区没有吸收,且导电性好.     

射频反应磁控溅射制备ZnO薄膜的微结构及其光学性能

采用射频反应磁控溅射技术在石英和Si衬底上制备了高度c轴择优取向的ZnO薄膜,样品的氧氩流量比分别为10:40,20:40,30:40,40:40.利用X射线衍射仪、表面轮廓仪、原子力显微镜和紫外-可见分光光度计研究了样品的微结构与光学特性.研究表明:氧氩流量比为30:40的样品结晶质量最好.所制备的ZnO薄膜的可见光平均透射率均大于87;.随着氧氩流量比的增大,薄膜的透射率呈非单调变化,氧氩流量比为30:40的样品在可见光范围的平均透射率可达93;.光学带隙随着氧氩流量比的增大,先增大后减小.与块材ZnO的带隙(3.37 eV)相比,ZnO薄膜的带隙均变窄.     

衬底温度对硼掺杂ZnO薄膜微观结构及其光电特性的影响

采用射频磁控溅射技术,改变玻璃衬底温度制备B掺杂ZnO薄膜,薄膜的微结构及其光电性能分别用X-射线衍射仪、紫外-可见分光光度计、四探针测试仪及粗糙度测试仪进行表征.结果表明:ZnO∶B薄膜样品表面平整,具有六角纤锌矿结构并呈C轴择优取向.所有薄膜样品在420 ～ 900 nm区间内的平均透光率大于91;.随着温度的增加,电阻率先减小后增大,但晶粒尺寸一直变大.衬底温度为100℃时电阻率可低至1.14×10-3Ω·cm,所有样品禁带宽度相对于本征ZnO蓝移.     

Fe、Ni共掺杂ZnO薄膜的溶胶-凝胶法制备及性能研究

采用溶胶-凝胶法在玻璃基片上旋涂生长了ZnO、Fe, Ni单掺杂及(Fe,Ni)共掺杂ZnO薄膜.产物的显微照片及XRD图谱结果表明, 该方法所制备的ZnO薄膜表面均匀致密,都存在(002)择优取向,具有六角纤锌矿结构,晶粒尺寸平均在13 nm 左右,振动样品磁强计(VSM)测试结果显示掺杂ZnO薄膜均存在室温铁磁性.光致发光(PL)测量表明所有样品薄膜的PL谱主要由较强的紫外发光峰(394 nm)、蓝光峰(420 nm)、绿光峰(480 nm)组成.Fe、Ni单掺杂和共掺杂并不改变ZnO薄膜的发光峰位置,但掺杂后该紫外发光峰减弱,420 nm处的蓝光峰增强.     

在钛酸锶衬底上外延生长ZnO薄膜及其性能研究

用脉冲激光淀积法(PLD)在(111)面SrTiO3衬底上外延生长ZnO单晶薄膜.样品分别在衬底温度为350℃、500℃、600℃下外延生长.X射线衍射(XRD)的结果表明,所得的ZnO单晶薄膜结晶性能好,只出现(002)和(004)两个衍射峰,(002)峰的半高宽度(FWHM)为0.23°.在荧光光谱中我们只观察到来源于带边激子跃迁的强UV发射,并且随着生长温度的升高,紫外峰的强度逐渐增强.样品的SEM图像表明所得ZnO薄膜表面平整,晶粒均匀.衬底温度为600℃时,所得到的ZnO薄膜结构完整,晶粒尺寸最大,均匀;而且紫外发射最强.     

溶胶-凝胶法制备MgxZn1-xO及其特性

采用溶胶-凝胶法制备了不同组分(x=0.1～0.3)的MgxZn1-xO前驱体,并对它进行不同温度的热处理(550℃～1000℃).X射线衍射(XRD)结果表明,Mg0.1Zn0.9O具有和ZnO一样的衍射谱,为六方纤锌矿结构,而且随着热处理温度的升高,ZnO衍射峰的强度逐渐增强,半高宽不断减小;Mg元素掺杂浓度增大后,出现了MgO的峰位.扫描电子显微镜(SEM)显示Mg0.1Zn0.9O晶粒粒径分布较均匀;热处理温度升高,晶粒的尺寸不断变大.用室温荧光光谱(PL)分析了经过550～1000℃热处理获得的Mg0.1Zn0.9O粉末,结果发现除了550℃下处理的样品,其它都有紫外发射峰(350nm左右),而且随着热处理温度的升高紫外峰有明显的蓝移现象.     

MOCVD法在(220)CaF2衬底上生长ZnO薄膜及其性能研究

采用金属有机化学汽相沉积(MOCVD)法在(220)CaF2衬底上外延生长ZnO薄膜.利用X射线衍射(XRD)、紫外-可见光谱和光致发光谱(PL)对ZnO薄膜的结构和光学性能进行了分析.XRD结果表明,所制备的ZnO薄膜结晶性能良好,具有高度的(002)的择优取向,002衍射峰的半高宽(FMHM)为0.115°.所制备的ZnO薄膜透明,透过率超过85;.在常温的(He-Cd激光器)PL谱中,只有378.5 nm的带边发射.用同步辐射光源测试的真空紫外光谱中,在低温20K时,出现218 nm、368 nm、418 nm、554 nm发光峰,其中368 nm峰强度随着温度的升高强度逐渐下降,到常温时几乎消失.     

Modelling of mechanism of agglomeration of KCl crystallization

The article presents an analysis into agglomeration during KCl vacuum crystallization. The theoretical and experimental investigations into the mechanism of agglomeration during mass crystallization result in an extension of the growth phenomena within the known model equations. The basis for this is essentially constituted by the collision model concepts of the theory of floculation in disperse systems. The parameters derived from the microprocess analysis (energy dissipation, content of solids, growth rate of individual grains) lead to model equations which are confirmed by laboratory and test trials.     

Relationship of Morphological Types of Dynamic Forms of Crystals

Crystallography Reports - The relationship of morphological spectra (sets of data on the morphological types of real polyhedral crystals and their probabilities under current physicochemical...     

Velocities of Disappearance and Lifetime of Faces of Growing Crystals

The formulae for absolute R_disap and relative R velocities of disappearance and lifetime τ of faces of growing crystals have been derived for stationary growth. It was shown that the quantities are determined by the relative growth velocity R_A/R_critA of the vanishing face A with respect to the critical growth velocity R_critA and by the geometry of a crystal expressed by the trigonometric functions of interfacial angles β and γ formed between face A and the adjacent faces. R increases and τ decreases with the increase in R_A/R_critA to certain limiting values. The calculations have been verified and illustrated by the experimental results for triclinic potassium bichromate (KBC) crystals. Results enable ones to predict values of velocities of disappearance and lifetimes of undesirable, supplementary faces of any real crystal.     

Development of Pauling's concepts of geometric characteristics of atoms

The evolution of the geometric characteristics introduced by Pauling and their dependence on the specific features of the structure and chemical bonds have been considered. The values of the covalent and van der Waals radii are given as well as their relationships and mutual transitions.     

A review of measurement of thermophysical properties of silicon melt

Measurements of thermophysical properties of Si melt and supplementary study of X-ray scattering/diffraction by the authors' group were reviewed. The values obtained differed variously from those of literature. Density was 2–3% larger, surface tension 20–30% smaller, viscosity up to 40% larger, electrical conductivity 8% smaller, spectral emissivity more or less in good agreement with literature values, and thermal diffusivity a few percent larger. An anomalous density jump was found near the melting point. Surface tension and viscosity also showed anomaly. A strange time-dependent change of density was observed over 3 h after melting. X-ray analyses suggested a slight change in local atom ordering, but showed no sign of cluster formation. An addition of 0.1 at% gallium caused the density jump to disappear, while that of boron caused no change. An EXAFS study of the former melt indicated a strong interaction between Ga and Si atoms as if molecules of GaSi₃ existed. The implications of the measured properties are a possibility of soft-turbulence in an Si melt in a relatively large crucible, a more complicated manner of intake of oxygen depleted molten Si from the free surface region to underneath the growing crystal, and a relaxation of the melt after melting arising from trapped gas species.     

Dependence of the parameters of equations of viscous flow on chemical composition of silicate melts

The temperature dependence of viscosity of silicate melts is discussed in the framework of the Avramov–Milchev (AM) equation. The composition is described by means of two parameters: the molar fraction, x, and the “lubricant fraction”, l. The molar fraction is the sum of the molar parts x_i of all oxides dissolved in SiO₂, the molar fraction of the latter being 1 ? x. It is shown that, with sufficient precision, two of the parameters of the AM equation can be presented as unique functions of the molar fraction. On the other hand, x is not sufficient to determine properly the reference temperature T_r , at which viscosity is η_r = 10¹³ [dPa.s]. Therefore, additional parameter, “lubricant fraction” l, is introduced. For each of the components, l_i is a product of molar part x_i and a specific dimensionless coefficient 0 ≤ k_i ≤ 1 accounting for the specific contribution of this component to the increased mobility of the system. It is demonstrated that, for l > 0, the reference temperature is related to the “lubricant fraction” l through the reference temperature T_r,SiO2 of pure SiO₂.     

Comparative analysis of two methods of calculation of the orientation of domain walls in ferroelastics

Two types of domain-wall equations are analyzed: the equations derived by the Sapriel method and the equations obtained by interface matching of the thermal-expansion tensor. It is shown that, for W-type domain walls, these methods yield the same equations. For W′-type domain walls, the equations obtained by different methods coincide for proper ferroelastics and differ for improper ferroelastics.     

Generation of crystal structures of heteromolecular compounds by the method of discrete modeling of packings

Within the method of discrete modeling of packings, an algorithm of generation of possible crystal structures of heteromolecular compounds containing two or three molecules in the primitive unit cell, one of which has an arbitrary shape and the other (two others) has a shape close to spherical, is proposed. On the basis of this algorithm, a software package for personal computers is developed. This package has been approved for a number of compounds, investigated previously by X-ray diffraction analysis. The results of generation of structures of five compounds—four organic salts (with one or two spherical anions) and one solvate—are represented.