Structural and optical properties of Zn(Mg,Cd)O alloy films grown by remote-plasma-enhanced MOCVD

We report the structural and optical properties of wurtzite-structure Zn(Mg,Cd)O ternary alloys. Wurtzite (0 0 0 1) Zn_1−xCd_xO and Mg_yZn_1−yO films were grown on (11–20) sapphire substrates using remote-plasma-enhanced metalorganic chemical vapor deposition. The large bowing parameters of Zn_1−xCd_xO and Mg_yZn_1−yO ternary alloys are 3.0 and 3.5, respectively, which reflects the large difference of each binary’s electronegativity. We have analyzed the broadening of photoluminescence (PL) in Zn(Mg,Cd)O alloys on alloy content by taking into account the statistical alloy fluctuation and the localization of the exciton, and have clarified that the localization of the exciton strongly affects to PL full-width at half-maximum (FWHM) in Zn(Mg,Cd)O alloys. The alloy broadenings in steady-state PL of Zn(Mg,Cd)O alloys are in good agreement with the calculated tendency by the theoretical model based on the statistical alloy fluctuation, while PL FWHM of Zn_1−xCd_xO is three times larger than the calculated results. Moreover, as another way to confirm alloy broadening, we also have done time-resolved PL measurements and derived the localized depth of the exciton in ZnO-based system, indicating a good agreement with the tendency of PL FWHM broadening.     

Electrical and optical properties of Cd1−xZnxS (0x0.18) grown by chemical bath deposition

Cd_1−xZn_xS films with 0x0.18 were grown by chemical bath deposition technique on glass substrates from an aqueous solution containing cadmium and zinc sulfate, ammonia and thiourea. Microstructural features, obtained from X-ray diffraction and scanning electron microscopy (SEM) measurements, reveal a predominance of Wurtzite structure and an homogenous microstructure formed by densely microcrystallines for all the samples studied. Cd_1−xZn_xS semiconductor was found to be resistive and of n-type. Also, the electron density decreases with increased x and the mobility reaches a maximum around x=0.12. Which means that the Cd_1−xZn_xS films at this composition are of high crystalline quality, i.e. having reduced intrinsic defect concentrations.     

Effect of rapid thermal annealing on Zn1‐xCdxO layers grown by radio‐frequency magnetron co‐sputtering

Zn_1‐xCd_xO layers were deposited on the sapphire substrate using the radio‐frequency magnetron co‐sputtering system. The grown Zn_1‐xCd_xO layers were carried out in the post‐annealing treatment for 1 min at the 800 °C oxygen‐ambient by the rapid thermal annealing (RTA) method. X‐ray diffraction (XRD) experiment shows that the Zn_1‐xCd_xO layers are changed from the single phase of the hexagonal structure at 0≤x ≤0.08 to the double phase of hexagonal‐and‐cubic structure at x =0.13. Thus, the maximum Cd‐composition ratio with the hexagonal structure was found out to be x =0.08. Also, the crystallinity of Zn_1‐xCd_xO layers at x =0.13 was remarkably improved by the RTA annealing treatment. This crystal quality improvement was thought to be associated with the relaxation of the compressive strain remaining in the Zn_1‐xCd_xO layers. Therefore, the results of XRD and transmittance lead that the crystal quality of the Zn_1‐xCd_xO layers forming the hexagonal ZnO phase is better than that forming the cubic CdO phase. Consequently, the reliable formation and the crystallinity of the Zn_1‐xCd_xO layers were achieved by using the RTA method of short‐time thermal‐annealing at the high temperature. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Investigation of II –VI alloy lattice dynamics by IR spectroscopic ellipsometry

Optical properties related to lattice vibrations of bulk Zn_1‐xBe_xSe, Zn_1‐x‐yBe_xMn_ySe and Cd_1‐xBe_xSe alloys are reported. Optical phonons of the mixed crystals grown by the Bridgman method have been investigated by infrared spectroscopic ellipsometry in the wave‐number range 300‐8000 cm^‐1. The complex dielectric functions can be reproduced using a model with two or three classical damped oscillators corresponding to the BeSe‐like transverse‐optical phonon‐modes and a Drude contribution from the free carriers. The frequencies of longitudinal‐optical phonons have been found from the imaginary parts of the dielectric loss functions. The influence of the alloy composition on the zone‐centre optical phonon frequencies is discussed. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structure and optical properties of Mg‐doped ZnO nanoparticles by polyacrylamide method

Mg‐doped ZnO (Mg_xZn_1‐xO) nanoparticles with precise stoichiometry are synthesized through polyacrylamide polymer method. Calcination of the polymer precursor at 650 °C gives particles of the homogeneous solid solution of the (Mg_xZn_1‐xO) system in the composition range (x < 0.15). ZnO doping with Mg causes shrinkage of lattice parameter c. The synthesized Mg_xZn_1‐xO nanoparticles are typically with the diameter of 70–85 nm. Blue shift of band gap with the Mg‐content is demonstrated, and photoluminescence (PL) from ZnO has been found to be tunable in a wide range from green to blue through Mg doping. The blue‐related PL therefore appeared to be caused by energetic shifts of the valence band and/or the conduction band of ZnO. Mg_xZn_1‐xO nanoparticles synthesized by polyacrylamide‐gel method after modified by polyethylene glycol surfactant have a remarkable improvement of stability in the ethanol solvent, indicating that these MZO nanoparticles could be considered as the candidate for the application of solution–processed technologies for optoelectronics at ambient temperature conditions.     

Photoelectric and photothermal investigations of Zn1‐x‐yBexMnySe solid solutions

Zn_1‐x‐yBe_xMn_ySe solid solutions were grown from the melt by the high pressure Bridgman method. Optical, luminescence, photoelectric and photothermal properties of this material were investigated. Interpretation of the piezoelectrically detected photoacoustic spectra was performed using Jackson and Amer theory. From the spectral dependence of the amplitude and phase of photoacoustic signal as well as from photoluminescence spectra the variation of energy gap with composition was determined. The values of thermal diffusivity were derived from the dependence of photoacoustic signal on modulation frequency of the laser radiation illuminating the sample. The photoluminescence‐excitation spectra and photoconductivity spectra were measured. The origin of luminescence in Zn_1‐x‐yBe_xMn_ySe was discussed. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Optical and magnetic properties of Nd‐doped ZnO nanoparticles

Nd‐doped ZnO nanoparticles with different concentration were synthesized by sol‐gel method. The structures, magnetic and optical properties of as‐synthesized nanorods were investigated. X‐ray diffraction (XRD) and x‐ray photoelectron spectroscopy (XPS) results demonstrated that Nd ions were incorporated into ZnO lattice; but Zn_1‐xNd_xO nanoparticles with Nd concentration of x = 0.05 showed Nd₂O₃ phase, so the saturation concentration of Nd in Zn_1‐xNd_xO is less than 5 at%. Vibrating sample magnetometer (VSM) measurements indicated that Nd doped ZnO possessed dilute ferromagnetis behaviour at room temperature. Photoluminescence spectroscopy (PL) showed that Nd ions doping induced a red slight shift and decrease in UV emission with increase of Nd concentration.     

Some structural considerations on the perovskite‐type A1‐ySryCo1‐xFexO3‐δ solid solution series

Solid solution series of La_1‐ySr_yCo_1‐xFe_xO_3‐δ were extensively studied in the past as cathode materials for solid oxide fuel cells. However, the crystal structure behavior of La_1‐ySr_yCo_1‐xFe_xO_3‐δ solid solution series when La‐ions are replaced with another rare‐earth ion or metallic alkaline earth metal is at present not fully understood. Here we report X‐ray powder diffraction measurements performed on samples of the Sm_0.8Sr_0.2Co_1‐xFe_xO_3‐δ solid solution series. This study demonstrates that the average A‐cation radius, as well as the Fe content (x), affects the structural modification of the A_1‐ySr_yCo_1‐xFe_xO_3+δ solid solution series significantly. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Zn1−xCdx polytype single crystals with various degree of order

The results of X-ray investigations of the polytype structures formed in solid solutions of Zn_1–xCd_xSe are presented. For compositions of 0.22 < x < 0.35 polytypes 8H, 6H, 4H, and DS (disordered structure) are present. The Zn_1–xCd_xS single crystals of 0 ≦ x ≦ 0 were obtained by Bridgman's method under high protective argon pressure from the melt. The structures are characterised by FARKASZ -JAHNKE statistical parameters π(m,p), and by parameters P_LH of the polytype unit cell formation probability.     

Multimode phonon structure of Be‐containing II ‐ VI mixed crystals determined by IR spectroscopic ellipsometry

Spectroscopic ellipsometry in the infrared spectral range 250‐5000 cm^‐1 is used for analysis of the dielectric response of Zn_1‐x‐yBe_xMg_ySe and Zn_1‐x‐yBe_xMn_ySe crystals grown by a high‐pressure Bridgman method. Ellipsometric spectra display features in the spectral range 390‐500 cm^‐1 associated with BeSe‐type phonon modes. In the optical spectra of Zn_1‐x‐yBe_xMg_ySe crystals both BeSe‐type and MgSe‐type lattice absorption bands are detected. The MgSe‐like modes are located at approximately 300 cm^‐1. The complex dielectric functions can be reproduced using a model with two or three and one or two classical damped oscillators corresponding to the BeSe‐like and the MgSe‐like transverse‐optical phonon modes, respectively. The frequencies of longitudinal‐optical phonons have been derived from the dielectric loss functions. A red‐shift of the BeSe‐like phonons frequencies with a mean rate 0.42 cm^‐1 (0.50 cm^‐1) per mole percent of Mg (Mn) incorporated to the alloy has been found for examined concentration range x, y ≤ 0.25. A noticeable damping the intensities of BeSe‐type modes with increasing fraction of Mg and Mn dopant is observed in comparison to the strengths of BeSe‐type modes in Zn_1‐xBe_xSe crystals. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Monocrystalline Cd0.2Zn0.8Te solid solution obtained by self‐selecting vapour growth

Cd_0.2Zn_0.8Te monocrystals with the sizes of about 15 mm have been produced by self‐selecting vapour growth (SSVG). High degree of structural perfection of monocrystalline Cd_0.2Zn_0.8Te was achieved. Excellent compositional uniformity was observed as well. To our knowledge, no comparable results are reported for this solid solution. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

On the dispersion of the refractive index in AIIBVI thin films

We propose a new calculation following traditional methods for deducing refractive index from the fringe pattern of the transmission spectrum of a thin transparent CdS, ZnS, and Zn_xCd_1−xS film surrounded by nonabsorbing media. The error in the refractive index measurements is 4–5%. We have found that polycrystalline CdS, ZnS, and Zn_xCd_1−xS evaporated films have refractive index different from those of single crystal material.     

X-ray investigation of the mechanisms of phase transformations in single crystals of ZnS,ZnxCd1−xS,and ZnxMn1−xS (II). Comparison of observed and calculated diffraction effects

The experimentally observed intensity profiles recorded from ZnS, Zn_xCd_1−xS and Zn_xMn_1−xS crystals at different stages of the 2H-3C and 2H-6H transformations are compared with those computed theoretically from the three parameter model in the previous paper. It is found that the 2H-3C and 2H-6H transformations occur by the nonrandom nucleation of deformation faults. The probability of the growth of a nucleus is much greater than that of the creation of a fresh nucleus. At least two different fault probabilities have therefore to be employed in computing the diffraction effects in each case. The transformation behaviour of Zn_xCd_1−xS and Zn_xMn_1−xS crystals is strongly influenced by variations in stoichiometry (x). Large values of x (x > 0.95) favour the 2H-3C transformation, whereas smaller values (x ≦ 0.94) favour the formation of the 6H phase. A comparison of the calculated and observed intensity distributions indicates that in some crystals the 2H-3C and 2H-6H transformations occur simultaneously in different regions of the same single crystal.     

X‐ray studies on quaternary system RbXK1‐XBrYCl1‐Y

Single crystals of the quaternary crystalline solid solution system Rb_xK_1‐xBr_yCl_1‐y have been grown by melt technique for three different compositions y = 0.25, 0.50 and 0.75, keeping x = 0.5 and X‐ray diffraction studies have been carried out for each case independently, using spherically ground single crystals. The results indicate an enhancement of Debye‐Waller B(total) factors for the compositions y = 0.25 and 0.75 whereas for the intermediate composition, y = 0.5, the factor B(total) is close to the end member value. This experimental investigation show that for this composition, the crystalline solid solution behaves like an end member crystal.     

Mechanism of formation of barium cuprate-based solid solutions with perovskite-like structure doped with cadmium and yttrium oxides

The influence of Y₂O₃ and CdO content on the phase composition, structure, and electrical properties of Y₂O₃-CdO-BaO-CuO ceramics was studied. The concentration limits of the existence of the orthorhombic perovskite-like Y_xBa_{2 ? x} Cd_yCu_{1 ? y} O_{3 + δ} solid solutions (where 0.20 ≤ x ≤ 0.37 and y ≤ 0.2) and their unit-cell parameters are determined.     

Properties of Hg1‐xCdxTe epitaxial films grown on (211)CdTe and (211)CdZnTe

Hg_1‐xCd_xTe (MCT) epitaxial films have been grown employing single crystalline substrates of CdTe and Cd_0.96Zn_0.04Te with (211)Cd and (211)Te crystalline orientations. The Isothermal Vapor Phase Epitaxy (ISOVPE) technique without Hg overpressure has been used for the epitaxial growth. Substrates and films were characterized by optical microscopy, chemical etching and x ray diffraction (Laue technique). The electrical properties were determined by Hall effect measurements. The characterization results allowed to evaluate the crystalline quality of MCT films. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Investigations on the homogeneity of single crystals of materials with variable composition grown by chemical transport reactions

To investigate the problem of homogeneity in crystals grown by chemical transport reactions (CTR) solid solutions Fe_1-yCo_yS, Fe_1-yNi_yS, and Zn_1-yCo_yO were choosen as model substances. Relative concentration profiles of Co and Ni, respectively, were measured by electron-probe microanalysis and light absorption (in Zn_1-yCo_yO only). No significant deviations from homogeneity were found for Fe_1-yMe_yS, whereas in Zn_1-yCo_yO the Co contents increase in the growth direction. A qualitative explanation due to different diffusivities in the solids can be given.     

Effect of annealing and composition on crystal structure,surface morphology and optical absorption of chemically deposited Cd1‐xSnxS films

Cd_1‐xSn_xS thin films were successfully deposited on suitably cleaned glass substrate by chemical bath deposition method at 74 °C. Hydrated Stannous Chloride (SnCl₂.2H₂O) in aqueous solution was added to the CdS growing solution in different proportions. The experimental results indicate, a successful doping for lower concentration of Sn, saturation for intermediate doping levels, and a degradation of the doping process for higher concentration of Sn. Indirect (X‐ray diffraction) and Direct (Scanning electron microscopy) measurements were performed to characterize the growth and the nature of crystallinity of the different Cd_1‐xSn_xS films. The effect of annealing on the crystal structure and morphology of the deposited films has also been discussed. The X‐ray diffraction spectra show that the thin films are polycrystalline and have both cubic and hexagonal structure. The Interplanar spacing, lattice constant, grain size, strain, and dislocation density were calculated for as‐deposited and annealed films. The grain size was found to decrease from 5 nm to 0.89 nm with doping concentration of Sn. The grain size further decreased due to annealing at 400 °C. SEM studies show layered growth and long needle like structures along with some voids. After annealing the densification and smaller size of the particles was also observed. The optical absorption spectra show shifting of absorption peaks towards lower wavelength side (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Electrical transport in Bi doped n-type amorphous semiconductors (GeSe3.5)100−xBix at high pressure

Electrical transport in Bi doped amorphous semiconductors (GeSe_3.5)_100?xBi_x (x=0,4,10) is studied in a Bridgman anvil system up to a pressure of 90 kbar and down to 77 K. A pressure induced continuous transition from an amorphous semiconductor to a metal-like solid is observed in GeSe_3.5. The addition of Bi disturbs significantly the behaviour of resistivity with pressure. The results are discussed in the light of molecular cluster model for Ge_ySe_1?y proposed by Phillips.     

Structure and electrical properties of Mg‐doped ZnO nanoparticles

Mg_xZn_1‐xO (x=0.01‐0.3) nanoparticles were synthesized by the sol‐gel technique using solutions of Mg and Zn based organometalic compounds. The electrical properties of Mg doped zinc oxide (ZnO) were studied within wide temperature range from 300 to 500 K under the N₂ gas flow (flow rate: 20 sccm) and in the frequency range from 40 Hz to 1 MHz for ac electrical measurements. The dc conductivities and the activation energies were found to be in the range of 10^‐9‐10^‐6 S/cm at the room temperature and 0.26‐0.86 eV respectively depending on doping rate of these samples. The ac conductivity was well represented by the power law Aω^s. The conduction mechanism for all doped ZnO could be related to correlated barrier hopping (CBH) model. The complex impedance plots (Nyquist plot) showed the data points lying on a single semicircle, implying the response originated from a single capacitive element corresponding to the nanoparticle grains. The crystal structures of the Mg_xZn_1‐xO nanoparticles were characterized using X‐ray diffraction. The calculated average particle sizes values of Zn_1‐xMg_xO samples are found between 29.72 and 22.43 nm using the Sherrer equation. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)