Effect of Calcination Temperature on Catalytic Activity and Textual Property of Cu/HMOR Catalysts in Dimethyl Ether Carbonylation Reaction

The effect of calcination temperature on the catalytic activity for the dimethyl ether (DME) carbonylation into methyl acetate (MA) was investigated over mordenite supported copper (Cu/HMOR) prepared by ion-exchange process. The results showed that the catalytic activ-ity was obviously affected by the calcination temperature. The maximal DME conversion of 97.2% and the MA selectivity of 97.9% were obtained over the Cu/HMOR calcined at 430 oC under conditions of 210 oC, 1.5 MPa, and GSHV of 4883 h^-1. The obtained Cu/HMOR catalysts were characterized by powder X-ray diffraction, N₂ absorption, NH₃ temperature program desorption, CO temperature program desorption, and Raman techniques. Proper calcination temperature was effective to promote copper ions migration and diffusion, and led the support HMOR to possess more acid activity sites, which exhibited the complete decomposing of copper nitrate, large surface area and optimum micropore structure, more amount of CO adsorption site and proper amount of weak acid centers.     

Highly Ordered Mesoporous Cobalt-Copper Composite Oxides for Preferential CO Oxidation

Highly ordered mesoporous cobalt-copper composite oxides were prepared by the nanocasting method with various Co and Cu ratios. The catalysts obtained were characterized by X-ray diffraction, N₂ adsorption–desorption, H₂-temperature programmed reduction, CO-temperature programmed desorption and X-ray photoelectron spectroscopy. All of the catalysts had uniform mesopores and high surface areas. The distinct catalytic properties of these well-characterized mesoporous materials were demonstrated for preferential CO oxidation. It is found that the mesoporous cobalt-copper composite oxides, exhibited the higher catalytic activity for CO conversion and selectivity compared with the mesoporous Co₃O₄ and mesoporous CuO. Among these catalysts the mesoporous cobalt-copper catalyst with Co:Cu molar ratio of 70:30, shows the best catalytic activity and the broadest operating temperature “window” for the high CO conversion in the range of 125–200^oC. The higher catalytic activity was attributed to the higher CO adsorption and oxygen vacancies.     

预吸附吡啶增强二甲醚在丝光沸石上羰基化反应的稳定性

 对比研究了二甲醚在氢型丝光沸石和吡啶修饰的氢型丝光沸石上的二甲醚羰基化反应. 结果表明, 吡啶预吸附大大提高了二甲醚羰基化反应的稳定性, 并且在 473 K 反应 48 h 能够保持约 30% 的乙酸甲酯收率. 原位红外光谱和 NH3 程序升温脱附研究发现,吡啶吸附在 12 元环内, 而 8 元环内的酸性位基本不受干扰. 129Xe 核磁共振研究表明, 未经修饰的丝光沸石反应后孔道严重堵塞, 而吡啶修饰的分子筛反应后孔道基本不变. 因此, 12 元环内酸性位是积炭失活位, 吡啶吸附抑制了 12 元环内积炭的生成, 二甲醚羰基化反应能够在 8 元环内活性位上顺利进行.     

Study of nano‐Cu/SiO2 catalysts for highly selective hydrogenation of acetophenone

Hydrogenation of acetophenone over nano‐Cu/SiO₂ catalysts was investigated. The catalysts, prepared by a liquid precipitation method using various precipitating agents, were characterized using low‐temperature nitrogen adsorption, X‐ray diffraction, temperature‐programmed desorption of ammonia, hydrogen temperature‐programmed reduction, transmission electron microscopy and X‐ray photoelectron spectroscopy. It was found that the catalysts prepared by a homogeneous precipitation method had better activity and stability than those prepared by a co‐precipitation method. The catalyst prepared using urea as precipitating agent had well‐dispersed copper species, high surface area and abundant pore structure. The catalytic performance and mechanism of the Cu/SiO₂ catalysts were further studied. It was found that the activity and stability of the catalysts could be improved by adjusting the proportion of Cu⁺/(Cu⁺ + Cu⁰). The sample prepared using urea as precipitating agent presented higher activity and selectivity. Also, the catalyst prepared using urea maintained a high catalytic performance while being continuously used for 150 h under the optimal reaction conditions.     

制备方法对Co-MOR催化剂CH4选择还原NO性能的影响

采用离子交换法、浸渍法制备一系列的Co-MOR 催化剂, 并将其用于CH₄选择性催化还原 NO_x(CH₄-SCR)反应. 运用X 射线衍射(XRD)、X 射线荧光光谱(XRF)、扫描电子显微镜(SEM)、紫外-拉曼(UVRaman)光谱、X射线光电子能谱(XPS)、NO程序升温脱附(NO-TPD)等手段对催化剂进行了表征. 结果表明, 浸渍法制备的催化剂, Co以Co₃O₄形式存在; 而离子交换法制备的催化剂, Co以离子形式进入丝光沸石(MOR)骨架之中, 在催化剂上形成更多的Co²⁺和[Co-O-Co]²⁺, 形成更均匀NO吸附中心和CH₄-SCR反应活性中心. 催化剂活性评价表明离子交换法制备的催化剂具有更宽的活性温度区间, Co(0.30)-MOR 催化剂在327-450℃温度范围内NO转化率大于50%.     

淀粉基炭负载纳米铜催化合成碳酸二甲酯

以硝酸铜和可溶性淀粉为原料, 经过溶胶-凝胶化过程、高温炭化和KOH活化得到炭负载铜催化剂(Cu/C), 采用扫描电镜、透射电镜、X射线衍射、热重-差热分析仪、N₂吸附和CO程序升温脱附对催化剂结构进行了表征, 并考察了它在甲醇氧化羰基化合成碳酸二甲酯(DMC)反应中的催化活性. 结果表明, 活化温度和KOH用量对催化剂的表面结构及金属铜粒子尺寸影响显著, 当活化温度为850℃, KOH:C=1 (质量比)时, Cu/C催化剂的比表面积达到1690 m²/g, 铜纳米粒子平均晶粒尺寸为30.4 nm, 催化活性最高, DMC时空收率达到235.7 mg·g^-1·h^-1, 甲醇转化率和DMC选择性分别为1.6%和76.5%.     

Study of catalytic hydrodeoxygenation performance for the Ni/KIT-6 catalysts

Ni/KIT-6 catalysts loaded with different amounts of metallic Ni were prepared by impregnation method. The prepared catalysts and their precursors were investigated through wide- and low-angle XRD, TEM, BET, H₂-TPR, and H₂-TPD analyzes. The catalytic hydrodeoxygenation performance of the catalysts was evaluated using ethyl acetate as a model bio oil compound. Results indicate that the catalytic hydrodeoxygenation performance of the prepared catalysts was directly related to hydrogen storage properties, hydrogen desorption properties, dispersion of the active component Ni, and so on. The ethyl acetate conversion and ethane selectivity of 25?wt% Ni/KIT-6 catalyst were 100 and 96.8%, respectively, at 300?°C, which shows the best performance. The hydrodeoxygenation activity of ethyl acetate was higher than that of methyl acetate and isopropyl acetate because of the effect of molecular polarity and size. And, this reaction is a structure sensitive reaction.     

Investigation of Fe−Ni Mixed‐Oxide Catalysts for the Reduction of NO by CO: Physicochemical Properties and Catalytic Performance

A series of Fe?Ni mixed‐oxide catalysts were synthesized by using the sol–gel method for the reduction of NO by CO. These Fe?Ni mixed‐oxide catalysts exhibited tremendously enhanced catalytic performance compared to monometallic catalysts that were prepared by using the same method. The effects of Fe/Ni molar ratio and calcination temperature on the catalytic activity were examined and the physicochemical properties of the catalysts were characterized by using XRD, Raman spectroscopy, N₂‐adsorption/‐desorption isotherms, temperature‐programmed reduction with hydrogen (H₂‐TPR), temperature‐programmed desorption of nitric oxide (NO‐TPD), and X‐ray photoelectron spectroscopy (XPS). The results indicated that the reduction behavior, surface oxygen species, and surface chemical valence states of iron and nickel in the catalysts were the key factors in the NO elimination. Fe_0.5Ni_0.5O_x that was calcined at 250 °C exhibited excellent catalytic activity of 100 % NO conversion at 130 °C and a lifetime of more than 40 hours. A plausible mechanism for the reduction of NO by CO over the Fe?Ni mixed‐oxide catalysts is proposed, based on XPS and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analyses.     

Effect of anions on the structure and catalytic properties of a La-doped Cu-Mn catalyst in the water-gas shift reaction

Effects of the anion type on the structure, thermal stability, and catalytic performance of La-doped Cu-Mn catalysts prepared by co-precipitation were characterized by X-ray diffraction, Brunauer-Emmett-Teller, temperature-programmed reduction, temperature-programmed reduction of oxidized surfaces, and temperature-programmed desorption. The Cu-Mn catalyst was tested for the water-gas shift (WGS) reaction. The main crystalline phase of samples prepared with sulfate, acetate, chloride, and nitrate as the starting materials was a Cu_1.5Mn_1.5O₄ spinel structure, following the WGS reaction, the main crystalline phases were transformed into Cu and MnO. The sample prepared with acetate as the starting material showed the most obvious MnCO₃ characteristic diffraction peaks, with better synergistic effects of Cu and MnO, increased adsorption of CO₂ and improved dispersion of Cu on the catalyst surface; also, the best thermal stability and the highest low temperature catalytic activity were observed. The sample prepared with nitrate as the starting material maintained high thermal stability and catalytic performance in the range of 400°C to 450°C, but CO conversion decreased below 350°C. Catalytic performance of the sample prepared with sulfate and chloride as the starting materials was poor, ranging from 200°C to 450°C.     

Role of metal Cu species on methyl laurate catalytic hydrogenation to oxygen-containing compounds

The Cu/γ-Al₂O₃ catalysts with different Cu loadings were prepared by impregnation method. The physicochemical properties of these Cu/γ-Al₂O₃ catalysts were characterized by H₂-TPR, XRD, and in-situ XPS. The catalytic hydrogenation performances of methyl laurate over Cu/γ-Al₂O₃ catalysts were studied. The results show that the hydrogenation performances of methyl laurate on Cu/γ-Al₂O₃ catalyst are related to the dispersion, crystallite size, and content of the active component Cu⁰. The 10CA catalyst has the best hydrogenation performances for methyl laurate to produce C₁₂ alcohol. At 300 °C, the conversion of methyl laurate and the selectivity of C₁₂ alcohol are 55.6% and 30.4%, respectively.     

CuY制备方法对其催化甲醇氧化羰基化活性中心的影响

以Cu(NO₃)₂为铜源,以NaY和HY分子筛为载体,通过溶液离子交换法和等体积浸渍法制备了不同的无氯CuY催化剂,并进行了气相甲醇氧化羰基化催化活性研究。通过浸渍法制备的催化剂Cu含量为10%,而以NaY和铜氨溶液离子交换制备的催化剂Cu含量只有6.3%,但其催化活性和选择性均较好。通过催化剂的Cu元素分析、低温氮吸附-脱附、XRD、H₂-TPR、XPS和TPD等表征表明,溶液离子交换法制备的催化剂,Cu物种以离子的形式高度分散于分子筛骨架结构中,较好地保持了分子筛晶体结构,并对甲醇有较强的吸附能力,催化活性较高,而将等体积浸渍Cu(NO₃)₂溶液后的HY或NaY分子筛,在400 ℃焙烧过程中,发生了固体离子交换反应,形成了连接于分子筛骨架的Cu²⁺,但以HY为载体更容易进行固体离子交换,未交换的铜物种以CuO的形式分散到分子筛表面。在600 ℃高温活化中,催化剂中Cu²⁺可部分还原为活性物质Cu⁺,但以NaY和铜氨溶液离子交换制备的催化剂Cu²⁺自还原能力最大。     

Mesoporous Mn promoted Co3O4 oxides as an efficient and stable catalyst for low temperature oxidation of CO

Mesoporous Mn-doped Co₃O₄ catalysts were successfully prepared via a dry soft reactive grinding method based on solid state reaction, and their catalytic performances on CO oxidation were evaluated at a high space velocity of 49,500 mL g⁻¹ h⁻¹. A significant promoted effect was observed once the atomic ratios of Mn/(Co+Mn) were lower than 10%, for instance, the temperature for 50% conversion decreased to about −60 °C, showing superior catalytic performance compared to the single metal oxide. Especially, the Mn-promoted Co₃O₄ catalyst with a Mn/(Co+Mn) molar ratio of 10% could convert 100% CO after 3000 min of time-on-steam without any deactivation at room temperature. As prepared catalysts were characterized by XRD, N₂-adsorption/desorption, TEM, H₂-TPR, O₂-TPD and CO-titration analysis. The significant enhancement of performance for oxidation of CO over Mn-Co-O mixed oxides was associated with the high active oxygen species concentrations formed during the pretreatment in O₂ atmosphere.     

载体H+含量对CuY甲醇氧化羰基化反应性能影响

通过过量浸渍Cu(NO_3)_2溶液于Y分子筛载体上,制备出Cu负载量为6.4%的CuY催化剂,考察了甲醇氧化羰基化反应的催化性能,并采用X射线衍射(XRD)、H2程序升温还原(H2-TPR)、透射电子显微镜(TEM)和NH3程序升温脱附(NH3-TPD)等手段对催化剂表面微观结构进行了表征。研究表明,随Y分子筛载体H+含量的增加,可使更多Cu物种落位于分子筛微孔笼结构中,且高度分散,而笼内未交换的Na+能进一步促进铜物种更多落位于载体超笼结构中,形成更多甲醇氧化羰基化反应的Cu+活性中心。同时随铜物种引入,催化剂中产生了明显的中强酸,酸量随落位于载体笼结构中的Cu物种的增加而增加,催化剂总酸量随之增加,导致甲醇氧化羰基化产物分布发生改变,碳酸二甲酯(DMC)选择性明显降低。对比等体积浸渍法制备的92.3%的高DMC选择性CuY催化剂,以不含H+的NaY分子筛为载体,过量浸渍法制备的CuY催化剂酸量少、Cu物种活性中心多,在保持82.4%的高DMC选择性时,其DMC的时空收率(STY)也高达109.1mg·g~(-1)·h-1。     

铜物种对Cu/Fe2O3水煤气变换反应催化剂性能的影响

采用共沉淀法制备了系列铜负载量不同的Cu/Fe₂O₃水煤气变换(WGS)催化剂,并考察了铜负载量对催化剂结构和水煤气变换反应性能的影响. 结果表明,Cu/Fe₂O₃催化剂呈现出良好的水煤气反应性能,当CuO质量分数为20%时,催化剂的WGS性能最优,250 ℃时CO转化率高达97.2%,同时热稳定性也最好. 运用X射线粉末衍射(XRD)、N₂物理吸脱附和H₂程序升温还原(H₂-TPR)等手段对Cu/Fe₂O₃催化剂的物相、织构特征及还原性能进行了表征,结果表明,CuFe₂O₄物种的存在极大地改善了催化剂的还原性能和WGS反应活性. 这是由于CuFe₂O₄特殊的尖晶石结构有利于Cu微晶的稳定;同时,CuFe₂O₄在低温下即被还原为单质铜,有利于促进催化剂体系中电子的转移. 此外,通过(NH₄)₂CO₃溶液处理,研究了独立相CuO对Cu/Fe₂O₃催化剂WGS反应性能的影响,结果发现,独立相CuO的存在,有利于H原子在各组分传递,从而促进催化剂的CuFe₂O₄的还原,改善Cu/Fe₂O₃催化剂的WGS反应性能.     

Ce-Cu-Co/CNTs催化剂催化合成气制低碳醇及乙醇的研究

采用共浸渍法制备了不同Ce含量的Ce-Cu-Co/CNTs 催化剂, 考察了其在合成气制低碳醇反应中的催化性能, 借助X射线衍射(XRD)、程序升温还原(H₂-TPR)、N₂吸脱附实验(BET)、透射电镜(TEM)和CO程序升温脱附(CO-TPD)对这些催化剂进行了表征. 结果表明, 当Ce的质量分数为3%时, 低碳醇的时空收率和选择性达到最高, 分别为696.4 mg·g^-1·h^-1和59.7%, 其中乙醇占总醇的46.8%, 适量Ce的添加能提高Cu物种在催化剂上的分散度和催化剂的还原性能, 能显著地增加催化剂吸附CO的能力, 促进合成醇活性位的形成, 进而明显提高催化剂的活性和总醇的选择性. 研究表明, 将具有高活性和高碳链增长能力的CuCo基催化剂与碳纳米管的限域效应结合, 可实现缩窄产物分布、大幅度提高乙醇选择性的目的.     

CO2加氢合成二甲醚的催化剂的制备

先采用均匀沉淀法制备出CuO—ZnO催化剂,然后以CuO—ZnO催化剂作为晶核采用水热合成法制备出CuO—ZnO／HZSM-5（氢型ZSM-5分子筛）复合催化剂．利用X射线衍射和氨程序升温脱附手段对复合催化剂进行表征,并应用于CO2催化加氢合成二甲醚的反应．研究结果表明,在相同的反应条件下,这种CuO—ZnO／HZSM-5复合催化剂与采用物理混合法制备出的复合催化剂相比具有更好的催化效果,不但提高了CO2的转化率、二甲醚的选择性以及二甲醚和甲醇的总选择性,同时还改善了催化剂的稳定性．     

焙烧温度对Pd-Cu/凹凸棒土CO常温催化氧化性能的影响

以凹凸棒土(APT)作载体,采用等体积浸渍法制备了Pd-Cu/APT催化剂,以CO氧化为探针反应,在连续流动微反装置上,考察了焙烧温度对催化剂CO常温催化氧化性能的影响。通过N2-物理吸附、XRD、TG、FT-IR和H2-TPR等手段对催化剂的结构和性质进行了表征。结果表明,随焙烧温度升高,Pd-Cu/APT中载体逐步脱水,进而引起催化剂结构和织构变化,其中,Cu物种由Cu(OH)Cl逐渐向CuO转变,同时,高分散的Pd物种与Cu物种间相互作用先增强后减弱。经300℃焙烧的催化剂比表面积大,Cu物种以Cu(OH)Cl形式存在,且具有良好的分散状态,与Pd物种之间产生较强的相互作用,显著提高了其还原性能。在空速6 000 h-1、CO体积分数0.5%、水蒸气体积分数3.3%的反应条件下,常温可将CO完全转化800 min以上。焙烧温度高于或低于300℃均引起CO常温催化氧化性能的下降。     

ZrO_2负载Pt催化巴豆醛选择性加氢

以高比表面积ZrO2为载体,采用浸渍法制备了负载型Pt催化剂,应用于常压下气相巴豆醛加氢反应,考察了Pt负载量和H2还原温度等对巴豆醛选择性加氢性能的影响.实验结果表明,Pt负载量(质量分数)为3%的3Pt/ZrO2催化剂经500℃还原后,具有较高的巴豆醛选择性加氢性能:巴豆醛转化率为27%,巴豆醇的选择性为55%.X射线粉末衍射(XRD)分析,CO化学吸附,NH3程序升温脱附(NH3-TPD)表征结果表明Pt/ZrO2催化剂上Lewis强酸中心和适宜的Pt颗粒(约为8nm)有利于巴豆醛选择性加氢生成巴豆醇.     

Isolated zinc in mordenite stabilizing carbonylation of dimethyl ether to methyl acetate

Mordenite with the isolated zinc ions enhanced the catalytic performance for carbonylation of dimethyl ether to methyl acetate. The addition of Zn affected the acid properties of the catalysts, further changed the rate of coke deposition.     

CO Oxidation on Cu/MgO-SiO2 Sol-Gel Derived Catalysts

Sol-gel Cu//MgOSiO₂ catalysts were prepared gelling tetraethoxysilane (TEOS), magnesium ethoxide and copper acetylacetonate at pH 3 and pH 9. The catalysts shown specific surface areas ca. 500 m²/g and 140 m²/g for pH 9 and pH 3 preparations respectively. Si(OH) and Si(OH)₂ hydroxy groups were observed by MAS-RMN spectroscopy in both preparations. CO₂-TPD and NH₃-TPD desorption thermograms showed that acid and basic sites were formed on the catalysts surface. It has been found that the catalysts having the highest density of basic sites were the catalysts showing the highest activity for the CO oxidation. It is proposed that the catalytic activity depends of the relative Cu⁼¹/Cu⁼² stability given by the support acidity.