High power Nd:YAG slab laser sidepumped by diode laser array

ＨｉｇｈｐｏｗｅｒＮｄ：ＹＡＧｓｌａｂｌａｓｅｒｓｉｄｅｐｕｍｐｅｄｂｙｄｉｏｄｅｌａｓｅｒａｒｒａｙＣＨＥＮＹｏｕｍｉｎｇ；ＺＨＯＵＦｕｚｈｅｎｇ；ＨＵＷｅｎｔａｏ；ＬＩＺｈｉｓｈｅｎ；ＹＡＮＧＸｉａｎｇｃｈｕｎ；ＷａｎｇＺｈｉｊｉａｎｇ（Ｓｈａｎ...     

Highly efficient phase locking of four diode pumped Nd:YAG laser beams

We describe the mutual phase-locking of four Nd:YAG beams longitudinally end-pumped by four fiber-coupled diode lasers. Mutual phase-locking is performed by two types of diffractive components located inside a telescopic Fabry–Perot resonator. The control of the phase-locking is shown and the different spatial eigenmodes connected with the pumping geometry in the resonator are theoretically and experimentally studied. 1.2 W is obtained in a single mode stable pattern with 30% optical-to-optical conversion efficiency in the continuous wave regime.     

Relative performance of a 1.06 μm laser with various Nd doped crystals

Laser emission at 1.06 μm has been observed from Nd: doped YAG, KGW and SGGM crystals pumped by a linear Xe-gas filled flashlamp in the input energy range of 1–25 J. The intrinsic slope efficiency has been determined to be 8.84%, 2.25% and 1.25% from Nd: KGW (Nd: 3% atomic), Nd: YAG (Nd: 1.0% atomic) and Nd: SGGM (Nd: 4% atomic), respectively.     

Nd:LuYAG混晶1123 nm被动调Q激光器

文章报道了一个二极管激光抽运的1123 nm被动调Q激光器. 激光晶体为混晶Nd:LuYAG, 饱和吸收体选为Cr⁴⁺:YAG晶体. 在连续运转情况下, 最高输出功率为2.77 W, 对应的光-光转换效率为29.53%. 调Q运转时, 在9.38 W吸收抽运功率下, 最高输出功率为0.94 W. 脉冲宽度整体在105 ns左右. 在最高吸收抽运功率下, 1123 nm激光的输出重复频率为9.40 kHz, 对应的单脉冲能量可达100 μJ, 高于目前报道的单晶Nd:YAG 1123 nm单脉冲能量, 证明其在能量存储方面较单晶Nd:YAG更具优势. 另外, 据我们所知, 这是关于混晶Nd:LuYAG 1123 nm输出的首次报道.     

A Nd: YAG laser with a flat-top beam profile and constant divergence

An active resonator designed especially for Nd: YAG lasers is proposed. The expected performance of this resonator is the generation of a laser beam with a flat-topped distribution and a divergence invariant under the thermal lensing effect, such that it could be applied to surface treatment without special optical or mechanical elements. The beam quality and efficiency of such a resonator are presented and discussed in comparison with a parallel-plane resonator as adopted by most industrial Nd: YAG lasers.     

Mathematical modelling of an Nd: YAG laser: peak power and pulse width

In a previous paper, the author presented an empirically derived mathematical model of a pulse pumped laser which allowed calculation of the output energy from the laser—from the mirrors-only resonator to the fully assembled Q-switched state. In this paper the model is developed further by deriving an expression for the peak output power. New coupling and loss time constant are stated. The validity of the model is demonstrated by the ability of calculate the laser parameters from a measured pulse shape, knowing the rod dimensions and the pump energy at which the pulse was measured.     

An investigation on laser-diode-array pumped Nd: glass slab laser

Ａｎｉｎｖｅｓｔｉｇａｔｉｏｎｏｎｌａｓｅｒ－ｄｉｏｄｅ－ａｒｒａｙｐｕｍｐｅｄＮｄ：ｇｌａｓｓｓｌａｂｌａｓｅｒ￥ＨＵＷｅｎｔａｏ；ＺＨＯＵＦｕｚｈｅｎｇ；ＣＨＥＮＹｏｕｍｉｎｇ；ＪＩＡＮＧＺｈｏｎｇｈｏｎｇ（ＳｈａｎｇｈａｉＩｎｓｔｉｔｕｔｅｏｆ...     

Transmission properties of all-silica fibres for high-power Nd:YAG lasers

The transmission properties of two different types of all-silica fibres, step index and graded-index fibres, are investigated using a multimode high-power cw Nd:YAG rod laser. The reflections from the fibre surface back into the laser cavity affect the laser power and the beam parameters, waist diameter and divergence. A set-up for simultaneously measuring these values in front of and behind a fibre is presented. The maximum laser power transmitted by fibres is dependent upon the beam parameters, the fibre design and the surface conditions. An upper limit for the maximum divergence which can be coupled into a fibre with a certain numerical aperture without loss is given. The beam parameters behind the fibre, related to the input parameters, are presented.     

Experimental study of high-power pulse side-pumped Nd:YAG laser

The paper reports on the characterization of a compact and simple side-pumped 0.538 J×100 Hz pulse Nd:YAG laser. A side-pumping configuration with 100 laser diode bars is used in the laser head. We also experimentally studied the laser performance of the diode-pumped Nd:YAG laser head in the free running and Q-switched operation under different repetition rates.     

Solar pumped Nd:YAG laser

We report the high efficiency of solar pumped laser. The sunlight is concentrated by the concentrator system, which is composed by the Fresnel lens and the cone-channel condenser. The power density of sunlight concentrated by the concentrator system surpasses the lasing threshold for pumping laser. In the experiment, the sunlight concentrated is coupled into the conical chamber pumping Nd:YAG laser media. Laser output of 3.5 W has been achieved; the collect efficiency is 3.5 W/m². The conversion efficiency is 1.0% from solar power into laser, and the slope efficiency is achieved 1.86%.     

CW mode locked Nd:YVO4 laser pumped by 20-W laser diode bar

The efficient cw mode locking (cw-ML) regime was demonstrated in Nd:YVO₄ laser by means of saturable absorber mirror (SAM). The 0.3-at.% Nd³⁺ doped 10-mm-long YVO₄ crystal end pumped by 20-W diode module with a beam shaper was applied as a gain medium located in the close vicinity to the rear flat mirror of the first arm of Z-type resonator of 316 cm total length with two curved mirrors of 100-cm curvature radii. The SAM of 2%-saturable absorptance and saturation fluence of 50 μJ/cm² was mounted at the opposite end of a resonator. The developed “dynamically stable” cavity design mitigates detrimental role of thermal aberration in gain medium, enforcing clean perfect mode locking even for the highest pump densities. The cw-ML pulses with 47.5 MHz repetition rate and pulse durations in the range of 15–20 ps were observed for a wide range of pump powers and output coupler losses. In the best case, for 32% of output coupler transmission, up to 6.2 W of average power with near 35% slope efficiency was achieved. The thresholds for Q-switched ML, cw-ML regimes were 2.67 W and 6.13 W of pump power, respectively. For the maximum pump power of 20 W we obtained 133 nJ of pulse energy with 16-ps pulse duration, resulting in a peak power higher than 8 kW. The threshold energy density at SAM giving the QML regime was estimated to be about 30 μJ/cm², threshold of cw-ML regime was 220 μJ/cm².     

An automatically controlled Nd:YAG laser with variable pulse width

The development of a high-energy, pulsed Nd:YAG laser system for materials-processing and medical applications is reported here. A variable pulse width in the range of 0.3–10 ms and a variable pulse repetition rate up to 50 pps are provided. An automatic operation system using a microprocessor-based driver/ controller enables safe operation of the laser system and automatic material processing when integrated in a laser/robot system.     

100W二极管泵浦Nd:YAG薄片激光器

报道了一台高效率二极管泵浦Nd:YAG薄片激光器,采用高效均匀泵浦耦合技术,在峰值功率1.008kW,占空比25％, 电-光效率大于45%的二极管激光阵列泵浦下,用一块1mm厚的Nd:YAG薄片激光介质,获得了峰值功率404W,平均功率101W的准连续激光输出,光-光效率达到40%,电-光效率超过18%。     

Laser diode-array pumped Nd:YAlO_3 CW laser at 1079.5nm and 1341.4nm

Two key problems,spectral matching and spatial overlap between pumpingbeam and the laser mode in the active material,of diode-laser-arrays(LD)end-pumped solid-state laser have been discussed.Initial experimental results were given for LD end-pumpedTEM_(00) CW Nd:YAlO_3 laser at the wavelength of 1079.5nm and 1341.4nm.The outputpower at 1079.5nm is 24.4mW with 14.5％ slope efficiency,and the output power is 1.2mW at 1341.4nm.     

Investigation of a Cr: YAG passive Q-switch in CW pumped Nd: YAG lasers

This work describes the experimental results obtained on the Cr⁴⁺:YAG crystal used as a passive Q-switch in Nd: YAG lasers. In addition, the combination of a Cr⁴⁺: YAG passive Q-switch with an acousto-optical Q-switch operating simultaneously in one cavity was investigated. More than 180 W average output in the passive Q-switched mode was obtained with the C⁴⁺: YAG crystal. The pulse-to-pulse stability was better than 1%. A mode selection occurred when the laser system operated near threshold.     

Nd:YAG laser delivery system utilizing GRIN rod lenses as focusing-collimating optics

A sequential electromechanical system capable of delivering the radiation coming from a medium power Nd:YAG laser to an array of multimode optical fibres is presented. The system utilizes GRIN-rod microlenses as focusing-collimating optics. A focusing unit positioned at the fibre distal-end, which can work in two different configurations, has also been designed and constructed.     

Reduction of beam divergence of a thermal lensing insensitive Nd:YAG laser

In a previous paper we proposed an active resonator designed especially for Nd:YAG lasers. The beam generated by this resonator had a flat-top beam profile and a divergence that was insensitive to the thermal lensing effect. The beam generated by this resonator was, however, too divergent to be focused into a fibre. With the help of numerical simulations, we have found a way to reduce this divergence, and to render the far-field of the laser beam fine enough to be coupled into a fibre with 600 μm core and NA = 0.2.     

Output characteristics of a flashlamp pumped Nd:YAG laser at 1444 nm

An investigation of the output characteristics of Nd:YAG lasers operating at a wavelength of 1444 nm using a Xe-flashlamp of 450 Torr, a Xe-flashlamp of 700 Torr, and a Kr-flashlamp of 700 Torr is reported. The highest electrical-to-optical conversion efficiency of 1.83% was attained using the Kr-flashlamp of 700 Torr with a repetition rate of 20 Hz, a pumping pulse width of 144 μs, and an input energy of 31.7 J. The investigation concluded that output energy depends on the temperature of cooling water. The results showed a 3% decrease in output energy at an input energy of 31.7 J as the temperature of cooling water was increased from 23 to 38 °C.     

高功率四波长Nd:YAG激光实验

四波长Nd：YAG激光实验是利用非线性晶体BBO，通过倍频、混频和二次倍频等激光变频技术，分别获取了4个波段相干辐射光，本文介绍了各波长相干辐射光的获取方法及其时空特性的测量。     

Investigation into absorption of the incident laser beam during Nd:YAG laser processing of metals

Laser materials processing is highly affected by the existence of surface plasma. The absorption of surface plasma during drilling alters the power intensity distribution of the incident laser beam across the irradiated spot. The present study is carried out to measure the electron number density and temperature using a Langmuir probe while a mathematical formulation is conducted for the absorption coefficients due to electron-ion, electron-neutral atom collisions, inverse Bremsstrahlung, and photoionization processes. Consequently, a computer program is developed to compute the relevant absorption coefficients as well as the overall absorption coefficient. The laser power intensity distribution before and after the plasma absorption is computed at a plane 2.6 mm above the workpiece surface. It is found that 13% of the reduction occurs in the incident laser output power intensity at this plane in the plasma.