STANDARDS FOR UV INSTRUMENTS AND RISK OF EXISTING DEVICES

Abstract— Different methods for measurements of UV-radiation of various light sources are quantitatively compared: direct measurements, based on detectors of known responsivity, as well as indirect measurements, based on a spectral irradiance calibration. The optical arrangement of an accurate spectroradiometric equipment, and the structure and parameters for a new type of cosine corrected detector for the measurement of actinic radiation are described, too. The measurements of actinic radiation with commercial devices are affected by great relative errors.
A standard for natural irradiance will allow a comparison of weighted irradiances and threshold irradiations with natural insolation and with artificial UV radiation. The risk of existing irradiation apparatuses will be calculable by this comparison.     

Microstructures in aqueous solutions of a polyoxyethylene trisiloxane surfactant and a cosurfactant studied by SANS and NMR self-diffusion

Microemulsion samples of a polyoxyethylene trisiloxane surfactant, water, and 1-decanol are investigated using pulsed field gradient NMR and small-angle neutron scattering (SANS) to determine the solution structure. The surfactant/decanol weight ratio has been kept constant at values of 10:1, 8:1, and 6:1 under variation of water content. The temperature was 32 degrees C for the measurement series at the weight ratio of 10:1 to avoid phase separation at high water content. Also, aqueous surfactant solution samples have been investigated as a function of composition and temperature. Water-rich samples consist of micelles that are close to spherical at very low surfactant concentration and grow into anisometric, that is, oblate formed aggregates, at higher surfactant (or surfactant and decanol) concentration. The aggregates grow with increasing temperature, most probably due to dehydration of the hydrophilic groups. In a concentration range around 50 wt % water, the systems form bicontinuous structures. SANS data are used to estimate surfactant film properties using a model developed for interpretation of neutron scattering data from related systems.     

The surface and solution properties of dihexadecyl dimethylammonium bromide

The surface adsorption behavior and solution aggregate microstructure of the dichain cationic surfactant dihexadecyl dimethylammonium bromide (DHDAB) have been studied using small angle neutron scattering (SANS), light scattering, neutron reflectivity (NR), and surface tension (ST). Using a combination of surface tension and neutron reflectivity, the DHDAB equilibrium surface excess at saturation adsorption has been measured as 2.60 +/- 0.05 x 10 (-10) mol.cm (-2). The values obtained by both methods are in good agreement and are consistent with the values reported for other dialkyl chain surfactants. The critical aggregation concentration (CAC) values obtained from both methods (NR and ST) are also in good agreement, with a mean value for the CAC of 4 +/- 2 x 10 (-5) M. The surface equilibrium is relatively slow, and this is attributed to monomer depletion in the near surface region, as a consequence of the long monomer residence times in the surfactant aggregates. The solution aggregate morphology has been determined using a combination of SANS, dynamic light scattering (DLS), cryogenic transmission electron microscopy (CryoTEM), and ultrasmall angle neutron scattering (USANS). Within the concentration range 1.5-80 mM, the aggregates are in the form of bilamellar vesicles with a lamellar " d-spacing" of the order of 900 A. The vesicles are relatively polydisperse with a particle size in the range 2000-4000 A. Above 80 mM, the bilamellar vesicles coexist with an additional L beta lamellar phase.     

Small angle neutron scattering study of tetramethylurea solutions

The results of small-angle neutron scattering(SANS) carried out on aqueous and CS₂ solutions of tetramethylurea(TMU) are compared. It is shown that the SANS data indicate the formation of TMU-TMU dimers in both solutions.     

Micellar characteristics of diblock polyacrylate-polyethylene oxide copolymers in aqueous media

The formation and structural features of micelles from low molecular weight diblock copolymers of poly(methylmethacrylate-b-ethylene oxide) PMMA-PEO (varying in total molecular weight) and poly(butylmethacrylate-b-ethylene oxide) PBMA-PEO in water, aqueous NaCl and urea solutions were examined by surface tension, dye spectral, cloud point, viscosity and small angle neutron scattering (SANS) measurements. The increasing concentrations of NaCl reduce the onset concentration of micellization and phase separation, while urea has reverse effect. The analysis of the SANS curves revealed the presence of prolate ellipsoidal micelles in diblock copolymers at various experimental concentrations and temperatures studied. The effect of temperature, NaCl and urea on the neutron scattering profiles are more or less the same which is well supported by viscosity and surface tension measurements. The diblock copolymers form spherical micelles of aggregation number in the range of 522-664. The micelles are very temperature stable.     

Dynamic properties of microemulsions modified with homopolymers and diblock copolymers: the determination of bending moduli and renormalization effects

The properties of bicontinuous microemulsions, consisting of water, oil, and a surfactant, can be modified by the addition of diblock copolymers (boosting effect) and homopolymers (inverse boosting effect) or a combination of both. Here, the influence of the addition of homopolymers (PEP(X) and PEO(X), X=5k or 10k molecular weight) on the dynamics of the surfactant layer is studied with neutron spin echo spectroscopy (NSE). Combining the results with the previous findings for diblock copolymers allows for a better separation of viscosity and bending modulus effects. With the addition of homopolymers, a significant increase of the relaxation rate compared to the pure microemulsion has been observed. The influence on the bending rigidity kappa is measured with NSE experiments. Homopolymer addition reduces kappa by up to Deltakappa approximately -0.5k(B)T, whereas the diblock copolymer yields an increase of kappa by approximately 0.3k(B)T. Comparison of the bending moduli that are obtained by analysis of the dynamics to those obtained from small angle neutron scattering (SANS) sheds light on the different renormalization length scales for NSE and SANS. Variation of the surfactant concentration at otherwise constant conditions of homopolymer or diblock-copolymer concentration shows that NSE results are leading to the pure bending rigidity, while the renormalized one is measured with SANS.     

Small-angle X-ray and neutron scattering studies of the morphology of ionomers

Preliminary small-angle neutron scattering (SANS) studies have been made of different ionomers in the dry state and after saturation with water. Scattering from the dry samples arises from differences in the neutron scattering cross sections of the ionic and nonionic units in the polymer. The SANS technique is complementary to previous small-angle x-ray scattering (SAXS) studies since the SANS contrast differences are generally quite different than those for SAXS. A quantitative comparison is made of SANS and SAXS intensities for a dry cesium salt of an ethylene-methacrylic acid (E-MAA) copolymer. For water-saturated samples the technique of isotopic replacement can be used in conjunction with SANS since saturation can be effected with either H₂O or D₂O. In this case information about the chemical composition of the phases is obtained from an analysis of the intensity ratio I/I. Results are consistent with the presence of a separate phase containing water molecules and ions in a matrix of the nonionic units. A Guinier analysis gives a radius of gyration of 17 Å for a water-saturated cesium salt of an E-MAA copolymer.     

A small angle neutron scattering study of the conformation of a side chain liquid crystal poly(methacrylate) in the smectic C phase

The conformation of the backbone in the side chain liquid crystal polymer poly\[ omega (4-methoxybiphenyl-4-yloxy)butyl methacrylate] has been studied in the smectic C and nematic phases. Small angle neutron scattering experiments were performed on mixtures of molecules with perdeuteriated backbones and unlabelled molecules. The polymer is found to adopt an oblate conformation in the smectic C phase. The components of the radius of gyration parallel and perpendicular to the director are determined as a function of temperature from Guinier plots of the SANS data. The radii of gyration do not vary across the smectic phase and are found to be Rg,||=(27+/-1)A, Rg, =(42+/-1)A. These results are compared with recent SANS results for other side chain liquid crystal polymers.     

Nematic and columnar ordering of a PEG-peptide conjugate in aqueous solution

The self-assembly in aqueous solution of a PEG-peptide conjugate is studied by spectroscopy, electron microscopy, rheology and small-angle X-ray and neutron scattering (SAXS and SANS). The peptide fragment, FFKLVFF is based on fragment KLVFF of the amyloid beta-peptide, Abeta(16-20), extended by two hydrophobic phenylalanine units. This is conjugated to PEG which confers water solubility and leads to distinct self-assembled structures. Small-angle scattering reveals the formation of cylindrical fibrils comprising a peptide core and PEG corona. This constrained structure leads to a model parallel beta-sheet self-assembled structure with a radial arrangement of beta sheets. On increasing concentration, successively nematic and hexagonal columnar phases are formed. The flow-induced alignment of both structures was studied in situ by SANS using a Couette cell. Shear-induced alignment is responsible for the shear thinning behaviour observed by dynamic shear rheometry. Incomplete recovery of moduli after cessation of shear is consistent with the observation from SANS of retained orientation in the sample.     

Micro- and mesoscopic structure of poly(vinyl alcohol) gels determined by neutron and light scattering

We studied the structure of poly(vinyl alcohol) (PVA) gels formed in mixtures of dimethyl sulfoxide (DMSO) and water using several scattering techniques such as wide-angle neutron scattering (WANS), small-angle neutron scattering (SANS), ultra-small-angle neutron scattering (U-SANS) and light scattering (LS) to cover a very wide Q range from 10^-4 to 10 Å^-1. The WANS measurements have revealed that the cross-linking points of the gels are crystallites, and the size and its distribution have been evaluated by the SANS measurements. The SANS results have also shown that the structure observed in the low Q range below 10^-2 Å^-1 is dominated by a liquid–liquid-phase separation. The early stage of the phase separation has been studied in detail using the time-resolved LS technique, while the late stage has been investigated by the U-SANS technique because the LS measurements cannot access the opaque samples. On the basis of the results, we present a quantitative sketch of the structure of the PVA gel.     

Small-Angle Neutron Scattering Studies of Polymers: Selected Aspects

Small-angle neutron scattering (SANS) studies of polymers are no longer a rarity in polymer science. It is now widely appreciated that SANS can provide unique data which provide greater insight into polymer structural properties than otherwise obtainable. Nonetheless, the costs of the apparatus and special efforts that have to be taken to prepare necessary deuterated polymers mean that such experiments have to be designed with care to ensure that unambiguous data are obtained. There are now in existence several reviews on various aspects [1–4] of SANS studies of polymers; attention in this review is focused on multiphase polymer systems. However, newer aspects of SANS studies on homopolymers will also be discussed, and we begin by a necessarily brief survey of the relevant theoretical expressions.     

Gelation Dynamics and Mechanism(s) in Stereoregular Poly(Methyl Methacrylate)s

Chain conformation and gel structure of syndiotactic PMMA thermoreversible gels have been investigated using small angle neutron scattering (SANS). A double helix model for the chain conformation is proposed alongside a gel network model where the fibrils are formed by the proposed double helix and the junctions by the aggregation of 3 double helices. Preliminary results, also obtained by SANS, for stereocomplex gels prepared in bromobenzene are presented.     

SAXS and SANS studies of polymer colloids

The analysis of latex particles by small-angle scattering (small-angle X-ray scattering, SAXS; small-angle neutron scattering, SANS) is reviewed. Small-angle scattering techniques give information on the radial structure of the particles as well as on their spatial correlation. Recent progress in instrumentation allows to extend SANS and SAXS to the q-range of light scattering. Moreover, contrast variation employed in SANS and SAXS studies may lead to an unambiguous determination of the radial scattering length density of the particles in situ, i.e. in suspension. Hence, these techniques are highly valuable for a comprehensive analysis of polymer colloids as shown by the examples discussed herein.     

Calcium induced volume transition in polyelectrolyte gels

The osmotic properties and the small angle neutron scattering (SANS) behaviour of fully neutralized sodium polyacrylate gels are investigated in the presence of calcium ions. Analysis of the SANS response displays three characteristic length scales, two of which are of thermodynamic origin, while the third, associated with the frozen-in structural inhomogeneities, is static. The SANS results are consistent with direct osmotic observations which indicate that the thermodynamic properties cannot be adequately described by a single correlation length. The concentration dependence of the osmotic pressure displays a power law behaviour with an exponent that decreases with increasing calcium concentration.     

Small angle neutron scattering measurements of synthetic polymer dispersions in matrix-assisted laser desorption/ionization matrixes

Small angle neutron scattering (SANS) is used to measure the size and the dispersion of synthetic polymers in matrix-assisted laser desorption/ionization (MALDI) matrixes. Deuterated polystyrene (DPS) and dithranol in tetrahydrofuran were deposited by electrospray onto a substrate for small angle neutron scattering (SANS) measurements. DPS with 6050 and 27,000 g mol(-1) molecular masses were prepared at mass fractions between 0.2 and 6%. All samples contained large aggregates of DPS with characteristic sizes >200 A that represent hundreds of aggregated chains. Samples of mass fraction 1% DPS (6050 g mol(-1)) in 2,5-dihydroxybenzoic acid, all-trans-retinoic acid, and sinapinic acid also have large zero angle scattering characteristic of large aggregates. The morphological trend obtained from the SANS measurements of the DPS aggregate size in the four matrixes is dithranol > 2,5-dihydroxybenzoic acid > all-trans-retinoic acid > sinapinic acid. These measurements indicate that DPS in dithranol exhibits the most strong phase separation, while DPS in sinapinic acid shows considerable domain mixing. All of these matrixes produce MALDI signal strength under appropriate conditions, suggesting that strong phase separation does not diminish the signal-to-noise ratio. DPS (188,000 g mol(-1)) in biphenyl was used as a model system of a matrix that can be either crystalline or amorphous. SANS data shows that above the biphenyl melting point, a conventional solution is formed that has molecularly dispersed polymers. Upon crystallization, there is strong aggregation of the DPS into large domains. Therefore, the crystalline matrixes commonly used in MALDI measurements probably cause large aggregations of polymers to be present during the MALDI process.     

Structures of Fibrous Supramolecular Assemblies Constructed by Amino Acid Surfactants: Investigation by AFM, SANS, and SAXS

Aqueous gel-like solutions of N-acyl-L-aspartic acids (C(n)Asp, n=14, 16, 18) and N-dodecanoyl-beta-alanine (C(12)Ala) were prepared at pH 5-6 at room temperature. Structures of supramolecular assemblies in the solutions were investigated by atomic force microscopy (AFM), small-angle neutron scattering (SANS), and small-angle X-ray scattering (SAXS). The cross-sectional radii, 22-30 ?, of helical, fibrous assemblies were obtained from analysis of SANS for 1% gel-like C(n)Asp solutions. Three Bragg spacings were observed in a SANS spectrum for a 6% C(16)Asp solution. C(n)Asp molecules are associated into the unit chain of a helical bilayer strand with a diameter of 50-60 ?. Unit chains where linear bilayers twist form a double strand with helical sense of approximately 650-? pitch. It was confirmed from AFM images that cylindrical fibers in a gel-like C(12)Ala solution had a circular cross-section. The SAXS spectrum showed characteristic Bragg spacings. Cylindrical C(12)Ala fibers consist of multilamellar layers of period approximately 34-?. The fibers are laterally organized with period 365-380 ?. Copyright 2000 Academic Press.     

In situ small-angle neutron scattering and rheological measurements of shear-induced gelation

The microscopic structure of shear-induced gels for a mixed solution of 2-hydroxyethyl cellulose and nanometer-size spherical droplets has been investigated by in situ small-angle neutron scattering (SANS) with a Couette geometry as a function of shear rate gamma. With increasing gamma, the viscosity increased rapidly at gamma approximately 4.0 s(-1), followed by a shear thinning. After cessation of shear, the system exhibited an extraordinarily large steady viscosity. This phenomenon was observed as a shear-induced sol-gel transition. Real-time SANS measurements showed an increase in the scattering intensity exclusively at low scattering angle region. However, neither orientation of polymer chains nor droplet deformation was detected and the SANS patterns remained isotropic irrespective of gamma. It took about a few days for the gel to recover its original sol state. A possible mechanism of gelation is proposed from the viewpoint of shear-induced percolation transition.     

Influence of a hydrophobic diol on the micellar transitions of Pluronic P85 in aqueous solution

Micellization behavior of an amphiphilic ethylene oxide-propylene oxide-ethylene oxide tri-block copolymer Pluronic P85 [(EO)(26)(PO)(39)-(EO)(26)] in aqueous solution and in the presence of a hydrophobic C(14)diol (also known as Surfynol104) was examined by physico-chemical methods such as viscometry, cloud point (CP) and scattering techniques viz. dynamic light scattering (DLS) and small angle neutron scattering (SANS). The addition of diol decreases the cloud point and gelation temperature of aqueous Pluronic P85 copolymer solution. DLS and SANS measurements of the polymer in aqueous solution indicated micellar growth and sphere to rod transition in the presence of diol. Surfynol 104 is a sparingly water soluble diol surfactant with a solubility of approximately 0.1 wt%. However, up on addition to Pluronic solution, diol gets incorporated in the block copolymer micelles and leads to structural transition of the micelles. An increase in the temperature and the presence of added sodium chloride in the solution further enhances this effect. The addition of hydrophobic C(14)diol increases the hydrodynamic size and aggregation numbers of the micellar system. The micellar parameters for the copolymer in the presence of C(14)diol are reported at different temperatures and added sodium chloride concentrations.     

Neutron scattering study of the structural change induced by photopolymerization of AOT/D2O/dodecyl acrylate inverse microemulsions

Small-angle and ultrasmall-angle neutron scattering (SANS/USANS) measurements were used to determine the structural changes induced by photopolymerization of AOT/D2O/(dodecyl acrylate) inverse microemulsion systems. Scattering profiles were collected for the initial microemulsions and the films resulting from photopolymerization of the oil phase. The SANS data for the microemulsions were modeled as spherical, core-shell droplets. Upon polymerization, the clear mircoemulsions formed opaque films. From the SANS/USANS data of the films, it was apparent that this morphology was not preserved upon polymerization; however, it was clearly observed that the formulation of the microemulsion had a large impact on the structure within the films. The Guinier region in the USANS data (2.5 x 10(-5) A(-1) < or = Q < or = 5.3 x 10(-3) A(-1)) from the films indicates that very large structures are formed. Simultaneously, a well-defined peak (0.15 A(-1) < or = Q < or = 0.25 A(-1)) in the SANS data indicates that there are also much smaller structures formed. It is proposed that the low-Q scattering arises from aggregation of the nanometer-size water droplets in the microemulsion to form droplets large enough to scatter visible light, while the peak in the high-Q region results from bilayered structures formed by the surfactant.