Preparation and thermal properties of chemically prepared nanoporous silica aerogels

This work focuses on the dependence preparation conditions—structure—physical properties of hydrophobic silica aerogels, all of them prepared under subcritical drying conditions (70 °C and 0.4 atm.), thus aiming at potential application as case insulation filling in heat pumps. The so prepared, millimeter scaled nano-porous hydrophobic silica aerogel granules were analyzed with standard electron microscope and atomic force microscopy, IR spectroscopy, UV/Vis spectroscopy, differential scanning calorimetry and thermal conductivity measurements. The physical properties of the aerogels were compared with commercial aerogel granules. A method for contact angle measurement of micro-droplets situated on the silica granules was proposed to quantify the level of their hydrophobicity.     

Effective preparation of crack-free silica aerogels via ambient drying

Effective ambient-drying techniques for synthesizing crack-free silica aerogel bulks from the industrial waterglass have been developed. Silica wet gels were obtained from aqueous colloidal silica sols prepared by ion-exchange of waterglass solution (4–10 wt% SiO₂). Crack-free monolithic silica aerogel disks (diameter of 22 mm and thickness of 7 mm) were produced via solvent exchange/surface modification of the wet gels using isopropanol/trimethylchlorosilane/n-Hexane solution, followed by ambient drying. The effects of the silica content in sol and the molar ratio of trimethylchlorosilane/pore water on the morphology and property of final aerogel products were also investigated. The porosity, density, and specific surface area of silica aerogels were in the range of 92–94%, 0.13–0.16 g/cm³, and ∼675 m²/g, respectively. The degree of springback during the ambient drying processing of modified silica gels was 94%.     

Synthesis of nanoporous silica aerogel by ambient pressure drying

A crack-free silica aerogel monolith was fabricated from a cheap water glass derived silicic acid solution by adding glycerol, which served as a drying control chemical additive (DCCA). The OH surfaces of the wet gel with glycerol were modified using a TMCS/n-hexane mixture followed by solvent exchange from water to n-hexane. The obtained surface modified wet gel was dried at 75 °C under ambient pressure. The addition of glycerol appears to give the wet gel a more homogeneous microstructure (larger pore size and uniform size distribution) as well as enhanced stiffness. However, glycerol also retards surface modification and solvent exchange. The aerogel synthesized with glycerol added to the silica sol maintained a relatively low bulk density compared with the aerogels aged in a mixed ethanol (EtOH)/TEOS solution. The reproducibility of aerogel production was further improved in the aerogel synthesized with glycerol added to the silica sol and aged in a 70%EtOH/30%TEOS solution.     

Ambient pressure drying: a successful approach for the preparation of silica and silica based mixed oxide aerogels

Silica aerogels have received much attention in recent years as it has got a wide range of properties like high surface area, low density, high porosity, low dielectric constant, low thermal conductivity. Recently to make aerogels for commercial application ambient pressure drying has been preferred and also a cheap precursor like sodium silicate has been employed as the starting material instead of the alkoxides. In this review, attention will be given to the synthesis adopted for the preparation of silica and silica based mixed oxide/composite aerogels through ambient pressure drying. The properties of the prepared aerogels are also discussed in detail.     

Preparation and characterization of silica aerogels from diatomite via ambient pressure drying

The silica aerogels were successfully fabricated under ambient pressure from diatomite. The influence of different dilution ratios of diatomite filtrate on physical properties of aerogels were studied. The microstructure, surface functional groups, thermal stability, morphology and mechanical properties of silica aerogels based on diatomite were investigated by BET adsorption, FT-IR, DTA-TG, FESEM, TEM, and nanoindentation methods. The results indicate that the filtrate diluted with distilled water in a proportion of 1: 2 could give silica aerogels in the largest size with highest transparency. The obtained aerogels with density of 0.122–0.203 g/m³ and specific surface area of 655.5–790.7 m²/g are crack free amorphous solids and exhibited a sponge-like structure. Moreover, the peak pore size resided at 9 nm. The initial aerogels were hydrophobic, when being heat-treated around 400°C, the aerogels were transformed into hydrophilic ones. The obtained aerogel has good mechanical properties.     

Study of the effect of organo-substituted trialkoxysilanes on the textural and structural properties of mesoporous silica

The effect of additives of organo-substituted trialkoxysilanes: (3-aminopropyl)triethoxysilane (APTES), (2-cyanoethyl)triethoxysilane (CNETES), and tris(trimethylsiloxy)silane (TTMSS) as cosources of silica on its textural and structural properties was studied. The influence of organo-substituted trialkoxysilane additives on the variation of porous structure parameters of mesoporous silica during the hydrothermal treatment was demonstrated. The synthesized mesoporous silica samples were characterized by low-temperature nitrogen adsorption, X-ray powder diffraction, scanning electron microscopy, thermal and elemental analysis, and Raman spectroscopy.     

Influence of supercritical drying fluids on structures and properties of low-density Cu-doped SiO2 composite aerogels

The Cu-doped SiO₂ composite aerogels were successfully prepared by sol–gel process and subsequently supercritical drying with ethanol and CO₂. The Cu-doped SiO₂ composite aerogels had porous texture, low density (<100 mg cm^?3) and high specific surface area (>800 m² g^?1), which were investigated by FESEM and nitrogen adsorption desorption porosimetry. The FTIR spectra of the aerogels showed that the ethanol-dried aerogels had been modified by ethyl while the corresponding CO₂-dried aerogels had more Si–OH groups. The phase structure and thermal stability were investigated by XRD and TGA, respectively. Due to the reducibility of ethanol, the copper was crystalline in ethanol-dried sample. The Cu-doped SiO₂ composite aerogels dried with supercritical ethanol had larger pore diameter and better thermal stability under 400 °C in comparison with CO₂-dried composite aerogels. The structures and properties of Cu-doped SiO₂ composite aerogels are obviously affected by supercritical drying conditions. The effect research could instruct the synthesis of different state of Cu in composite aerogels.     

Effect of the addition of a second phenol on the textural properties of carbon aerogels

Three carbon aerogels (AGC) were prepared using the sol–gel method from the polymerization of mixtures of resorcinol–catechol (RC), resorcinol-m-cresol, and resorcinol–phloroglucinol (RP). Cobalt acetate was used as polymerization catalyst. The porous texture and the morphology of carbon aerogels were characterized by nitrogen adsorption at 77 K, carbon dioxide at 273 K and scanning electron microscopy. Their structure and chemical surface were analyzed by means of X-ray diffraction and X-ray photoelectron spectroscopy. It was found that the addition of a second phenol influences the porosity of the material. The carbon aerogel prepared with m-cresol as a monomer presented constrictions at the entrance of the micropores and lower pore volume compared to that of RC and RP. This fact is possibly due to the presence of the methyl group. Moreover, this monomer favors the formation of carbon fibers.     

Catalytic properties of transition metal salts immobilized on nanoporous silica polyamine composites II: hydrogenation

The transition metal compounds Pd(OAc)₂, RhCl₃·4H₂O and RuCl₃ · nH₂O were adsorbed onto the nanoporous silica polyamine composite (SPC) particles (150–250 µm), WP‐1 [poly(ethyleneimine) on amorphous silica], BP‐1 [poly(allylamine) on amorphous silica], WP‐2 (WP‐1 modified with chloroacetic acid) and BP‐2 (BP‐1 modified with chloroacetic acid). Inductively coupled plasma‐atomic emission spectrometry analysis of the dried samples after digestion indicated metal loadings of 0.4–1.2 mmol g^?1 except for RhCl₃·4H₂O on BP‐2 which showed a metal loading of only 0.1 mmol g^?1. The metal loaded composites were then screened as hydrogenation catalysts for the reduction of 1‐octene, 1‐decene, 1‐hexene and 1, 3‐cyclohexadiene at a hydrogen pressure of 5 atm in the temperature range of 50–90 °C. All 12 combinations of SPC and transition metal compound proved active for the reduction of the terminal olefins, but isomerization to internal alkenes was competitive in all cases. Under these conditions, selective hydrogenation of 1,3‐cyclohexadiene to cyclohexene was observed with some of the catalysts. Turnover frequencies were estimated for the hydrogenation reactions based on the metal loading and were in some cases comparable to more conventional heterogeneous hydrogenation catalysts. Examination of the catalysts before and after reaction with X‐ray photoelectron spectroscopy and transmission electron microscopy revealed that, in the cases of Pd(OAc)₂ on WP‐2, BP‐1 and BP‐2, conversion of the surface‐ligand bound metal ions to metal nano‐particles occurs. This was not the case for Pd(OAc)₂ on WP‐1 or for RuCl₃ · nH₂O and RhCl₃· 4H₂O on all four composites. The overall results are discussed in terms of differences in metal ion coordination modes for the composite transition‐metal combinations. Suggested ligand interactions are supported by solid state CPMAS ¹³C NMR analyses and by analogy with previous structural investigations of metal binding modes on these composite materials. Copyright © 2011 John Wiley & Sons, Ltd.     

The effect of heat-treatment on the physico-chemical properties of silica aerogel prepared by sub-critical drying technique

Synthesis of transparent and crack-free monoliths of silica aerogel by sub-critical drying technique is reported in the present article. Silane ageing with 50% tetraethylorthosilicate:ethanol followed by solvent exchange using ethanol was adopted. The effect of heat-treatment on the textural and physical characteristics of silica aerogel was evaluated. The chosen composition resulted in a high surface area silica aerogel of 1,000 m² g⁻¹ and a pore volume of 1.4 cm³ g⁻¹ at room temperature. The aerogel heat-treated at 900 °C possessed a surface area of 450 m² g⁻¹ with a pore volume of 0.4 cm³ g⁻¹. The decrease in surface area and pore volume was associated with the sintering process. The present technique seems advantageous in preserving the high surface area of the material at high temperatures. The XRD studies showed that the amorphous nature of aerogel matrix was retained till 1,400 °C, beyond which it crystallized to phase pure crystoballite.     

Effect of 3-glycidoxypropyltrimethoxysilane precursor on the properties of ambient pressure dried silica aerogels

The effect of an organically modified precursor, 3-glycidoxypropyltrimethoxysilane in an ambient pressure process involving aging in silane solution for silica aerogels is presented. The effect of increasing trialkoxysilane/tetraalkoxysilane precursor ratio and the influence of water to Si molar ratio on the gelation and adsorption properties were investigated. An optimum water to Si molar ratio (8) gave the fastest gelation for all precursor ratios indicating a balance between the increase in rate of hydrolysis and a decrease in concentration of the monomers. Surface area analysis proved that in the dried gel, the organic groups are largely present on the pore walls and prevent the condensation of the silanol groups during drying. This in turn prevents pore collapse and further increases the total pore volume. The inclusion of the organically functionalised silane in the process further enhances the ambient pressure drying through this effect.     

AKD-Modification of bacterial cellulose aerogels in supercritical CO2

Different approaches towards hydrophobic modification of bacterial cellulose aerogels with the alkyl ketene dimer (AKD) reagent are presented. If AKD modification was performed in supercritical CO₂, an unexpectedly high degree of loading was observed. About 15 % of the AKD was bound covalently to the cellulose matrix, while the other part consisted of re-extractable AKD-carbonate oligomers, which are novel chemical structures described for the first time. These oligomers contain up to six AKD and CO₂ moieties linked by enolcarbonate structures. The humidity uptake from environments with different relative humidity by samples equipped with up to 30 % AKD is strongly reduced, as expected due to the hydrophobization effect. Samples above 30 % AKD, and especially at very high loading between 100 and 250 %, showed the peculiar effect of increased humidity uptake which even exceeded the value of unmodified bacterial cellulose aerogels.     

Effect of iron acetylacetonate on physico-chemical properties of waterglass based aerogels by ambient pressure drying

The effect of iron acetylacetonate on the physico-chemical properties of waterglass based silica aerogels by ambient pressure drying has been investigated. Doping the gels with iron acetylacetonat (FeAA) facilitates in the diminution of the density of the aerogels. The well established silica network provides effective confinement of FeAA nanoparticles which resists the collapse of silica network during ambient pressure drying. Therefore, in the present paper, the effects of FeAA on the physico-chemical properties of the aerogels have been studied by varying the FeAA:Na₂SiO₃ molar ratio from 3 × 10⁻⁴ to 6 × 10⁻⁴. The aerogels were prepared via ambient pressure drying and characterized by the bulk density, thermal conductivity and water contact angle. The aerogel’s surface morphology, elemental analysis and pore structure were characterized by means of EDAX and FTIR, TEM and N₂ adsorption- desorption analyzer. The high temperature hydrophobicity of these aerogels was checked by heating them in temperature controlled furnace. Silica aerogels with low density ~0.050 g/cc have been obtained using the molar ratio of Na₂SiO₃:H₂O:FeAA:Citric acid:TMCS at 1:146.67:3 × 10⁻⁴:0.54:9.46, respectively. EDAX and FTIR studies show that the iron species are entrapped in the mesoporous framework and not took part in the bonding with silica.     

Formation and rheological properties of the supercritical CO2-water pure interface

From the interfacial tension (gamma) measurement, we have analyzed the interfacial organization that occurs between pure H2O and pure CO2 from a kinetical and rheological point of view. This article is the followup to a previous one, where we showed that this equilibrated interface is composed of small H2O-CO2 cluster blocks [Tewes, F.; Boury, F. J. Phys. Chem. B 2004, 108, 2405]. By analyzing the variation of gamma with the square root of time, we found that the organization of the H2O-CO2 interface is, in the initial times, controlled by the diffusion of the CO2 molecules into the water. We compared the frictional coefficient determined from the measured CO2 diffusion coefficient with the frictional coefficient calculated from the Stokes equation (frictional ratio). From that, we concluded that it is a hydrated form of CO2 that diffuses and that the degree of hydration decreases with pressure. Rheological properties of the equilibrated interface vary with CO2 pressure, in the range of 50-90 bar, from a viscoelastic comportment to a purely elastic behavior, showing a change in the interfacial organization. The high equilibrium part of the elasticity (110 mN/m) obtained at 90 bar suggests a highly structured interface. Two phenomena could explain the interfacial rheological behavior: (i) an increase and a growth of the blocks H2O-CO2 cluster with the CO2 pressure or (ii) an increase in the interfacial capacity to form stable clusters under interfacial area compression.     

Polyethylenimine-impregnated mesoporous silica: effect of amine loading and surface alkyl chains on CO2 adsorption

Poly(ethyleneimine) (PEI) supported on pore-expanded MCM-41 whose surface is covered with a layer of long-alkyl chains was found to be a more efficient CO(2) adsorbent than PEI supported on the corresponding calcined silica and all PEI-impregnated materials reported in the literature. The layer of surface alkyl chains plays an important role in enhancing the dispersion of PEI, thus decreasing the diffusion resistance. It was also found that at low temperature, adsorbents with relatively low PEI contents are more efficient than their highly loaded counterparts because of the increased adsorption rate. Extensive CO(2) adsorption-desorption cycling showed that the use of humidified feed and purge gases affords materials with enhanced stability, despite limited loss due to amine evaporation.