Fundamental investigation on effect of microencapsulated water on expansion behavior of microcapsules

The microcapsules containing water were prepared with the suspension polymerization method, and the fundamental investigation was performed to make the effect of microencapsulated water on expansion behavior of microcapsules clear. In the experiment, only the volume of water added into styrene monomer was changed to make the effect of microencapsulated water volume clear, and three kinds of water contents were measured: namely, the initial water content for the microcapsules just after preparation, the middle water content for the microcapsules dried at 44°C for 24 hours, and the final water content for the microcapsules dried at 110°C for 1 hours. With increasing the added water volume, the initial water content increased; the middle water content decreased after increasing halfway through, and the final water content gradually decreased. Also, with increasing the added water volume, the drying rate of the microcapsules increased and the expansion ratio decreased. The water volume required to expand the microcapsules, in other words, the critical shell thickness required to prevent evaporation of water and to contribute to expansion of microcapsules is discussed.     

Water in micro- and nanofluidics systems described using the water potential

This Tutorial Review shows the behaviour of water in micro- and nanofluidic systems. The chemical potential of water ('water potential') conveniently describes the energy level of the water at different locations in and around the system, both in the liquid and gaseous state. Since water moves from high to low potential, the water potential enables us to predict and describe the direction of water movement inside systems and between systems and their surroundings. Practical examples of microfluidic devices illustrate the different contributions to the water potential (capillary, gravitational, entropic (osmotic) in liquid water; the partial vapour pressure in atmospheric water and van der Waals forces in water films) and the resulting water movement.     

水/Triton X-100/正丁醇/环己烷反相微乳液体系中水结构的FT-IR研究

用FT-IR法研究了水/辛烷基苯酚聚氧乙烯醚（Triton X-100）/正丁醇/环己烷组成的反相微乳液体系水池中存在的束缚、结合和自由3种不同的水的状态.分别考察了水与表面活性剂物质的量之比（Rw）、水油比φ（水与环己烷的质量比）、助剂正丁醇的含量对3种状态水含量的影响.发现在φ=2.8、m正丁醇/mTriton X...     

Wetting behavior of mixtures of water and nonionic polyoxyethylene alcohol

Five binary water + C4Ej mixtures, water + n-C4E0, water + 2-C4E0, water + iso-C4E0, water + n-C4E1, and water + iso-C4E1, were chosen to perform the surface/interfacial tension measurements over the experimental temperature range from 10 to 85 degrees C at the normal pressure by using a homemade pendent drop/bubble tensiometer. The symbol CiEj is the abbreviation of a nonionic polyoxyethylene alcohol CiH(2i+1)(OCH2CH2)jOH. The wetting behavior of the CiEj-rich phase at the interface separating gas and the aqueous phase is systematically examined according to the wetting coefficient resulting from the experimental data of surface/interfacial tensions measurements. For those systems with a lower critical solution temperature, for example, water + n-C6E2, water + n-C4E1, and water + iso-C4E1, a wetting transition from partial wetting to nonwetting is always observed when the system is brought to close to its lower critical solution temperature. On the other hand, to start with a partial wetting CiEj-rich phase, a wetting transition from partial wetting to complete wetting is always observed when the system is driven to approach its upper critical solution temperature. The effect of hydrophobicity of CiEj on the wetting behavior of the CiEj-rich phase at the interface separating gas and the aqueous phase was carefully investigated by using five sets of mixtures: (1) water + n-C4E0, water + n-C5E0, and water + n-C6E0; (2) water + 2-C4E0 and water + 2-C5E0; (3) water + 2-C4E0 and water + n-C4E0; (4) water + n-C4E1, water + n-C5E1, and water + n-C6E1; (5) water + n-C4E0 and water + n-C4E1. The CiEj-rich phase would tend to drive away from complete wetting (or nonwetting) to partial wetting with an increase in the hydrophobicity of CiEj in the binary water + CiEj system. All the wetting behavior observed in the water + CiEj mixtures is consistent with the prediction of the critical point wetting theory of Cahn.     

The interface between water and a hydrophobic gas

Classical molecular dynamics simulations have been performed to investigate the interface between liquid water and methane gas under methane hydrate forming conditions. The local environments of the water molecules were studied using order parameters which distinguish between liquid water, ice and methane hydrate phases. Bulk water and water/air interfaces were also studied to allow comparisons to be made between water molecules in the different environments and to determine the effects of the different methane densities studied. Good agreement between experimental and calculated surface tensions is obtained if long range corrections are included. The water surface is found to have a structure which is very similar to that of bulk water, but more tetrahedral, and more clathrate-like than ice-like. In these simulations the concentration of methane in water at the interface is shown to be appropriate for clathrates at higher gas densities (pressures). The orientation of water molecules around methane molecules in the interfacial region appears to depend only weakly on pressure and one of the difficulties in forming hydrate is the availability of water molecules tangential to the hydrate cage. At the interface, the water structure is more disordered than in the bulk water region with increased occurrence compared with the bulk of those angles and orientations found in the clathrate structure.     

压汞法测量玻璃毛细孔中的水和正癸烷

水在固体表面或在毛细孔玻璃中的性质,一直是人们感兴趣的问题。而靠近固体表面的水,其性质不同于体相(Bulk)水,也是为人所知的事实。已经知道,邻近水的热容、密度、粘度、电导及结构等都不同于体相水。但邻近水的厚度究竟为多少,或者说,这种固体表面对水的性质影响究竟是长程的还是短程的,目前还没有统一的结论。用压汞法测量多孔物质的孔体积,是人们已熟知的方法,但还没有人将其用于测量液体在毛细孔中的体积、密度等行为。我们尝试了用压汞法,测量具有确定孔径的毛细孔玻璃(CPG),在吸附了不同量水后孔体积的变化,进而计算了不同吸附层的水在CPG中的体积、密度。此外还测定了载有不同量正癸烷后,CPG孔体积的变化。     

Ferroelectric mobile water

In molecular dynamics simulations single-domain ferroelectric water is produced under ordinary ambient conditions utilizing carbon nanotubes open to a water reservoir. This ferroelectric water diffuses while keeping its proton-ordered network intact. The mobile/immobile water transitions and the step-wise changes in net polarization of water are observed to occur spontaneously. The immobile water becomes mobile by transforming into the single-domain ferroelectric water. Our general notion of relating a more highly ordered structure with a lower temperature has so far restricted researchers' attention to very low temperatures when experimenting on proton-ordered phases of water. The present study improves our general understanding of water, considering that the term 'ferroelectric water' has so far practically stood for 'ferroelectric ice,' and that single-domain ferroelectric water has not been reported even for the ice nanotubes.     

Extracting hydration sites around proteins from explicit water simulations

Two new methods are assessed for determining the location of hydration sites around proteins from computer simulation. Current methods extract hydration sites from peaks in the water density constructed in the protein frame. However, the dynamic nature of the water molecules, the nearby protein residues, and the protein reference frame as a whole tend to smear out the water density, making it more difficult to resolve sites. Two techniques are introduced to better resolve the water density. The first is to construct the water density from the time-averaged position of each water molecule in the protein frame while the water remains within a given distance of this averaged position. The second technique is to construct the water density from the time-averaged position of each water in the reference frame only of the nearby residues. Criteria for determining hydration sites from the water density are examined. Both techniques are found to significantly improve the detail in the water density and the number of hydration sites detected.     

Investigation of water diffusion process in ethyl cellulose-based films by attenuated total reflectance Fourier transform infrared spectroscopy and two-dimensional correlation analysis

Two-dimensional correlation spectroscopy (2Dcos) analysis on the time-resolved attenuated total reflectance Fourier transform infrared spectroscopy has been employed to investigate the diffusion behavior of water in ethyl cellulose/triethyl citrate (EC/TEC) films with varied TEC content. The diffusion coefficients of water in the EC-based films are calculated from the diffusion curves according to the Fickian Diffusion Model. And they are observed to increase with TEC content, possibly caused by the increased free volume in the film matrix. In the 2Dcos analysis, the broad O–H stretching vibration region is split into at least four bands, which can be assigned to four different states of water molecules, that is, bulk water, cluster water, relatively free water and free water. Moreover, it is found that as water molecules disperse into the EC-based films, cluster water with moderate hydrogen bonds diffuses faster than bulk water with strong hydrogen bonds. The relatively free water and free water are formed during the diffusion process due to their interactions with the films matrix, which makes water molecules confined and restricted in limited space.     

山梨醇改性聚乙烯醇体系的氢键作用及对水状态的影响

采用二维相关红外光谱研究了水渗透进入聚乙烯醇(PVA)及其改性基体过程中, 体系的氢键作用及对水状态的影响; 通过差示扫描量热分析(DSC)研究了改性剂山梨醇(S)对改性PVA中水状态的影响. 实验结果表明, S能通过其羟基与水形成较强氢键, 从而显著改变体系中水的状态及其蒸发行为, 使体系自由水含量逐渐减少, 水的蒸发峰温度升高.     

High-density hydration layer of lysozymes: molecular dynamics decomposition of solution scattering data

A characterization of the physical properties of protein hydration water is critical for understanding protein structure and function. Recent small-angle X-ray and neutron scattering data indicate that the density of water on the surface of lysozyme is significantly higher than in bulk water. Here, we provide an interpretation of the scattering results using a molecular dynamics simulation, which allows us to make quantitative predictions about density variations in the first hydration shell. The perturbation relative to bulk water involves statistically significant changes in the average water structure in the first hydration layer. The water density in the first hydration shell is increased by 5% with respect to the bulk. In regions of higher water density, the water dipoles align more parallel to each other and the number of hydrogen bonds per water molecule is higher. Increased water density is found for water molecules interacting with hydrogen and carbon atoms in the backbone or with nonpolar or negatively charged side-chain groups.     

A molecular dynamics study of a nafion polyelectrolyte membrane and the aqueous phase structure for proton transport

A molecular dynamics simulation study of hydrated Nafion at water contents ranging from 5 to 20 wt % was performed to examine the structure and dynamics of the hydrated polyelectrolyte system. The simulations show that the system forms segregated hydrophobic regions consisting primarily of the polymer backbone and hydrophilic regions with an inhomogeneous water distribution. We find that the water clustering strongly depends on the water content. At low water content, only isolated small water clusters are formed. As the water content increases, it becomes increasingly possible that a predominant majority of water molecules form a single cluster, suggesting that the hydrophilic regions become connected. We characterize the atomic structures formed within the system by various atomic pair correlation functions. The water structure factor shows a peak at q values corresponding to an intercluster distance about 2.5 nm and greater. With increasing water content, the distance moves to larger values, consistent with findings from scattering experiments. We find that the degree of solvation of hydronium ions by water molecules is a strong function of water content. At 5 wt %, a majority of the hydronium ions are hydrated by no more than two water molecules, prohibiting structural diffusion. As water content increases, the hydronium ions continue to become increasingly hydrated, resulting in structures capable of forming eigen ions, a necessary step in structural diffusion. Addressing the experimentally observed fact that conductivity in these membranes abruptly drops near 5 wt %, we find that both the local structure of the poorly hydrated hydronium ions and the disconnected nature of the global morphology of the water nanonetwork at low water content should contribute to poor conductivity.     

Water structure and dynamics at a silica surface: Pake doublets in 1H NMR spectra

Detailed knowledge about the dynamics and structure of liquids in the vicinity of a solid surface is important in several fields of research. In this study a homogeneous model system of colloidal and nonporous silica particles with a narrow particle size distribution was used to examine such properties of adsorbed water and 1-heptanol. Doublet (1)H water resonances ("Pake doublets") indicate a preferred spatial orientation for the water molecules, as well as a lower molecular density in the surface-induced water structures compared to bulk water. These surface-induced structures are found to extend at least 8 nm from the silica surface. T(1) relaxation measurements at several temperatures indicate weaker H-bonding in the adsorbed water compared to bulk water. T(2) relaxation measurements at several temperatures reveal the presence of two water phases and give quantitative information on the mobility of water molecules and proton exchange processes. The presence of 1-heptanol changes the water characteristics, primarily in the water phase closer to the surface, where water molecules experience decreased translational and increased rotational freedom. In the absence of water, adsorbed 1-heptanol forms surface aggregates encompassing several molecular layers, where the first adsorbed layer shows severe restrictions in mobility and subsequent layers are more mobile.     

三维壳聚糖材料中水的状态与其性能的关系

利用原位沉析法制备了具有层状结构的高强度三维壳聚糖(chitosan,CS)材料,由于CS分子结构中存在大量的亲水基团,容易吸附水分子.通过热分析(TGA,DSC)测试发现吸水后的CS材料中的水分是以3种不同的状态存在,结合水、中间态水和自由水.结合力学性能的方法分析不同状态的水对材料性能的影响.结果表明,结合水和CS以氢键紧密结合,有较好的热稳定性,对材料的力学性能有增强作用;CS棒材在环境中吸附的中间态水相当于一种增塑剂,随着水含量的增加,材料力学性能的下降符合Fermi经验公式;中间态水达到饱和之后,自由水开始出现,自由水和CS之间的作用力很弱,温度较低时会结晶成冰.自由水的渗透与中间态水比对材料的力学性能没有明显的影响.     

1-Propyl-4(5)-Methylimidazole Isomers for Temperature Swing Solvent Extraction

Temperature swing solvent extraction (TSSE) utilizes an amine solvent with temperature-dependent water solubility to dissolve water at a lower temperature to concentrate or crystallize the brine and the phases are separated. Then, the water in solvent mixture is heated to reduce water solubility and cause phase separation between the solvent and water. The solvent and de-salted water phases are separated, and the regenerated solvent can be recycled. Issues with current TSSE solvents include the high solvent in water solubility and the high solvent volatility. This project used the highly tunable platform molecule imidazole to create two 1-butylimidazole isomers, specifically 1-propyl-4(5)-methylimidazole, to test their effectiveness for TSSE. The imidazoles take in more water than their current state-of-the-art counterparts, but do not desalinate the product water and dissolve in water at higher concentrations. Thus, while imidazoles make intriguing candidates for TSSE, further work is needed to understand how to design imidazoles that will be useful for TSSE applications.     

Do probe molecules influence water in confinement?

The water inside reverse micelles can differ dramatically from bulk water. Some changes in properties can be attributed to the interaction of water molecules with the micellar interface, forming a layer of shell water inside the reverse micelle. The work reported here monitors changes in intramicellar water through chemical shifts and signal line widths in 51V NMR spectra of a large polyoxometalate probe, decavanadate, and from infrared spectroscopy of isotopically labeled water, to obtain information on the water in the water pool in AOT reverse micelles formed in isooctane. The studies reveal several things about the reverse micellar water pool. First, in agreement with our previous measurements, the proton equilibrium of the decavanadate solubilized within the reverse micelles differs from that in bulk aqueous solution, indicating a more basic environment compared to the starting stock solutions from which the reverse micelles were formed. Below a certain size, reverse micelles do not form when the polyoxometalate is present; this indicates that the polyanionic probe requires a layer of water to solvate it in addition to the water that solvates the surfactant headgroups. Finally, the polyoxometalate probe appears to perturb the water hydrogen-bonding network in a fashion similar to that in the interior surface of the reverse micelles. These measurements demonstrate the dramatic differences possible for water environments in confined spaces.     

Direct measurement of the capillary pressure characteristics of water–air–gas diffusion layer systems for PEM fuel cells

A method and apparatus for measuring the relationship between air–water capillary pressure and water saturation in PEMFC gas diffusion layers is described. Capillary pressure data for water injection and withdrawal from typical GDL materials are obtained, which demonstrate permanent hysteresis between water intrusion and water withdrawal. Capillary pressure, defined as the difference between the water and gas pressures at equilibrium, is positive during water injection and negative during water withdrawal. The results contribute to the understanding of liquid water behavior in GDL materials which is necessary for the development of effective PEMFC water management strategies.     

Oriented confined water induced by cationic lipids

We report on attenuated total reflection Fourier-transform infrared (ATR FTIR) spectroscopic measurements on oriented lipid multilayers of N,N-dimethyl-N,N-dioctadecyl-ammonium halides (DODAX, X = F, Cl, Br, I). The main goal of this study is the investigation of the structure and spectroscopic properties of water absorbed to these model membranes. Intensities of the water stretch absorptions were used to determine the amount of bound water. At high water activity, DODAF membranes bind ~11 water molecules/lipid while DODAC and DODAB adsorb 1-2 water/lipid and DODAI was hydrophobic. By adjustment of DODAF hydration to ~2 water molecules, stretching absorptions from water of the first hydration shell were accessible for the fluoride, chloride, and bromide analogs. The polarized measurements demonstrate highly confined and oriented water with infrared (IR) order parameters ranging from 0.2 to -0.4. Resolved IR water band components are attributed to different hydrogen-bonded populations. Complementary molecular dynamics simulations of DODAB strongly support the existence of differently hydrogen-bonded and oriented water within DODAB multilayers. A combination of both techniques was used for an assignment of water stretch band components to structures. The described cationic lipid systems are a prototype for a bottom-up approach to understand the IR spectroscopy of structured water at biological interfaces since they permit a defined increase of hydrophilic water-anionic interactions leading to extended water networks at membranes.     

Poly(vinyl methyl ether) hydrogels at temperatures below the freezing point of water—molecular interactions and states of water

Water interacting with a polymer reveals a number of properties very different to bulk water. These interactions lead to the redistribution of hydrogen bonds in water. It results in modification of thermodynamic properties of water and the molecular dynamics of water. That kind of water is particularly well observable at temperatures below the freezing point of water, when the bulk water crystallizes. In this work, we determine the amount of water bound to the polymer and of the so-called pre-melting water in poly(vinyl methyl ether) hydrogels with the use of Raman spectroscopy, dielectric spectroscopy, and calorimetry. This analysis allows us to compare various physical properties of the bulk and the pre-melting water. We also postulate the molecular mechanism responsible for the pre-melting of part of water in poly(vinyl methyl ether) hydrogels. We suggest that above ?60 °C, the first segmental motions of the polymer chain are activated, which trigger the process of the pre-melting.