Fe3O4-CuO-activated carbon composite as an efficient adsorbent for bromophenol blue dye removal from aqueous solutions

Dye wastewater from industries is posing tremendous health hazards. The lethal dyes can be eliminated using nanomaterials and scientific approach like adsorption which is facile, cheap, safe as well as ecofriendly. Fe₃O₄-CuO-AC composite was prepared by a hydrothermal method and used for the removal of dyes in wastewater. The composite material was characterized by various techniques such as XRD, SEM, EDS, TEM and FT-IR. The Fe₃O₄-CuO-AC composite was used to treat five types of dyes in water. Fe₃O₄-CuO-AC composite showed the highest adsorption capability for bromophenol blue (BPB) dye. The effects of initial concentration, pH, the amount of adsorbent and temperature were also studied. The optimum conditions were found to be 20 ppm dye concentration, pH 9, an adsorbent dose of 0.06 gL^─1 at 65 °C. A removal efficiency of 97% was obtained for BPB dye during 120 min of adsorption. Kinetic studies indicated that a pseudo-second order is the most suitable model for the adsorption process. The Fe₃O₄-CuO-AC composite showed better adsorption capacity as compare to Fe₃O₄-AC except for the Methyl green dye. The maximum adsorption capacity was found to be 88.60 mg/g for BPB. Additionally, the thermodynamic parameters (ΔS°, ΔH° and ΔG°) showed that the process was spontaneous and exothermic. All the above results revealed that the Fe₃O₄-CuO-AC compositecan be an effective adsorbent for removing dyes from wastewater.     

Nano-iron oxide-encapsulated chitosan microspheres as novel adsorbent for removal of Ni (II) ions from aqueous solution

The present study investigates the utility of composite beads of nano-particles of iron oxide and chitosan for removing Ni (II) ions from aqueous solution by batch and column adsorption techniques. In the batch mode experiment, the influence of pH, concentration, adsorbent dose, temperature, column mode, bed height, flow rate and initial concentration were studied on the adsorption profiles of nickel ions. The maximum uptake of Ni (II) ions was obtained at pH 4.0 in 30 min at room temperature.     

Recovery of Th(IV) from aqueous solution by reassembled collagen-tannin fiber adsorbent

A novel adsorbent, collagen immobilized tannin adsorbent (CITA), was prepared and its adsorption behaviors to Th(IV) were investigated. CITA was in fibrous state due to the reassembly of collagen molecules by the inducement of tannin. This adsorbent loaded a greater amount of tannin and exhibited higher adsorption capacity to Th(IV) than the tannin immobilized adsorbent prepared from collagen fiber. The adsorption of CITA to Th(IV) is mainly attributed to surface complexation, which is a pH- rather than an ionic strength-dependent process. The adsorption kinetics and isotherms were described by pseudo-second-order rate model and Freundlich equation, respectively. Column adsorption studies indicated that CITA is available for effectively recovering Th(IV) from aqueous solution.     

Preparation of Fe3O4@SiO2@layered double hydroxide core-shell microspheres for magnetic separation of proteins

Three-component microspheres containing an SiO(2)-coated Fe(3)O(4) magnetite core and a layered double hydroxide (LDH) nanoplatelet shell have been synthesized via an in situ growth method. The resulting Fe(3)O(4)@SiO(2)@NiAl-LDH microspheres display three-dimensional core-shell architecture with flowerlike morphology, large surface area (83 m(2)/g), and uniform mesochannels (4.3 nm). The Ni(2+) cations in the NiAl-LDH shell provide docking sites for histidine and the materials exhibit excellent performance in the separation of a histidine (His)-tagged green fluorescent protein, with a binding capacity as high as 239 μg/mg. The microspheres show highly selective adsorption of the His-tagged protein from Escherichia coli lysate, demonstrating their practical applicability. Moreover, the microspheres possess superparamagnetism and high saturation magnetization (36.8 emu/g), which allows them to be easily separated from solution by means of an external magnetic field and subsequently reused. The high stability and selectivity of the Fe(3)O(4)@SiO(2)@NiAl-LDH microspheres for the His-tagged protein were retained over several separation cycles. Therefore, this work provides a promising approach for the design and synthesis of multifunctional LDH microspheres, which can be used for the practical purification of recombinant proteins, as well as having other potential applications in a variety of biomedical fields including drug delivery and biosensors.     

Superparamagnetic high-magnetization microspheres with an Fe3O4@SiO2 core and perpendicularly aligned mesoporous SiO2 shell for removal of microcystins

Superparamagnetic microspheres with an Fe3O4@SiO2 core and a perpendicularly aligned mesoporous SiO2 shell were synthesized through a surfactant-templating sol-gel approach. The microspheres possess high magnetization (53.3 emu/g), high surface area (365 m2/g), large pore volume (0.29 cm3/g), and uniform mesopore (2.3 nm). By using the unique core-shell microspheres with accessible large pores and excellent magnetic property, a fast removal of microcystins with high efficiency (>95%) can be achieved.     

Ethylenediamine functionalized magnetic graphene oxide (Fe3O4@GO-EDA) as an efficient adsorbent in Arsenic(III) decontamination from aqueous solution

Research on Chemical Intermediates - Magnetic graphene oxide nanocomposite functionalized with ethylenediamine (Fe3O4@GO-EDA) was synthesized as a recyclable nanoadsorbent for As(III)...     

Halloysite nanotubes: an eco-friendly adsorbent for the adsorption of Th(IV)/U(VI) ions from aqueous solution

Journal of Radioanalytical and Nuclear Chemistry - In this study, the halloysite nanotubes was characterized and the adsorption of Th(IV) and U(VI) on halloysite nanotubes was investigated as a...     

Fe3O4-modified sewage sludge biochar for U(VI) removal from aqueous solution: performance and mechanism

Journal of Radioanalytical and Nuclear Chemistry - Sewage sludge-derived biochar (SSB) was prepared at 600 °C pyrolysis temperature and modified by co-precipitation with Fe3O4 to...     

多功能Fe3O4@SiO2 Janus颗粒

采用溶剂热法和溶胶-凝胶法制备了顺磁性Fe₃O₄@SiO₂颗粒,以Pickering乳液界面保护法实现颗粒表面分区获得Fe₃O₄@SiO₂ Janus颗粒,进一步选区复合生长Pt或Ag纳米颗粒制备Fe₃O₄@SiO₂-Pt和Fe₃O₄@SiO₂-Ag Janus颗粒.Fe₃O₄@SiO₂-Pt Janus颗粒的Pt一侧进行催化过氧化氢的反应,具有自驱动功能.因其顺磁性和两亲性,Fe₃O₄@SiO₂-Ag Janus颗粒能够作为磁响应颗粒乳化剂稳定油水乳液,并将Ag的催化功能引入界面.     

Europium(III) removal from aqueous solution using citric acid modified alkalized Mxene as an adsorbent

Journal of Radioanalytical and Nuclear Chemistry - Effective removal of radioactive nuclides from industrial activities by safe and stable reusable adsorbents has attracted researchers’...     

Preparation of Functionalized Fe3O4@SiO2 Magnetic Nanoparticles for Monoclonal Antibody Purification

Magnetic Fe₃O₄@SiO₂ nanoparticles with superparamagnetic properties were prepared via a reverse mi-croemulsion method at room temperature. The as-prepared samples were characterized by transmission electron mi-croscopy(TEM), X-ray diffractometry(XRD), and vibrating sample magnetometry(VSM). The Fe₃O₄@SiO₂ nanoparticles were modified by (3-aminopropyl)triethoxysilane(APTES) and subsequently activated by glutaraldehyde(Glu). Protein A was successfully immobilized covalently onto the Glu activated Fe₃O₄@SiO₂ nanoparticles. The adsorption capacity of the nanoparticles was determined on an ultraviolet spectrophotometer(UV) and approximately up to 203 mg/g of protein A could be uniformly immobilized onto the modified Fe₃O₄@SiO₂ magnetic beads. The core-shell of the Fe₃O₄@SiO₂ magnetic beads decorated with protein A showed a good binding capacity for the chime-ric anti-EGFR monoclonal antibody(anti-EGFR mAb). The purity of the anti-EGFR mAb was analyzed by virtue of HPLC. The protein A immobilized affinity beads provided a purity of about 95.4%.     

Preparation for Magnetic Nanoparticles Fe3O4 and Fe3O4@SiO2 and Heterogeneous Fenton Catalytic Degradation of Methylene Blue

Dyestuff textile wastewater treatment has become a research hotspot due to its high chroma, poor biodegradability, and low toxicity characteristics. In this paper, we have synthesized magnetic Fe₃O₄ and core‐shell Fe₃O₄@SiO₂ materials by hydrothermal methods. These materials were characterized by XRD, TEM, N₂ adsorption‐desorption and so on. These materials’ heterogeneous Fenton has been applied to dye wastewater treatment. Methylene blue was used as a typical target of dye wastewater. Decolorization ratios of methylene blue were determined by different nanostructure composites catalysts. A serious of results of study showed that decolorization ratios of magnetic nanoparticles and core‐shell composites arrived at above 90 % under the weakly acidic or neutral conditions and room temperature. When these catalysts were reused, the results show that Fe₃O₄@SiO₂ materials were possessed with good cycle performance.     

Fe3O4 and gamma-Fe2O3 nanoparticles for the adsorption of Co2+ from aqueous solution

The adsorption of Co2+ ions from nitrate solutions using iron oxide nanoparticles of magnetite (Fe3O4) and maghemite (gamma-Fe2O3) has been studied. The adsorption of Co2+ ions on the surface of the particles was investigated under different conditions of oxide content, contact time, solution pH, and initial Co2+ ion concentration. It has been found that the equilibrium can be attained in less than 5 min. The maximum loading capacity of Fe3O4 and gamma-Fe2O3 nanoparticles is 5.8 x 10(-5) and 3.7 x 10(-5) mol m(-2), respectively, which are much higher than the previously studied, iron oxides and conventional ion exchange resins. Co2+ ions were also recovered by dilute nitric acid from the loaded gamma-Fe2O3 and Fe3O4 with an efficiency of 86 and 30%, respectively. That has been explained by the different mechanisms by including both the surface and structural loadings of Co2+ ions. The surface adsorption of Co2+ on Fe3O4 and gamma-Fe2O3 nanoparticles has been found to have the same mechanism of ion exchange reaction between Co2+ in the solution and proton bonded on the particle surface. The conditional equilibrium constants of surface adsorption of Co2+ on Fe3O4 and gamma-Fe2O3 nanoparticles have been determined to be log K=-3.3+/-0.3 and -3.1+/-0.2, respectively. The structural loading of Co2+ ions into Fe3O4 lattice has been found to be the ion exchange reaction between Co2+ and Fe2+ while that into gamma-Fe2O3 lattice to fill its vacancy. The effect of temperature on the adsorption of Co2+ was also investigated, and the value of enthalpy change was determined to be 19 kJ mol(-1).     

Poly（vinylpyridine） adsorbent for the removal of SIPA from its aqueous solution

Poly(vinylpyridine) WH-225 resin was prepared and characterized.Compared with the commercial hypercrosslinked adsorbent NDA-100 and macroporous adsorbent XAD-4 resins,the newly synthesized poly(vinylpyridine) WH-225 resin exhibited the highest adsorption capacity toward SIPA from aqueous solution.     

Preparation of core-shell magnetic Fe3O4@SiO2-dithiocarbamate nanoparticle and its application for the Ni2+, Cu2+ removal

A typical superparamagnetic nanoparticles-based dithiocarbamate absorbent (Fe₃O₄@SiO₂-DTC) with core-shell structure was applied for aqueous solution heavy metal ions Ni²⁺, Cu²⁺ removal.     

Synthesis of novel Fe3O4@SiO2@CeO2 microspheres with mesoporous shell for phosphopeptide capturing and labeling

Fe(3)O(4)@SiO(2)@CeO(2) microspheres with magnetic core and mesoporous shell were synthesized, and the multifunctional materials were utilized to capture phosphopeptides and catalyze the dephosphorylation simultaneously, thereby labeling the phosphopeptides for rapid identification.     

Modifying attapulgite clay by ammonium citrate tribasic for the removal of radionuclide Th(IV) from aqueous solution

The ammonium citrate tribasic was successfully modified to attapulgite clay and the effect of modifying was characterized by FTIR and XRD techniques. Experimental results showed that the ammonium citrate tribasic modified attapulgite clay had a strong sorption ability to remove Th(IV) from aqueous solutions. The sorption of Th(IV) from aqueous solutions has been systematically investigated as a function of several variables including contact time, solid content, pH, ionic strength, Fulvic acid (FA)/humic acid (HA) and temperature under ambient conditions. The results indicate that the sorption of Th(IV) onto ammonium citrate tribasic modified attapulgite clay is strongly dependent on pH, Th(IV) initial concentration, ionic strength, temperature and HA/FA. Surface complexation and ionic exchange are the main sorption mechanisms. Sorption of Th(IV) onto ammonium citrate tribasic modified attapulgite is quick and can be fitted by a pseudo-second-order rate model very well. Sorption of Th(IV) onto ammonium citrate tribasic modified attapulgite is promoted at higher temperature and the sorption reaction is an endothermic process. Langmuir isotherm model fits the experimental data better than Freundlich and D-R isotherm models. The results suggest that the ammonium citrate tribasic modified attapulgite sample is a suitable material in the preconcentration and solidification of radionuclide Th(IV) from large volumes of aqueous solutions.     

蛋黄-壳结构Fe3O4@SiO2@PMO磁性微球的制备及对漆酶的固定化

以蛋黄-壳结构的Fe₃O₄@SiO₂@PMO磁性微球作为载体, 采用交联法对漆酶进行固定, 考察了戊二醛浓度等对固定效果的影响, 并对固定后漆酶的活性进行了研究. 结果表明, 蛋黄-壳结构的磁性微球负载漆酶仅需6 h, 磁性微球对漆酶的固载量高达475 mg/g. 固定后漆酶的稳定性显著提高, 在pH=2.5~4.5的强酸性条件下, 固定后漆酶酶活仍可保持70%以上, 即使温度升高至60 ℃, 固定后漆酶的相对酶活仍保持65%以上. 这说明漆酶经所合成的材料固定后, 其耐酸和耐热能力都明显优于游离漆酶. 包覆的Fe₃O₄粒子使得材料很容易经磁铁分离法回收, 固定后漆酶经磁分离循环使用10次后仍然能保留85%的酶活, 具有良好的可操作性和稳定性, 有效降低了漆酶的使用成本.     

Novel Fe3O4/hydroxyapatite/β‐cyclodextrin nanocomposite adsorbent: Synthesis and application in heavy metal removal from aqueous solution

The increased global concern on environmental protection has made researchers focus their attention on new and more efficient methods of pollutant removal. In this research, novel nanocomposite adsorbents,i.e., magnetic hydroxyapatite (Fe₃O₄@HA) and magnetic hydroxyapatite β‐cyclodextrin (Fe₃O₄@HA‐CD) were synthesized and used for heavy metal removal. The adsorbents were characterized by FTIR, XRD, TGA, VSM, and SEM. In order to investigate the effect of β‐cyclodextrin (β‐CD) removal efficiency, adsorption results of nine metal ions were compared for both adsorbents. β‐CD showed the most increasing effect for Cd²⁺ and Cu²⁺ removal, so these two ions were selected for further studies. The effect of diverse parameters including pH, contact time, initial metal ion concentration and adsorbent dosage on the adsorption process was discussed. The optimum pH was 6 and adsorption equilibrium was achieved after 1 hr. Adsorption kinetic data were well fitted by pseudo‐second‐order model proposing that metal ions were adsorbed via chemical reaction. Adsorption isotherm was best described by the Langmuir model, and maximum adsorption capacity for Cd²⁺ and Cu²⁺ was 100.00 and 66.66 (mg/g), respectively. Desorption experiment was also done, and the most efficient eluent used for desorption of metal ions was EDTA (0.001 M) with 91% and 88% of Cd²⁺ and Cu²⁺ release, respectively. Recyclability studies also showed a 19% decrease in the adsorption capacity of the adsorbent after five cycles of regeneration. Therefore, the synthesized adsorbents were recognized as potential candidates for heavy metal adsorption applications.