Electrodeposition of hyaluronic acid and hyaluronic acid–bovine serum albumin films from aqueous solutions

Hyaluronic acid (HYH) films were prepared from aqueous sodium hyaluronate (HYNa) solutions by anodic electrodeposition. The film thickness was varied in the range of 0–20 μm by the variation of the deposition time and HYNa concentration. The deposition rate was low at HYNa concentration below 1 g L⁻¹ and increased significantly in the range of 3–5 g L⁻¹. The addition of bovine serum albumin (BSA) to the HYNa solutions resulted in increased deposition yield, which was attributed to the formation of composite HYH–BSA films. The thickness of the HYH–BSA films deposited by anodic electrodeposition was varied in the range of 0–80 μm. The HYH and composite HYH–BSA films were studied by scanning electron microscopy, thermogravimetric analysis, differential thermal analysis, Fourier transform infrared spectroscopy and circular dichroism spectroscopy. The deposition mechanism and kinetics of deposition are discussed.     

Preparation of magnetic modified chitosan and adsorption of Zn²⁺ from aqueous solutions

The performance of a cross-linked magnetic modified chitosan (CMMC), which has been coated with magnetic fluids and cross-linked with glutaraldehyde, has been investigated for the adsorption of Zn(2+) from aqueous solutions. The CMMC with a diameter range of 20-50 nm was prepared. The effects of pH and the contact time for the adsorption have been discussed, and the optimal adsorption conditions for the adsorption of Zn(2+) have been obtained. The research results showed that CMMC was highly efficient for fast adsorption of Zn(2+) within the first 25 min, and adsorption equilibrium could be achieved in 30 min. Equilibrium studies showed that the data of Zn(2+) adsorption followed the Langmuir model. The maximum adsorption capacity for Zn(2+) was estimated to be 32.16 mg/g with a Langmuir adsorption equilibrium constant of 0.01 L/mg at 298 K, which demonstrated that the CMMC had obvious efficient adsorption of Zn(2+). The CMMC was stable and easily recovered. Moreover, the adsorption rate was about 90% of the initial saturation adsorption capacity after being used five times.     

Synthesis and characterization of activated carbon@zerovalent iron–nickel nanoadsorbent for highly efficient removal of Reactive Orange 16 from aqueous sample: experimental design,kinetic, isotherm and thermodynamic studies

Research on Chemical Intermediates - A simple and fast method based on activated carbon@nanozerovalent iron–nickel (AC@nZVI/Ni) nanoadsorbent was developed for highly efficient removal of...     

Ozonated graphene oxides as high efficient sorbents for Sr(Ⅱ) and U(Ⅵ) removal from aqueous solutions

Ozone was used to oxidize graphene oxides(GO) to generate ozonated graphene oxides(OGO) with higher oxygen-containing functional groups. The as-prepared OGO was characterized by Fourier transformed infrared spectroscopy(FTIR), scanning electron microscopy(SEM) and X-ray photoelectron spectroscopy(XPS). Based on the results of potentiometric acid-base titrations, the total carboxylic acid concentration on OGO surface was calculated to be 3.92 mmol/g, which was much higher than that on GO surface. The results of adsorption experiments indicated that the adsorption capacities of OGO for Sr(II) and U(VI) removal were improved significantly after ozonization.     

Preparation of graphene oxide–chitosan composite and adsorption performance for uranium

The composite adsorbent graphene oxide–chitosan was prepared using graphite and chitosan as the initial materials. The structures and morphology of the products were characterized by Fourier transform infrared spectroscopy (FT-IR) and scanning electron microscopy. The products were used to remove uranium from aqueous solution by batch adsorption experiments. The effects of pH, adsorbent dosage, contact time, initial uranium concentration and temperature on the uranium removal were investigated, and the results were fitted by the adsorption isotherm models. The adsorption kinetic and thermodynamic were also studied in detail.     

Thermodynamic parameters characterizing adsorption of organic compounds from aqueous solutions on iron oxide α-Fe2O3

Adsorption of a series of organic compounds on the surface of -Fe₂O₃ is studied. The experimental data are analyzed using the Frumkin and Langmuir isotherms. The standard Gibbs energies of adsorption G _A ⁰ and G _ads ⁰ corresponding to different standard states are estimated.Translated from Zhurnal Prikladnoi Khimii, Vol. 77, No. 9, 2004, pp. 1446–1451.Original Russian Text Copyright © 2004 by Afanasev, Aleksandrova, Akulova.     

Erratum on “Ozonated graphene oxides as high efficient sorbents for Sr(II) and U(VI) removal from aqueous solutions”

Science China Chemistry - We regret that our article “Ozonated graphene oxides as high efficient sorbents for Sr(II) and U(VI) removal from aqueous solutions ” (Sci China Chem, 2016,...     

A comparative adsorption study of β-naphthol on four polymeric adsorbents from aqueous solutions

Adsorptive removal of aromatic compounds from aqueous solutions by polymeric adsorbents has attracted many concerns in recent years. A comparative adsorption study including equilibria, kinetics and column dynamics of β-naphthol from aqueous solutions was carried out using two hypercrosslinked polymeric adsorbents (HJ-1 and TEPA) we developed and two commercial polymeric adsorbents (XAD-4 and XAD-7). The adsorption isotherms could be well described by the Freundlich equation, and the adsorption equilibrium capacities of β-naphthol followed an order of q(e)((TEPA))>q(e)((HJ-1))>q(e)((XAD-4))>q(e)((XAD-7)). The isosteric adsorption enthalpies on HJ-1 and TEPA decreased with increasing adsorption fractional loading, while a constant enthalpy was observed for XAD-4 and XAD-7, implying that HJ-1 and TEPA had a heterogeneous surface while XAD-4 and XAD-7 possessed a homogenous surface. The surface energetic heterogeneity of HJ-1 and TEPA could be well characterized by the Do's model. The adsorption kinetics were fitted by both pseudo-first-order and pseudo-second-order rate equations, and the intra-particle diffusion was found to be the rate-limiting step. The adsorption breakthrough data were well correlated by the Thomas and Clark models, and the dynamic capacities for TEPA, HJ-1, XAD-4 and XAD-7 adsorbents were calculated to be 341.7, 321.6, 268.0 and 173.8 mg/g dry resin, which were within 90% of the corresponding equilibrium capacities obtained in the batch experiments.     

Removal of cadmium(II) and lead(II) ions from model aqueous solutions using sol–gel-derived inorganic oxide adsorbent

A study was conducted concerning the preparation and application of a novel synthetic oxide adsorbent of MgO-SiO₂ type. The material was prepared via a sol–gel route, utilizing magnesium ethoxide and tetraethoxysilane as precursors of magnesium oxide and silica respectively, and ammonia as a catalyst. The powder was comprehensively analyzed with regard to chemical composition (EDS method), crystalline structure, morphology, characteristic functional groups, electrokinetic stability and porous structure parameters (BET and BJH models). The synthesized oxide adsorbent is amorphous, with irregularly shaped particles, a relatively large surface area of 612 m²/g, and negative surface charge over almost the whole pH range. Comprehensive adsorption studies were performed to investigate the adsorption of Cd(II) and Pb(II) ions on the MgO–SiO₂ oxide adsorbent, including evaluation of adsorption kinetics and isotherms, the effect of pH, contact time and mass of adsorbent. It was shown that irrespective of the conditions of the adsorption process, the synthesized MgO–SiO₂ adsorbent exhibits slightly better affinity to lead(II) than to cadmium(II) ions (sorption capacity of 102.02 mg(Pb²⁺)/g and 94.05 mg(Cd²⁺)/g). The optimal time for removal of the analyzed metal ions was 60 min, although adsorption reached equilibrium within 10 min for Pb(II) and within 15 min for Cd(II) ions, which was found to fit well with a type 1 pseudo-second-order kinetic model. Additionally, adsorption efficiency was affected by the pH of the reaction system—better results were obtained for pH ≥7 irrespective of the type of metal ion.     

Electrochemical determination of picric acid based on platinum nanoparticles–reduced graphene oxide composite

Platinum nanoparticles–reduced graphene oxide composite-modified glassy carbon electrode (PtNPs–rGO/GCE) was developed as a simple, selective and sensitive electrochemical sensor for determination of picric acid (PA). Cyclic voltammogram (CV) of PA showed three well-defined irreversible reduction peaks at the potentials of ?0.43, ?0.57 and ?0.66 V versus Ag/AgCl. In this work, the interference effect of other nitrophenol compounds (NPhCs) was significantly reduced by appropriate adjusting of pH. Square wave voltammetry was used for quantification of PA in the range of 5–500 µM (1.15–115 mg L^?1) with practical detection limit of 1 µM (0.23 mg L^?1). The proposed sensor was successfully applied for the determination of PA in two natural water samples.     

Co-precipitation of plutonium(IV) and americium(III) from nitric acid–oxalic acid solutions with bismuth oxalate

This study presents analytical methods for the determination of gross beta, ⁹⁰Sr, ²²⁶Ra and Pu isotopes using samples in the IAEA-TEL-2015-04 ALMERA Proficiency Test exercise. Samples for gross beta were prepared by evaporation and then analyzed using a gas proportional counter. ⁹⁰Sr in the liquid sample was concentrated as SrCO₃ precipitates and purified by Sr resin. Pu isotopes and ⁹⁰Sr in the soil sample were extracted from the sample by mineral acid leaching and separated using TEVA and Sr resin, respectively. Pu isotopes were determined by alpha spectrometry and ⁹⁰Sr were determined with a liquid scintillation counter. Radium in the soil sample was extracted by LiBO₂ fusion, and the radon-emanation method using LSC was applied for the determination of ²²⁶Ra.     

Effects of acrylic acid incorporation on the pressure–temperature behavior and the calorimetric properties of poly(N-isopropylacrylamide) in aqueous solutions

 We studied the effects of pH on the pressure–temperature dependence of coil–collapse transition for aqueous solutions of copolymers of N-isopropylacrylamide and acrylic acid (Ac). At low pressures, the transition temperature (T _tr) increased with pressure, but T _tr decrease with increasing pressure at pressures higher than 50–100 MPa. By increasing the pH, the transition contour shifted to a higher temperature. When the Ac content was increased, the effects of pH became more evident. From a calorimetric study at atmospheric pressure, ΔH _tr was found to become smaller by increasing the portion of the ionized residues in the copolymer. The ratio to the van't Hoff enthalpy changes became larger with an increase in pH, which indicated that the production of charge decreased the cooperative domain size. Received: 19 July 1999 /Accepted in revised form: 7 September 1999     

Effect of temperature on partial molar volumes and viscosities of aqueous solutions of α-dl-Aminobutyric acid,dl-Norvaline and dl-Norleucine

In this work, we present experimental results for partial molar volumes and viscosities of aqueous solutions of α-dl-aminobutyric acid, dl-norvaline and dl-norleucine at 288.15, 293.15, 298.15 and 303.15?K. The thermodynamic behavior of aqueous amino acid solutions is compared with that reported for glycine and α-alanine in water and is discussed in terms of group additivity and electrostriction.

The temperature dependence of the infinite dilution partial molar volumes and the B viscosity coefficients are interpreted in terms of amino acid hydration. According to the usual hydrophobicity criteria, the amino acids considered do not have a hydrophobic character and their behavior is dominated by the polar groups.     

Facile synthesis of mesoporous magnesium oxide–graphene oxide composite for efficient and highly selective adsorption of hazardous anionic dyes

Mesoporous magnesium oxide–graphene oxide composite (MGC) has been synthesized using a facile post-immobilization method by mixing pre-synthesized magnesium oxide (MgO) with graphene oxide (GO). MgO used for fabrication of the composite has been synthesized using an environment-friendly method involving gelatin as a template. XRD, Raman and EDX analyses have confirmed the presence of MgO and GO in the composite. FTIR and SEM analyses of synthesized MGC have further elucidated the surface functionalities and morphology, respectively. Using N₂ adsorption–desorption isotherm, BET surface area of MGC has been calculated to be 55.9 m² g^?1 and BJH analysis confirmed the mesoporous nature of MGC. The application of synthesized MGC as a selective adsorbent for various toxic anionic dyes has been explored. Batch adsorption studies have been carried out to investigate the influence of different adsorption parameters on the adsorption of two anionic dyes: indigo carmine (IC) and orange G (OG). The maximum adsorption capacities exhibited by MGC for IC and OG are 252.4 and 24.5 mg g^?1, respectively. Plausible mechanism of dye adsorption has been explained in detail using FTIR analysis. In a mixture of cationic and anionic dyes, MGC selectively adsorbs anionic dyes with high separation factors, while in binary mixtures of anionic dyes, both dyes are adsorbed efficiently. Thus, MGC has been shown to be a potential adsorbent for the selective removal of anionic dyes from wastewater.

     

Characteristic and mechanism of Cr(Ⅵ) adsorption by ammonium sulfamate-bacterial cellulose in aqueous solutions

A new adsorbent, ammonium sulfamate-bacterial cellulose (ASBC), was prepared through chemical modifications of bacterial cellulose. The process of adsorbing Cr(Ⅵ) including its isotherm and kinetics, was measured and studied. The results showed that pH value was a very important parameter to the adsorbing efficiency. The adsorption kinetics can be described by a pseudo-second rate model and a particle diffusion equation. Both physical and chemical adsorptions existed in the adsorption process, but chemical adsorption was more dominatant. And particles internal diffusion was not the only rate controlling step. The adsorption equilibrium can be described by the Langmuir type, which indicated that a typical single-molecule layer adsorption of Cr(Ⅵ) by ASBC could be described. And the rate of adsorption followed the Slips model well, which indicated that ASBC had some multiphase and asymmetry. The coordination adsorption and ion exchange effect were the main mechanisms of chemical adsorption. The absorbed Cr(Ⅵ) can be desorbed effectively by 0.5 mol/L EDTA or HCl from the adsorbent, which could make it be reusable.     

Equilibrium and kinetic studies on the adsorption of VB_(12) onto CMK-3

The adsorption of VB12 onto CMK-3 was studied as a function of temperature and initial VB12 concentration. The highest VB12 adsorption capacity was determined as 353.4 mg/g at 40℃. Adsorption data were well described by the Langmuir model, although they could be modelled by the Freundlich equation. The pseudo-first-order and pseudo-second-order kinetic models were applied to test the experimental data. The pseudo-second-oider kinetic model provided the best correlation of the experimental data compared to the pseudo-nrsi-order model.     

Study on surface adsorption from cationic surfactant–electrolyte mixed aqueous solution including BF 4 − ion

The surface tension of aqueous mixtures of dodecyltrimethylammonium tetrafluoroborate (DTABF₄) and sodium tetrafluoroborate (NaBF₄) was measured as a function of total molality and composition of DTABF₄ at 298.15 K. The results were analyzed by originally developed thermodynamic equations and compared with those of dodecyltrimethylammonium bromide (DTAB)–sodium bromide (NaBr) mixed system. It was indicated that BF₄⁻ ions reduce the repulsion between DTA⁺ ions more effectively than Br⁻ ions in the adsorbed film. To investigate this difference more closely, the surface tension of DTAB–NaBF₄ and DTABF₄–NaBr mixed system was also measured. The data analysis revealed that BF₄⁻ ions are adsorbed positively even for the pure NaBF₄ system and preferentially to Br⁻ ions in these mixtures. Furthermore, it was concluded that the side-by-side arrangement suggested in the adsorbed film of 1-hexyl-3-methylimidazolium tetrafluoroborate (HMIMBF₄) is due to not only the positive adsorption of BF₄⁻ ions but also the capability of hydrogen bond formation between imidazolium ion and BF₄⁻ ions.     

Assessment of adsorption properties of inorganic–organic hybrid cyclomatrix type polyphosphazene microspheres for the removal of Pb(II) ions from aqueous solutions

Abstract

Inorganic–organic hybrid cyclomatrix type polyphosphazene microspheres (poly[cyclotriphosphazene-co-(4,4′-diaminodiphenylmethane)]) (HDMS) and poly[cyclotetraphosphazene-co-4,4′-diaminodiphenylmethane)] (ODMS) were prepared to investigate their possible use as alternative adsorbents for the comparative study on Pb(II) ions removal from aqueous solutions. The structures of the microspheres were elucidated by Fourier Transform Infrared (FTIR) spectroscopy and Dynamic Light Scattering (DLS) measurements, and the surface morphologies were also observed by Scanning Electron Microscopy (SEM). The adsorption of Pb(II) ions onto HDMS and ODMS from aqueous solutions was examined by means of pH, temperature, contact time and concentration. Furthermore, adsorption kinetics and isotherm models were applied and the experimental data fitted well with Langmuir isotherm and pseudo-second-order kinetic models. The maximum adsorption capacities of HDMS and ODMS for Pb(II) ions were obtained as 157.8 and 308.0?mg g^?1 at 20?°C and pH 5.5, respectively.