首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
La0.6Sr0.4Co1-yFeyO3(y=0.2,0.8)复合氧化物混合导电性能研究   总被引:2,自引:0,他引:2  
采用甘氨酸-硝酸盐(GNP)法制备了La0.6Sr0.4Co1-yFeyO3(y=0.2,0.8)g合氧化物,研究了材料的结构、电子-离子混合导电性能及其相关性。结果表明,La0.6Sr0.4Co1-yFeyO3(y=0.2,0.8)合成粉料的颗粒细小均匀(~100nm),陶瓷形成菱形六面体钙钛矿结构。与La0.6Sr0.4Co0.2Fe0.8O3(y=0.8)陶瓷相比,La0.6Sr0.4Co0.8Fe0.2O3(y=0.2)陶瓷的晶粒尺寸大、致密度较高。在La0.6Sr0.4Co0.8Fe0.2O3(y=0.2)陶瓷中观察到Co^3+离子歧化对电子导电性能的影响。与La0.6Sr0.4Co0.2Fe0.8O3(y=0.8)陶瓷相比,La0.6Sr0.4Co0.8Fe0.2O3(y=0.2)陶瓷具有更优异的电子-离子混合导电性能,材料在混合导电性能上的差异与其电子结构和显微结构紧密相关。  相似文献   

2.
采用柠檬酸络合法制备B位掺杂的纳米钙钛矿复合氧化物La0.8Sr0.2Mn1-xCoxO3(x=0,0.3,0.5,1.0)。应用X射线衍射法(XRD)进行结构的测定与分析,并结合扫描电镜(SEM)和热磁曲线(M-T曲线)的实验结果,研究这4种样品的结构和磁性之间的关系。X射线衍射实验分析表明4个样品均属六方晶系,M-T曲线得出的1/χ-T曲线表明:La0.8Sr0.2MnO3是铁磁性,La0.8Sr0.2Mn0.7Co0.3O3和La0.8Sr0.2Mn0.5Co0.5O3是亚铁磁性,而La0.8Sr0.2CoO3是反铁磁性的。利用电镜观察到前3种样品均为颗粒状,颗粒之间首尾相接形成链状结构,并进一步由链状结构支起一个个的空间网状结构,最后一种样品为较为分散的颗粒。  相似文献   

3.
分别使用柠檬酸络合法和浸渍法制备了钙钛矿型复合氧化物催化剂LaMn1-xPdxO3(x=0,0.01,0.02,0.03,0.04)和不同Ag负载量的Ag/LaMn0.99Pd0.01O3催化剂.使用XRD,BET手段对各催化剂进行了表征,同时在反应条件:NO 0.1%,O2 8%,H2O 0或10%,SO2 0或0.008%,N2为平衡气体,接触时间为0.03g·s·ml-1(GHSV=30000h-1)下对催化剂的活性进行了考察.实验结果发现,当贵金属Pd在B位部分替代Mn时,替代量x=0.01时的催化剂对于催化氧化分解NO反应具有最高活性.另外,在LaMn0.99Pd0.01O3催化剂上负载2%Ag也明显提高了催化剂的活性.而且LaMn0.99Pd0.01O3和2%Ag/LaMn0.99Pd0.01O3催化剂尽管抗水性能不好,但却具有较强的抗SO2性能.  相似文献   

4.
分别使用柠檬酸络合法和浸渍法制备了钙钛矿型复合氧化物催化剂LaMn1-xPdxO3(x=0,0.01,0.02,0.03,0.04)和不同Ag负载量的Ag/LaMn0.99Pd0.01O3催化剂.使用XRD,BET手段对各催化剂进行了表征,同时在反应条件NO 0.1%,O2 8%,H2O 0或10%,SO2 0或0.008%,N2为平衡气体,接触时间为0.03g·s·ml-1(GHSV=30000h-1)下对催化剂的活性进行了考察.实验结果发现,当贵金属Pd在B位部分替代Mn时,替代量x=0.01时的催化剂对于催化氧化分解NO反应具有最高活性.另外,在LaMn0.99Pd0.01O3催化剂上负载2%Ag也明显提高了催化剂的活性.而且LaMn0.99Pd0.01O3和2%Ag/LaMn0.99Pd0.01O3催化剂尽管抗水性能不好,但却具有较强的抗SO2性能.  相似文献   

5.
采用柠檬酸盐法合成出La0.6Sr0.4Co0.8Fe0.2O3钙钛矿复合氧化物超细粉料,考查了各种影响溶胶与凝胶的形成以及合成粉料晶体结构与颗粒形态的因素,并确定了最佳的合成条件。研究了烧成温度对La0.6Sr0.4Co0.8Fe0.2O3电导率的影响,发现1200℃是最合适的烧成温度。研究结果表明,在室温~900℃范围内,样品的电导率在600℃附近出现峰值(~103S·cm-1),在低温段样品的导电行为符合小极化子导电机制,不同烧成温度的样品的导电活化能基本一致(5.31~5.79kJ·mol-1)。与常规固相合成法相比,柠檬酸盐法合成的La0.6Sr0.4Co0.8Fe0.2O3具有更高的烧结活性和电导率。  相似文献   

6.
汽车尾气中 CO, HC, NOx,硫化物及其颗粒粉尘严重危害人们身体健康和大气环境,是大气环境的主要污染源之一.目前,尾气净化是其减排的最主要方式.汽车尾气催化剂的发展经历了几代的研究,一直以来广泛采用 Pt, Pd和 Rh等贵金属,但因其资源匮乏,价格昂贵,容易被 S和 P中毒,因此人们逐渐将目光投向非贵金属催化剂的研发.钙钛矿复合氧化物因具有独特的物理化学性质以及灵活的“化学剪裁”特性而在材料研究等领域颇受青睐,有望成为贵金属催化剂的替代品.一般而言,催化剂的比表面积越大,表面活性位点越多,其催化活性越高,且会明显降低起燃温度.目前,一些制备工艺,如水热法、共沉淀法、微乳液法和硬模板法,虽可在一定程度上提高催化剂的比表面积,但却存在费时、耗能及制备工艺复杂等缺点.因此,如何简单有效地制备出大比表面积的钙钛矿型催化剂依然是一个难题.本文以合成的分级多孔δ-MnO2微球为模板,采用熔盐法制备出球状多孔 La1-xSrxMn0.8Fe0.2O3(0≤x≤0.6)钙钛矿氧化物,研究了球状多孔钙钛矿氧化物的形成过程和合适的制备温度,以及 B位 Fe3+掺杂量为20%时 A位 Sr2+掺杂量对钙钛矿催化剂结构和催化活性的影响.采用 X射线粉末衍射、扫描电子显微镜、透射电子显微镜、N2吸附-脱附、傅里叶红外光谱(FT-IR)和 X射线能谱(XPS)等方法对催化剂进行了表征.在固定床石英管反应器上评价了催化剂催化 CO氧化活性及稳定性,采用气相色谱联接氢火焰离子化检测器检测了产物和反应物的组成.结果表明,以分级多孔δ-MnO2微球为模板,采用熔盐法在450oC反应4 h制备出的球状多孔 La1-xSrxMn0.8Fe0.2O3(0≤x≤0.6)钙钛矿氧化物具有良好的结晶性、较大的比表面积(55.73 m2/g)和孔体积(0.37 cm3/g).其球状多孔结构的形成可分为两个阶段:原位形成钙钛矿相和纳片表面析出钙钛矿晶粒及钙钛矿晶粒的再生长.另外, FT-IR光谱表明, Fe3+和 Sr2+成功进入 A, B位.同时, CO转化曲线表明, B位 Fe3+的掺杂量为20%时, A位 Sr2+的掺杂量高于30%时可以明显改善催化剂催化 CO氧化活性: La1-xSrxMn0.8Fe0.2O3(0≤x≤0.3)的T50和T90分别在180和198oC左右;而 La0.55Sr0.45Mn0.8Fe0.2O3和 La0.4Sr0.6Mn0.8Fe0.2O3的T50均低于125oC; La0.55Sr0.45Mn0.8Fe0.2O3的T90为181oC,而 La0.4Sr0.6Mn0.8Fe0.2O3却仍低于125oC. XPS结果则证明,较高的催化活性得益于 La0.4Sr0.6Mn0.8Fe0.2O3表面存在较多的 Mn4+、氧空位及吸附氧.最后, La0.55Sr0.45Mn0.8Fe0.2O3和 La0.4Sr0.6Mn0.8Fe0.2O3的稳定性测试结果表明,采用熔盐法以δ-MnO2为模板在450oC焙烧4 h制备的多孔球状钙钛矿具有较好的催化稳定性.虽然催化剂制备工艺简单,周期短,但比表面积最大只有55.73 m2/g,为硬模板法的1/2,因此提高比表面积将是今后研究的方向.  相似文献   

7.
陈银飞  王占龙  张泽凯 《催化学报》2009,30(12):1233-1237
 采用固相反应法合成了钙铝石材料 12SrO•7Al2O3, 并以此作为涂层制备了堇青石蜂窝陶瓷型 La0.8Sr0.2MnO3 整体催化剂, 在不同温度 (850~1 050 oC) 下对该催化剂进行了热处理, 并采用 N2 吸附-脱附、X 射线衍射和扫描电镜等手段对其进行了表征, 考察了其催化甲基丙烯酸甲酯燃烧反应的活性. 结果表明, 12SrO•7Al2O3 作为涂层明显改善了整体催化剂的热稳定性, 在 850 oC 下焙烧 6 h 后, 含有 12SrO•7Al2O3 涂层的整体催化剂在 260 oC 即可将甲基丙烯酸甲酯完全转化. 12SrO•7Al2O3 涂层可避免 La0.8Sr0.2MnO3 活性组分与堇青石的接触, 减轻了活性组分在催化剂表面的烧结, 有利于保持 La0.8Sr0.2MnO3 活性组分的晶体结构和分散度, 提高整体催化剂的活性和热稳定性.  相似文献   

8.
贵金属对钴基催化剂上肉桂醛选择加氢反应的影响   总被引:5,自引:0,他引:5  
 研究了贵金属改性的Co/γ-Al2O3催化剂上的肉桂醛选择加氢反应.结果表明,通过Pt,Pd和Ru贵金属改性,提高了催化剂的活性,但只有Pt改性的催化剂具有较高的选择性.w(Pt)<0.5%时,催化剂的活性随着Pt含量的增加呈直线升高,当w(Pt)=0.5%时,催化剂活性可提高近5倍,但催化剂的选择性变化很小.XRD结果表明,催化剂经还原后,γ-Al2O3上的钴主要为α-Co0.TPR结果表明,Pt的加入提高了Co3O4的还原性能,且Pt含量越高,Co3O4的还原温度越低.XPS结果表明,Pt改性的催化剂样品,其Co3O4大部分被还原为Co0.由于Pt与Co具有协同效应,故Pt改性的Co/γ-Al2O3催化剂既具有较高的活性,又具有很高的选择性.  相似文献   

9.
 用自燃烧法制备了钙钛矿型La0.8Sr0.2FeO3催化剂.用H2-TPR考察了催化剂表面的氧消耗过程,用程序升温表面反应(TPSR)研究了甲烷与催化剂表面氧物种的反应,用在线质谱脉冲反应和甲烷/氧切换反应研究了催化剂的晶格氧选择氧化甲烷制合成气.结果表明,催化剂上存在两种氧物种,无气相氧存在时,强氧化性氧物种首先将甲烷氧化为CO2和H2O;而后提供的氧化性较弱的晶格氧具有良好的甲烷部分氧化选择性,可将甲烷氧化为合成气CO和H2(选择性可达95%以上).在900℃下的CH4/O2切换反应结果表明,甲烷能与La0.8Sr0.2FeO3中的晶格氧反应选择性地生成CO和H2,失去晶格氧的La0.8-Sr0.2FeO3能与气相氧反应恢复其晶格氧.在合适的反应条件下,用La0.8Sr0.2FeO3催化剂的晶格氧代替分子氧按Redox模式实现甲烷选择氧化制合成气是可能的.  相似文献   

10.
采用柠檬酸-溶胶凝胶法制得钙钛矿型复合氧化物La0.8Ce0.2Mn1-xCuxO3(x=0.2,0.3,0.4),La0.8Sr0.2Mn0.6Cu0.4O3,La0.8Ce0.1Sr0.1Mn0.6 Cu0.4 O3,并采用X射线衍射(XRD)、扫描电镜(SEM)、比表面积(BET)、X射线光电子能谱(XPS)对其进行表征,测试了复合氧化物对CO+NO的催化活性。结果表明:La0.8Ce0.1Sr0.1Mn0.6Cu0.4O3催化活性最好,150℃时CO转化率91.8%,300℃时NO转化率100%;对于La0.8Ce0.2Mn1-xCuxO3(x=0.2,0.3,0.4),比表面积和颗粒的大小及分散度是影响催化活性的主要因素;对于La0.8Ce0.2Mn0.6Cu0.4O3,La0.8 Sr0.2 Mn0.6 Cu0.4 O3,La0.8 Ce0.1 Sr0.1 Mn0.6 Cu0.4 O3,催化剂的组成是影响催化活性的关键因素。  相似文献   

11.
用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.  相似文献   

12.
Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.  相似文献   

13.
In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.  相似文献   

14.
The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.  相似文献   

15.
The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.  相似文献   

16.
KMnO4-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.  相似文献   

17.
The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.  相似文献   

18.
A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.  相似文献   

19.
Zhanhui Yang  Shiyi Yang  Jiaxi Xu 《Tetrahedron》2017,73(23):3240-3248
Regiospecific and direct imidation of the methyl C(sp3)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.  相似文献   

20.
A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号