Active‐center equilibrium in Ziegler–Natta butadiene polymerization

The Ziegler–Natta‐catalyzed polymerization of 1,3‐butadiene was investigated at a low aluminum alkyl/cobalt (Al/Co) ratio using two different soluble catalyst systems: cobalt(II) octanoate/diethylaluminum chloride/water and cobalt(II) octanoate/methylaluminoxane/tert‐butyl chloride. When the active‐center concentration was determined by the number‐average molecular weight technique, it was found that the percentage of active cobalt depended on the Al/Co ratio. Subsequently, an equilibrium reaction was proposed to be Co + 2Al ? CoAl₂, where Co is cobalt(II) octanoate, Al is either of the aluminum alkyl‐activator species, and CoAl₂ is the active catalyst. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2256–2261, 2001     

Effect of epitaxial growth on the formation of the cobalt catalysts of the Fischer-Tropsch synthesis

Mixed oxides Co_xAl_yO₄ with different Al/Co ratios applied as supports for the catalysts of the Fischer-Tropsch synthesis were prepared using the solid-state chemical reaction. The Co_xAl_yO₄ supports were prepared by modifying gibbsite with various cobalt salts (acetate, nitrate, and basic carbonate). The use of basic cobalt carbonate gives the Co(20%)/Co_xAl_yO₄ catalyst, which provides an increased yield of hydrocarbons C₅₊ and a decreased methane content compared to the impregnation catalyst Co(30%)/Al₂O₃. The introduction of small amounts of rhenium additives makes it possible to enhance the yield of hydrocarbons C₅₊ (179 g m⁻³) and also to increase the selectivity with respect to the C₅–C₁₈ fraction. The introduction of basic cobalt carbonate into the support, most likely, creates favorable conditions for the epitaxial growth of the precursor of the active phase. Dedicated to Academician G. A. Abakumov on the occasion of his 70th birthday. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 9, pp. 1856–1860, September, 2007.     

具有双孔径分布的介孔C-Al2O3-TiO2纳米复合材料的合成及其红外发射率

以嵌段共聚物F127 (PEO₁₀₆PPO₇₀PEO₁₀₆, M_W=12600)为模板剂, 异丙醇铝和钛酸四丁酯为金属源, 低分子量的酚醛树脂为碳源, 通过溶胶-凝胶三元共组装法合成了具有双孔径分布的C-Al₂O₃-TiO₂纳米复合材料.用X射线衍射(XRD)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)及N₂吸附-脱附对该复合材料进行结构表征. 结果显示, 当铝钛原子的摩尔比为1:10 时, 对应的纳米复合材料具有较好的有序介孔结构, 其双孔径分别为3.9和6.5 nm, 比表面积可达259 m²·g^-1, 孔容0.37 cm³·g^-1. 以三元乙丙橡胶(EPDM)为粘结剂, 与介孔纳米复合材料混合制备涂层. 通过调节复合材料中铝钛摩尔比和涂层厚度, 红外发射率在0.450-0.617之间可调.     

The role of precursors in the structure of SiO2-Al2O3 sols and gels by the sol-gel process

Binary sols and gels of SiO₂-Al₂O₃ were prepared using tetraethyl orthosilicate and each of four aluminum compounds; aluminum di (sec-butoxide) ethylacetoacetic ester chelate (AC), aluminum nitrate nonahydrate (AN), aluminum formoacetate (AF), and boehmite sol (BS) made from aluminum i-propoxide. The structure and the evolution of the Si-O-Al bonds in SiO₂-Al₂O₃ sols and gels were investigated by ²⁷Al nuclear magnetic resonance (NMR), Infrared absorption spectra, DTA, and X-ray diffraction. The formation of Si-O-Al bonds differs depending on the aluminum compounds used as raw materials. The ratio of Al(IV) to {Al(IV) + Al(VI)} is related to the microstructural homogeneity of the gels. When AC is used as a raw material, the Si-O-Al bonds are formed in the sol state and resultant gel shows good microstructural homogeneity. In case of AN, the Si-O-Al bonds are not formed either in the sol or the wet gel state. The bonds are formed by drying the gel before heat-treatment temperature reaches 300 400°C, resulting in good microstructural homogeneous gel. When AF is used, the Si-O-Al bonds are formed in the sol state but the ratio of Al(IV) to {Al(IV) + Al(VI)} is lower than when using AC. Microstructural homogeneity of the gel is ranked between AC or AN and BS. Using BS, the Si-O-Al bonds are not formed in the sol solution, and the change in the coordination number of the gel is similar to that of boehmite gel. The Microstructural homogeneity of the gel is the worst among the BS gels, which were prepared by using the four aluminum raw materials.     

Preparation of Co–Al and Ni–Al layered double hydroxide thin films by a sol–gel process with hot water treatment

Using hot water treatment of sol–gel derived precursor gel films, Co–Al and Ni–Al layered double hydroxide (LDH) thin films were prepared. The precursor gel films of Al₂O₃–CoO or Al₂O₃–NiO were prepared from cobalt or nickel nitrates and aluminum tri-sec-butoxide using the sol–gel method. Then, the precursor gel films were immersed in a NaOH aqueous solution of 100 °C. Nanocrystallites of Co–Al and Ni–Al LDH were precipitated with the hot water treatment with NaOH solution. The largest amounts of nanocrystals were obtained with a solution of pH = 10 for Co–Al LDH, and with that of pH = 9 for Ni–Al LDH. X-ray diffraction measurements confirmed that this process formed CO₃ ²⁻ intercalated LDHs. Both Co–Al and Ni–Al LDH thin films were confirmed to work as electrodes for electrochemical devices by cyclic voltammogram measurements.     

钛、铝和玻璃上TiO2光催化膜的失活研究

采用浸渍提拉法，在平行条件下制备了钛、铝和玻璃载体上的TiO₂膜TiO₂ / Ti、TiO₂ / Al和TiO₂ / G，利用X射线光电子能谱(XPS)、原子力显微镜(AFM)和光催化降解实验等手段对膜样品进行了表征和活性评价。实验结果表明，在铝和玻璃基材上制膜时发生了显著的基材元素溢出，使各膜样品的化学组成不同，同时TiO₂粒子和膜表面形貌也因前驱物烧结行为不同而差异较大。TiO_{2相似文献}   

Effect of support and cobalt precursors on the activity of Co/AlPO4 catalysts in Fischer–Tropsch synthesis

Cobalt supported on amorphous aluminum phosphate (Co/AlPO₄) catalysts were prepared by the impregnation method using three different cobalt precursors such as cobalt nitrate, acetate and chloride to elucidate the activity of Fischer–Tropsch synthesis. The use of AlPO₄ as a support for cobalt-based catalysts exhibits better catalytic performance during FTS reaction than the corresponding Co/Al₂O₃ catalyst. TPR results also suggest that the reducibility of the catalysts varies with the nature of cobalt precursors employed during the impregnation on AlPO₄ support. The Co/AlPO₄ catalyst prepared from cobalt nitrate shows higher CO conversion and C₈+ selectivity than the others due to the facile formation of homogeneous cobalt particles with proper electronic characters and high reducibility. Interestingly, all Co/AlPO₄ showed a growth of filamentous carbon initiated from the large mobile cobalt particles during the reaction. The differences in catalytic properties of Co/AlPO₄ are mainly attributed to the cobalt particle size, reducibility with different electronic states of metallic cobalt, pore diameter of AlPO₄ and formation of filamentous carbon.     

富氧条件下Co/ZSM-5催化剂对C_3H_8选择还原NO_x的性能

采用多种物理化学手段研究了在模拟的轻型柴油车尾气中不同Co担载量及Cu掺杂的Co/ZSM-5催化剂的Co组分分散状态、可还原性、NO吸附脱附性质对C3H8选择性催化还原NOx性能的影响。结果表明,浸渍法制备的Co/ZSM-5催化剂上既有外表面上的Co3+和Co2+物种,也有孔内的Co2+离子。富氧条件下Co/ZSM-5催化剂上C3H8选择性催化还原NOx的活性主要与ZSM-5载体孔外表面分散的CoOx物种中的钴离子可还原能力和NO吸附脱附性能密切相关。Co/ZSM-5催化剂上适宜的Co担载量约为4.0wt%,低担载量时随Co担载量增加,表面CoOx物种中钴离子可还原能力增强,C3H8选择性催化还原NOx的低温转化活性增加;高担载量时,随Co担载量增加,单位Co离子的NO吸附量的减少以及催化剂表面活性中心数的减少,导致了Co/ZSM-5催化剂NOx的转化率和催化剂比速率(k)的下降。孔外表面Co3O4晶体的存在使催化剂表面产生较强的NO吸附,并在高温时有利于C3H8的氧化燃烧,使C3H8选择性催化还原NOx的活性降低。     

Synthesis and characterization of metal substituted AlxCr1−x(acetylacetonate)3 single-source precursors for their application to MOCVD of thin films

A detailed study, involving the synthesis of a single-source precursor containing two metal ions sharing the same crystallographic site, has been undertaken to elucidate the use of such a single-source precursor in a CVD process for growing thin films of oxides comprising these two metals, ensuring a uniform composition and distribution of metal ions. The substituted complexes Cr_1−xAl_x(acac)₃, where acac = acetylacetonate, have been prepared by a co-synthesis method, and characterized using UV–Vis spectroscopy, TGA/DTA measurements, and single crystal X-ray diffraction at low temperature. All the studied compositions crystallize in the monoclinic space group P2₁/c with Z = 4 in the unit cell. It was observed that the ratio (Al:Cr) of the site occupancy for the metal ions, obtained from single crystal refinement, is in agreement with the results obtained from complexometric titrations. All the solid state structures have the metal in an octahedral environment forming six-membered chelate rings. M–O acac bond lengths and disorder in the terminal carbon have been studied in detail for these substituted metal–organic complexes. One composition among these was chosen to evaluate their suitability as a single-source precursor in a LPMOCVD process (low-pressure metal–organic chemical vapour deposition) for the deposition of a substituted binary metal oxide thin film. The resulting thin films were characterized by X-ray diffraction, scanning electron microscopy, and infrared spectroscopy.     

富氧条件下Co/ZSM-5催化剂对C3H8选择还原NOx的性能

采用多种物理化学手段研究了在模拟的轻型柴油车尾气中不同Co担载量及Cu掺杂的Co/ZSM-5催化剂的Co组分分散状态、可还原性、NO吸附脱附性质对C₃H₈选择性催化还原NO_x性能的影响。结果表明,浸渍法制备的Co/ZSM-5催化剂上既有外表面上的Co³⁺和Co²⁺物种,也有孔内的Co²⁺离子。富氧条件下Co/ZSM-5催化剂上C₃H₈选择性催化还原NO_x的活性主要与ZSM-5载体孔外表面分散的CoO_x物种中的钴离子可还原能力和NO吸附脱附性能密切相关。Co/ZSM-5催化剂上适宜的Co担载量约为4.0wt%,低担载量时随Co担载量增加,表面CoO_x物种中钴离子可还原能力增强,C₃H₈选择性催化还原NO_x的低温转化活性增加;高担载量时,随Co担载量增加,单位Co离子的NO吸附量的减少以及催化剂表面活性中心数的减少,导致了Co/ZSM-5催化剂NO_x的转化率和催化剂比速率（k）的下降。孔外表面Co₃O₄晶体的存在使催化剂表面产生较强的NO吸附,并在高温时有利于C₃H₈的氧化燃烧,使C₃H₈选择性催化还原NO_x的活性降低。     

Thermal decomposition of cobalt nitrato compounds: Preparation of anhydrous cobalt(II)nitrate and its characterisation by Infrared and Raman spectra

The thermal decomposition of Co(NO₃)₂·6H₂O (1) as well as that one of NO[Co(NO₃)₃] (Co(NO₃)₂·N₂O₄) (2) was followed by thermogravimetric (TG) measurements, X-ray recording and Raman and IR spectra. The stepwise decomposition reactions of 1 and 2 leading to anhydrous cobalt(II)nitrate (3) were established. In N₂ atmosphere, cobalt oxides are finally formed whereas in H₂/N₂ (10% H₂) cobalt metal is produced. Rapid heating of cobalt(II)nitrate hexahydrate causes melting (formation of a hydrate melt) and therefore side reactions in the hydrate melt by incoupled reactions and evolution/evaporation of different species as, e.g., HNO₃, NO₂, etc. In case of larger amounts in dense packing in the sample container, the formation of oxo(hydoxo)nitrates is possible at higher temperature. For 2, its thermal decomposition to 3 was followed and its decomposition mechanism is proposed.     

LiCoO2梯度包覆LiNi0.96Co0.04O2电极材料的电化学性能

镍钴酸锂(LiNi0.8Co0.2O2)与目前商业用锂离子电池正极材料钴酸锂(LiCoO2)相比,具有成本低、实际比容量高和环境友好等优势。但LiNi0.8Co0.2O2的充放循环性能还有待提高,对其进行阳离子掺杂或表面修饰可以改善其电化学性能,这方面的研究已经成为热点。Fey等人[1]用溶胶凝胶法制     

Hydrotalcite-derived Co-containing mixed metal oxide catalysts for methanol incineration

The Co–Mg–Al mixed metal oxides were prepared by calcination of co-precipitated hydrotalcite-like precursors at various temperatures (600–800 °C), characterised with respect to chemical (AAS) and phase (XRD) composition, textural parameters (BET), form and aggregation of cobalt species (UV–vis-DRS) and their redox properties (H₂-TPR, cyclic voltammetry). Moreover, the process of thermal decomposition of hydrotalcite-like materials to mixed metal oxide systems was studied by thermogravimetric method combined with the analysis of gaseous decomposition products by mass spectrometry. Calcined hydrotalcite-like materials were tested as catalysts for methanol incineration. Catalytic performance of the oxides depended on cobalt content, Mg/Al ratio and calcination temperature. The catalysts with lower cobalt content, higher Mg/Al ratio and calcined at lower temperatures (600 or 700 °C) were less effective in the process of methanol incineration. In a series of the studied catalysts, the best results, with respect to high catalytic activity and selectivity to CO₂, were obtained for the mixed oxide with Co:Mg:Al molar ratio of 10:57:33 calcined at 800 °C. High activity of this catalyst was likely connected with the presence of a Co–Mg–Al spinel-type phases, containing easy reducible Co³⁺ cations, formed during high-temperature treatment of the hydrotalcite-like precursor.     

Thick Fe2O3, Fe3O4 films prepared by the chemical solution deposition method

Fe₂O₃, Fe₃O₄ films have been prepared from Fe(OCH₂CH(CH₃)₂)₃–(CH₃)₂CHCH₂OH–2.2′-diethanola- mine (DEA)–poly(vinylpyrrolidone) (PVP) solutions by the spin-(SC) and dip-coating (DC) technique on SiO₂ and Si substrates. The maximum film thickness achieved without crack formation has been increased by incorporation of PVP (relative molecular weights 40000 and 360000) into the precursor solution. The stability of the precursor solutions was remarkably increased by addition of DEA. Compact, dense, and crack-free Fe₂O₃ films with thicknesses 900 nm (DC), 450 nm (SC), have been obtained via single-step deposition cycle. Higher-molecular-weight PVP has been more effective in increasing the thickness. The minimum concentration of DEA, which results in pronounced increase of solutions stability, is about R _P (n(DEA)/n(Fe) = 0.1). The high content of carboneous residue in the pyrolysed Fe₂O₃ films promotes the formation of Fe₃O₄ films via reduction in a gas flow of H₂/N₂ gas mixture. Microstructure, surface morphology, and magnetic properties of the films have been also investigated using SEM, AFM, and SQUID, respectively.     

SILAR法制备化学计量CuInS2薄膜

在室温下，以不同c_Cu/c_In的CuCl₂和InCl₃混合溶液作为阳离子前驱体，Na₂S水溶液为硫源，利用连续离子层吸附反应法(SILAR)在玻璃基底上制备了CuInS₂薄膜。XRD结果表明，当c_Cu²⁺/c_In³⁺在1～1.5范围内均可形成具有黄铜矿结构的CuInS₂薄膜。SEM观察到随c_Cu²⁺/c_In³⁺的升高，薄膜表面颗粒长大并出现团簇聚集。通过XPS测定薄膜表面的化学组成证明当c_Cu²⁺/c_In³⁺=1.25时，CuInS₂薄膜接近其标准的化学计量组成。此时薄膜的吸收系数大于>10⁴ cm^-1，禁带宽度E_g为1.45 eV。     

Reforming of CH4 with CO2 over Co/Mγ-Al oxide catalyst

A series of Co/Mg–Al oxide samples,CoMgAl-x(x=(Mg+Co)/Al molar ratio of 1–5),were prepared by the self-combustion method followed by H2reduction.The catalytic performance and stability of the samples were studied in dry reforming of CH4.XRD and H2-TPR characterization results showed that the reduced CoMgAl-x samples mainly consisted of solid solution and spinel phases with cobalt particles.The spinel phases contained Co3O4 and Con Mg1-n Al2O4(0≦n≦1)varying with the(Mg+Co)/Al ratio.The effect of (Mg+Co)/Al molar ratio on the catalytic behavior was investigated in detail and CoMgAl-3 exhibited the highest catalytic activity and stability among the catalysts studied.     

Preparation of LiNiO2 and LiM y Ni1- y O2 (M=Co,Al) films by electrostatic spray deposition

Syntheses of LiNiO₂, LiCo_0.5Ni_0.5O₂, and LiAl_0.25Ni_0.75O₂ as thin films were carried out by electrostatic spray deposition (ESD) onto a gold substrate. Single-phase LiNiO₂ film was obtained using a precursor solution of Li(OCOCH₃)+Ni(OCOCH₃)₂/ethanol, and by heating the deposit at 700 °C under an oxygen stream. In the case of cobalt or aluminum doping, Co(NO₃)₂/ethanol or Al(NO₃)₃/ethanol were added to the precursor solution in a given ratio. X-ray diffractometry revealed that all films had a crystal structure of space group R3ˉm; a=2.879, c=14.197 ? for LiNiO₂; a=2.844, c=14.152 ? for LiCo_0.5Ni_0.5O₂; a=2.855, c=14.148 ? for LiAl_0.25Ni_0.75O₂ (in hexagonal setting). Although these products were highly porous, it was observed that the average film thickness of LiNiO₂ increased almost proportionally with the deposition time. Electrochemical measurements (cyclic voltammetry, charge/discharge measurement at a constant current) were carried out in organic solutions of LiClO₄ (1 mol dm⁻³ LiClO₄/propylene carbonate+ethylene carbonate). The results indicated that thin films fabricated by ESD were electrochemically active for lithium ion extraction/insertion. The effect of cobalt or aluminum doping on the voltammograms is also described. Received: 1 April 1998 / Accepted: 23 July 1998     

A template self-assembly strategy to synthesize free-standing TiO2-MO (M = Mg, Co, Ni, Cu or Zn) colloidal films

A series of binary free-standing colloidal films, TiO₂-MO (M = Mg, Co, Ni, Cu and Zn) have been synthesized via a self-assembly technology, utilizing sodium dodecyl sulfonate (SDS) as template and the mixture of titanium butoxide and MCl₂ as precursor. X-ray diffraction (XRD) and transmission electron microscope (TEM) have been employed to characterize TiO₂-MO samples. Results show that TiO₂-MO films are mainly composed by well-ordered nanostructures (e.g. mesoporous particles and lamellar pieces) and more importantly, the increased Ti(OC₄H₉)₄ precursor have significant effect on modifying the as-synthesized nanostructures. A structural model based on SDS micellar template, the complex metallic oxide precursor and charge-density matching between the template and precursor has been proposed. Remarkably, this template self-assembly method has a potential to design a variety of functional multicomponent materials with high-ordered nanostructures, such as high gas sensing SnO₂-ZnO films.     

Crystallization of textured PbTiO3 films deposited from gels

Sol-gel processed PbTiO₃ thin films have been deposited by spin coating onto different subtrates; Si[111], Si/Al, Si/SiO₂/Cr/Pt, MgO[100], SrTiO₃[100] and sapphire. Interactions between the substrate and PbTiO₃ films after heat treatment have been studied by X-ray diffraction and Rutherford Back Scattering. When deposited onto sapphire and Si[111], PbTiO₃ films exhibit a preferred orientation with (101) perpendicular to the substrate. These films become oriented along (100) onto MgO and (001) onto SrTiO₃[100] substrates. A strong channelling effect is observed by the RBS technique when the film is oriented along the c axis on SrTiO₃[100] suggesting that these films are epitaxially grown. The diffusion of metal atoms during the thermal treatment gives rise to the formation of lead silicate on Si[111] substrates. As a result a pyrochlore phase is formed. Lead titanate films on Si/SiO₂/Cr/Pt and Si/Al substrates are polycrystalline and do not exhibit any texture.     

Laser assisted selective chemical metalization of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> films

Thick aluminum oxide films are prepared on Al plates by anodizing. On the ceramic surface thus obtained a very thin Ag film is deposited via vacuum thermal evaporation. The Ag/Al₂O₃/Al samples prepared are irradiated by Nd:YAG laser through a suitable metal mask in order to remove the top metal film in the exposed areas. Thus, a negative silver image of the copied mask is obtained. Further, the samples are processed in Ni electroless chemical bath activated by the rest of silver. All processing steps are studied by scanning electron microscopy (SEM). EDS X-ray mapping is applied to study the final distribution of Al and Ni in the processed areas. In addition, the DC conductivity of the fabricated Ni wires obtained is measured. The proposed new method for selective chemical deposition of electroconductive Ni onto laser microstructured Ag/Al₂O₃/Al samples is simple, versatile and not restricted to the metal/ceramic system studied as well as to the electroless deposited metal.