Miscible blends of zinc-neutralized sulfonated polystyrene and poly(2,6-dimethyl 1,4-phenylene oxide)

Zinc-neutralized sulfonated polystyrene ionomers (ZnSPS) and poly(2,6-dimethyl 1,4-phenylene oxide) homopolymer (PXE) form miscible blends up to at least 7.8 mol % sulfonation, as measured by thermal and mechanical criteria. The addition of an equal weight of PXE raises the glass transition temperature of ZnSPS by 40–50°C. However, this miscibility is not achieved by eradicating the microdomain structure present in ZnSPS, even though the PXE coils are considerably larger than the spacings between ionic aggregates. Small-angle x-ray scattering indicates that while the average interaggregate spacing is roughly the same in ZnSPS and its 50/50 blend with PXE at a given sulfonation level, the extent of phase separation is reduced upon PXE addition, indicating that more ionic groups are dispersed in the matrix. Factors influencing miscibility in the ZnSPS/PXE materials and related blends are discussed.     

Drawing by solid-state coextrusion of blends of atactic and isotactic polystyrene with poly(2,6-dimethyl-1,4-phenylene oxide)

Atactic polystyrene (aPS)/poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) and isotactic polystyrene (iPS)/PPO compatible blends of varied composition were subjected to solid-state coextrusion. The efficiency of drawing, orientation, and crystallinity development were studied as a function of composition and draw ratio. The efficiency of drawing, as measured by elastic recovery, is high for coextrusion at temperatures ?40°C above the glass transition temperature of the particular blend. The maximum attainable draw ratio for the blends decreased with increasing PPO concentration; the highest blend draw ratio attained was 6.5 for 25 wt % PPO. The orientation on drawing, as measured by birefringence, increased with draw but decreased with increasing PPO component at the same draw ratio. When PPO was <50% in iPS/PPO blends, iPS crystallized on draw. The morphology of drawn blends was studied by electron microscopy and wide-angle x-ray scattering.     

Chain orientation in polystyrene/poly(2,6-dimethyl-1,4-phenylene oxide) blends

The differential orientation of polymer chains has been measured in polystyrene (PS)/poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) compatible blends. Density measurements are reported as a function of binary blend composition at 23°C. Drawing was performed by solid-state coextrusion. PS/PPO blend compositions of 90/10 and 75/25 were drawn within sandwiches of polyethylene at 145°C and isotactic polypropylene at 155°C, i.e. at ca. 25°C above the glass transition temperatures of the two blends. The change in Fourier-transform infrared dichroisms on drawing these blends was measured at 906 and 1190 cm^?1, corresponding to predominantly PS and PPO, respectively. The orientation of PS and PPO was observed as a function of draw ratio λ in the range 1–5; orientations increased with λ for both PS and PPO in both blends but to different degrees. Both polymers decreased in orientation with increasing PPO content. Annealing with fixed ends showed that the PPO chains disorient more slowly than those of PS. All binary systems were found to be amorphous and compatible.     

Thermal degradation and stabilization of poly(2,6-dimethyl-1,4-phenylene oxide)

Thermal degradation and stabilization of poly(2,6-dimethyl-1,4-phenylene oxide) have been examined in air in the range 100–400°. Plots of weight-average molecular weight vs time are linear, confirming random chain scission. The breakdown process has also been studied by DTA and TGA. It was concluded that thermal analysis alone was insufficient to characterize the degradation fully so the degradation products were determined qualitatively using i.r. and NMR spectroscopy. The heats of activation for the systems have been calculated and a stabilization mechanism by bis(1-phenyl-3-α-pyridyl triazeno)Cu(II) chelate has been postulated.     

Photosensitized and photostabilized oxidation of poly(2,6-dimethyl- 1,4-phenylene oxide) with metal isopropylxanthates

This work describes the results of the Cd(II) isopropylxanthate-stabilized and Mn(III) isopropylxanthate-sensitized photo-oxidation of poly(2,6-dimethyl-1,4-phenylene oxide) film in air at low temperatures (?10 to 80°). The oxidation was followed by light scattering, potassium ferri-oxalate actinometry and by measuring gel formation. The weight-average molecular weight, degree of degradation, rate of scission of links, energy of activation and quantum yield of the process depend on several factors, e.g. temperature, xanthate concentration. Various oxygen-containing groups (hydroperoxides, carbonyls, etc.) are formed in the polymer. For the determination of the content of these groups, iodometry and spectroscopy were applied. The initially present or photo-induced hydroperoxides are directly responsible for subsequent oxidative reactions which occur during 254-nm irradiation. The absorption spectra of the degraded materials in the u.v. and i.r. regions were also studied to substantiate a possible mechanism of the oxidation process.     

Radiation-induced grafting of N-isopropylacrylamide onto the brominated poly(2,6-dimethyl-1,4-phenylene oxide) membranes

A novel thermo-sensitive switching membrane has been prepared by radiation-induced simultaneous grafting N-isopropylacrylamide (NIPAAm) onto brominated poly(2,6-dimethyl-1,4-phenylene oxide) BPPO. In order to attain a high grafting degree, the effects of dose, dose rate, concentration of NIPAAm, concentration of inhibitor Cu²⁺, membrane thickness and solvents were investigated. The grafting process was characterized by FTIR spectroscopy and the highest grafting degree obtained was 7.87%. The thermo-sensitive property of the grafted membrane was measured by water flux (20–48 °C). The results showed that the grafted membrane could respond instantly to environmental temperature changes, and there was a sharp change around the lower critical solution temperature as it is normally seen in PNIPAAm hydrogel.     

Thermal and photochemical oxidation of 2,6-dimethylphenyl phenyl ether: A model for poly(2,6-dimethyl-1,4-phenylene oxide)

The oxygenation of 2,6-dimethylphenyl phenyl ether (I) at 260°C has resulted in the formation of 4-methylxanthone (II), 2-hydroxy-3-methylbenzophenone(III), 2-phenoxy-3-methylbenzaldehyde (IV), 2-phenoxy-3-methylbenzoic acid (V), 2-phenoxy-3-methylbenzyl o-cresotinate (VI), 2-phenoxy-3-methylbenzyl alcohol (VII), and 2-phenoxy-3-methylbenzyl 2-phenoxy-3-methylbenzoate (VIII), The photochemical oxidation at 75° produced compounds II, III, IV, VII, and VIII. Oxidation of poly(2,6-dimethyl 1,4-phenylene oxide) film at 200°C and photochemically at 50°C produced a carbonyl band at ca. 1730 cm^?1. The gel content of the photochemically aged film could be significantly reduced and the 1730 cm^?1 peak in the thermally aged specimen could be moved to longer wavelength by base treatment. The isolation of compound VIII in both processes with the model compound and the results with the polymer allows us to propose an ester group as a crosslinking unit in thermally and photochemically aged polymer film.     

Modification of Poly(2, 6-dimethyl-1,4-phenylene Oxide): Phosphorylation Studies

Side chain bromination of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) was carried out by using N-bromosuccinimide followed by phosphorylation of the bromo derivative with triethyl phosphite. Optimum conditions for minimum gel formation have been established. The products have been characterized by 'H-NMR and IR studies. Thermal behavior was investigated by thermogravimetry and differential scanning calorimetry in an air nitrogen atmosphere. Phosphorylated PPO starts to lose weight at 200°C, but the char yield increases with an increase in the phosphorus content of the polymer.     

Polymer-Polymer interactions via analog calorimetry. 1—blends of polystyrene with poly(2,6-dimethyl-1,4-phenylene oxide)

Analog calorimetry is used as a tool to study the interaction of polystyrene, PS, with poly(2,6-dimethyl-1,4-phenylene oxide), PPO, and with poly(1,4-phenylene oxide). Electrostatic charge calculations were used as a guide to divide polymer repeat units and analogs into groups. A mean-field binary interaction model was used to cvaluate group interaction energies. The enthalpic interaction energy for the blend of PS-PPO obtained from this study is −1.35 ± 0.19 cal/cm₃, which is in good agreement with values obtained from neutron scattering. The results indicate that electronic rearrangements between the phenyl ring and substituted methyl groups in PPO have a large influence on the interaction with polystyrene. © 1996 John Wiley & Sons, Inc.     

Poly(2,6-diphenyl-1,4-phenyl oxide): Characterization by gel-permeation chromatography,light scattering,and solution viscosity

Ten unfractionated poly(2,6-diphenyl-1,4-phenylene oxide) samples were examined by gel permeation chromatography (GPC) and intrinsic viscosity [η] at 50°C in benzene, by intrinsic viscosity at 25°C in chloroform, and by light scattering at 30°C in chloroform. The GPC column was calibrated with ten narrow-distribution polystyrenes and styrene monomer to yield a “universal” relation of log ([η]M) versus elution volume. GPC-average molecular weights, defined as M?gpc = \documentclass{article}\pagestyle{empty}\begin{document}$\Sigma w_i [\eta ]_i M_i /\Sigma w_i [\eta ]_i$\end{document}, w_i denoting the weight fraction of polymer of molecular weight M_i, were computed from the GPC and [η] data on the polyethers. The M?GPC were then compared with the weight-average M?_w from light scattering. The intrinsic viscosity (dl/g) versus molecular weight relations for the unfractionated poly(2,6-diphenyl-1,4-phenylene oxides) determined over the molecular weight range 14,000 ≤ M?_w ≤ 1,145,000 are log [η] = ?3.494 + 0.609 log M?_w (chloroform, 25°C) and log [η] = ?3.705 + 0.638 log M?_w (benzene, 50°C). The M?_w(GPC)/M?_n(GPC) ratios for the polymers in the molecular weight range 14,000 ≤ M?_w ≤ 123,000 approximate 1.5 according to computer integrations of the GPC curves with the use of the “universal” calibration and the measured log [η] versus log M?_w relation. The higher molecular weight polymers (326,000 ≤ M?_w ≤ 1,145,000) show slightly broadened distributions.     

Phase-separation phenomena in solutions of poly(2,6-dimethyl-1,4-phenylene oxide). I. Thermodynamic parameters of solutions in toluene

New experimental data have been collected on thermodynamic properties of solutions of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) in toluene. The Flory–Huggins interaction parameters g have been determined from light scattering measurements. These values are in agreement with values obtained by osmotic measurements at low concentrations and they allow the calculation of a melting point curve which fits the experimental melting points. No liquid–liquid phase separation can be calculated, as was concluded in a preceding paper. Spinodals could not be detected by light scattering or DSC-measurements. This also indicates that liquid–liquid phase separation does not occur. The phase separation on cooling of a PPO-toluene solution is thus believed to be a crystallization phenomenon.     

Blends of organosilicon polymers with polystyrene and poly(2,6-dimethyl-1,4-phenylene oxide)

Blends of organosilicon polymers with polystyrene, PS, and poly(2,6-dimethyl-1,4-phenylene oxide), PPE, were investigated by transmission electron microscopy and differencial scanning calorimetry. Blends with poly(tetramethylsilphenylenesiloxane), PTMPS, showed a morphology characterized by globular domains dispersed in the organic matrix. An apparent homogeneous system was observed when poly(dimethylsilphenylene), PDSP, was mixed with PPE. A crystalline phase was found in samples with a higher PDSP content. The morphology of PS/PDSP blends with low PDSP content showed a dendritic phase dispersed in the PS-rich matrix. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2609–2616, 1997     

Effect of molecular weight and temperature on physical aging of thin glassy poly(2,6-dimethyl-1,4-phenylene oxide) films

The effects of polymer molecular weight and temperature on the physical aging of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) is examined. Gas permeability and refractive index were monitored during the aging process for PPO film samples at three aging temperatures below the glass transition temperature. Comparisons between the two samples of PPO that differ widely in molecular weight reveal an insignificant difference, which support the notion that above a critical molecular weight range there is little influence on aging rate. Increased temperature, over the limited range of 35–55 °C, results in higher aging rates for films made from both PPO materials. The rate of aging decreases strongly with increasing film thickness over the range examined, ∼0.4–25 μm. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1390–1398, 2007     

Conformational behaviour of poly(2,6-dimethyl-1,4-phenylene oxide) in solution—I: Intrinsic viscosity as a function of temperature

Intrinsic viscosities [η] of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) solutions have been measured as a function of temperature between 60 and 25°C. The solvents were toluene and trichloroethene. In both solvents, the [η]-T curve exhibited a point of inflection in the range 45-35°. This phenomenon is explained as a conformational transition, which is possibly involved in the nucleation process of the solution crystallization of PPO. Assuming constancy of the coil expansion factor α_η and the solvent draining over the whole temperature interval, a slight increase of characteristic parameter C_α, with decreasing temperature has been calculated.     

Ternary upper-critical-solution-temperature behavior in a blend system comprising poly(2,6-dimethyl-1,4-phenylene oxide), poly(4-methyl styrene), and polystyrene

 Upper-critical-solution-temperature (UCST) behavior in a ternary blend of poly(2,6-dimethyl-1,4-phenylene oxide), poly(4-methyl styrene), and polystyrene is reported. The as-cast ternary blend is immiscible at ambient conditions and comprises two different phases, and, however, turns into a miscible system above the “clarity point” ranging from 160 to 300 °C for different ternary compositions. The maximum clarity point is labeled as the UCST for the ternary system, which is about 295 °C. Above the clarity point, the originally immiscible ternary blend turned into one miscible phase. Owing to the thermodynamic UCST behavior and kinetic hindrance, the immiscible ternary polymer blend can be locked into a pseudo-miscible state if it is heated to a temperature above the clarity point followed by a rapid-cooling processing scheme. The quenched ternary blend can remain in a pseudo-miscible state as long as the service temperature does not exceed the glass-transition temperature of the blend. Received: 17 July 2001 Accepted: 3 October 2001     

Chemical modification of poly(2,6-dimethyl-1,4-phenylene oxide) by bromination-alkynylation

The chemical modification of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) by bromination of the aromatic ring, followed by displacement of bromine with substituted acetylenes, has been investigated. This pathway leads to a series of novel copolymers containing substituted alkynes on the aromatic ring. The degree of bromination and alkynylation, determined by ¹H-NMR, was in the range of 20–85 and 15–80%, respectively. ¹³C-NMR and FT-IR unambiguously elucidated the structure of the alkynylated polymers. Finally, thermal properties and permeation properties of substituted PPO to carbon dioxide, methane, oxygen, and nitrogen are reported. © 1994 John Wiley & Sons, Inc.     

The high-temperature degradation of poly(2,6-dimethyl-1,4-phenylene ether)

The thermal degradation of poly(2,6-dimethyl-1,4-phenylene ether) has been investigated to 1000°C in an inert atmosphere. X-ray diffraction, thermogravimetric analysis, and differential scanning calorimetry were employed to study the physical changes in the polymer, and vapor-phase chromatography, infrared spectroscopy, and mass spectrometric thermal analysis were used to elucidate the chemical aspects of the degradation process. It was found that degradation occurs in two steps: (1) a rapid exothermic process occurs between 430 and 500°C, leading to the evolution of phenolic products, water, and a black, highly crosslinked residue, and (2) a slower, char-forming process occurs above 500°C, characterized by the evolution of methane, carbon monoxide, and hydrogen. The chars formed in process 2 were found by x-ray analysis to be amorphous. The infrared spectrum of a sample heated to 510°C is nearly identical with that of the starting polymer, indicating that oxidative reactions are not important in the first process. The data for the low-temperature process are consistent with a thermal degradation scheme based on the radical-redistribution reaction of polyphenylene ethers and/or the degradation of o-benzylphenols formed by the thermal rearrangement of o-methyl diphenyl ethers. The char-forming process is best explained by simultaneous operation of the Szwarc mechanism of toluene pyrolysis, producing hydrogen and methane and reactions that cleave the aromatic rings and produce carbon monoxide.     

Protection of poly(2,6-dimethyl-1,4-phenylene oxide) against u.v. irradiation

The photo-oxidative degradation and stabilization of poly(2,6-dimethyl-1,4-phenylene oxide) films have been examined in the temperature range 263–313 K in air with u.v. light of 253.7 nm. The changes in weight-average molecular weight, quantum efficiencies, carbonyl index, hydroperoxide concentration and i.r. spectra have been followed in the absence and presence of the stabilizer. The heats of activation of the systems have been calculated and the mechanism of stabilization has been postulated. A saturation limit in photostabilization of the polymer was achieved beyond 0.6 wt% of zinc di-n-hexyl dithiophosphate.     

Single crystals of poly(2,6-dimethyl-1,4-phenylene)oxide

Summary Poly(2,6-dimethyl-1,4-phenylene)oxide crystals obtained from 0.1%-pinene solutions by isothermal growth at temperatures from 80–90 as well as 100 °C, were investigated by optical and X-ray diffraction techniques. A study has been made by differential scanning calorimetry in order to measure the melting point, glass transition and melting point depression temperatures of mixtures of the polymer with-chloro-naphthalene.The densities of the dry mats of single crystals were measured by a flotation method.

---

Zusammenfassung Poly(2,6-dimethyl-1,4-phenylen)oxid Kristalle, die aus 0,1% igen-Pinen-Lösungen durch isothermes Wachstum bei Temperaturen von 80–90 sowie 100 °C erhalten wurden, wurden optisch und röntgenographisch untersucht. Mit der Differential-scanning-Kalorimetrie ergaben sich die Werte des Schmelzpunkts, der Glastemperatur und der Schmelzpunktdepressionen von Mischungen des Polymeren mit-Chlornaphthalin. Die Dichten der trockenen Matten aus Einkristallen wurde mit der Flotationsmethode gemessen.

     

Depolymerization of poly(2,6-dimethyl-1,4-phenylene oxide) under oxidative conditions

Depolymerization of an engineering plastic, poly(2,6-dimethyl-1,4-phenylene oxide) (PPO), was accomplished by using 2,6-dimethylphenol (DMP) under oxidative conditions. The addition of an excess amount of DMP to a solution of PPO in the presence of a CuCl/pyridine catalyst yielded oligomeric products. When PPO (M(n)=1.0x10(4), M(w)/M(n)=1.2) was allowed to react with a sufficient amount of DMP, the molecular weight of the product decreased to M(n)=4.9x10(2) (M(w)/M(n)=1.5). By a prolonged reaction with the oxidant, the oligomeric product was repolymerized to produce PPO essentially identical to the starting material, making the oligomer useful as a reusable resource. During the depolymerization reaction, an intermediate phenoxyl radical was observed by ESR spectroscopy. Kinetic analysis showed that the rate of the oxidation of PPO was about 10 times higher than that of DMP. These results show that a monomeric phenoxyl radical attacks the polymeric phenoxyl to induce the redistribution via a quinone ketal intermediate, leading to the substantial decrease in the molecular weight of PPO, which is much faster than the chain growth.