Dosage du baryum dans l''eau et les liquides biologiques par spectrometrie d''emission avec source plasma haute frequence

Determination of barium in water and biological fluids by emission spectrometry with an inductively-coupled plasma

An emission spectrometric method is described for the determination of barium in water urine and blood with an inductively-coupled plasma. The method is highly selective, reproducible, and sensitive. The limits of detection are 0.06 μg l^-1 in water, 0.25 μg l^-1 in urine, 0.6 μg l^-1 in blood. For thirteen healthy subjects, the barium content was 4.3 μg l^-1 (s = 1.4) in urine and less than 1 μg l^-1 in blood. For a case of accidental poisoning, the content was 260 μg Ba l^-1 in blood and 280 μg Ba l^-1 in urine.     

Electrochemistry at carbon fibers : Part 1. Characteristics of the Mercury Film Carbon Fiber Electrode in Differential Pulse Anodic Stripping Voltammetry

Carbon fibers are proposed as a support electrode for a mercury film electrode. The response of these electrodes is evaluated for use in differential pulse anodic stripping voltammetry. The mercury film is deposited in situ in aqueous solution and used to quantify cadmium in solutions of cadmium salts and organo cadmium compounds in the 1–10 μg l^-1 (ppb) concentration range. The good resolution and extremely low background current obtained allow a limit of detection at 0.04 μg Cd l^-1.     

Evaluation of ammonia as diluent for serum sample preparation and determination of selenium by graphite furnace atomic absorption spectrometry

A method for the determination of total selenium in serum samples by graphite furnace atomic absorption spectrometry was evaluated. The method involved direct introduction of 1:5 diluted serum samples (1% v/v NH₄OH+0.05% w/v Triton X-100^®) into transversely heated graphite tubes, and the use of 10 μg Pd+3 μg Mg(NO₃)₂ as chemical modifier. Optimization of the modifier mass and the atomization temperature was conducted by simultaneously varying such parameters and evaluating both the integrated absorbance and the peak height/peak area ratio. The latter allowed the selection of compromise conditions rendering good sensitivity and adequate analyte peak profiles. A characteristic mass of 49 pg and a detection limit (3s) of 6 μg 1⁻¹ Se, corresponding to 30 μg l⁻¹ Se in the serum sample, were obtained. The analyte addition technique was used for calibration. The accuracy was assessed by the determination of total selenium in Seronorm™ Trace Elements Serum Batch 116 (Nycomed Pharma AS). The method was applied for the determination of total selenium in ten serum samples taken from individuals with no known physical affection. The selenium concentration ranged between 79 and 147 μg l⁻¹, with a mean value of 114±22 μg l⁻¹.     

A hydride generation atomic fluorescence spectrometric procedure for selenium determination after flow injection on-line co-precipitate preconcentration

A flow injection (FI) on-line preconcentration procedure for ultra-trace inorganic selenium was developed with detection by atomic fluorescence spectrometry. Selenium (IV) is co-precipitated with lanthanum hydroxide and collected on a PTFE beads packed column, the precipitate is afterwards dissolved with hydrochloric acid followed by hydride generation with reduction by tetrahydroborate. A thorough scrutiny was made for chemical variables and FI parameters. With a sampling volume of 3.4 ml, quantitative retention of selenium (IV) was obtained, along with an enrichment factor of 11 and a sampling frequency of 38 h^− 1. The detection limit, defined as 3 times the blank standard deviation (3σ), was 5 ng l^− 1. The precision was characterized by a RSD value of 1.2% (at the 0.5 μg l^− 1 level, n = 11). The enrichment factor was further enhanced to 20 along with a detection limit of 3 ng l^− 1, with a sample loading volume of 6.8 ml. The procedure was validated with certified reference materials and biological samples. It was also applied to the speciation of inorganic selenium in surface waters.     

Quantitative analysis of fluid inclusions in evaporites by ion chromatography

Natural salt minerals often contain inclusions of saturated salt solutions with diameters from 1 to> 100 μm. With the quantification of the composition of the fluid inclusions, the origin and metamorphism of the salt rocks can be interpreted. Hence, these data are important concerning the long-term safety of underground repositories in salt rocks [1]. For the extraction of the solutions in fluid inclusions with diameters 300 μm, an optical precision instrument was developed. For the simultaneous determination of Cl⁻, Br⁻, SO₄²⁻, Li⁺, Na⁺, K⁺, Mg²⁺ and Ca²⁺ two ion chromatographic systems with conductivity detection for cations and anions and additional photometric detection for Br⁻ were used. To prevent column overload, the Cl concentration must be less than 50 μg/ml in the measuring solution. The extracted samples (volumes> 0.1 μl) are diluted with demineralized water by a factor of 1 · 10⁴ (20-μl sample loops). The practical limit of determination for the measured elements is 0.01–0.3 μg/ml in the measuring solutions. By calculation of the anion and cation charge balance (molar equivalence), a relative error of <5% for the analysis of fluid inclusions was found.     

Electrochemiluminescence sensor using tris(2,2′-bipyridyl)ruthenium(II) immobilized in Eastman-AQ55D–silica composite thin-films

An electrochemiluminescence (ECL) sensor with good long-term stability and fast response time has been developed. The sensor was based on the immobilization of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) into the Eastman-AQ55D–silica composite thin films on a glassy carbon electrode. The ECL and electrochemistry of Ru(bpy)₃²⁺ immobilized in the composite thin films have been investigated, and the modified electrode was used for the ECL detection of oxalate, tripropylamine (TPA) and chlorpromazine (CPZ) in a flow injection analysis system and showed high sensitivity. Because of the strong electrostatic interaction and low hydrophobicity of Eastman-AQ55D, the sensor showed no loss of response over 2 months of dry storage. In use, the electrode showed only a 5% decrease in response over 100 potential cycles. The detection limit was 1 μmol l⁻¹ for oxalate and 0.1 μmol l⁻¹ for both TPA and CPZ (S/N=3), respectively. The linear range extended from 50 μmol l⁻¹ to 5 mmol l⁻¹ for oxalate, from 20 μmol l⁻¹ to 1 mmol l⁻¹ for TPA, and from 1 μmol l⁻¹ to 200 μmol l⁻¹ for CPZ.     

Determination of mercury in saliva with a flow-injection system

A simple, fast and reliable method, with a low detection limit, has been developed for the determination of total mercury in saliva samples. The method uses a brominating reagent, followed by on-line addition of KMnO₄ at room temperature to convert organically bound mercury to inorganic mercury ions, and determines mercury by flow-injection cold-vapour atomic absorption spectrometry. Using the method described, complete recoveries of five mercury compounds from saliva were attained. Results obtained on real samples using the new method were comparable to that obtained using the established method with batch system. The detection limit of this method, based on three standard deviations of the blank, is 0.05 μg l⁻¹ Hg in a saliva sample of 500 μl. A sample throughput of 80 measurements per hour is possible with the method. The calibration curves are linear up to 20 μg l⁻¹ and the dynamic range extends to 40 μg l⁻¹ Hg. At a concentration of 1μg l⁻¹ mercury in saliva, the relative standard deviation is about 2% for 11 replicates; a total volume of 0.5 ml saliva is required for three replicates.     

Flow-injection chemiluminescence determination of chlortetracycline using on-line electrogenerated [Cu(HIO(6))(2)](5-) as the oxidant

A novel chemiluminescence (CL) flow system for the determination of chlortetracycline is described. It is based on the direct CL reaction of chlortetracycline and [Cu(HIO₆)₂]⁵⁻ in KOH medium. The unstable [Cu(HIO₆)₂]⁵⁻ was on-line electrogenerated by constant-current electrolysis. The CL intensity was linear with chlortetracycline concentration in the range of 0.1–100 μg ml⁻¹. The determination limit was 5.3×10⁻⁸ g ml⁻¹. The whole process could be completed in 1 min. The proposed method is suitable for automatic and continuous analysis, and has been applied satisfactorily to analysis of chlortetracycline in biological fluid.     

Determination of glyphosate by ion chromatography

An ion chromatography system for the determination of glyphosate was described. Ion chromatograph was carried out by suppressed conductivity detection (DX-100). The eluent contained 9 mmol l⁻¹ Na₂CO₃ and 4 mmol l⁻¹ NaOH. The detection limit was 0.042 μg ml⁻¹ (S/N=3). The relative standard deviation was 1.99% and the correlation coefficient of the calibration curve for area was 0.9995. The linear range was 0.042100 μg ml⁻¹. Common inorganic ion and organic acids did not interfere. The recovery was 96.4103.2%. The method was simple, rapid, reliable and inexpensive.     

Determination of nanomolar concentrations of phosphate in freshwaters using flow injection with luminol chemiluminescence detection

A simple and rapid flow injection (FI) method is reported for the determination of phosphate (as molybdate reactive P) in freshwaters based on luminol chemiluminescence (CL) detection. The molybdophosphoric heteropoly acid formed by phosphate and ammonium molybdate in acidic conditions generated chemiluminescence emission via the oxidation of luminol. The detection limit (3× standard deviation of blank) was 0.03 μg P l⁻¹ (1.0 nM), with a sample throughput of 180 h⁻¹. The calibration graph was linear over the range 0.032–3.26 μg P l⁻¹ (r²=0.9880) with relative standard deviations (n=4) in the range 1.2–4.7%. Interfering cations (Ca(II), Mg(II), Ni(II), Zn(II), Cu(II), Co(II), Fe(II) and Fe(III)) were removed by passing the sample through an in-line iminodiacetate chelating column. Silicate interference (at 5 mg Si l⁻¹) was effectively masked by the addition of tartaric acid and other common anions (Cl⁻, SO₄²⁻, HCO₃⁻, NO₃⁻ and NO₂⁻) did not interfere at their maximum admissible concentrations in freshwaters. The method was applied to freshwater samples and the results (26.1±1.1–62.0±0.4 μg P l⁻¹) were not significantly different (P=0.05) from results obtained using a segmented flow analyser method with spectrophotometric detection (24.4±4.45–84.0±16.0 μg P l⁻¹).     

Low-molecular-mass anion screening for forensic environmental analyses by capillary zone electrophoresis with indirect UV detection

A method for low-molecular-mass anion screening is described using a buffer composed of 5-sulfosalicylate (SS) as a visualizing ion, hexadimethrine bromide as an electroosmotic flow modifier and Tris as a pH buffer component, at pH 8.6. All ions with effective mobility higher than 2610⁻⁹ m² s⁻¹ V⁻¹ can be separated within 7.5 min under −30 kV. By using the moderately mobile SS (5410⁻⁹ m² s⁻¹ V⁻¹), not only the sensitivity of the detection is improved due to its high UV absorptivity, but also a smaller overall overloading effect is achieved. Meanwhile, the resolution of the high mobility ions, which is normally critical, remains almost the same as compared to a chromate buffer. With an electrokinetic injection, the limit of detection (LOD) of the common ions is 2–13 nM and the detection range is linear up to 0.5–3 μM. With a hydrostatic injection the LOD is 0.15–1 μM and the detection range is linear up to 25–200 μM. The identification of ions is performed by comparing the mobility of the ions with that of standards, taking the apparent and effective mobility of HCO₃⁻, which is normally present in the sample solution, as a reference.     

Speciation of iodate and iodide in seawater by non-suppressed ion chromatography with inductively coupled plasma mass spectrometry

A non-suppressed ion chromatography (IC) with inductively coupled plasma mass spectrometry (ICP-MS) has been developed for simultaneous determination of trace iodate and iodide in seawater. An anion-exchange column (G3154A/101, provided by Agilent) was used for the separation of iodate and iodide with an eluent containing 20 mM NH₄NO₃ at pH 5.6, which reduced the build-up of salts on the sampler and skimmer cones. The influences of competing ion (NO₃⁻) in the eluent on the retention time and detection sensitivity were investigated to give reasonable resolution and detection limits. Linear plots were obtained in a concentration range of 5.0–500 μg/L and the detection limit was 1.5 μg/L for iodate and 2.0 μg/L for iodide. The proposed method was used to determinate iodate and iodide in seawaters without sample pre-treatment with exception of dilution.     

Turbidimetric determination of sulphate in waters employing flow injection and lead sulphate formation

An analytical flow-injection procedure based on PbSO₄ colloidal formation is proposed as a turbidimetric determination of sulphate in natural waters. Ethanol-water was used as a medium in order to improve the sensibility of the method. Both chemical and flow variables as well as interfering species were studied. A detection limit of 0.3 μg SO²⁻₄ ml⁻¹ was found, and the analytical range (according to Beer's law) was 2–20 μg SO²⁻₄ ml⁻¹. The precision was better than 3% R.S.D. and the sample throughput was ca. 35 h⁻¹. The method, when compared with a standard methodology, gave good results when applied to water analysis.     

Silicon determination by inductively coupled plasma atomic emission spectrometry after generation of volatile silicon tetrafluoride

A method for the determination of silicon by inductively coupled plasma atomic emission spectrometry (ICP-AES) is described. The procedure is based on a discontinuous generation of volatile silicon tetrafluoride in concentrated sulphuric acid medium after injecting 125 μl of 0.1%, w/v sodium fluoride solution into 100 μl of the sample. The gaseous silicon tetrafluoride is fed directly into the ICP torch by a flow of 250 ml min⁻¹ Ar carrier gas. The calibration curve was linear up to at least 100 μg ml⁻¹ of Si(IV) and the absolute detection limit was 9.8 ng working with a solution volume of 100 μl. The relative standard deviation for six measurements of 10 μg ml⁻¹ of Si(IV) was 2.32%. The method was applied to the determination of silicon in water and iron ores.     

Flow-through fluorescence immunosensor for atrazine determination

A new flow-through fluoroimmunosensor for atrazine determination based on the use of protein A immobilized on controlled pore glass as immunoreactor is reported. The support, placed in the optical path of the flow cell, allows the ‘in situ’ quantification of atrazine by on-line antigen–antibody binding upon successive injections of both substances. The immunosensor has a detection limit of 2.1 μg l⁻¹, a sample speed of about 10 samples per hour, and provides high reproducibility both within-day (3.2% for 5 μg l⁻¹ and 2.2% for 30 μg l⁻¹) and between days. The optimum working concentration range was 2.1–50 μg l⁻¹. Possible interferences of other triazines like simazine, desethylatrazine (DEA) and desisopropylatrazine (DIA) were evaluated. Simazine and DIA were not cross-reactive; however, the cross-reactivity for DEA was CR=7.7%. The proposed immunosensor was successfully applied to the determination of atrazine in drinking water and citrus fruits.     

Design of two-dimensional biomimetic uranyl optrode and its application to the analysis of natural waters

A two-dimensional biomimetic optrode for the detection and quantification of uranium in natural waters was fabricated. The sensing element was designed by the inclusion of uranyl ion imprinted polymer particles into polymethyl methacrylate followed by casting a thin film on a glass slide without any plasticizer. The ion imprinted polymer material was prepared via covalent immobilization of the newly synthesised ligand 4-vinyl phenylazo-2-naphthol by thermal polymerization. Operational parameters such as pH, response time and the amount of sensing material were optimized. The response characteristics of the imprinted and the corresponding non-imprinted polymer inclusion optrodes of uranium were compared under optimum conditions. The imprinted polymer inclusion optrode responds linearly to uranium in the concentration range 0–1.0 μg mL⁻¹ with a detection limit of 0.18 μg mL⁻¹, which is much better than the solution studies using 4-vinyl phenylazo-2-naphthol (1.5 μg mL⁻¹). Triplicate determinations of 100 μg of uranium(VI) present in 250 mL of solution gave a mean absorbance of 0.018 with a relative standard deviation of 8.33%. The superior sensitivity of imprinted polymer inclusion optrode is exemplified by lower detection limits and broader dynamic range over non-imprinted polymer inclusion optrode. The developed imprinted polymer inclusion optrode was found to give stable and precise response for 3 months and can be used without any loss in sensitivity. The applicability for analysing ground, lake and tap-water samples collected in the vicinity of uranium deposits was successfully demonstrated.     

Simultaneous determination of total arsenic and total selenium in Chinese medicinal herbs by hydride generation atomic fluorescence spectrometry in tartaric acid medium

By HG-AFS, a new method was proposed for simultaneous determination of total arsenic and total selenium existed in the Chinese medicinal herbs in tartaric acid medium. The effects of analytical conditions and coexisting ions on the fluorescence signal intensity of analytes were investigated. The proposed method was provided with linear response ranges above 22 μg l⁻¹ for As and 44 μg l⁻¹ for Se, and the detection limits of 0.13 and 0.12 μg l⁻¹ were obtained for As and Se respectively. The recoveries of 93.8–96.1% for As and 95.3–99.1% for Se, and the precision of 1.2–3.8% and 2.4–5.3% (R.S.D., n = 8) respectively, were obtained via simultaneous determined four samples of Chinese medicinal herbs and three certified botanic reference materials successfully. The proposed method has the advantages of simple operation, high sensitivity and high efficiency.     

A label-free electrochemical immunosensor based on gold nanoparticles for detection of paraoxon

An electrochemical immunosensor for the direct determination of paraoxon has been developed based on the biocomposites of gold nanoparticles loaded with paraoxon antibodies. The biocomposites are immobilized on the glassy carbon electrode (GCE) using Nafion membrane. On the immunosensor prepared paraoxon shows well-shaped CV with reduction and oxidation peaks located −0.08 and −0.03 mV versus SCE, respectively. The detection of paraoxon performed at −0.03 mV is beneficial for guaranteeing sufficient selectivity. The amount of the biocomposite consisting gold nanoparticles loaded with antibodies and the volume of Nafion solution used for fabricating the immunosensor have been studied to ensure sensitivity and conductivity of the immunosensor. The immunosensor has been employed for monitoring the concentrations of paraoxon in aqueous samples up to 1920 μg l⁻¹ with a detection limit of 12 μg l⁻¹.     

Chemiluminescent determination of pyridoxine hydrochloride in pharmaceutical samples using flow injection

A chemiluminescent method using flow injection is described for the determination of pyridoxine hydrochloride. Its detection limit, linearity and reproducibility were examined. The method is based on the enhancing effect of pyridoxine hydrochloride on the chemiluminescence generated by the oxidation of luminol with hydrogen peroxide in aqueous potassium hydroxide and sodium oxalate. The proposed method is simple and inexpensive. The chemiluminescence intensity is a linear function of pyridoxine hydrochloride concentration over the range 10–250 μg ml⁻¹ with a detection limit of 6 μg ml⁻¹. The applicability of the method was demonstrated by the determination of pyridoxine hydrochloride in different tablet formulations and some dietary sources.     

Method development for the determination of lead in wine using electrothermal atomic absorption spectrometry comparing platform and filter furnace atomizers and different chemical modifiers

A method has been developed for the determination of lead in wine by electrothermal atomic absorption spectrometry without any sample preparation and calibration against aqueous standards, using 7.5 μg Pd as a chemical modifier. The results obtained for seven wines using the proposed method and an acid digestion procedure did not show any significant difference using a Student's t-test. Atomization in a transversally heated filter atomizer (THFA) was compared with atomization in a conventional transversally heated platform furnace. The former provided a 2.6-fold higher sensitivity, improving the characteristic mass from 34 to 12 pg and a 1.6-fold better limit of detection (0.3 μg L⁻¹ compared to 0.5 μg L⁻¹) for aqueous solutions using the same injection volume of 20 μL. However, the average precision, expressed as the relative standard deviation for the determination of lead in wine under routine conditions was improved from 4.6% with platform atomization to 0.6% in the THFA. The lead content found in seven arbitrarily chosen white and red wines, five from Brazil, one from Chile and one from Spain, ranged from 6 to 60 μg L⁻¹ Pb with an average content of 11.4 μg L⁻¹ Pb for the wines from South America.