Improvement of Sweep Efficiency by Alkaline Flooding for Heavy Oil Reservoirs

Severe viscous fingering during water flooding of heavy oil leaves a large amount of oil untouched in the reservoir. Improving sweep efficiency is vital for enhancing heavy oil recovery. This study presented a laboratory study for improving sweep efficiency by alkaline flooding in heavy oil Reservoirs. This included glass-etched micromodel flooding tests, one-dimensional flooding experiments and three-dimensional physical model study. The micromodel tests show that W/O droplet flow plays a prominent role in the alkaline flooding to improve sweep efficiency. There is a minimum alkaline concentration that generates the W/O droplet flow, and the W/O droplet flow is more obvious with the alkaline concentration increasing. A series of flood tests were conducted using 325 mPa · s, 2000 mPa · s, and 3950 mPa · s heavy oils to assess the effectiveness of W/O droplet flow in alkaline flooding for enhanced heavy oil recovery. The flood tests results demonstrate the considerable potential for improved heavy oil recovery by alkaline flooding, and moreover, the incremental oil recovery has been found to increase as the alkaline concentration increases. The result obtained in three-dimensional physical model study indicates that the sweep area can be greatly improved by the formation of W/O droplet flow in alkaline flooding.     

Dynamic Interfacial Tension Behavior of Water/Oil Systems Containing In situ-Formed Surfactants

Time-dependent interfacial tension (IFT) has been investigated for an interfacially reactive immiscible system composed of model-acidified oil and alkaline water. The acidified oil was composed of either lauric acid or linoleic acid dissolved in n-dodecane. Drop volume tensiometry was employed to measure the interfacial tension between the two phases. In the case of lauric acid, the IFT value was found to decrease sharply with increasing alkali concentration, even at low drop formation times. In the case of linoleic acid, the IFT decrease with the drop formation time was more gradual, especially at low alkali concentration. The rate of formation of the interfacial area was also found to be dependent on alkali concentration.     

Study on Influencing Factors of Chemical Flooding for Heavy Oil

Alkali and alkali/surfactant displacing agents are designed for two kinds of heavy oil. Results of emulsifying capacity, dynamic interfacial tension (IFT) and water-wet core flooding tests show that, although alkaline/surfactant systems exhibit better capacity in emulsification and IFT reduction, oil recovery values of alkaline/surfactant flooding are lower than those of alkaline flooding. Glass-etched micromodel tests further demonstrate that, when alkaline solution penetrates into the oil phase, water streams break into ganglia coating oil film. Water ganglia may be entrapped by narrow throats, consequently presenting a water-oil alternating slug flow. Similar water ganglia also appears in alkaline/surfactant flooding, however, water channeling along the pore surface occurs subsequently, resulting in its relatively lower oil recovery.     

配体交换色谱法测定草甘膦

建立了配体交换色谱测定草甘膦的方法.在自制的配体交换色谱柱上,以醋酸铜-醋酸水溶液为流动相,紫外(254 nm)检测,实现了草甘膦与双甘膦中间体的基线分离.考察了流动相中醋酸铜和醋酸的浓度,以及流动相流速对目标物分离的影响,确定了以0.2 mmol/L醋酸铜-醋酸水溶液为流动相,流速0.8 mL/min的优化色谱条件,并进行了系统适应性实验和方法学评价.结果表明:草甘膦与双甘膦之间的分离度Rs＞3,拖尾因子在0.8～1.0之间;在0.05～1.00 g/L范围内,草甘膦和双甘膦的线性相关系数分别为0 9998和0 9999; 回收率分别为102.2%和99.0%; 峰面积的RSD分别为0.14%和0.59%; 检出限分别为0 05和0.50 mg/L(S/N=3).     

Kinetic, mechanistic and spectral studies for the oxidation of sulfanilic acid by alkaline hexacyanoferrate(III)

The kinetics of oxidation of sulfanilic acid (p-aminobenzenesulfonic acid) by hexacyanoferrate(III) in alkaline medium was studied spectrophotometrically. The reaction showed first order kinetics in hexacyanoferrate(III) and alkali concentrations and an order of less than unity in sulfanilic acid concentration (SAA). The rate of reaction increases with increase in alkali concentration. Increasing ionic strength increases the rate but the dielectric constant of the medium has no significant effect on the rate of the reaction. A retarding effect was observed by one of the products i.e. hexacyanoferrate(II) (HCF(II)). A mechanism involving the formation of a complex between sulfanilic acid and hexacyanoferrate(III) has been proposed. The reaction constants involved in the mechanism are evaluated. There is a good agreement between the observed and calculated rate constants under different experimental conditions. Investigations at different temperatures allowed the determination of the activation parameters with respect to the slow step of the proposed mechanism.     

1,2,3-苯三氧基三乙酸的浮选抑制性能

抑制剂;1;2;3-苯三氧基三乙酸的浮选抑制性能     

Box-Behnken设计毛细管液相色谱法拆分α-氨基酸对映体的研究

将L-脯氨酸通过3-缩水甘油丙基三甲氧基硅烷键合到球型多孔硅胶基质上,制备了手性配体交换色谱固定相.采用高压匀浆法将制备的填料填充到毛细管柱中,在自组装的毛细管液相色谱仪上对3种α-氨基酸对映体进行了拆分.利用Box-Behnken设计对影响因素(流动相中乙腈的体积分数、中心离子Cu~(2+)的浓度、流速)进行优化,以最大保留时间和分离度为响应值,借助二次多元回归方程,建立了相应的数学模型.响应曲面图表明:DL-天冬酰胺在5%乙腈、5 mmol/L Cu~(2+)、流速0.139 μL/min,苏氨酸在10%乙腈、5 mmol/L Cu~(2+)、流速0.167 μL/min,丝氨酸在5%乙腈、7 mmol/L Cu~(2+)、流速0.167 μL/min的条件下均能得到基线分离.表明通过所制备的手性固定相,采用配体交换色谱模式可获得拆分DL-氨基酸的理想效果.     

高选择性高效液相色谱-电化学检测法测定丹参中5种酚类物质

发展了一种高灵敏度的高效液相色谱-电化学检测（HPLC-ECD）方法,用于丹参中5种酚类物质的定量分析。为了获得较高的检测灵敏度,对流动相的pH、缓冲溶液类型和浓度、有机相种类和梯度以及流速做了系统研究。在较低的pH（2.8）、较低的缓冲盐浓度（20 mmol/L NaH₂PO₄）和较缓的乙腈梯度下,以0.2 mL/min流速可为5种酚类的分离检测提供较好的分离度和较高的检测灵敏度。在获得优化的分离参数后,将其用于14批丹参药材中5种酚类物质的定量分析。结果表明,该方法可获得较好的回收率（>95%）、较宽的线性范围（高达4个数量级）、较好的重复性（RSD<4.01%）和较高的灵敏度（咖啡酸的LOQ低至1.5μg/L）。与紫外检测方法相比,ECD检测方法具有更高的选择性,可减少非抗氧化活性的物质的干扰。     

三元复合驱碱/表面活性剂/聚合物模拟原油乳状液稳定动力学特性

基于两相分离的乳状液稳定模型,研究了三元复合驱模拟原油乳状液稳定动力学特性;通过液膜强度和油水界面张力探讨了碱/表面活性剂/聚合物对模拟原油乳状液稳定动力学特性的影响机理。 结果表明,乳状液稳定模型可以很好的评价乳状液的稳定性,并得到乳状液的稳定动力学特性;碱浓度小于900 mg/L有利于乳状液的稳定,碱浓度大于900 mg/L不利于乳状液的稳定;表面活性剂和聚合物浓度的增加使得形成的模拟原油乳状液更加稳定;模拟原油乳状液的稳定作用主要是通过碱、表面活性剂降低油水界面张力并增加油水界面膜强度,聚合物通过提高界面膜强度实现的,三者存在协同效应。     

Analysis of insecticide thiacloprid by ion chromatography combined with online photochemical derivatisation and fluorescence detection in water samples

This study describes a novel application of ion chromatography coupled with post-column photochemically induced fluorimetry derivatisation in alkaline medium and fluorescence detection(IC-hv-FD) for the determination of neonicotinoid pesticide, thiacloprid. In an aqueous medium, this compound showed fluorescence with an excitation maximum at 236 nm and an emission maximum at 353 nm. The 10 mmol/L NaOH with 10%(v/v) acetonitrile solution pumped at flow rate of 1.0 mL/min was used for the chromatographic elution to isocratically separate thiacloprid on an Ion Pac1 AS 11(250 mm 4 mm i.d; 13 mm particle size, Dionex) anion-exchange column. The linear concentration range of application was 0.04–10.0 mg/L, with a relative standard deviation(RSD, n = 7) of 1.7%(for a level of 2.0 mg/L) and detection limit(LOD, S/N = 3) of 9.9 mg/L. The procedure was applied with satisfactory results to the analysis of thiacloprid in ground and lake water samples. Pesticide average spiked recoveries ranged between 95.5% and 114.0%.     

乙二胺硅胶材料对铜和锌离子的动态吸附

合成了胺基含量为1.35 mmol/g的乙二胺硅胶材料(EDA/SiO2),研究了EDA/SiO2对Cu2+和Zn2+的动态吸附及动态竞争吸附。结果表明,铜溶液流量和初始浓度对材料动态吸附性能有显著影响,随着溶液初始浓度的增大、流速的加快,穿透时间明显缩短。动态吸附实验结果符合Thomas模型,计算结果显示,铜溶液初始浓度由1.99 mmol/L增大至10.00 mmol/L时,模型平衡吸附容量q0从0.272 mmol/g增大至0.476 mmol/g,影响显著;流量对q0影响不显著。溶液流量和初始浓度对吸附速率常数kTh均有影响,随溶液流量增大、初始浓度的降低,速率常数值增大。在单一体系中,EDA/SiO2对Cu2+和Zn2+的工作吸附量分别为0.340和0.127 mmol/g,混合体系的吸附量均小于单一体系中的吸附量,并且对Zn2+的吸附量下降显著,表明EDA/SiO2对Cu2+的吸附能力强于Zn2+。6次循环实验表明,盐酸和氨水可对EDA/SiO2材料实现再生,再生后材料对铜的吸附容量和穿透时间的下降幅度不大,可重复使用。     

Determination of olive oil acidity by CE

In this work, a CE method for the determination of olive oil acidity was proposed. The method was based on an ethanolic extraction (at 60 degrees C) of the oil long-chain free fatty acids (LC-FFAs) components followed by CE determination in pH 6.86 phosphate buffer at 15 mmol/L concentration containing 4 mmol/L sodium dodecylbenzenesulfonate (SDBS), 10 mmol/L polyoxyethylene 23 lauryl ether (Brij 35), 2% v/v 1-octanol and 45% v/v ACN under indirect UV detection at 224 nm. Although this electrolyte promoted baseline separation of myristic acid (C14:0) (internal standard (IS)) and olive oil major components (palmitic acid (C16:0), oleic acid (C18:1c) and linoleic acid (C18:2cc)) in less than 8 min, after a few injections, the electropherogram profiles were severely altered (peak broadening, migration time shifts, etc.) and the current increased substantially. An adsorption study was conducted revealing that the dissolution of the capillary external polyimide coating during the electrophoretic run caused the detrimental effect. After removal of the capillary tip coating, ten consecutive injections could be performed without any disturbances and this simple procedure was, therefore, implemented during quantitative purposes. The reliability of the proposed method was further investigated by the determination of acidity of an extra virgin olive oil sample in comparison to the established methodology (AOCS method Ca 5a-40, alkaline volumetric titration (AVT)). No statistical differences were found within 95% confidence level. A % acidity of 0.39 +/- 0.02 was found for the olive oil sample under consideration.     

Ce(IV)-induced polymerization of allyl methacrylate with cotton cellulose

Ce(IV)-induced polymerization of allyl methacrylate (AMA) with cotton cellulose was investigated under a variety of conditions. Polymer add-on was directly related to AMA concentration. The same holds good for Ce(IV) ion concentration up to a certain concentration (30 mmol/L), after which it decreases. Polymer add-on was higher at 60 than at 50 and 70°C. A methanol/water mixture (20/80) offers the best medium for polymerization. Addition of nitric acid (up to 400 mol equivalent/L) or perchloric acid (up to 800 mol equivalent/L) to the polymerization system caused significant enhancement in polymer add-on. The reverse was the case with sulphuric acid irrespective of the concentration used. A comparison between polymer add-on values based on increase in weight and those based on estimated allyl double bonds indicated that the latter undergo partial homopolymerization.     

基于次血红素六肽的过氧化氢和葡萄糖灵敏比色方法

采用次血红素六肽(DhHP-6)催化H₂O₂氧化4-氨基安替吡啉-氯代苯酚显色体系,建立了测定H₂O₂和葡萄糖的方法。 研究了pH值、底物浓度和DhHP-6浓度对实验的影响,检测了比色方法的反应线性、稳定性、相关性和回收率。 在最佳反应条件下,DhHP-6在不同时间及温度条件下,活性要优于过氧化物酶(POD);DhHP-6催化H₂O₂ 的米氏常数(K_m)和最大反应速率(v_max)分别为0.171 mmo/L和4.22×10^-6 mol/s;H₂O₂响应的线性范围为0.39~25.0 mmol/L;高、中、低 3水平测定的变异系数(CV)和加标回收率分别在1.29%~2.16%和94.5%~101.1%之间;与葡萄糖商品试剂盒比较相关系数R²=0.9946;36例血液样品中的葡萄糖浓度在4.26~17.48 mmol/L之间。 与葡萄糖检测商品试剂盒之间的两组数据经统计差异不显著(P>0.05)。 该方法是一种简单、廉价、方便、灵敏的比色测定方法。     

Evaluation of porous graphitic carbon stationary phase for simultaneous preconcentration and separation of organic and inorganic selenium species in "clean" water systems

A high performance liquid chromatography procedure, based on porous graphitic carbon stationary phase, was evaluated for simultaneous on-line preconcentration and separation of organic and inorganic selenium species. Detection was achieved by inductively coupled plasma mass spectrometry with collision/reaction cell (ICP-CRC-MS). Different concentrations of formic acid were tested as mobile phase. A 240 mmol L(-1) concentration with pH adjusted to 2.6, allowed the separation of five species, i.e. selenite, selenate, selenomethionine, selenocystine and selenoethionine. On-line preconcentration of these five species was achieved when heptafluorobutyric acid was used as injection medium, inducing an enrichment of solutes at the top of the column which allowed large volumes (up to 1 mL) to be injected. Combining these injection conditions and 80Se monitoring with ICP-CRC-MS, detection limits between 2 and 8 ng (Se)L(-1), depending on the species, were obtained. Because of the extremely low detection limits obtained, the method was successfully applied to mineral waters.     

Effect of organic acid chain length on foam performance in a porous medium

We have systematically studied the effect of organic acid chain length on surface dilatational properties and foam flow performance in a porous medium. Surface dilatational properties were studied by oscillating drop module (ODM). ODM results in deionized water show that sufficient long chain length of organic acid is an essential requirement for high surface dilatational modulus. While, to various salinities, surfactant to acid ratio of achieving high surface dilatational modulus varies. Foam flow tests show that surface dilatational modulus has decisive effect on produced foam size, which partially determines foam flow pressure drop. Both surface dilatational modulus and surface tension determine foam flow pressure drop. Besides, surface loss modulus also contributes to pressure drop. Bulk foam tests show that addition of organic acids with proper chain length can enhance foam tolerance to oil significantly. Compared with alkane chain length, acid with longer chain has good ability in stabilizing foam. At last, foam flooding tests show that surface dilatational modulus and foam tolerance to oil play important roles in foam enhanced oil recovery.     

离子排斥色谱法测定生脉注射液中的有机酸

1引言生脉注射液是由红参、麦冬和五味子3种药材经提取后制成的灭菌水溶液,为国家中药保护品种,具有益气养阴,复脉固脱的功效。前期的分析实验表明,生脉注射液中含有有机酸类成分。根据生脉注射液的生产工艺和3种药材的的化学成分研究报道,分析生脉注射液中的有机酸主要来源于五味子。五味子含有柠檬酸、苹果酸、琥珀酸等多种有机酸成分。目前,有机酸的分析方法有气相色谱法[1]、高效液相色谱法[2]、毛细管电泳法[3]及离子色谱法[4]。这些方法专属[5]     

以L-酒石酸正己酯-硼酸配合物作为反相液相色谱手性流动相添加剂拆分5种β-受体阻滞剂

本文以L-酒石酸正己酯-硼酸配合物为手性流动相添加剂,建立了普萘洛尔、艾司洛尔、美托洛尔、比索洛尔、索他洛尔和阿替洛尔六种β-受体阻滞剂的反相高效液相色谱手性分离方法。对影响对映体分离的主要因素：L-酒石酸正己酯、硼酸浓度,缓冲溶液种类、浓度、pH值和有机改性剂-甲醇含量等进行了详细考察。最佳色谱条件为：Venusil MP-C18色谱柱（4.6 mm × 250 mm,5 μm）,流动相为15 mmol/L乙酸铵-甲醇（体积比为20: 80或30: 70,含60 mmol/L硼酸,70 mmol/L L-酒石酸正己酯,醋酸调节pH值6.00）,检测波长214 nm。在最佳分离条件下,五对对映体（普萘洛尔、艾司洛尔、美托洛尔、比索洛尔、索他洛尔）可以分别获得基线分离。     

Use of a Carbon Paste Electrode Modified with Spinel‐Type Manganese Oxide as a Potentiometric Sensor for Lithium Ions in Flow Injection Analysis

A potentiometric sensor constructed from a mixture of 25% (m/m) spinel‐type manganese oxide (lambda‐MnO₂), 50% (m/m) graphite powder and 25% (m/m) mineral oil is used for the determination of lithium ions in a flow injection analysis system. Experimental parameters, such as pH of the carrier solution, flow rate, injection sample volume, and selectivity for Li⁺ against other alkali and alkaline‐earth ions and the response time of this sensor were investigated. The sensor response to lithium ions was linear in the concentration range 8.6×10^?5–1.0×10^?2 mol L^?1 with a slope 78.9±0.3 mV dec^?1 over a wide pH range 7–10 (Tris buffer), without interference of other alkali and alkaline‐earth metals. For a flow rate of 5.0 mL min^?1 and a injection sample volume of 408.6 μL, the relative standard deviation for repeated injections of a 5.0×10^?4 mol L^?1 lithium ions was 0.3%.     

胶束电动毛细管色谱在柱富集和分离7种植物激素

利用胶束电动毛细管色谱在柱样品电堆积的预富集方法,以十二烷基硫酸钠胶束作准固定相,对七种植物激素进行了富集和分离。研究了各种分离条件的影响,并分别在高电渗流和聚丙烯酰胺涂层抑制电渗流条件下对植物激素进行在柱电堆积富集,各种植物激素的检出限比文献报道降低1～2个数量级。在最佳条件下对植物样品中的脱落酸进行了测定,其相对标准偏差为2．4％;回收率为75％。