pH-dependent mucoadhesion of a poly(N-isopropylacrylamide) copolymer reveals design rules for drug delivery

This study investigated the mucoadhesive property of a hydrophobically modified copolymer N-isopropylacryamide and glycidylacrylamide NIPAM-N-Gly-(C18)2 (NIPAM-Gly). Prior studies demonstrated that the interfacial properties of this copolymer are pH dependent and that the chains form strong hydrogen bonds at pH < 7 via the carboxylic acid side chains of the glycine moieties. Mucin interactions with the copolymer brushes were investigated by surface plasmon resonance and by direct force measurements. Mucin adsorption was determined as a function of pH, ionic strength, and mucin concentration. It adsorbs to the copolymer strongly at pH 5, but the adsorption decreases with increasing pH. The adsorbed amount is also ionic-strength dependent, decreasing with increasing monovalent salt concentrations at all pH values investigated. When compared with similar investigations with poly(ethylene oxide), these results provide insights into both the chemical characteristics and the solution conditions that determine the mucoadhesive properties of polymers.     

Competitive adsorption of neutral comb polymers and sodium dodecyl sulfate at the air/water interface

The interfacial behavior of aqueous solutions of four different neutral polymers in the presence of sodium dodecyl sulfate (SDS) has been investigated by surface tension measurements and ellipsometry. The polymers comprised linear poly(ethylene oxide) with low and high molecular masses (10(3) and 10(6) Dalton (Da), respectively), and two high molecular mass methacrylate-based comb polymers containing poly(ethylene oxide) side chains. The adsorption isotherms of SDS, determined by Gibbs analysis of surface tension data, are nearly the same in the presence of the high molecular mass linear polymer and the comb polymers. Analysis of the ellipsometric data reveals that while a single surface layer model is appropriate for films of polymer alone, a more sophisticated interfacial layer model is necessary for films of SDS alone. For the polymer/surfactant mixtures, a novel semiempirical approach is proposed to determine the surface excess of polymer, and hence quantify the interfacial composition, through analysis of data from the two techniques. The replacement of the polymer due to surfactant adsorption is much less pronounced for the high molecular mass linear polymer and for the comb polymers than for the low molecular mass linear polymer. This finding is rationalized by the significantly higher adsorption driving force of the larger polymer molecules as well as by their more amphiphilic structure in the case of the comb polymers.     

Well-packed chains and aggregates in the emission mechanism of conjugated polymers

We synthesized dialkoxy-substituted poly[phenylene vinylene]s (dROPPV-1/1, 0.2/1, and 0/1) consisting of two repeating units with different side-chain lengths (methoxy and 3,7-dimethyloctyloxy). These polymers can serve as a model system to clarify roles of aggregates (the sites with ground-state interchain interactions) and the independent chain segments in the well-packed chains (the chain segments that are compactly packed without interaction) in the emission mechanism of conjugated polymers. Due to the packing of polymer chains, films of all of these polymers are accessible to interchain excitations, after which excitons can re-form to result in delayed luminescence. Besides, some chains form aggregates so that the delayed luminescence is no more the ordinary single-chain emission but red-shifted and less structured. Not only the re-formation of these indirect excitons but also the aggregation of chains are facilitated in the polymers with short methoxy side groups, revealing that both packing and aggregation of chain segments require a short spacing between polymer chains. However, the incorporation of other side chains such as the 3,7-dimethyloctyloxy group to dROPPVs is necessary for the formation of aggregates because these long branched side chains can reduce the intrachain order imposed by the short methoxy groups, which accounts for the absence of aggregate emission in the well-studied poly[2,5-dimethoxy-1,4-phenylene vinylene]. This study reveals that the well-packed chains do not necessarily form aggregates. We also show that the photophysical properties and the film morphology of conjugated polymers can be deliberately controlled by fine-tuning of the copolymer compositions, without altering the optical properties of single polymer chains (e.g., as in dilute solutions).     

Surface forces and friction tuned by thermo-responsive polymer films

Thermo-responsive polymer films have enabled the development of various functional surfaces with switchable interfacial properties. Assessing the surface forces and friction on such films is of paramount importance. On the one hand, it allows us to extract a great deal of information on the interfacial properties of the films, e.g., adhesiveness and lubricity, and how they could be tuned using different stimuli. On the other hand, surface force measurements complement other thin-film analysis methods, e.g., ellipsometry, to better perceive the correlation between the molecular properties of the polymer chains and the interfacial properties of the film. On this basis, we will, herein, provide a concise review of some recent studies on surface forces and friction tuned by thermo-responsive polymer films. This outline comprises a summary of several research works addressing the effects of temperature, solvent composition, and salts on surface forces and friction. In the end, we briefly discuss a few select studies in which the regulation of surface forces by thermo-responsive polymers is examined with an emphasis on the potential applications.     

Géométrie de micelles à deux compartiments hydrophobes

We discuss a “comb block copolymer” with a hydrophilic backbone (N polar heads), Nf/2 side chains of type A, and Nf/2 side chains of type B. Imposing an area per head and a volume per side chain, we predict various conformations based on two spherical portions. In certain cases, two distinct conformations are permitted by this criterion: the best one should minimise the A/B interfacial energy. We also discuss “multiplets” (p polymers per double micelle) and “necklaces” (k double micelles for one polymer chain).     

Synthesis of ferrocene-grafted poly(p-phenylene-ethynylenes) and control of electrochemical behaviors of their thin films

New ferrocene-coated poly(p-phenylene-ethynylenes) (PPEs) with end capping groups of protected thiol were prepared by a palladium-catalyzed Sonogashira coupling reaction. Ferrocene groups were covalently attached to polymers A and B through ethylene oxide tethers and to polymer C through methylene tethers. Polymers A and B are soluble in common solvents such as tetrahydrofuran (THF), chloroform, methylene chloride, acetone, dimethylformamide (DMF), and dimethyl sulfoxide (DMSO), and polymer C is soluble in toluene, THF, chloroform, and methylene chloride. Polymers A-C display low quantum yield, caused by electron-transfer quenching of ferrocene groups as electron donors. The polymer thin films were prepared through incubation of gold electrodes in THF solutions containing the polymers for 2 days. Ferrocene in thin films of polymers A and B display significantly faster electron-transfer rate than that of polymer C. Hydrophilic ethylene oxide side chains of polymers A and B decrease formal potential of tethered ferrocene groups because of electron-donating effect from ethylene oxide side chains, which stabilizes the ferrocenium ion and leads to a cathodic shift of the redox wave.     

pH-responsive copolymer films by surface-catalyzed growth

We have engineered a new class of pH-responsive polymer films on gold surfaces by first developing a controlled, surface-catalyzed polymerization to prepare a copolymer film consistent with poly(methylene-co-ethyl acetate) and subsequently hydrolyzing the ester side chains to varying extents to yield carboxylic acids (denoted as PM-CO2H). When pH is increased, the acid groups become deprotonated or charged, dramatically increasing their water solubility and greatly altering the film properties. The carboxylic acid content within the copolymer film can be adjusted by changing the monomer concentration ratio used in the polymerization process or the length of time for the hydrolysis. We have designed PM-CO2H films to consist predominately (>95%) of polymethylene (PM) so that the film is hydrophobic in the uncharged state and, thereby, exhibits an extremely large pH-induced response in barrier properties once ionized. The effect of polymer composition on pH response was investigated by electrochemical impedance spectroscopy (EIS), reflectance-absorption infrared spectroscopy (RAIRS), and contact angle measurements. At a 1%-4% molar acid content, the copolymer film exhibits a 5 orders of magnitude change in its resistance to ion transport over 2-3 pH units. The pH at which this response begins can be tailored from pH 5 to pH 10 by decreasing the acid content in the film from 4% to 1%.     

Synthesis,characterization, and electroluminescence of fluorene and carbazole‐based blue light‐emitting polymers with different noncoplanar molecular architectures

In order to investigate the explicit optoelectronic variations of the photoluminescent polymer with sterically hindered side chains, three novel alternate polymers (P0, P1, and P2) based on fluorene and carbazole moieties were successfully synthesized through Suzuki coupling reaction. The molecular structures of the polymers were fully characterized by ¹H‐NMR, ¹³C‐NMR, elemental analysis, and gel permeation chromatograph, respectively. The photophysical properties, thermal stability, and energy band gaps of polymers P0, P1, and P2 were further examined through UV–vis absorption, photoluminescent spectra, differential scanning calorimetry, thermogravimetric analysis, and cyclic voltammetry. The experimental results indicated that the polymers took on wide band gaps of about 3.50 eV with deep blue emission in thin solid films. These polymers were found to show a high thermal stability with decomposition temperatures at 5% weight loss of the compounds in the range of 353–416 °C. Blue light‐emitting electroluminescent devices of the most branched polymer P2 with highest light‐emitting efficiency as emitting layers were characterized, which showed obviously improved spectral stabilities with respect to the parent polyfluorene materials. In conclusion, we have established an effective method to improve the spectral stabilities of polyfluorene material by synthesizing the zigzag‐shaped copolymer of fluorene and carbazole with sterically hindered pendant moieties of different molecular sizes. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis of double hydrophilic graft copolymer containing poly(ethylene glycol) and poly(methacrylic acid) side chains via successive ATRP

A well‐defined double hydrophilic graft copolymer, with polyacrylate as backbone, hydrophilic poly(ethylene glycol) and poly(methacrylic acid) as side chains, was synthesized via successive atom transfer radical polymerization followed by the selective hydrolysis of poly(methoxymethyl methacrylate) side chains. The grafting‐through strategy was first used to prepare poly[poly(ethylene glycol) methyl ether acrylate] comb copolymer. The obtained comb copolymer was transformed into macroinitiator by reacting with lithium diisopropylamine and 2‐bromopropionyl chloride. Afterwards, grafting‐from route was employed for the synthesis of poly[poly(ethylene glycol) methyl ether acrylate]‐g‐poly(methoxymethyl methacrylate) amphiphilic graft copolymer. The molecular weight distribution of this amphiphilic graft copolymer was narrow. Poly(methoxymethyl methacrylate) side chains were connected to polyacrylate backbone through stable C? C bonds instead of ester connections. The final product, poly[poly(ethylene glycol) methyl ether acrylate]‐g‐poly(methacrylate acid), was obtained by selective hydrolysis of poly(methoxymethyl methacrylate) side chains under mild conditions without affecting the polyacrylate backbone. This double hydrophilic graft copolymer was found be stimuli‐responsive to pH and ionic strength. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4056–4069, 2008     

Kinetics of pH response for copolymer films with dilute carboxylate functionality

We have investigated the effects of film composition and thickness on the rate of pH-induced response of a copolymer film containing predominately polymethylene with randomly distributed carboxylic acid side groups (denoted as PM-CO2H). These responsive films are prepared directly onto a gold electrode surface by surface-catalyzed polymerization and subsequent hydrolysis. We measured electrochemical impedance at fixed frequency (100 Hz) to monitor the barrier properties of the polymer film during a step change in pH. At a 1-3% molar acid content, the copolymer films exhibit a 2 order of magnitude change in impedance at 100 Hz when the contacting solution pH changes from 11 to 4 (or 4 to 11). For all films, the rate of protonation is slower than that of ionization, consistent with a more gradual transfer of protons through an increasingly hydrophobic film at the outermost nanometers during the protonation step. Increased acid content within the film accelerates both the rate of protonation and ionization. Thinner films (50 nm) with the same acid content show faster response rate in both directions, since water and ions have a shorter transfer path. A large and reversible pH response was obtained for all films studied, but selection of appropriate film composition and thickness can greatly influence the rate of response.     

Functional films of maleic anhydride copolymers under physiological conditions

Reactivity and swelling of nanometer films of alternating maleic anhydride copolymers were investigated in dependence on the kind of comonomer and molar mass of copolymer in aqueous solution at pH 7.4 and pH 3.0 in order to reveal their characteristics under physiological conditions. Fully hydrolyzed (maleic acid) chains of the copolymers with styrene, propene, and ethylene comonomers covalently bound to SiO2 substrates showed a "mushroom" swelling behavior at pH 7.4 with a layer thickness scaling of N3/5. Decreasing the environmental pH was found to induce a comonomer-dependent shrinking or collapse of the immobilized polymers due to the change in ionization. From the swelling kinetics of non-hydrolyzed chains, the time constants and characteristics of swelling and anhydride hydrolysis were determined and found to depend on the type of comonomer. The short- and long-term swelling kinetics [l approximately t and approximately ln(t)1/2] were found to be in agreement with theoretical models of polymer swelling, while at intermediate time scales enhanced swelling was observed due to hydrolysis reaction of maleic anhydride groups. The findings elucidate the variety of properties of maleic anhydride copolymer films under physiological conditions, which can advantageously be applied for biofunctionalization of different templates.     

Interfacial properties of free-standing poly(3-hexylthiophene) films

Using full atomistic classical molecular dynamics simulations, the interfacial properties of free-standing poly(3-hexylthiophene) (P3HT) films have been investigated. The orientations of different parts of the P3HT chain and the surface tensions of the films were calculated in a temperature range of 540 K-600 K. At the liquid/vacuum interface, the P3HT chain shows ordering by exposing hexyl groups at the interface, while the chain backbone lays flat with the thiophene ring preferentially tilt toward the surface. At the interface, the terminal methyl groups of hexyl side chains are in excess compared to the methylene groups or thiophene rings. The surface tension of P3HT in its melt state shows similar temperature dependence to that of polymers that have long alkyl side chains. The surface tension values are comparable to those polymers that expose methyl or methylene groups on the surface. The surface tension values determined for the melt state are lower than the experimental reported values for crystalline P3HT films, as expected.     

Macromolecular Recognition and Macroscopic Interactions by Cyclodextrins

Herein macromolecular recognition by cyclodextrins (CDs) is summarized. Recognition of macromolecules by CDs is classified as main‐chain recognition or side‐chain recognition. We found that CDs form inclusion complexes with various polymers with high selectivity. Polyrotaxanes in which many CDs are entrapped in a polymer chain were prepared. Tubular polymers were prepared from the polyrotaxanes. CDs were found to recognize side‐chains of polymers selectively. CD host polymers were found to form gels with guest polymers in water. These gels showed self‐healing properties. When azobenzene was used as a guest, the gel showed sol‐gel transition by photoirradiation. When ferrocene was used, redox‐responsive gels were obtained. Macroscopic self‐assembly through molecular recognition has been discovered. Photoswitchable gel association and dissociation have been observed.     

End-grafted low-molecular-weight PNIPAM does not collapse above the LCST

The interfacial properties of end-grafted temperature-responsive poly(N-isopropylacryamide) (PNIPAM) were quantified by direct force measurements both above and below the lower critical solution temperature (LCST) of 32 degrees C. The forces were measured between identical, opposing PNIPAM films and between a PNIPAM film and a lipid membrane. At the grafting densities and molecular weights investigated, the polymer extension did not change significantly above the LCST, and the polymers did not adhere. Below the LCST, the force-distance profiles suggest a vertical phase separation, which results in a diluter outer layer and a dense surface proximal layer. At large separations, the force profiles agree qualitatively with simple polymer theory but deviate at small separations. Importantly, at these low grafting densities and molecular weights, the end-grafted PNIPAM does not collapse above the LCST. This finding has direct implications for triggering liposomal drug release with end-grafted PNIPAM, but it increases the temperature range where these short PNIPAM chains function as steric stabilizers.     

Synthesis and radical ring‐opening polymerization of vinylcyclopropanes derived from amino acids with hydrophobic moieties

Six 1,1‐disubstituted vinylcyclopropanes (VCP) were synthesized from glycine and amino acids bearing hydrophobic moieties, l ‐alanine, l ‐valine, l ‐leucine, l ‐isoleucine, and l ‐phenylalanine. These VCP derivatives efficiently underwent radical ring‐opening polymerization to afford the corresponding polymers bearing trans‐vinylene moiety in the main chains and the amino acid‐derived chiral moieties in the side chains. The polymers were film‐formable, and in the films of polymers bearing the glycine‐ and alanine‐derived side chains, presence of hydrogen bonding was confirmed by IR analysis. Thermogravimetric analysis of the polymers revealed that the temperatures of 5% weight loss were higher than 300 °C. Differential scanning calorimetry clarified that the polymers were amorphous ones showing glass transition temperatures in a range of 48–80 °C. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3996–4002     

Photoaddition of maleic anhydride to unsaturated polymers in homogeneous solution,solid polymer–solution,and solid polymer–vapor systems

Photoreactions of maleic anhydride (MAH) with unsaturated olefinic polymers such as 1,2-polybutadiene, 1,4-polybutadiene, block copolymer of styrene and butadiene, polystyrene, poly(styrene-co-isoprene), and poly(styrene-alt-methyl methacrylate) were investigated in air. When the polymers have olefinic unsaturation, the addition of MAH to the polymers in homogeneous solutions proceeded efficiently by a chain mechanism, and the quantum yield of the photoaddition of MAH was greater than unity under irradiation at λ > 310 nm. From the effects of solvent and photosensitizer, a radical chain mechanism involving crosslinking of the polymers by MAH molecules was suggested. Together with the spectroscopic results, the reaction mechanism was discussed. The photoaddition reaction was then applied to the surface photomodification of polymer films. Photoreactions were conducted at the interphase between solid polymer and acetone solution of MAH and also at the interphase between solid polymer and gaseous MAH. Irradiation by a 300-W high-pressure mercury lamp could bring about considerable modification of the surface properties of the polymers, which then show improved wettability and dyeability. From the oxygen permeation experiments, the present interfacial phototreatment was shown to provide a double-layered polymer film in which one side of the film is polar and hydrophilic while the other side is nonpolar and hydrophobic.     

Choose sides: differential polymer adhesion

AFM-based single molecule desorption measurements were performed on surface end-grafted poly(acrylic acid) monolayers as a function of the pH of the aqueous buffer to study the adhesion properties of polymers that bridge two surfaces. These properties were found to depend on the adhesion forces of both surfaces in a differential manner, which is explained with a simple model in analogy to the Bell-Evans formalism used in dynamic force spectroscopy. The measured interaction forces between the poly(acrylic acid) chains and silicon nitride AFM tips depend on the grafting density of the polymer monolayers as well as on the contour length of the polymer chains. This study demonstrates that the stability of polymer bridges is determined by the adhesion strengths on both surfaces, which can be tuned by using pH-dependent polyelectrolyte monolayers.     

基于环糊精包结络合作用的大分子自组装

本文综述了基于环糊精包结络合作用的大分子自组装的研究进展,包括：（1) 线型、梳型、多臂星型或超支化聚合物与环糊精或其二聚体自组装形成多聚轮烷（分子项链）、多聚准轮烷、双多聚（准）轮烷、分子管、双分子管、超分子凝胶及其应用;（2）桥联环糊精与桥联客体分子自组装制备线型或超支化超分子聚合物;（3）温度、pH值、光及客体分子刺激响应智能体系; （4) 通过亲水性的环糊精线型均聚物与含金刚烷的疏水性聚合物之间的包结络合作用来制备高分子胶束及其空心球等。     

Synthesis of pH-responsive polysilane with polyelectrolyte side chains through γ-ray-induced graft polymerization

Polysilanes with polyelectrolyte side chains are synthesized by two methods utilizing γ-ray-induced grafting and the pH responsiveness for one of those polymers is revealed mainly by investigating interfacial behavior of its monolayer at the air/water interface. In the first synthetic method, poly(methyl acrylate) is grafted onto poly(methyl-n-propylsilane) (PMPrS) through γ-ray-induced grafting, and then the PMA chains are hydrolyzed to poly(acrylic acid) resulting in the yield of ca. 97%. Thus PMPrS with polyelectrolyte side chains is successfully synthesized by the graft chain hydrolysis. The other method is the direct grafting of electrolyte monomers. Poly(methacrylic acid)-grafted PMPrS (PMPrS-g-PMAA) can be obtained through γ-ray-induced grafting of methacrylic acid monomers onto PMPrS chains, which shows the effectiveness of radiation grafting for the synthesis of polyelectrolyte graft copolymers. PMPrS-g-PMAA exhibits pH responsive behavior. In addition to the pH-dependence of water solubility, interfacial behavior also depends on the pH. Langmuir monolayers of PMPrS-g-PMAA exhibit different surface pressure-area isotherms according to the grafting yield and the pH of the subphase water. This result suggests that radiation modification is useful for fabricating polysilane-based ordered materials responsive to outer stimuli.     

Amphiphilic Heterografted Molecular Bottlebrushes with Tertiary Amine-Containing Side Chains as Efficient and Robust pH-Responsive Emulsifiers

By combining the unique characteristics of molecular bottlebrushes (MBBs) and the properties of stimuli-responsive polymers, we show that MBBs with randomly grafted poly(n-butyl acrylate) and pH-responsive poly(2-(N,N-diethylamino)ethyl methacrylate) (PDEAEMA) side chains are efficient and robust pH-responsive emulsifiers. Water-in-toluene emulsions were formed at pH 4.0 and disrupted by increasing the pH to 10.0. The emulsion generation and disruption was reversible over the ten cycles investigated, and the bottlebrushes remained intact. The exceptional emulsion stability stemmed from the high interfacial binding energy of MBBs, imparted by their large molecular size and Janus architecture at the interface, as evidenced by the interfacial jamming and wrinkling of the assemblies upon reducing the interfacial area. At pH 10.0, PDEAEMA became water-insoluble, and the MBBs desorbed from the interface, causing de-emulsification. Consequently, we have shown that the judicious design of MBBs can generate properties of particle emulsifiers from their large size, while the responsiveness of the MBBs enables more potential applications.