Solvothermal synthesis of WO3/TiO2/carbon fiber composite photocatalysts for enhanced performance under sunlight illumination

Carbon fiber (CF)‐based WO₃/TiO₂ composite catalysts (WO₃/TiO₂/CF) were successfully synthesized by solvothermal method. The catalysts were characterized by XPS, SEM, BET, XRD, FTIR, Raman and UV–Vis. The analyses confirmed the WO₃/TiO₂ nanoparticles with high crystallinity deposited on the carbon structure. The photocatalytic degradation of Orange II azo dye under UV and sunlight illumination with the synthesized catalyst was explored. The composite catalyst displayed high performance (85%) for Orange II degradation while that of for WO₃/TiO₂ was found as 76%. The effects of CF amount, solution pH, initial dye concentration and catalyst dose on photocatalytic performance were studied. It was found that the degradation efficiency increased from 68% to 90% with the increasing CF amount from 3 wt% to 5 wt%, while the further increase in CF amount (7–10 wt%) decreased the photodegradation due to the blocking the active sites of WO₃/TiO₂. The enhanced photocatalytic efficiency was mainly attributed to the electrical properties of the CF and reduced bandgap.     

Low-Temperature Oxidation of Carbon Monoxide: The Synthesis and Properties of a Catalyst Based on Titanium Dioxide,Nanodiamond, and Palladium for CO Oxidation

A catalyst based on TiO₂ and nanodiamond with a 10 wt % palladium content of the catalyst was synthesized. The effect of the nanodiamond content on the catalytic properties in a reaction of CO oxidation at room temperature and low concentrations of CO (<100 mg/m³) was studied. It was established that, at a nanodiamond content of the catalyst from 7 to 9 wt % and a palladium content of 10 wt %, the rate of CO oxidation reached a maximum, and it was higher by a factor of 2.5 than the rate of CO oxidation on a catalyst based on pure TiO₂, which included palladium clusters. With the use of transmission electron microscopy, XRD X-ray diffractometry, and X-ray photoelectron spectroscopy, it was found that the clusters of palladium covered with palladium oxide with an average cluster size of 4 nm were formed on the surface of the TiO₂ carrier. It was assumed that the catalyst synthesized is promising for applications in catalytic and photocatalytic air-cleaning systems.     

Alcohol‐Selective Oxidation in Water under Mild Conditions via a Novel Approach to Hybrid Composite Photocatalysts

The oxidation of alcohols to carbonyl compounds in a clean fashion (i.e., with water as a solvent or under solvent‐free conditions, and using O₂ or H₂O₂ as the primary oxidant) is the subject of considerable research efforts. A new approach for the selective oxidation of soluble aromatic alcohols in water under mild conditions via a novel composite photocatalyst has been developed. The catalyst is synthesized by grafting 4‐(4‐(4‐hydroxyphenylimino)cyclohexa‐2,5dienylideneamino)phenol and silver nanoparticles onto the surface of moderately crystalline titanium dioxide. The titanium dioxide‐based composite was first extensively characterized and then employed in the catalytic oxidation of 4‐methoxybenzyl alcohol to 4‐methoxybenzaldehyde under UV irradiation in water at room temperature. The corresponding aldehyde was obtained with unprecedented high selectivity (up to 86 %). The method is general and opens the route to fabrication of photocatalytic composites based on titanium dioxide functionalized with shuttle organic molecules and metal nanoparticles for a variety of oxidative conversions.     

Selectivity in the Ligand Functionalization of Photocatalytic Metal Oxide Nanoparticles for Phase Transfer and Self-Assembly Applications

The functionalization of photocatalytic metal oxide nanoparticles of TiO₂, ZnO, WO₃ and CuO with amine-terminated (oleylamine) and thiol-terminated (dodecane-1-thiol) alkyl-chain ligands was studied under ambient conditions. A high selectivity was observed in the binding specificity of a ligand towards nanoparticles of these different oxides. It was observed that oleylamine binds stably to only TiO₂ and WO₃, whereas dodecane-1-thiol binds stably only to ZnO and CuO. Similarly, polar-to-nonpolar solvent phase transfer of TiO₂ and WO₃ nanoparticles could be achieved by using oleylamine, but not dodecane-1-thiol, whereas the opposite holds for ZnO and CuO. The surface chemistry of ligand-functionalized nanoparticles was probed by attenuated total reflectance (ATR)-FTIR spectroscopy, which enabled the occupation of the ligands at the active sites to be elucidated. The photostability of the ligands on the nanoparticle surface was determined by the photocatalytic self-cleaning properties of the material. Although TiO₂ and WO₃ degrade the ligands within 24 h under both UV and visible light, ligands on ZnO and CuO remain unaffected. The gathered insights are also highly relevant from an application point of view. As an example, because the ligand-functionalized nanoparticles are hydrophobic in nature, they can be self-assembled at the air-water interface to give nanoparticle films with demonstrated photocatalytic as well as anti-fogging properties.     

TiO<Subscript>2</Subscript>/WO<Subscript>3</Subscript> photoanodes with enhanced photocatalytic activity for air treatment in a polymer electrolyte cell

The application of electrochemically enhanced photocatalysis in air treatment using a Nafion-based photoelectrochemical cell and TiO₂/WO₃ photoanodes for organic vapor photooxidation under both UV and visible light irradiation is briefly presented. In that direction, the obtained results regarding the preparation and characterization of the TiO₂/WO₃ photoanodes with enhanced photocatalytic activity are reviewed. Particular emphasis is given in the comparison of the photocatalytic behavior of bilayer TiO₂/WO₃ coatings, electrosynthesized on stainless steel mesh and powder C + mixed (WO₃ + TiO₂) photoanodes. The advantages of using a high surface area C + mixed (WO₃ + TiO₂) powder catalysts as photoanodes against their plain TiO₂ + C and WO₃ + C analogues are discussed.     

Correlation of the Catalytic Activity for Oxidation Taking Place on Various TiO2 Surfaces with Surface OH Groups and Surface Oxygen Vacancies

Three catalytic oxidation reactions have been studied: The ultraviolet (UV) light induced photocatalytic decomposition of the synthetic dye sulforhodamine B (SRB) in the presence of TiO₂ nanostructures in water, together with two reactions employing Au/TiO₂ nanostructure catalysts, namely, CO oxidation in air and the decomposition of formaldehyde under visible light irradiation. Four kinds of TiO₂ nanotubes and nanorods with different phases and compositions were prepared for this study, and gold nanoparticle (Au‐NP) catalysts were supported on some of these TiO₂ nanostructures (to form Au/TiO₂ catalysts). FTIR emission spectroscopy (IES) measurements provided evidence that the order of the surface OH regeneration ability of the four types of TiO₂ nanostructures studied gave the same trend as the catalytic activities of the TiO₂ nanostructures or their respective Au/TiO₂ catalysts for the three oxidation reactions. Both IES and X‐ray photoelectron spectroscopy (XPS) proved that anatase TiO₂ had the strongest OH regeneration ability among the four types of TiO₂ phases or compositions. Based on these results, a model for the surface OH group generation, absorption, and activation of molecular oxygen has been proposed: The oxygen vacancies at the bridging O^2? sites on TiO₂ surfaces dissociatively absorb water molecules to form OH groups that facilitate adsorption and activation of O₂ molecules in nearby oxygen vacancies by lowering the absorption energy of molecular O₂. A new mechanism for the photocatalytic formaldehyde decomposition with the Au/TiO₂ catalysts is also proposed, based on the photocatalytic activity of the Au‐NPs under visible light. The Au‐NPs absorb the light owing to the surface plasmon resonance effect and mediate the electron transfers that the reaction needs.     

Deposition of SnO2 on the Anatase TiO2 {105} Facets with High Photocatalytic Performance

Anatase TiO2 as a promising photocatalyst has been widely employed in the decontamination treatment of polluted water, air purification and water splitting. Coupling TiO2 with other semiconductor materials could further enhance the photocatalytic activity. Here, we successfully synthesized the SnOz/TiO2 catalyst by depositing SnO2 particles on the anatase TiO2 {105} facets through a gas phase oxidation process. The SnOz/TiO2 catalyst shows higher photocatalytic activity for decomposition of MB than that of the pure YiO2 catalyst. The enhanced photo- catalytic activity can be attributed to the efficient charge separation since TiO2 and SnO2 catalyst have staggered energy level.     

Photocatalytic Oxidation of Aniline in the Gas Phase Using Porous TiO2 Thin Films

The gas-phase photocatalytic oxidation of aniline on a new kind of porous nano-TiO₂ composite films is investigated. The composite film was prepared on glass fiber with the water glass as binders and dilute H₂SO₄ solution as solidifying reagent. The surface characters were observed by scanning electron microscope. The photocatalytic degradation of aniline on the composite films was carried out in a TiO₂/UV system. Some important factors affecting the photodegradation, such as the concentration of TiO₂, the initial concentration of aniline, and the existing water vapor, are also studied. The product of photocatalytic oxidation was detected by Fourier transform-Infrared. The partial intermediate products were absorbed on TiO₂ surface, which resulted in catalyst deactivation. But when it was irradiated under UV illumination or solar irradiation for some time, the catalyst could be reused without loss of catalytic activity. Translated from the Journal of Wuhan University (Natural Science Edition), 2005, 51(2) (in Chinese)     

Photocatalytic Oxidation Based on Modified Titanium Dioxide with Reduced Graphene Oxide and CdSe/CdS as Nanohybrid Materials

Photocatalytic activity of TiO₂ nanoparticles in the visible light region was enhanced. TiO₂–CdSe and TiO₂–CdSe/CdS nanohybrids were supported on the reduced graphene oxide. These nanohybrid materials were applied as photocatalyst toward oxidation of aromatic alcohols under a mild condition and the molecular oxygen as oxidant. A plausible mechanism for the photocatalytic oxidation was also proposed. Desired nanohybrids were obtained via in situ fixation of CdSe/CdS on the surface of nanosheets of reduced graphene oxide (rGO). Finally, it was modified by TiO₂ sol nanoparticles through a hydrothermal method. The obtained nanomaterials, were characterized by SEM, TEM imaging, XRD, EDAX, DRS and XPS analyses. The size of nanohybrids materials were distributed mostly in a narrow range of 50–65 and 60–75 nm for TiO₂–rGO–CdSe and TiO₂–rGO–CdSe/CdS, respectively. These photocatalysts showed high catalytic activity under visible light irradiation in a short reaction time and even higher selectivity rather than UV irradiation. The yield of catalytic oxidation increased at least 25–30% for TiO₂–CdSe/CdS on rGO, which could be related to its higher light sensitivity and lower energy band gap. The photocatalysts were recycled and reused 8 times without significant loss of their activities due to their stability under visible light.     

Synthesis of Three‐dimensionally Ordered Macroporous TiO2 and TiO2/WO3 Composites and Their Photocatalytic Performance

This work presents the characterization and preparation of three‐dimensionally ordered macroporous TiO₂ and TiO₂/WO₃ composite nanoparticles with enhanced visible‐light‐responsive properties for rhodamine B (Rh B) photodegradation. The 3DOM TiO₂ and TiO₂/WO₃ composites were prepared through a dip‐infiltrating sol‐gel process using a polystyrene (PS) colloidal crystal template. The materials were characterized by SEM, TEM, XRD, BET, XPS and UV/Vis. The 3DOM TiO₂/WO₃ composite structures ranged from well‐defined 3DOM structures, which are highly ordered and interconnected via small pore windows, to collapsed three‐dimensional structures as the WO₃ content increased. The photoresponse range and specific surface area of the composite increased with less than 0.025 g of WCl₆. The 3DOM TiO₂/WO₃ composite with less than 0.025 g of WCl₆ exhibited a higher catalytic activity than 3DOM TiO₂ for the photocatalytic degradation of Rh B under simulated sunlight illumination.     

An easy one-step photocatalytic synthesis of 1-aryl-2-alkylbenzimidazoles by platinum loaded TiO2 nanoparticles under UV and solar light

One-pot synthesis of disubstituted benzimidazoles from N-substituted 2-nitroanilines or 1,2-diamines with 3-12 nm-sized platinum particles loaded on the TiO₂ using solar and UV-A light is described. 1-Aryl-2-alkylbenzimidazoles from 2-nitrodiphenylamines are formed by combined redox photocatalytic reaction, condensation and catalytic dehydrogenation on Pt-TiO₂. In case of diamines, this reaction is proceeded by Pt-TiO₂ assisted photocatalytic oxidation of an alcohol and a catalytic dehydrogenation of the intermediate on the surface of platinum nanoparticles. In both cases product formation was achieved by tandem photocatalytic and catalytic reactions on Pt-TiO₂.     

Visible‐Light‐Induced Efficient Selective Oxidation of Nonactivated Alcohols over {001}‐Faceted TiO2 with Molecular Oxygen

In the presence of molecular oxygen, a {001}‐faceted nanocrystalline anatase TiO₂ catalyst enabled the selective oxidation of nonactivated aliphatic alcohols to the corresponding aldehydes or ketones under visible light. The reaction shows excellent conversion and selectivity towards the formation of the carbonyl products without over‐oxidation to the corresponding carboxylic acids. The exceptional reactivity of the catalyst is possibly due to the absorption of visible light originating from a stronger interaction of alcohol with the {001} facet, which facilitates the modification of the band structure of TiO₂, thus facilitating the photogenerated hole transfer and subsequent oxidation processes. The experimental results have also been corroborated by first‐principles quantum chemical DFT calculations.     

In situ FT-IR studies of NO decomposition on Pt/TiO2 catalyst under UV irradiation

Photodecomposition of NO on the well-dispersed Pt/TiO₂ catalyst under UV irradiation was studied by in situ DRIFT (Diffuse-Reflectance Infrared Fourier-Transform) spectroscopy. 2 wt% Pt/TiO₂ catalyst was prepared by photochemical deposition method. The photocatalytic activity of Pt/TiO₂ is highly dependent on its pretreatment. Although the catalyst exhibited a highly adsorption capability to NO after hydrogen reduction or thermal evacuation at 500°C, no evidence upon NO decomposition was observed under UV irradiation. While reducing the catalyst at 300°C in the hydrogen flow, it not only exhibited an intense NO adsorption but also conducted a direct decomposition of NO to N₂ and O₂ under UV irradiation. The hydrogen reduction at 200°C led to a weaker NO adsorption. During UV irradiation, the IR peaks of NO fully disappeared and N₂O was formed. It is concluded that the photochemical prepared Pt/TiO₂ catalyst after activating at mild reduction conditions is highly active for NO photodecomposition. The effective oxidation states of the active components, the surface structure and the reaction mechanisms will be discussed.     

Highly selective oxidation of alcohols using MnO2/TiO2-ZrO2 as a novel heterogeneous catalyst

MnO₂/TiO₂-ZrO₂, which was synthesized by the adsorption method, demonstrated very high catalytic activity in the selective oxidation of benzyl alcohols to benzaldehydes with excellent yields and selectivity in short reaction times. The physical and chemical properties of MnO₂/TiO₂-ZrO₂ were investigated by XRD, XRF, BET, FT-IR and SEM techniques. The influence of the catalyst support (SBA-15, ZSM-5, TiO₂-ZrO₂ and Y), type of metal oxide supported, method of loading and amount of manganese nitrate loading have been thoroughly investigated. Moreover, the catalyst has shown excellent reusability in the process.     

High catalytic performance of the first electrospun nano-biohybrid,Mn3O4/copper complex/polyvinyl alcohol,from Amaranthus spinosus plant for biomimetic oxidation reactions

In this study, a novel nano-biocomposite, polyvinylalcohol/Mn₃O₄/water-soluble copper complex (PVA/Mn₃O₄/CuWSC), was produced from Amaranthus spinosus. By combining water-soluble copper nanocomplex and Mn₃O₄ nanoparticles along with polyvinyl alcohols and extracts of this plant, this bio nanomaterial was prepared via electrospinning process. This nanohybrid was characterized using transmission electron microscopy, scanning electron microscopy, atomic force microscopy, Fourier-transform infrared spectroscopy, X-ray diffraction, energy-dispersive X-ray spectroscopy, and elemental analysis. Based on its catalytic activities, it is considered a heterogeneous catalyst and is used for the oxidation of alcohols in industrial reactions. It can oxidize the primary and secondary alcohols to corresponding aldehyde and ketone products with high yield and excellent selectivity using H₂O₂ under solvent-free conditions. The recyclability and reusability of PVA/Mn₃O₄/CuWSC show that it can be a promising catalyst for clean industrial catalytic applications.     

Selective oxidation of alcohols with hydrogen peroxide catalyzed by tungstate ions (WO4) supported on periodic mesoporous organosilica with imidazolium frameworks (PMO-IL)

Tungstate ions supported on the periodic mesoporous organosilica with ionic liquid frameworks (WO₄⁼@PMO-IL) were found to be a recoverable catalyst system for the highly selective oxidation of various primary or secondary alcohols to the corresponding aldehydes or ketones by 30% H₂O₂ as green oxidant under neutral aqueous reaction conditions. The catalyst can be also recovered and efficiently reused in seven subsequent reaction cycles without any remarkable decreasing in the catalyst activity and selectivity. Moreover, N₂ sorption analysis, transmission electron microscopy (TEM) images, and thermal gravimetric analysis (TGA) showed that the structure regularity and functional groups loaded of the catalyst were not affected during the reaction process.     

Nano‐WO3‐SO3H as a New Photocatalyst Insight Through Covalently Grafted Brønsted Acid: Highly Efficient Selective Oxidation of Benzyl Alcohols to Aldehydes

Modification of nano‐WO₃ with ?SO₃H groups as a covalently grafted solid acid reduced its band‐gap energy from 2.8 to 2.4 eV and made it an ideal nominee for photocatalytic reaction under visible light irradiation. This nano‐photocatalyst has been successfully used for the selective oxidation of different benzyl alcohols to corresponding aldehydes under blue LED irradiation. The reaction became approximately two times faster with excellent yields. It has shown that the nitrobenzene as an available industrial oxidant is applicable for photocatalytic oxidation of benzyl alcohol; remarkably high yield and selectivity have been observed.     

The Hazardous Origin of Photocatalytic Activity of ZnCr2O4

The ZnCr₂O₄ catalysts are synthesized by thermal decomposition of (NH₄)₂[Zn(NH₃)₂(CrO₄)₂] and materials with high surface areas and particle sizes in the nano regime are obtained. A special structural feature of the materials are stacking faults with densities strongly depending on the synthesis temperature, i.e. the lower the temperature the larger the number of stacking faults. The catalyst prepared at the lowest decomposition temperature exhibiting the smallest particle size shows the highest catalytic activity in the photocatalytic degradation of y‐Eosin in a photo‐Fenton process. The results of different analytic methods demonstrate that the high catalytic activity is directly correlated with CrO₄^2– anions generated via photo‐oxidation of the catalyst. Therefore, ZnCr₂O₄ cannot be regarded as an environmental friendly catalyst for advanced photocatalytic oxidation processes.     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附-脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Controlling the Selectivity of the Surface Plasmon Resonance Mediated Oxidation of p‐Aminothiophenol on Au Nanoparticles by Charge Transfer from UV‐excited TiO2

Although catalytic processes mediated by surface plasmon resonance (SPR) excitation have emerged as a new frontier in catalysis, the selectivity of these processes remains poorly understood. Here, the selectivity of the SPR‐mediated oxidation of p‐aminothiophenol (PATP) employing Au NPs as catalysts was controlled by the choice of catalysts (Au or TiO₂‐Au NPs) and by the modulation of the charge transfer from UV‐excited TiO₂ to Au. When Au NPs were employed as catalyst, the SPR‐mediated oxidation of PATP yielded p,p‐dimercaptobenzene (DMAB). When TiO₂‐Au NPs were employed as catalysts under both UV illumination and SPR excitation, p‐nitrophenol (PNTP) was formed from PATP in a single step. Interestingly, PNTP molecules were further reduced to DMAB after the UV illumination was removed. Our data show that control over charge‐transfer processes may play an important role to tune activity, product formation, and selectivity in SPR‐mediated catalytic processes.