Photo-cross-linkable polyelectrolyte multilayers for 2-D and 3-D patterning

We report the synthesis of poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linkable weak polyelectrolyte, and its incorporation into polyelectrolyte multilayer (PEM) films. PEM films assembled from PAArVBA and poly(allylamine hydrochloride) (PAH) are found to exhibit similar thickness trends with assembly pH as those previously reported for poly(acrylic acid) (PAA)/PAH multilayers. Swelling properties of the as-built and photo-cross-linked films are studied by in situ ellipsometry. Two-dimensional masking techniques are used to pattern regions of high and low swelling, as confirmed by atomic force microscopy (AFM), and to provide spatial control over the low-pH-induced microporosity transition exhibited by PAH/PAA PEMs. Films containing alternating blocks of PAH/PAArVBA bilayers and PAH/PAA bilayers were assembled, laterally photopatterned, and exposed to low-pH solution to generate nanoporosity leading to patterned Bragg reflectors, thereby demonstrating three-dimensional control over film structure in these weak PEM assemblies.     

Synthesis, multilayer film assembly, and capsule formation of macromolecularly engineered acrylic acid and styrene sulfonate block copolymers

We report the use of copolymers synthesized with specific block ratios of weakly and strongly charged groups for the preparation of stable, pH-responsive multilayers. In this study, we utilized reversible addition-fragmentation chain transfer (RAFT) polymerization in the synthesis of novel pH-sensitive copolymers comprising block domains of acrylic acid (AA) and styrene sulfonate (SS) groups. The PAA x- b-SS y copolymers, containing 37%, 55%, and 73% of AA groups by mass (denoted as PAA 37- b-SS 63, PAA 55- b-SS 45, and PAA 73- b-SS 27, respectively), were utilized to perform stepwise multilayer assembly in alternation with poly(allylamine hydrochloride), PAH. The ratio of AA to SS groups, and the effect of the pH of both anionic and cationic adsorption solutions, on multilayer properties, were investigated using ellipsometry and atomic force microscopy. The presence of SS moieties in the PAA x- b-SS y copolymers, regardless of the precise composition, lead to films with a relatively consistent thickness. Exposure of these multilayers to acidic conditions postassembly revealed that these multilayers do not exhibit the characteristic large swelling that occurs with PAA/PAH films. The film stability was attributed to the presence of strongly charged SS groups. PAA x- b-SS y/PAH films were also formed on particle substrates under various adsorption conditions. Microelectrophoresis measurements revealed that the surface charge and isoelectric point of these core-shell particles are dependent on assembly pH and the proportion of AA groups in PAA x- b-SS y. These core-shell particles can be used as precursors to hollow capsules that incorporate weak polyelectrolyte functionality. The role of AA groups in determining the growth profile of these capsules was also examined. The multilayer films prepared may find applications in areas where pH-responsive films are required but large film swelling is unfavorable.     

Directed Self-assembly of Vertical PS-b-PMMA Nanodomains Grown on Multilayered Polyelectrolyte Films

Layer-by-layer polyelectrolyte self-assembly, a common method for preparing high-quality ultra-thin films, was employed to direct the self-assembly behavior of polystyrene-block-poly(methyl methacrylate)(PS-b-PMMA) block copolymer for the first time. Differing from the previous neutral polymer brushes anchored to silicon substrates via chemical modification, polyelectrolyte multilayers(PEMs) were anchored by electrostatic interaction and provided a stable, smooth, and neutral interface. In the present study, PS-b-PMMA was deposited on poly(acrylamide hydrochloride)/poly(acrylic acid)(PAH/PAA) PEMs prepared by layer-by-layer self-assembly to successfully yield vertical nanodomains after thermal annealing. Seven layered PEMs revealed an excellent, smooth surface, with a low roughness of 0.6 nm. The periodic structure with interlamellar spacing of 47 nm was determined by grazing-incidence small-angle X-ray scattering(GISAXS). The morphology of the PS-b-PMMA nanodomains depended on the polyanion-to-polycation concentration ratio, which is related to the interaction between the block copolymer and the substrate. Our results demonstrate that layer-by-layer self-assembly is a helpful method for the phase separation of block polymers and the fabrication of vertical, ordered nanodomains.     

Correlating the compliance and permeability of photo-cross-linked polyelectrolyte multilayers

Photo-cross-linkable polyelectrolyte multilayers were made from poly(allylamine) (PAH) and poly(acrylic acid) (PAA) modified with a photosensitive benzophenone. Nanoindentation, using atomic force microscopy (AFM) of these and unmodified PAH/PAA multilayers, was used to assess their mechanical properties in situ under an aqueous buffer. Under the conditions employed (and a 20 nm radius AFM tip), reliable nanoindentations that appeared to be decoupled from the properties of the silicon substrate were obtained for films greater than 150 nm in thickness. A strong difference in the apparent modulus was observed for films terminated with positive as compared to negative polyelectrolytes. Films terminated with PAA were more glassy, suggesting better charge matching of polyelectrolytes. Multilayers irradiated for up to 100 min showed a smooth, controlled increase in the modulus with little change in the water contact angle. The permeability to iodide ion, measured electrochemically, also decreased in a controlled fashion.     

Characterization of pH-induced changes in the morphology of polyelectrolyte multilayers assembled from poly(allylamine) and low molecular weight poly(acrylic acid)

We report characterization of pH-dependent behavior in polyelectrolyte multilayers (PEMs) fabricated from poly(allylamine) (PAH) and low molecular weight poly(acrylic acid) (PAA) synthesized by living/controlled polymerization. Exposure of these films to solutions of low pH (e.g. pH 2.0-3.2) resulted in transformations from films that were smooth and uniform to films with porous morphologies, as characterized by scanning electron microscopy (SEM). We observed large differences in both the extent of this transformation and the sizes of the pores that resulted compared to films fabricated using higher molecular weight PAA used in past studies. Whereas transformations reported in past studies generally lead to pores with sizes in the range of 0.3-2 μm, we observed larger-scale transformations and films with cell-like internal structures comprised of networks of closed pores, interconnected pores, and through-pores with sizes as large as 10-15 μm depending on pH and the manner in which the films were incubated. Films fabricated using fluorescently end-labeled samples of PAA permitted real-time imaging of changes in internal structure using confocal microscopy (LSCM). The results of these studies also revealed large differences in the nature of these transformations when films were placed in contact with surfaces as opposed to when dipped into aqueous solutions. Our results reveal approaches that can be used to fabricate films with large pores (e.g., pores with sizes on the order of 10-15 μm) and suggest methods that could potentially be used to generate PEMs having controlled gradients in pore size.     

Separation of aminophenol isomers in polyelectrolyte multilayers modified PDMS microchip

The separation of three kinds of aminophenol isomers were achieved within 1 min in polyelectrolytes multilayers modified PDMS microchips by layer-by-layer assembly with electrochemical detection (EC). Two polyelectrolytes, poly(dially dimethyl ammonium chloride) (PDDA) and poly(sodium-4-styrene-sulfonate) (PSS) were used to form polyelectrolyte multilayers (PEMs). The surface characteristic of the modified microchip was studied by XPS. The electroosmotic flow (EOF) on PEMs modified PDMS microchips was more stable than that of the native PDMS microchips and the adsorption of samples was greatly reduced on PEMs modified PDMS microchips during the electrophoretic process. The column efficiencies on PEMs modified microchip were increased by 100 times and the signals enhanced by 2 times compared with those of native microchips. The separation conditions such as running buffer pH, running buffer concentration and separation voltage were also optimized.     

Assessment of polyelectrolyte coating stability under dynamic buffer conditions in CE

Dynamic buffer conditions are present in many electrophoretically driven separations. Polyelectrolyte multilayer coatings have been employed in CE because of their chemical and physical stability as well as their ease of application. The goal of this study is to measure the effect of dynamic changes in buffer pH on flow using a real-time method for measuring EOF. Polyelectrolyte multilayers (PEMs) were composed of pairs of strong or completely ionized polyelectrolytes including poly(diallyldimethylammonium) chloride and poly(styrene sulfonate) and weak or ionizable polyelectrolytes including poly(allylamine) and poly(methacrylic acid). Polyelectrolyte multilayers of varying thicknesses (3, 4, 7, 8, 15, or 16 layers) were also studied. While the magnitude of the EOF was monitored every 2 s, the buffer pH was exchanged from a relatively basic pH (7.1) to increasingly acidic pHs (6.6, 6.1, 5.5, and 5.1). Strong polyelectrolytes responded minimally to changes in buffer pH (<1%), whereas substantial (>10%) and sometimes irreversible changes were measured with weak polyelectrolytes. Thicker coatings resulted in a similar magnitude of response but were more likely to degrade in response to buffer pH changes. The most stable coatings were formed from thinner layers of strong polyelectrolytes.     

Modulation of hemocompatibility of polysulfone by polyelectrolyte multilayer films

Polyelectrolyte multilayer (PEM) films have been recently applied to surface modification of biomaterials. Cellular interactions with PEM films consisted of weak polyelectrolytes are greatly affected by the conditions of polyelectrolyte deposition, such as pH of polyelectrolyte solution. Previous studies indicated that the adhesion of several types of mammalian cells to PAH/PAA multilayer films was hindered by low pH and high layer numbers. The objective of this study is to evaluate whether the hemocompatibility of polysulfone can be modulated by deposition of poly(allylamine hydrochloride) (PAH)/poly(acrylic acid) (PAA) multilayer films. PAH/PAA multilayer films with different layer numbers were assembled onto polysulfone at either pH 2.0 or pH 6.5. The number of platelet adhesion and the morphology of adherent platelets were determined to evaluate hemocompatibility of modified substrates. Compared to non-treat polysulfone, the PEM films developed at pH 2.0 decreased platelet adhesion, while those built at pH 6.5 enhanced platelet deposition. Platelet adhesion was found positively correlated to polyclonal antibodies binding to surface-bound fibrinogen. The extent of platelet spreading was increased with layer numbers of PEM films, suggesting that the adherent platelets on thick PEM films were prone to activation. In conclusion, PAH/PAA films with few layers developed at pH 2.0 possessed better hemocompatibility compared to other substrates.     

Unusual collapse of highly hydrated polyelectrolyte multilayers with the ionic strength

Highly hydrated polyelectrolyte multilayers (PEMs) were fabricated by “layer by layer” (LBL) assembly of poly (diallyl dimethyl ammonium chloride) (PDADMAC) and poly (sodium 4‐styrene sulfonate) (PSS) in 0.5 M NaCl. Both thickness and hydration of the film were determined in situ as the multilayer was assembled by means of the quartz crystal microbalance with dissipation (QCM‐D) and the Spectroscopic Ellipsometry techniques combined in a single device. For PEMs of 17 total layers in water, a final thickness of up to 300 nm and a hydration of 69% were measured. The response towards the ionic strength was then studied by means of QCM‐D. PEMs of 17 layers, with PDADMAC as last layer, shrunk dramatically and lost water when exposed to aqueous NaCl solutions of increasing concentration. Indeed, a thickness variation up to 100 nm and reduction in the 50% of the water content were observed when the PEM was exposed to 1 M NaCl. On the contrary, PEMs where PSS appears on top showed no measurable change upon the variation in the ionic strength. This brings the possibility to control the responsive character of the PEMs simply by selecting the last polyelectrolyte layer (PDADMAC or PSS) deposited. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Responsive Polyelectrolyte Multilayers Assembled at High Ionic Strength with an Unusual Collapse at Low Ionic Strength

Responsive polyelectrolyte multilayers (PEMs) of poly(diallyl dimethyl ammonium chloride) (PDADMAC) and poly(styrene sodium sulfonate) (PSS) with thicknesses between 350 and 400 nm for 11 deposited polyelectrolyte layers were fabricated assembling the polyelectrolytes at 3 M NaCl. When the 3 M NaCl bulk solution is replaced by water, the PEMs release water, approximately a 46% of the total mass, and experience a thickness reduction of more than 200 nm. Changes in thickness and water content are fully reversible. The film recovers its original thickness and water content when it is exposed again to a 3 M NaCl solution. A responsive polymer film is achieved with the capability of swelling at high ionic strength and collapsing in water with variations in thickness of hundred of nanometers.     

Characterization of the growth of polyelectrolyte multilayers formed at interfaces between aqueous phases and thermotropic liquid crystals

Polyelectrolyte multilayers (PEMs) formed at interfaces between aqueous solutions and thermotropic (water-immiscible) liquid crystals (LCs) offer the basis of a new method to tailor the nanometer-scale structure and chemical functionality of these interfaces. Toward this end, we report a study that compares the growth of PEMs formed at mobile and deformable interfaces defined by LCs relative to growth observed at model (rigid) solid surfaces. Experiments aimed at determining if polyelectrolytes such as poly(sodium-4-styrenesulfonate) (PSS) can partition from the aqueous phase into the bulk of the LC yielded no evidence of such partitioning. Whereas measurements of the growth of PEMs formed from poly(allylamine hydrochloride) (PAH) and PSS at the aqueous-LC interface revealed growth characteristics similar to those measured at both hydrophobic and hydrophilic interfaces of solids, the growth of PEMs from PAH and poly(acrylic acid) (PAA) at the aqueous-LC interface was found to differ substantially from the solids investigated: (i) the linear growth of PEMs of PAH/PAA that was measured at the aqueous-LC interface under conditions that did not lead to the growth of PEMs at the interface of octadecyltrichlorosilane (OTS)-treated glass (a hydrophobic solid surface), and (ii) in comparison to the growth of PEMs of PAH/PAA at the surface of glass (a hydrophilic charged surface), a higher rate of growth was observed at the aqueous-LC interface. The finding that the growth rate of PEMs of PAH/PAA at aqueous-LC interfaces is greater than on solid surfaces is supported by additional measurements of growth as a function of pH. Finally, the pH-triggered reorganization of PAH/PAA PEMs supported at the aqueous-LC interface led to changes in the order and optical properties of the LC. These data are discussed in light of the nature of aqueous-LC interfaces, including the mobility and deformability of the interface and recent measurements of the zeta-potentials of aqueous-LC interfaces.     

Selective depositions on polyelectrolyte multilayers: self-assembled monolayers of m-dPEG acid as molecular template

This paper describes the fabrication of self-assembled monolayer (SAM) patterns of m-d-poly(ethylene glycol) (m-dPEG) acid molecules onto polyelectrolyte multilayers (PEMs). The patterned SAMs on PEMs were created by ionic interactions using microcontact printing (microCP) technique. The created m-dPEG acid monolayer patterns on PEMs act as resistive templates, and thus further depositions of consecutive poly(anion)/poly(cation) pairs of charged particles result in the formation of three-dimensional (3-D) patterned PEM films or selective particle depositions atop the original multilayer thin films. In this study, we illustrate nonlithographic methods of patterning and controlling 3-D PEM architectures and selective particle depositions. We investigated the effect of variables--the choice of solvent, concentration, pH, substrate pretreatment, and stamp contact times--on microcontact printing of m-dPEG acid molecules onto PEM films to determine the optimal conditions for these parameters to achieve efficient transfer of m-dPEG acid patterns onto PEMs. Among the variables, the pH of the m-dPEG acid ink solution played the most important role in the transfer efficiency of the patterns onto the multilayer films. The patterned films were characterized by optical microscopy and atomic force microscopy (AFM).     

Granular structure of self-assembled PAA/PAH and PSS/PAH nascent films imaged in situ by LC-AFM

Liquid cell atomic force microscopy (LC-AFM) is used to image self-assembled polyelectrolyte films eliminating any drying effects on the film structure. Weak/weak and strong/weak polyelectrolyte films are formed by the alternated deposition of poly(acrylic acid) [PAA]/poly(allylamine hydrochloride) [PAH], and poly(sodium 4-styrene sulfonate) [PSS]/PAH, respectively, forming a granular surface structure. Number and area of grains (GN, GA) are used to characterize the surface of these films during their build up process. We show that hydrophilic PAA increases GA and decreases GN, while these parameters follow an opposite behavior with PSS. In both cases, GA and GN always have a simple inverse relationship, and then grain surface coverage (GS=GNGA) is nearly constant and independent of polyelectrolyte nature and the substrates used here, but also in the published data as well. The drying of the weak/weak film was also imaged after natural and forced solvent evaporation, and the surface structure is strongly affected, although the GS values keep roughly the same value found for wet films. The set of these results indicates that GS may be considered as a constant parameter during the build-up for the self-nascent assembled polyelectrolytes. The granular structure is still maintained after glucose oxidase adsorption on these films with comparable GS values.     

Polymer-metal complexes in polyelectrolyte multilayer films as catalysts for oxidation of toluene

We report on the binding of metal ions (Me(2+); Co(2+) and Cu(2+)) with weak polyelectrolyte multilayers (PEMs), as well as on catalytic activity of PEM-Me(2+) films for oxidation of toluene. Using several types of PEM films constructed using branched polyethyleneimine (BPEI) or quaterinized poly-4-vinylpyridines (QPVPs) as polycations and poly(acrylic acid) (PAA) or poly(styrene sulfonate) (PSS) as polyanions, we found that binding of Co(2+) and Cu(2+) ions with a PEM matrix can occur both through coordination to polycationic amino groups and/or ionic binding to polyacid groups. The amount of metal ions loaded within the film increased linearly with film thickness and was strongly dependent on polyelectrolyte type, film assembly pH, and fraction of permanent charge in polymer chains. Among various PEM-Me(2+) systems, BPEI/PAA-Co(2+) films assembled at pH 8.5 show the best catalytic performance, probably because of the preservation of high mobility of Co(2+) ions coordinated to amino groups of BPEI in these films. With BPEI/PAA-Co(2+) films, we demonstrated that films were highly permeable to reagents and reaction products within hundreds of nanometers of the film bulk; i.e., film catalytic activity increased linearly with layer number up to 30 bilayers and slowed for thicker films.     

Controlling the nanofiltration properties of multilayer polyelectrolyte membranes through variation of film composition

We report the use of a variety of polyelectrolyte multilayers (PEMs) as selective skins in composite membranes for nanofiltration (NF) and diffusion dialysis. Deposition of PEMs occurs through simple alternating adsorption of polycations and polyanions, and separations can be optimized by varying the constituent polyelectrolytes as well as deposition conditions. In general, the use of polycations and polyanions with lower charge densities allows separation of larger analytes. Depending on the polyelectrolytes employed, PEM membranes can remove salt from sugar solutions, separate proteins, or allow size-selective passage of specific sugars. Additionally, because of the minimal thickness of PEMs, NF pure water fluxes through these membranes typically range from 1.5 to 3 m3/(m2 day) at 4.8 bar. Specifically, to separate sugars, we employed poly(styrene sulfonate) (PSS)/poly(diallyldimethylammonium chloride) (PDADMAC) films, which allow 42% passage of glucose along with a 98% rejection of raffinose and a pure water flux of 2.4 m3/(m2 day). PSS/PDADMAC membranes are also capable of separating NaCl and sucrose (selectivity of approximately 10), while high-flux chitosan/hyaluronic acid membranes [pure water flux of 5 m3/(m2 day) at 4.8 bar] may prove useful in protein separations.     

Formation and dielectric properties of polyelectrolyte multilayers studied by a silicon-on-insulator based thin film resistor

The formation of polyelectrolyte multilayers (PEMs) is investigated using a silicon-on-insulator based thin film resistor which is sensitive to variations of the surface potential. The buildup of the PEMs at the silicon oxide surface of the device can be observed in real time as defined potential shifts. The influence of polymer charge density is studied using the strong polyanion poly(styrene sulfonate), PSS, combined with the statistical copolymer poly(diallyl-dimethyl-ammoniumchloride-stat-N-methyl-N-vinylacetamide), P(DADMAC-stat-NMVA), at various degrees of charge (DC). The multilayer formation stops after a few deposition steps for a DC below 75%. We show that the threshold of surface charge compensation corresponds to the threshold of multilayer formation. However, no reversion of the preceding surface charge was observed. Screening of polyelectrolyte charges by mobile ions within the polymer film leads to a decrease of the potential shifts with the number of layers deposited. This decrease is much slower for PEMs consisting of P(DADMAC-stat-NMVA) and PSS as compared to PEMs consisting of poly(allylamine-hydrochloride), PAH, and PSS. From this, significant differences in the dielectric constants of the polyelectrolyte films and in the concentration of mobile ions within the films can be derived.     

Tuning smart microgel swelling and responsive behavior through strong and weak polyelectrolyte pair assembly

The layer-by-layer (LbL) assembly of polyelectrolyte pairs on temperature and pH-sensitive cross-linked poly(N-isopropylacrylamide)-co-(methacrylic acid), poly(NIPAAm-co-MAA), microgels enabled a fine-tuning of the gel swelling and responsive behavior according to the mobility of the assembled polyelectrolyte (PE) pair and the composition of the outermost layer. Microbeads with well-defined morphology were initially prepared by synthesis in supercritical carbon dioxide. Upon LbL assembly of polyelectrolytes, interactions between the multilayers and the soft porous microgel led to differences in swelling and thermoresponsive behavior. For the weak PE pairs, namely poly(L-lysine)/poly(L-glutamic acid) and poly(allylamine hydrochloride)/poly(acrylic acid), polycation-terminated microgels were less swollen and more thermoresponsive than native microgel, whereas polyanion-terminated microgels were more swollen and not significantly responsive to temperature, in a quasi-reversible process with consecutive PE assembly. For the strong PE pair, poly(diallyldimethylammonium chloride)/poly(sodium styrene sulfonate), the differences among polycation and polyanion-terminated microgels are not sustained after the first PE bilayer due to extensive ionic cross-linking between the polyelectrolytes. The tendencies across the explored systems became less noteworthy in solutions with larger ionic strength due to overall charge shielding of the polyelectrolytes and microgel. ATR FT-IR studies correlated the swelling and responsive behavior after LbL assembly on the microgels with the extent of H-bonding and alternating charge distribution within the gel. Thus, the proposed LbL strategy may be a simple and flexible way to engineer smart microgels in terms of size, surface chemistry, overall charge and permeability.     

Novel solid-state polymer electrolyte consisting of a porous layer-by-layer polyelectrolyte thin film and oligoethylene glycol

A novel solid-state polymer electrolyte was constructed using layer-by-layer (LbL) polyelectrolyte assembly of linear poly(ethylenimine) (LPEI) and poly(acrylic acid) (PAA), combined with a plasticization step using oligoethylene glycol dicarboxylic acid (OEGDA). This composite film exhibits a relatively high ionic conductivity of 9.5 x 10(-5) S/cm at 25 degrees C and 22% relative humidity. Detailed characterization of the composite was undertaken using grazing-angle Fourier transform infrared (GA-FTIR), atomic force microscopy (AFM), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and impedance spectroscopy. After immersing the LPEI/PAA films into OEGDA aqueous solutions, the films exhibited a swelling behavior and increased surface roughness indicative of porosity induced by reorganization of ionic interactions between LPEI and PAA in acidic solution. This internal porous structure allows inclusion of OEGDA within the multilayer and increased ionic conductivity under ambient conditions due to the combined effects of plasticization of the LbL matrix by atmospheric water as well as the added mobility of ions in molten OEGDA within the composite.     

Fabrication of Covalently Linked PAH/PVS Layer-by-layer Assembled Multilayers via a Post-photochemical Cross-linking Strategy

A post-photochemical cross-linking strategy was successfully demonstrated to enhance the stability of polyelectrolyte poly(allylamine hydrochloride)(PAH)/poly(vinylsulfonic acid sodium salt)(PVS) multilayers. Conventional polyelectrolyte multilayers of PAH/PVS are usually fabricated through electrostatic layer-by-layer(LbL) assembly, resulting in poor stability, especially in basic solutions, which leads to the urgent demand for converting weak electrostatic interactions into covalent bonds to enhance the stability of the multilayers. This stability problem has been ultimately addressed by post-infiltrating a photosensitive cross-linking agent, 4,4'-diazostilbene-2,2'- disulfonic acid disodium salt(DAS), into the LbL assembled films to initiate the photochemical reaction to cross-link the multilayers. The obviously improved stability of the photo-cross-linked multilayers was demonstrated through experiments with basic solution treatments. Compared to the complete decomposition of uncross-linked multilayers in basic solution, over 74.4% of the covalently cross-linked multilayers were retained under the same conditions, even after a longer duration of basic solution treatment.     

Multicompartment films made of alternate polyelectrolyte multilayers of exponential and linear growth

The layer by layer deposition process of polyelectrolytes is used to construct films equipped with several compartments containing "free polyelectrolytes". Each compartment corresponds to a stratum of an exponentially growing polyelectrolyte multilayer film, and two consecutive compartments are separated by a stratum composed of a linearly growing multilayer that acts as a barrier preventing polyelectrolyte diffusion from one compartment to another. We use hyaluronic acid/poly(L-lysine) as the system to build the compartments and the poly(styrene sulfonate)/poly(allylamine) system for the barrier. Using confocal microscopy, it is shown that poly(L-lysine) diffuses only within the compartment in which it was initially introduced during the film construction and is thus unable to cross the barriers. Using fluorescein isothiocyanate as a pH indicator, it is also shown that although poly(styrene sulfonate)/poly(allylamine) multilayers act as a barrier for polyelectrolytes, they do not prevent proton diffusion through the film. Such films open the route for multiple functionalization of biomaterial coatings.