Anodic stripping voltammetry at a micro-disc mercury film electrode: Theory of the reversible case

For p=(ar²/D_O)^1/2<0.12 and H=al²/D_R<0.14, simple theoretical equations are proposed to characterize the reversible anodic stripping voltammetric peaks of amalgams obtained with a micro-disc mercury film electrode. The calculated, normalized peaks were higher, thinner and shifted towards more negative potentials compared with the peaks described for the regular size mercury film electrodes. The ADI method was used in calculations.     

Electrode Modified with Langmuir–Blodgett (LB) Film of Calixarenes for Preconcentration and Stripping Analysis of Hg(II)

A new type of current sensor, Langmuir–Blodgett (LB) film of calixarene on the surface of glassy carbon electrode (GCE) was prepared for determination of mercury by anodic stripping voltammetry (ASV). An anodic stripping peak was obtained at 0.15 V (vs. SCE) by scanning the potential from ?0.6 to +0.6 V. Compared with a bare GCE, the LB film coated electrode greatly improves the sensitivity of measuring mercury ion. The fabricated electrode in a 0.1 M H₂SO₄+0.01 M HCl solution shows a linear voltammetric response in the range of 0.07–40 μg L^?1 and detection limit of 0.04 μg L^?1 (ca. 2×10^?10 M). The high sensitivity, selectivity, and stability of this LB film modified electrode demonstrates its practical application for a simple, rapid and economical determination of Hg²⁺ in a water sample.     

Square-wave anodic stripping voltammetry with a mercury-plated reticulated vitreous carbon electrode

A rotating mercury-plated reticulated vitreous carbon (RVC) electrode is tested for square-wave anodic stripping voltammetry; RVC provides very large surface areas which are easily plated with mercury. Despite the ill-defined geometry of the electrode, the square-wave stripping peaks are very well defined; their behaviour conforms partly to known theory for square-wave stripping from mercury film electrodes. Fast analytical determinations of lead and cadmium in the μg l^?1 range are facilitated by the high efficiency of the preconcentration step and the high sensitivity given by the stripping waveform.     

Coal as a New Carbon Paste Electrode Modifier with Sorption Properties

A new type of carbon paste electrode modified with subbituminous and bituminous coal is presented. The operability of the coal carbon paste electrode with respect to the working potential window attainable was tested in various electrolytes. Cyclic voltammetry of the reference redox system [Fe(CN)₆]^3?/4? was performed to evaluate electron transfer kinetics. Open‐circuit sorption of Cd(II), Pb(II), and Cu(II) with subsequent anodic stripping voltammetry was used to pilot coal sorption ability. The coal modified carbon paste electrode was also examined as a support for mercury film deposition and anodic stripping voltammetry of metals.     

Anodic stripping voltammetry at a mercury film electrode: baseline concentrations of cadmium,lead, and copper in selected natural waters

A simple, rapid, and inexpensive anodic stripping voltammetric method with a mercury thin film electrode is reported for the establishment of baseline concentrations of cadmium, lead, and copper in natural waters. The procedure for routine surface preparation of wax-impregnated graphite mercury film electrodes requires about 30 min. Concentrations in the 0.006–6 μg l^-1 range are determined by linear d.c. voltage sweeps; the total time for a plating and stripping cycle is 6 min or less. The need for pressure-digesting samples for copper determinations is demonstrated. The a.s.v. results correlate well with corresponding analyses performed by graphite-furnace atomic absorption spectrometry.     

Anodic stripping voltammetry at a nickel-based mercury film electrode

The electrochemical properties of the nickel-based mercury film electrode (Ni-MFE) were investigated with respect to application of the electrode in the anodic stripping voltammetry (a.s.v.) of heavy metal ions. The hydrogen overpotential at the Ni-MFE is higher than those at MFEs based on other metals, and high enough to get quantitative a.s.v. peaks of lead and cadmium. The mercury film of the Ni-MFE is stable both mechanically and chemically; a.s.v. peaks at a Ni-MFE which had been used fifty times within 300 h after its preparation were identical with those at the freshly prepared electrode. With the Ni-MFE, 5 × 10^?10–10^?7 M lead(II) and 2 × 10^?10–10^?7 M cadmium(II) in the solution can be determined with relative standard deviations of 11 and 12%, respectively. These results are comparable to those obtained by a.s.v. at an in situ mercury-plated g]assy carbon electrode.     

L'electrode a Pate de Carbone Modifiee Son Utilisation en Voltammetrie par Redissolution Anodique a Impulsions Differentielles en Presence d'Un Film de Mercure

Abstract

The various problems which are associated with the use of carbon paste electrode as thin mercury film electrode (TKFE) for anodic stripping voltammetry (ASV) can be overcame in a very easy and rapid way. The procedure consists to coat the carbon paste surface by spraying a graphite based conductive solution. For example, the dispersion of colloidal graphite in a mixture of methyl polymethacrylate with butyl acetate (as solvent) gives interesting results. Such a surface is easily renewable and the electrode does not require any pretreatment procedure like cleaning or polarization cycles…, after coating. The technique offers the advantage to limit the risk of sample contamination and memory effects. After pulverisation, a hard, uniform and compact layer is formed after evaporation of the solvent excess.

The resulting electrode, electrochemically coated with mercury, exhibits a good stability as shown for the differential pulse anodic stripping voltammetry (DPASV) for cadmium ions. Replicate measurements were carried out in two different buffers at pH 8.5 and 5.0. Compared to the originally carbon paste electrode, a marked improvement of the reproducibility of the peak currents is observed. Calibration curves obtained by using the method of standard additions show a good linear relationship between cadmium ions concentration and peak current (down to 4×10^?10 M.L^?1).

After a deposition time of 10 minutes, the detection limit for cadmium is 1×10^?10 M.L^?l in both media).     

Quantitative determination of zinc in milkvetch by anodic stripping voltammetry with bismuth film electrodes

Bismuth film electrode (BiFE) was shown to be an attractive alternative to common mercury film electrode (MFE) for anodic stripping voltammetric measurements. In this study, bismuth film, that was in situ deposited onto glassy carbon electrode, was used to detect zinc content of milkvetch, used in traditional Chinese medicine. Variables affecting the response have been evaluated and optimized. Experimental results showed a high response, with a good linearity (between 0.5 × 10⁻⁶ mol L⁻¹ and 3 × 10⁻⁶ mol L⁻¹) a good precision (R.S.D. = 3.58%) and a low detection limit (9.6 × 10⁻⁹ mol L⁻¹ with a 120 s anodic). The anodic stripping performance makes the bismuth film electrode very desirable for measurements of trace nutritive element zinc in milkvetch and should impart possible restrictions on the use of mercury electrode.     

Over‐Oxidized Poly (Phenol Red) Film Modified Glassy Carbon Electrode for Anodic Stripping Voltammetric Determination of Ultra‐Trace Antimony (III)

In this study, we introduce a very sensitive and selective method for the differential pulse anodic stripping determination of Sb(III) ion on the over‐oxidized poly(phenol red) modified glassy carbon electrode (PPhRed_ox/GCE) in 0.1 mol L^‐1 HCl medium. The formation of both poly(phenol red) and over‐oxidized poly(phenol red) film on the electrode surfaces were characterized by electrochemical impedance spectroscopy, X‐ray photoelectron spectroscopy and scanning electron microscopy techniques. An anodic stripping peak of Sb(III) was observed at 0.015 V on the PPhRed_ox/GCE. Higher anodic stripping peak current of Sb(III) was obtained at PPhRed_ox/GCE compared with both bare GCE and poly(phenol red) film modified GCE (PPhRed/GCE). The calibration graph consisted of two linear segments of 0.044 ‐ 1.218 μg L⁻¹ and 3.40 – 18.26 μg L⁻¹ with a detection limit of 0.0075 μg L⁻¹. The proposed over‐oxidized polymer film modified electrode was applied successfully for the analysis of antimony in different spiked water samples. Spiked recoveries for water samples were obtained in the range of 93.0–103.0%. The accuracy of the method was also verified through the analysis of standard reference materials (SCP SCIENCE‐EnviroMAT™ EP−L‐2).     

Assessment of the Stability of a Mercury Film on a Glass–Ceramic Carbon Electrode when Determining Zinc in the Presence of Manganese by Anodic Stripping Voltammetry

The possibility of assessing the stability of operation of a mercury film graphite electrode in anodic stripping voltammetry using Shewhart control charts (CCs) is shown. The offered technique allows significantly increasing the efficiency of the voltammetric determination of zinc and manganese and taking measurements of analytes in samples during a working day without replacing the mercury film on the electrode surface.     

Stripping Voltammetry of Mercury(II) with a Chemically Modified Carbon Paste Electrode Containing Silica Gel Functionalized with 2,5‐Dimercapto‐1,3,4‐thiadiazole

The accumulation voltammetry of mercury(II) was investigated at a carbon paste electrode chemically modified with silica gel functionalized with 2,5‐dimercapto‐1,3,4‐thiadiazole (DTTPSG‐CPE). The repetitive cyclic voltammogram of mercury(II) solution in the potential range ?0.2 to +0.8 V (vs. Ag/AgCl), (0.02 mol L^?1 KNO₃ ; v=20 mV s^?1) show two peaks one at about 0.0 V and other at 0.31 V. However, the cathodic wave peak, around 0.0 V, is irregular and changes its form in each cycle. This peak at about 0.0 V is the reduction current for mercury(II) accumulated in the DTTPSG‐CPE. The anodic wave peak at 0.31 V is well‐defined and does not change during the cycles. The resultant material was characterized by cyclic and differential pulse anodic stripping voltammetry performed with the electrode in differents supporting electrolytes. The mercury response was evaluated with respect to pH, electrode composition, preconcentration time, mercury concentration, “cleaning” solution, possible interferences and other variables. The precision for six determinations (n=6) of 0.05 and 0.20 mg L^?1 Hg(II) was 2.8 and 2.2% (relative standard deviation), respectively. The method was satisfactory and used to determine the concentration of mercury(II) in natural waters contaminated by this metal.     

Electrodeposition of mercury film on electrodes modified with clay minerals

A new type of carbon paste electrode modified with clay mineral and covered with a mercury film is presented in this work. Electrodeposition of the mercury film was performed on the carbon paste electrode modified with montmorillonite. The mercury film was deposited by both electrodeposition in situ and a preliminary electrodeposition. The pre-deposited film of mercury showed to be suitable for anodic stripping voltammetry. An open-circuit sorption of Cd, Pb, and Cu with subsequent anodic stripping voltammetry exhibited higher current responses of metals. Besides the enhanced sensitivity superior separation of the current responses during a simultaneous stripping of metals is expected to be achieved by means of the newly prepared electrode. Presented at the 57th Congress of Chemical Societies, Tatranské Matliare, 4–8 September 2005.     

Anodic Stripping Voltammetry Determination of Pb(II) and Cd(II) at a Bismuth/Poly(aniline) Film Electrode

Abstract

A novel voltammetric method—anodic—using a bismuth/poly(aniline) film electrode has been developed for simultaneous measurement of Pb(II) and Cd(II) at low µg L^?1 concentration levels by stripping voltammetry. The results confirmed that the bismuth/poly(aniline) film electrode offered high‐quality stripping performance compared with the bismuth film electrode. Well‐defined sharp stripping peaks were observed for Pb(II) and Cd(II), along with an extremely low baseline. The detection limits of Pb(II) and Cd(II) are 1.03 µg L^?1 and 1.48 µg L^?1, respectively. The bismuth/poly (aniline) electrode has been applied to the determination of Pb(II) in tap water samples with satisfactory results.     

Interfering influence of silver on the voltammetric behaviour of Cd2+ and Zn2+ ions on hmde in supporting electrolytes containing nitrates

A new kind of secondarily formed peaks was found in cyclic and stripping voltammetry in neutral sulphate, perchlorate and nitrate supporting electrolytes containing some divalent cations and a substance (for example O₂), the reduction of which gives as a by-product OH^? ions. The hydroxides deposited in the vicinity of the mercury electrode, in the course of a cathodic scan, react during the anodic scan according to the reaction Hg+Me(OH)₂=Hg(OH)₂+Me²⁺+2e forming a new, separate anodic peak.It was found that silver exerts a catalytic effect on the reduction of NO₃^? ions on the mercury electrode. In neutral nitrate supporting electrolyte containing Ag⁺ ions the hydroxides of some cations (Cd²⁺, Zn²⁺, Mn²⁺, Co²⁺ and Ni²⁺) were deposited during the cathodic scan or during the preelectrolysis. Afterwards, in the course of the anodic scan, a new peak, of the kind described above, was observed. The same effect was formerly interpreted, for Zn²⁺ and Cd²⁺, as evidence for the formation of intermetallic compounds, AgZn and AgCd.     

Silver based mercury film electrode: Part II. The influence of aging of electrode on the electrode processes of various metal ions

The cyclic voltammetric behaviour of 8 metal ions at solid silver amalgam electrodes prepared by aging of a thin silver based mercury film electrode (SBMFE) and by deposition of silver and mercury on platinum were investigated. It was established that such electrodes behave in relation to some metals (Pb, Bi, Sn) similarly as silver electrodes i.e. the cyclic curves obtained with these electrodes at concentration 10^?3M range show a prepeak-postpeak system corresponding to deposition and dissolution of the monolayer of deposit. On the other hand under the same conditions no prepeaks were observed for cadmium, zinc and thallium. In all cases investigated the heights of anodic stripping peaks were lower on curves obtained with aged SBMFE than on those obtained with fresh SBMFE having a mercury layer 1 μm thick.     

The use of Nafion-coated thin mercury film electrodes for the determination of the dissolved copper speciation in estuarine water

Differential pulse anodic stripping voltammetry (DPASV) using a Nafion-coated thin mercury film electrode (NCTMFE) was implemented to determine the dissolved copper speciation in saline estuarine waters containing high concentrations of dissolved organic matter (DOM). The study used model ligands and estuarine water from San Francisco Bay, California, USA to demonstrate that the NCTMFE is more effective at distinguishing between electrochemically inert and labile copper species when compared to the conventional thin mercury film electrode (TMFE). Copper titration results verify that the NCTMFE better deals with high concentrations of DOM by creating a size-exclusion barrier that prevents DOM from interacting with the mercury electrode when performing copper speciation measurements. Pseudovoltammograms were used to illustrate that copper complexes found in natural waters were more apt to be electrochemically inert at the NCTMFE relative to the TMFE when subjected to high negative overpotentials. Copper speciation results using the NCTMFE from samples collected in San Francisco Bay estimated that >99.9% of all copper was bound to strong copper-binding ligands. These L₁-class ligands exceeded the concentration of total dissolved copper in all samples tested and control the equilibrium of ambient [Cu²⁺] in the San Francisco Bay estuary.     

Use of a modified, high-sensitivity, anodic stripping voltammetry method for determination of zinc speciation in the North Atlantic Ocean

Zinc speciation is considered to be an important determinant of the biological availability of zinc. Yet in oceanic surface waters, characterization of zinc speciation is difficult due to the low concentrations of this essential micronutrient. In this study, an anodic stripping voltammetry method previously developed for the total determination of cadmium and lead was successfully adapted to the measurement of zinc speciation. The method differs from previous zinc speciation anodic stripping voltammetry methods in that a fresh mercury film is plated with each sample aliquot. The fresh film anodic stripping voltammetry method was compared to competitive ligand exchange cathodic stripping voltammetry in a profile from the North Atlantic Ocean. Results using the fresh film anodic stripping voltammetry method were similar to those determined using the cathodic stripping voltammetry method, though ligand concentrations determined by fresh film anodic stripping voltammetry were generally slightly higher than those determined by cathodic stripping voltammetry. There did not seem to be a systematic difference between methods for the estimates of conditional stability constants. The ligand concentration in the North Atlantic profile ranged from 0.9 to 1.5 nmol L⁻¹ as determined by fresh film anodic stripping voltammetry and 0.6 to 1.3 nmol L⁻¹ as determined by cathodic stripping voltammetry. The conditional stability constants determined by fresh film anodic stripping voltammetry were 10^9.8-10^10.5 and by cathodic stripping voltammetry were 10^9.8-10^11.3.     

Simultaneous determination of copper and lead in seawater using optimised thin-mercury film electrodes in situ plated in thiocyanate media

In the present work the anodic stripping voltammetric (ASV) methodology using a thin mercury film electrode in situ plated in thiocyanate media was re-assessed in order to allow the simultaneous determination of copper and lead in seawater. Under previously suggested conditions [6], i.e. using a concentration of thiocyanate of 5 mM, the ASV peaks of copper and lead overlapped due to the formation of a stable copper(I)-thiocyanate species, limiting the analytical determinations. Therefore, the best value for the thiocyanate concentration was re-evaluated: for 0.05 mM a trade-off between good resolution of the copper and lead peaks and high reproducibility of the mercury film formation/removing processes was achieved. In this media, the ASV peaks for Pb and Cu occurred, separated by 140 mV. Also, the in situ thin mercury film electrode was produced and removed with good repeatability, which was confirmed by the relative standard deviation values for the ASV determinations: 0.5% for Pb and 2.0% for Cu (10 replicate determinations in a solution with metal concentrations 1.5×10⁻⁸ M for lead and 2.2×10⁻⁸ M for copper). The optimised methodology was successfully applied to the determination of copper in the presence of lead, in certified seawater (NASS-5).     

Cathodic stripping voltammetry: Part I. Determination of organic sulfur compounds,flavins and porphyrins at the sub-micromolar level

The experimental parameters of cathodic stripping voltammetry have been studied and optimised, and the use of a cell with a mercury pool electrode has been proposed. The technique is valuable for the determination of several classes of organic compounds, including thiols, disulfides, flavins, flavones, pterins and porphyrins at concentrations as low as 1×10^?8M. In most cases the measurement precision at the 2×10^?7M level is ±3–5%, which is similar to that of anodic stripping voltammetry. Detailed investigations were made of the electrode reaction mechanisms of cysteine, cystine, riboflavin and hemoglobin. All thiol compounds were found to adsorb strongly on mercury and chemically react with it to form a film of a mercury-thiol compound. Some closely-related thiols, e.g. 2- and 6-mercaptopurine, produced stripping peaks at well-separated potentials. Selectivity could be achieved with some thiol mixtures by adjustment of the deposition potential.     

Application of a copper-based mercury film electrode in cathodic stripping voltammetry

The utility of a copper-based mercury film electrode (MFE) in cathodic stripping voltammetry (c.s.v.) is tested by comparing the cyclic and stripping voltammograms obtained with this electrode for thiocyanate, tryptophane, cysteine and benzotriazole against those obtained with the hanging copper-amalgam drop electrode (HCADE) and the HMDE. The cathodic stripping peaks obtained at the copper-based MFE and the HCADE are usually narrower and higher and are located at more negative potentials than the peaks obtained at the HMDE. Lower detection limits and better separations of adjacent peaks are thus achieved, and useful peaks can be separated from the mercury waves obtained with the conventional HMDE. The advantage of the copper-based MFE over the HCADE is its simplicity of preparation and maintenance. Thiocyanate, tryptophane, cysteine and benzotriazole can be determined at the copper-based MFE by c.s.v. with detection limits of 1 × 10^?8, 1 × 10^?8, 5 × 10^?8 mol dm^?3, respectively.