流动注射化学发光法测定司帕沙星的研究

在酸性介质中,司帕沙星对NaNO2-H2O2发光体系有很强的增强作用,并且其增强化学发光强度与司帕沙星的物质的量浓度在一定范围内呈线性关系。基于此,采用流动注射技术,建立了一种简单、快速测定司帕沙星的方法。线性范围为1.0×10-7~8.5×10-4mol/L,检出限为6.5×10-8mol/L。利用该法测定了司帕沙星片剂中的司帕沙星,回收率在98.8%~104.4%之间。     

流动注射化学发光法测定那格列奈

在碱性介质中,那格列奈对Luminol-H2O2体系的化学发光有很强的抑制作用,据此建立了流动注射化学发光抑制法测定那格列奈的新方法.该法的化学发光抑制值△I与那格列奈的质量浓度在2.0×10-8～1.0×10-6 g/mL范围内,呈良好的线性关系,检出限为1.4×10-8 g/mL;对4.0×10-7 g/mL那格列奈连续进行11次平行测定,相对标准偏差为1.0%;通过对荧光光谱的研究,对机理进行了初步探讨.     

流动注射化学发光法测定佐米曲谱坦

在碱性条件下,佐米曲谱坦对鲁米诺-K3[Fe(CN)6]化学发光体系有较强的抑制作用,据此建立了佐米曲谱坦的流动注射化学发光分析法。该法的化学发光抑制值ΔI与佐米曲谱坦质量浓度在2.0×10-6~1.2×10-4g/mL范围内,呈良好的线性关系,检出限为7.6×10-7g/mL。对2.5×10-5g/mL佐米曲谱坦测定的相对标准偏差为1.2%(n=11)。方法适用于佐米曲谱坦片中佐米曲谱坦的测定。     

流动注射化学发光法测定氨苄西林的研究

氨苄西林在NaOH溶液中降解后,其产物可在酸性条件下与KMnO4发生化学发光反应,甲醛的存在可使发光强度增强。据此,采用流动注射技术,建立了一种测定氨苄西林的化学发光分析法。方法的检出限为9.1×10-9g/mL,相对标准偏差为1.8%(n=11,ρ=3.4×10-6g/mL),线性范围为4.0×10-8~2.0×10-5g/mL。利用该法测定了氨苄西林胶囊中的氨苄西林,其回收率在87%~106%。     

Chemiluminescence determination of bufrenorphine hydrochloride by flow injection analysis

A direct, simple and rapid flow-injection method is described for determining buprenorphine hydrochloride (10^?8–10^?4 M) based on its chemiluminescent oxidation with potassium permanganate in polyphosphoric acid. The limit of detection is 1 × 10^?8 M (0.5 pmol per injection) and the log-log calibration is linear up to 1 × 10^?4 M; the r.s.d. is 0.7% for a 10 μg ml^?1 solution (n = 10). The method is directly applicable to aqueous solutions of tablets containing the drug (0.2 mg/tablet).     

Chemiluminescence determination of nitrate with photochemical activation in a flow injection system

A chemiluminescence flow injection system is described for the determination of nitrate, involving use of a laboratory-built flow-through photochemical reactor. Optimum analytical conditions were established. The linear range for nitrate is 7 x 10(-8)-1 x 10(-4)M. The sampling frequency is 60 samples per hour. The relative standard deviation for 1 x 10(-7), 1 x 10(-6) and 1 x 10(-5)M nitrate is 0.97, 0.84 and 0.76%, respectively. The method has been applied to the determination of nitrate in natural water samples, and recoveries of 96-103% have been attained.     

流动注射化学发光法快速测定化学需氧量

基于酸性K2 Cr2 O7在消解水体中的有机污染物时被还原为Cr(Ⅲ ) ,而Cr(Ⅲ )可以催化Luminol H2 O2 体系产生强的化学发光 ,建立了一种测定COD的流动注射化学发光法。本方法不需要催化剂 ,不需要长的消解时间 ,可以采用较低的酸度 ,适合于在线连续检测水体COD。本方法检测COD的线性范围为 2 0～1 0 0 0 0mg L ,检出限为 1 0mg L ,对 1 0mg LCOD的 1 1次平行测定的RSD小于5 %。方法已用于地表水样COD的测定。     

Chemiluminescence system for automatic determination of chemical oxygen demand using flow injection analysis

A novel chemiluminescence (CL) system for automatic determination of chemical oxygen demand (COD) combined with flow injection analysis is proposed in this paper. In this system, potassium permanganate is reduced to Mn²⁺ which is first adsorbed on a strongly acid cation-exchange resin mini-column to be concentrated during chemical oxidation of the organic compounds at room temperature, while the excessive MnO₄⁻ passes through the mini-column to be waste, then the concentrated Mn²⁺ is eluted reversely and measured by the luminol-H₂O₂ CL system. The calibration graph is linear in the range of 4-4000 mg l⁻¹ and the detection limit is 2 mg l⁻¹. A complete analysis could be performed in 1.5 min including washing and sampling, giving a throughout of about 40 h⁻¹. The relative standard deviation was 4.4% for 10 mg l⁻¹ COD (n=11), 4.8% for 100 mg l⁻¹ COD (n=11). This CL flow system for determination of COD is very simple, rapid and suitable for automatic and continuous analysis. The presented system has been applied successfully to the determination of COD of water samples.     

Chemiluminescence detection of sodium nitroprusside using flow injection analysis

A simple continuous-flow chemiluminometric method for the determination of 0.05-10 microg/ml of sodium nitroprusside is described. The method is based on the catalyses of luminol oxidation by hydrogen peroxide in alkaline medium. The method is sensitive and requires no sample pre-treatment and solutions can be analysed at a rate of 40 samples/hr with a relative error of about 1.18%. The method was satisfactory for the determination of sodium nitroprusside in a pharmaceutical preparation. The effect of some potential interferents is described.     

Chemiluminescence determination of indole derivatives in human body fluids and soil by flow injection analysis using potassium permanganate

A simple, sensitive and rapid flow-injection chemiluminescence (CL) method has been developed for the determination of indole derivatives including indole-2,3-dione (isatin) and indole-3-acetic acid (IAA), based on the increased CL reaction of potassium permanganate-formaldehyde system in acidic medium. Strong CL was observed when the indole derivatives were injected into the acidic potassium permanganate solution in a flow-cell. Under the optimum conditions, the linear range of the determination was 0.1–100.0 µM for isatin and 0.01–10.0 µM for IAA. The detection limit (3σ) was 10.0 nM for isatin and 1.0 nM for IAA. The method has been successfully applied to the determination of isatin in biological samples and of IAA in biological samples and soil extracts with satisfactory results.     

Use of photochemical reactions in flow injection: determination of oxalate in urine

The use of photochemical reactions in flow injection (FI) is reported. The irradiation of an FI reactor with a suitable source facilitates the development of the iron(III)-oxalate reaction, allowing the amperometric determination of the anion in the range 1.0-13.0 micrograms ml-1, with a relative standard deviation of 1.1% and a sampling frequency of 40 h-1. The proposed method was applied successfully to the determination of oxalate in urine samples.     

Chemiluminescence determination of carbofuran at trace levels in lettuce and waters by flow-injection analysis

A simple, fast chemiluminescence (CL) flow-injection (FI) method based on the reaction of luminol with KMnO₄ in alkaline medium has been described for the direct determination of carbofuran. The method is based on the enhancing effect in the emission light from the oxidation of luminol produced in presence of carbofuran. The optimisation of instrumental and chemical variables influencing the CL response of the method has been carried out by applying experimental design, using the proposed flow-injection manifold. Under the optimal conditions, the CL intensity was linear for a carbofuran concentration over the range of 0.06-0.5 μg ml⁻¹, with a detection limit of 0.02 μg ml⁻¹. The method has been successfully applied to the determination of carbofuran residues in spiked water and lettuce samples.     

Chemiluminescence determination of sodium 2-mercaptoethane sulfonate by flow injection analysis using cerium(IV) sensitized by quinine

A flow injection method with chemiluminescence (CL) detection is proposed for the determination of sodium 2-mercaptoethane sulfonate (MESNA), a drug often used to reduce the urotoxic effects of antineoplastic alkylating agents. The procedure is based on the reaction of the thiol with Ce(IV) in a sulfuric acid medium and measurement of the CL intensity produced by quinine used as a sensitizer. The optimum conditions for CL emission were investigated. Using the CL peak height as the analytical parameter, MESNA was determined over the concentration range 0.29–2.21 ng (1.97–9.85 μg·l⁻¹) with a detection limit of 0.21 ng (1.38 μg·l⁻¹) and a relative standard deviation (R.S.D.) of 4.1%. The method was applied satisfactorily to the determination of MESNA in pharmaceutical preparations with percentages of recovery between 94 and 105.     

Chemiluminescence determination of iron(II) and titanium(III) by flow injection analysis based on reactions with and without luminol

Titanium(III) and iron(II) are shown to stimulate luminol chemiluminescence in the absence of added oxidant. Down to 10^?9 M titanium can be determined. Both metal ions also produce chemiluminescence when injected into 0.1 M carbonate buffer (pH 10.4), allowing >10^?6 M of each to be determined. The intensities are greater when the solutions have been deoxygenated by a stream of nitrogen, and when rhodamine B is used as a sensitizer.     

Chemiluminescence determination of gossypol at trace levels using flow injection as sample introduction techniques

A simple and sensitive flow injection method with chemiluminescence (CL) detection is developed for the determination of gossypol at trace levels. The method is based on the reaction of luminol with ferricyanid in a sodium hydroxide medium sensitized by gossypol. Under the optimum conditions, the CL intensity is proportional to the concentration of gossypol over the range of 1.11 × 10⁻¹⁷ − 2.78 × 10⁻¹⁶ M in an acidic solution and 8.00 × 10⁻¹¹ − 7.39 × 10⁻⁸ M in a neutral solution with correlation coefficients of 0.9983 and 0.9905, respectively. The detection limit is 1.48 × 10⁻¹⁸ M (3σ). The proposed method has been applied to the determination of gossypol in cottonseeds and pharmaceutical preparations with satisfactory results. The CL mechanism is discussed by examining the CL emission spectrum and the effect of various free radical scavengers on the CL emission intensity. The text was submitted by the authors in English.     

Chemiluminescence for the determination of traces of cobalt(II) by continuous flow and flow injection methods

Flow injection analysis, with chemiluminescence detection, is used to determine traces of cobalt(II) by means of the gallic acid—hydrogen peroxide—sodium hydroxide system containing a small amount of methanol to increase the sensitivity. This permits the determination of cobalt(II) more selectively than any other chemiluminescent system with a detection limit of 0.04 μg l^-1 (continuous sample flow) or 0.04 ng (10-μl sample injection). The linear range is 3 orders of magnitude, the sampling rate is 20 h^-1, and the relative standard deviation is 5.9% for 0.06 ng Co(II) (n = 10). Silver(I), the strongest enhancer after cobalt(II), provides a signal 1.3% of that for Co(II). A few precipitants and complexing agents suppress the signal.     

Chemiluminescence detection flow cells for flow injection analysis and high-performance liquid chromatography

We have examined a range of new and previously described flow cells for chemiluminescence detection. The reactions of acidic potassium permanganate with morphine and amoxicillin were used as model systems representing the many fast chemiluminescence reactions between oxidising agents and organic analytes, and the preliminary partial reduction of the reagent was exploited to further increase the rates of reaction. The comparison was then extended to high-performance liquid chromatography separations of α- and β-adrenergic agonists, with permanganate chemiluminescence detection. Flow cells constructed by machining novel channel designs into white polymer materials (sealed with transparent films or plates) have enabled improvements in mixing efficiency and overall transmission of light to the photodetector.     

Simultaneous determination of nitrate and nitrite by flow injection analysis

An automatic method for the simultaneous determination of nitrate and nitrite by flow injection analysis is described. Nitrate is reduced to nitrite with a copperized cadmium column. Nitrite is diazotized and coupled with N-(l-naphthyl)ethylenediammonium dichloride. The merging zones approach is used to minimize reagent consumption. The injector system is arranged so that two peaks are obtained, one corresponding to nitrite and the other to nitrite plus nitrate. A sampling rate of about 90 samples per hour is possible; the precision is better than 0.5% for nitrite in the range 0.1–0.5 mg l^t and 1.5% for nitrate in the range 1.0–5.0 mg l^t     

Simultaneous spectrophotometric determination of uranium and thorium by flow injection analysis using selective masking.

A flow injection system for the simultaneous determination of uranium and thorium has been developed by using selective masking and a spectrophotometric detector with two flow cells aligned with the same optical path. The injected sample solution was first mixed with a reagent solution containing Chromazurol S (CAS) and cetyltrimethylammonium chloride (CTMAC), and the total absorbance of uranium- and thorium-CAS complexes was measured in the first flow cell at 620 nm. The sample stream was then mixed with an EDTA solution in order to convert the thorium-CAS complex to a thorium-EDTA complex, and the absorbance of the uranium-CAS complex was measured in the second flow cell. The detection limits were 10 microg dm(-3) for uranium and 7 microg dm(-3) for thorium. The calibration graphs were linear (r < 0.9998) at least over the ranges of 0.1 to 10 mg dm(-3) for uranium and 0.08 to 8 mg dm(-3) for thorium. The RSDs were less than 1.5% (n = 3) in the calibration range. Uranium and thorium of up to the 6-fold concentration to each other could be determined in admixtures with relative errors of less than 3.3%. The sample throughput was 24 per hour. The proposed system was successfully applied to the analysis of a uranium-thorium ore mock solution by coupling with anion-exchange in a magnesium nitrate medium to eliminate interference from coexisting elements.