Enhanced Photocurrent Generation in Self-Assembled Monolayers Formed at Plasmonic Gold Nanostructures

The effect of localized surface plasmon resonance (SPR) appearing at the surfaces of gold nanoparticles (AuPs) was successfully applied for the enhancement of photocurrents from porphyrin ( Po ) immobilized on AuPs. The electrode consisting of AuPs with different sizes (∼15 or ∼35 nm) was prepared using the AuP film formed at the liquid/liquid interface, and then Po was self-assembled on the gold surface. The SPR effect for the AuP film was verified from the attenuated total reflection SPR and absorption measurements. Photocurrents from the modified electrodes were compared with the corresponding planar electrode. Appreciable enhancement of photocurrents was observed.     

Enhanced photocurrent generation by photosynthetic bacterial reaction centers through molecular relays, light-harvesting complexes, and direct protein-gold interactions

The utilization of proteins as nanodevices for solar cells, bioelectronics, and sensors generally necessitates the transfer of electrons to or from a conducting material. Here we report on efforts to maximize photocurrent generation by bacterial photosynthetic reaction center pigment-protein complexes (RCs) interfaced with a metal electrode. The possibility of adhering RCs to a bare gold electrode was investigated with a view to minimizing the distance for electron tunneling between the protein-embedded electron-transfer cofactors and the metal surface. Substantial photocurrents were achieved despite the absence of coating layers on the electrode or engineered linkers to achieve the oriented deposition of RCs on the surface. Comparison with SAM-covered gold electrodes indicating enhanced photocurrent densities was achieved because of the absence of an insulating layer between the photoactive pigments and the metal. Utilizing RCs surrounded by light-harvesting 1 complex resulted in higher photocurrents, surprisingly not due to enhanced photoabsorption but likely due to better surface coverage of uniformly oriented RC-LH1 complexes and the presence of a tetraheme cytochrome that could act as a connecting wire. The introduction of cytochrome-c (cyt-c) as a molecular relay also produced increases in current, probably by intercalating between the adhered RCs or RC-LH1 complexes and the electrode to mediate electron transfer. Varying the order in which components were introduced to the electrode indicated that dynamic rearrangements of RCs and cyt-c occurred at the bare metal surface. An upper limit for current generation could not be detected within the range of the illumination power available, with the maximum current density achieved by RC-LH1 complexes being on the order of 25 μA/cm(2). High currents could be generated consecutively for several hours or days under ambient conditions.     

In vacuo photocurrent measurements of plasma polymerized styrene films

Photoconductivity measurements were carried out on plasma polymerized styrene (PPS) in vacuo, in air, and in subsequently re-evacuated conditions. Samples with two gold electrodes (Au-PPS-Au) and gold-aluminum electrodes (Au-PPS-Al) were used. Positive short circuit photocurrents in the direction of illumination were observed in both types of specimens. In the case of Au-PPS-Au, photocurrent threshold was about 1.6 eV in vacuo for the virgin film, which is attributed to the energy of hole generation in bulk. Residual free radicals were assumed to be the acceptors in this mechanism. In the case of Au-PPS-Al, electron injection from aluminum was thought to be a more likely mechanism, with an estimated barrier height of approximately 2.6 eV.     

FeFe]-hydrogenase-catalyzed H2 production in a photoelectrochemical biofuel cell

The Clostridium acetobutylicum [FeFe]-hydrogenase HydA has been investigated as a hydrogen production catalyst in a photoelectrochemical biofuel cell. Hydrogenase was adsorbed to pyrolytic graphite edge and carbon felt electrodes. Cyclic voltammograms of the immobilized hydrogenase films reveal cathodic proton reduction and anodic hydrogen oxidation, with a catalytic bias toward hydrogen evolution. When corrected for the electrochemically active surface area, the cathodic current densities are similar for both carbon electrodes, and approximately 40% of those obtained with a platinum electrode. The high surface area carbon felt/hydrogenase electrode was subsequently used as the cathode in a photoelectrochemical biofuel cell. Under illumination, this device is able to oxidize a biofuel substrate and reduce protons to hydrogen. Similar photocurrents and hydrogen production rates were observed in the photoelectrochemical biofuel cell using either hydrogenase or platinum cathodes.     

Parallel-oriented fibrogenesis of a beta-sheet forming peptide on supported lipid bilayers

Peptide self-assembly on substrates is currently an intensively studied topic that provides a promising strategy for fabrication of soft materials and is also important for revealing the surface chemistry of amyloidogenic proteins that aggregate on cell membranes. We investigated the fibrogenesis of a beta-sheet forming peptide Abeta(26-35) on supported lipid bilayers (SLBs) by in situ atomic force microscopy (AFM), circular dichroism (CD), and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy. The results show that the Abeta(26-35) nanofilaments' growth is oriented to a specific direction and formed a highly ordered, large-scale, parallel-oriented surface pattern on membranes. The parallel-oriented fibrogenesis of Abeta(26-35) was able to occur on different lipid membranes rather than on solid substrates. It implies that the parallel-oriented fibrogenesis was associated with the distinct properties of lipid membranes, such as the fluid nature of lipid molecules on membranes. The membrane fluidity may allow the peptide assemblies to float at the water-membrane interface and easily orient to an energetically favorable state. These results provide an insight into the surface chemistry of peptide self-assembly on lipid membranes and highlight a possible way to fabricate supramolecular architectures on the surface of soft materials.     

Spectral sensitization of SrTiO3 electrodes with magnesium tetraphenylporphene

Spectral sensitization by magnesium tetraphenylporphine (MgTPP) films on SrTiO₃ electrodes is reported, using hydroquinone (HQ) as a reductant. The action spectra reflect the absorption spectra of the MgTPP films. MgTPP films show both anodic and cathodic photocurrents depending on the applied potential. An influence of the structure of the MgTPP films on the photocurrents has been observed.     

Electron transfer reactions of excited ruthenium(II) complexes in monolayer assemblies at the SnO2-water interface

Monolayers of several surfactant analougues of Ru(bipy)$\text{2}\text{3}$⁺ ha ve been deposited on SnO₂ electrodes. Anodic photocurrents were observed when these electrodes were illuminated in (Ru-free) aqueous solutions. The photocurrents are interpreted by an electron transfer from the Ru(II) complex, excited to its triplet state, to the conduction band of SnO₂. The Ru(III) complex formed in this reaction is efficiently reduced by water.     

REACTION OF EXCITED CHLOROPHYLL MOLECULES AT ELECTRODES AND IN PHOTOSYNTHESIS*

Abstract— Excited molecules can exchange electrons with suitable electrodes in an electrochemical cell. Excitation energy of molecules can therefore be converted into electrochemical energy. Electrochemical reactions of excited chlorophyll molecules have been investigated with the help of semiconductor electrodes. It is suggested that this type of reaction also occurs during the primary steps of photosynthesis. Consequently, concepts of electrochemical kinetics would have to be applied in order to elucidate chlorophyll-sensitized reactions in photosynthetic membranes. In order to provide evidence for this conclusion, electrochemical kinetics is applied to the calculation of decay of delayed light from photosynthetic membranes, and the result is compared with experimental data from Chlorella pyrenoidosa. The conversion of light into electrochemical energy via photoelectrochemical reactions of organic dyes in an electrochemical cell is demonstrated, and the postulated analogous electrochemical mechanism for photosynthesis is discussed.     

Electropolymerized polythiophene photoelectrodes with density-controlled gold nanoparticles

A polythiophene thin film was fabricated on gold nanoparticle (AuNP)-deposited indium-tin-oxide (ITO) electrodes with electropolymerization, whereas AuNPs were predeposited on the ITO surface. A photocurrent via photoexcited polythiophene increased with AuNPs which was attributed to the localized surface plasmon resonance. Investigation of the AuNP-density dependence on the relative enhancement of photocurrent revealed the maximum effect at 14% of AuNP-density, while 68% of AuNP-density exhibited smaller photocurrent than the polythiophene electrode without AuNPs. We have revealed that the effects of AuNPs saturate in the fairly low density region, and that the excess AuNPs even in the range of submonolayer resulted in the decrement of photocurrents.     

ORIENTATION OF SHORT WAVELENGTH AND LONG WAVELENGTH PROTOCHLOROPHYLL SPECIES IN GREENING CHLOROPLASTS

Abstract— The orientation of protochlorophyll and Chi species with respect to the plane of thylakoid membranes was studied by measuring the fluorescence polarization ratio in magnetically oriented chloroplasts isolated from greening maize leaves and cucumber cotyledons. With viewing direction parallel to the plane of the photosynthetic membranes, in the spectral region of 620–660 nm, fluorescence polarization ratios of 1.0 were observed, whereas at longer wavelengths the fluorescence polarization ratios were much higher, and similar to that of fully green chloroplasts. The same result was obtained with chloroplasts isolated from leaves fed by δ-amino levulinic acid. These data indicate that the emitting oscillators of the short and long wavelength protochlorophyll species are oriented at random with respect to the plane of thylakoid membranes. Isotropy of the protochlorophyll species is discussed in terms of isotropic structures containing Chi precursors.     

Phenazines as model low-midpoint potential electron shuttles for photosynthetic bioelectrochemical systems

Bioelectrochemical approaches for energy conversion rely on efficient wiring of natural electron transport chains to electrodes. However, state-of-the-art exogenous electron mediators give rise to significant energy losses and, in the case of living systems, long-term cytotoxicity. Here, we explored new selection criteria for exogenous electron mediation by examining phenazines as novel low-midpoint potential molecules for wiring the photosynthetic electron transport chain of the cyanobacterium Synechocystis sp. PCC 6803 to electrodes. We identified pyocyanin (PYO) as an effective cell-permeable phenazine that can harvest electrons from highly reducing points of photosynthesis. PYO-mediated photocurrents were observed to be 4-fold higher than mediator-free systems with an energetic gain of 200 mV compared to the common high-midpoint potential mediator 2,6-dichloro-1,4-benzoquinone (DCBQ). The low-midpoint potential of PYO led to O₂ reduction side-reactions, which competed significantly against photocurrent generation; the tuning of mediator concentration was important for outcompeting the side-reactions whilst avoiding acute cytotoxicity. DCBQ-mediated photocurrents were generally much higher but also decayed rapidly and were non-recoverable with fresh mediator addition. This suggests that the cells can acquire DCBQ-resistance over time. In contrast, PYO gave rise to steadier current enhancement despite the co-generation of undesirable reactive oxygen species, and PYO-exposed cells did not develop acquired resistance. Moreover, we demonstrated that the cyanobacteria can be genetically engineered to produce PYO endogenously to improve long-term prospects. Overall, this study established that energetic gains can be achieved via the use of low-potential phenazines in photosynthetic bioelectrochemical systems, and quantifies the factors and trade-offs that determine efficacious mediation in living bioelectrochemical systems.

Phenazines were explored as novel low-midpoint potential molecules for wiring cyanobacteria to electrodes.     

Laser-induced temperature jump electrochemistry on gold nanoparticle-coated electrodes

Laser-induced temperature jumps (LITJs) at gold nanoparticle-coated indium tin oxide (ITO) electrodes in contact with electrolyte solutions have been measured using temperature-sensitive redox probes and an infrared charge-coupled device. Upon irradiation with 532 nm light, interfacial temperature changes of ca. 20 degrees C were recorded for particle coverages of ca. 1 x 1010 cm-2. In the presence of a redox molecule, LITJ yields open-circuit photovoltages and photocurrents that are proportional to the number of particles on the surface. When ssDNA was used to chemisorb nanoparticles to the ITO surface, solution concentrations as low as 100 fM of target ssDNA-modified nanoparticles could be detected at the electrode surface.     

Studies on the interfacial charge transfer processes of nanocrystalline CdSe thin film electrodes by intensity modulated photocurrent spectroscopy

Interfacial charge transfer kinetics of the nanocrystalline CdSe thin film electrodes have been studied in sodium polysulfide solutions by intensity modulated photocurrent spectroscopy (IMPS). The interfacial direct and indirect charge transfer and recombination processes were analyzed in terms of the parameters: normalized steady state photocurrents and surface state lifetimes obtained by measuring the IMPS responses under different applied potentials and different solution concentrations. IMPS responses of polycrystalline CdSe thin film electrodes were also presented for comparison.     

强度调制光电流谱研究纳晶薄膜电极过程

用强度调制光电流谱研究半导体纳晶薄膜电极光生电荷的界面转移和输运动力学过程.从测量不同外加电压和不同硫化钠溶液浓度下CdSe纳晶薄膜电极的光电流响应得到了参数:归一化稳态光电流和表面态寿命,分析界面空穴的直接转移和通过表面态的间接转移过程.通过测量不同背景光强下TiO2纳晶薄膜电极的电子扩散系数研究电子输运过程.应用HCl化学处理方法明显增大了电子扩散系数,改善了电子在TiO2纳晶薄膜电极中的输运性能.     

Small-angle Hv light scattering from deformed spherulites with orientational fluctuation of optical axes

Mathematical evaluation was done for small-angle light scattering from disordered spherulites under Hv polarization conditions. The calculation was carried out for a two-dimensional deformed spherulite whose major optical axes are oriented at 0 or 45° with respect to the radial direction. The calculated results were compared with the scattering patterns observed for polypropylene (PP) spherulites, whose optical axes are oriented parallel to the radial direction, and poly(butylene terephthalate) (PBT) spherulites, whose optical axes are oriented at 45° with respect to the radial direction. The degree of disorder for PBT was much larger than that for PP. By selecting a parameter associated with the degree of disorder of the optical axes with respect to the radial direction, the patterns calculated as a function of draw ratios were in good agreement with the observed patterns, which changed from four leaves to streaks extended in the horizontal direction. Through a series of observed and calculated patterns, it turns out that an increase in the disorder under the deformation process occurs drastically even for perfect spherulites in an undeformed state.     

The Use of Light in the Study of Interfacial Electrochemical Reactions

Spectroscopic analysis techniques have become particularly important in the study of interfacial electrochemical processes since it has become possible to increase their sensitivity to the extent where changes occurring in the absorption of light by fractions of monolayers can be detected. At the same time the development of new techniques in surface physics, though most of these can only be used in ultra-high vacuum, has also had a considerable influence on electrochemistry since it has enabled studies to be carried out on electrodes after transfer to UHV. The availability of well-defined semiconductors in which photocurrents can be generated by the absorption of light has led to the development of photoelectrochemical methods that can be used for the study of electrode reactions at semiconductors or at metal surfaces which are covered with a semiconducting film. Finally, it has been observed during the study of semiconductor electrodes that redox reactions at an electrode can result in the generation of luminescence. This, in turn, can lead to important information on the mechanism of the charge transfer process. These recent developments are reviewed in the present article.     

含不同链长的三个卟啉LB膜修饰电极的光电响应研究

利用LB (Langmuir-Blodgett)技术将含不同链长的卟啉化合物(C4Py, C6Py和C8Py)单层膜转移到ITO (indium-tin oxide)导电玻璃上, 发现其具有良好的光电转换性质. 卟啉化合物修饰后的紫外吸收光谱与光电流工作谱重叠, 表明卟啉化合物起到了敏化光电流产生的效果; 而且电子给体、电子受体和偏压对其敏化效果的实验结果表明: 光诱导电子转移是产生光电响应的主要原因. 而且, 这三个卟啉化合物的光电响应性质与碳链长度相关, 其中含有六个碳链的C6Py表现出最佳的光电转化效果.     

A photoelectronic switching device using a mixed self-assembled monolayer

A cathodic-anodic biway photoelectronic device has been successfully constructed using a self-assembled monolayer (SAM). The SAM consists of two kinds of photofunctional thiol derivatives, a ruthenium complex-viologen linked compound (RuVS) and a phthalocyanine derivative (PcS), on a gold electrode. Structural characterization of the SAM has been carried out by absorption spectroscopy, cyclic voltammetry, and differential pulse voltammetry. Photocurrent responses were measured in the presence of methyl viologen (MV2+) and oxygen as electron acceptors and triethanolamine (TEOA) as a sacrificial reagent. For the SAM of RuVS alone, intramolecular electron transfer (ET) was superior to intermolecular ET, resulting in anodic photocurrents even in the presence of MV2+ and oxygen at 0 V vs Ag/AgCl. On the contrary, only cathodic photocurrents were observed at 0 V for the SAM of PcS alone. Photocurrents from the mixed SAM of RuVS and PcS were roughly the sum of individual photocurrents from RuVS and PcS. In fact, photocurrents from the mixed SAM of RuVS and PcS were observed in the anodic direction below approximately 550 nm, and in the cathodic direction above approximately 550 nm at 0 V vs Ag/AgCl. In the case of the mixed SAM of RuS (ruthenium complex disulfide) and PcS, only cathodic photocurrents were observed at 0 V vs Ag/AgCl, due to the lack of an intramolecular ET pathway. The results indicate that in the mixed SAM of RuVS and PcS both dyes can individually function for opposite photocurrent generation. We have also applied the mixed SAM as a photoelectronic logic device by using two LEDs (470 and 640 nm). The system clearly operated as an XOR logic device.     

Uniformly Oriented Zeolite ZSM‐5 Membranes with Tunable Wettability on a Porous Ceramic

Facile fabrication of well‐intergrown, oriented zeolite membranes with tunable chemical properties on commercially proven substrates is crucial to broadening their applications for separation and catalysis. Rationally determined electrostatic adsorption can enable the direct attachment of a b‐oriented silicalite‐1 monolayer on a commercial porous ceramic substrate. Homoepitaxially oriented, well‐intergrown zeolite ZSM‐5 membranes with a tunable composition of Si/Al=25–∞ were obtained by secondary growth of the monolayer. Intercrystallite defects can be eliminated by using Na⁺ as the mineralizer to promote lateral crystal growth and suppress surface nucleation in the direction of the straight channels, as evidenced by atomic force microscopy measurements. Water permeation testing shows tunable wettability from hydrophobic to highly hydrophilic, giving the potential for a wide range of applications.     

Semiconductor quantum dots for bioanalysis

Semiconductor nanoparticles, or quantum dots (QDs), have unique photophysical properties, such as size-controlled fluorescence, have high fluorescence quantum yields, and stability against photobleaching. These properties enable the use of QDs as optical labels for the multiplexed analysis of immunocomplexes or DNA hybridization processes. Semiconductor QDs are also used to probe biocatalytic transformations. The time-dependent replication or telomerization of nucleic acids, the oxidation of phenol derivatives by tyrosinase, or the hydrolytic cleavage of peptides by proteases are probed by using fluorescence resonance energy transfer or photoinduced electron transfer. The photoexcitation of QD-biomolecule hybrids associated with electrodes enables the photoelectrochemical transduction of biorecognition events or biocatalytic transformations. Examples are the generation of photocurrents by duplex DNA assemblies bridging CdS NPs to electrodes, and by the formation of photocurrents as a result of biocatalyzed transformations. Semiconductor nanoparticles are also used as labels for the electrochemical detection of DNA or proteins: Semiconductor NPs functionalized with nucleic acids or proteins bind to biorecognition complexes, and the subsequent dissolution of the NPs allows the voltammetric detection of the related ions, and the tracing of the recognition events.