空气包层大模场面积掺镱光子晶体光纤研究

采用改进的化学气相沉积法和气相液相混合掺杂技术制备大芯径掺镱石英光纤预制棒, 以此作为有源纤芯制备了纤芯直径约90 μm的掺镱双包层光子晶体光纤, 纤芯组分为镱铝磷共掺.双包层光子晶体光纤的模场面积约1330 μm², 纤芯数值孔径0.065,包层数值孔径0.5.首次实现了国产掺镱光子晶体光纤的高功率高效率激光输出, 1 m长的光子晶体光纤激光器实现102 W 激光输出,斜率效率76%.     

双包层光子晶体光纤激光器散热能力的理论研究

通过比较在相同发热功率和散热条件下双包层光子晶体光纤和传统双包层光纤的温度分布,考察了双包层光子晶体光纤的散热能力.数值研究结果表明：双包层光子晶体光纤的散热能力要弱于后者;但从总体来看,传统双包层光纤和光子晶体光纤的热性能对激光器的激光性能的影响是近乎相同的.     

高功率光子晶体光纤激光器温度分布研究

对高功率光子晶体光纤激光器温度分布问题进行了理论研究.在分析光纤热产生机理和结构的基础上,建立了双包层光子晶体光纤激光器稳态切面温度分布简单模型,数值模拟了光纤径向的温度分布、纤芯温度和纤芯-表面温差与纤芯热负载的关系,研究了光纤结构对温度分布的影响;并就激光器光纤泵浦端面的冷却方案进行讨论,数值模拟了外界对流系数不同时纤芯温度的大小.结果表明：对高功率光子晶体光纤激光器采用风冷和水冷的方法可以降低热效应的影响.     

两光子晶体光纤激光器相干锁定的实验研究

利用自成像腔技术进行光子晶体光纤(PCF)激光器光束相干合成的实验研究,实现了两光子晶体光纤激光器的相位锁定.在不使用滤波器的情况下,实验仍能观测到清晰的下涉图样,且在高功率输出状态以及环境噪声情况下干涉图样仍可保持稳定,表明具有单模大模场特性的光子晶体光纤在实现光束相干合成方面比传统的双包层光纤(DCF)有明显的优越性.实验还表明耦合输出镜的反射率对相干输出功率有一定影响,当反射镜的反射率分别为5%,10%和15%时,两台激光器相干输出斜率效率分别为63.8%,61.6%和60.2%.在抽运功率为150 W和耦合输出镜的反射率为5%时,获得95.8 W的最大相干功率输出,相干功率合成效率为90.2%.实验中无任何热光效应产生,有望利用该方法获得更高的相干输出功率.     

应用耦合模理论研究光在圆对称双包层光纤中的传输

为了深入理解双包层光纤的光场传输特性,应用耦合模理论将双包层光纤等效为相互耦合的单模光纤和环形芯光纤,研究了圆对称的双包层光纤的光场传输.通过计算单模光纤LP01模和环形芯光纤导模的耦合系数发现了环形芯光纤LP0n模的耦合系数远大于其它导模的耦合系数,且LP0n模中的高阶模比低阶模的耦合系数大.据此,应用耦合模理论计算得到了该双包层光纤的光传输特性,计算结果发现光场沿光纤轴向呈近似周期分布,且纤芯中光功率变化的平均周期随波长递增,但平均归一化功率与光纤参数紧的选择有关.     

应用耦合模理论研究光在圆对称双包层光纤中的传输(英文)

为了深入理解双包层光纤的光场传输特性,应用耦合模理论将双包层光纤等效为相互耦合的单模光纤和环形芯光纤,研究了圆对称的双包层光纤的光场传输.通过计算单模光纤LP01模和环形芯光纤导模的耦合系数发现了环形芯光纤LP0n模的耦合系数远大于其它导模的耦合系数,且LP0n模中的高阶模比低阶模的耦合系数大.据此,应用耦合模理论计算得到了该双包层光纤的光传输特性,计算结果发现光场沿光纤轴向呈近似周期分布,且纤芯中光功率变化的平均周期随波长递增,但平均归一化功率与光纤参数紧的选择有关.     

七芯光子晶体光纤结构优化的数值分析

从耦合模方程出发,推导了描述七芯光子晶体光纤模场特性的本征方程,得到了这种结构光纤的本征值和本征矢.使用频域有限差分法数值模拟,通过改变传输波长、纤芯间距、包层孔大小分析了纤芯之间的强度分布与耦合系数的关系,分别实现了模式整形和高阶超模截止.掌握了具有强耦合特性的七芯光子晶体光纤设计规律,和这种结构光子晶体光纤的同相位超模的选取方法. 关键词： 光子晶体光纤 大模场面积光纤 多芯结构 频域有限差分法     

大模面积掺Yb~(3+)七芯光子晶体光纤的设计

要提高七芯光子晶体光纤激光器的输出功率,必须要增大七芯光子晶体光纤的有效模面积,并且需要纤芯间具有较强的耦合作用,以保证各纤芯输出的光束保持同相位。为了更直观的分析七芯光子晶体光纤的有效模场面积和纤芯间耦合强度的关系,根据七芯光子晶体光纤7个超模的特征,给出了七芯光子晶体光纤耦合长度的一种计算方法。利用多极法和有限差分光束传播法分析了七芯光子晶体光纤的结构对有效模场面积和耦合长度的影响。通过优化七芯光子晶体光纤的结构,设计了一种外层空气孔较大,内层空气孔较小的七芯光子晶体光纤,其有效模场面积高达3703μm2,耦合长度仅为13310μm。     

一种阶梯结构的色散平坦光子晶体光纤的研究

以多极法理论为基础,提出了一种阶梯结构的光子晶体光纤.通过改变其内四层的三个结构参量(内两层孔孔径,外两层孔孔径和孔间距),实现色散绝对值在1.1～1.8μm的波段内变化仅为0.05～2 ps/(km·nm)的平坦甚至超平坦的特性.在此情况下对其有效模场面积进行数值模拟,充分展示了达到色散平坦和超平坦时,相对于传统光子晶体光纤,此种结构的光纤对芯区内光场的局域能力有很大程度的增强,其有效模场面积可仅为传统光子晶体光纤的1/30.最后,经过大量的数值计算和理论分析,归纳出若要此种阶梯结构的光纤在1.1～1.8μm的波段内达到色散平坦甚至超平坦特性的设计依据.     

掺Yb3+双包层大模面积光子晶体光纤激光器的研究

采用多模大功率半导体激光器泵浦掺镱双包层大模面积光子晶体光纤,应用5 m长光子晶体光纤,在泵浦功率为22 W的条件下,获得了1.03 μm,功率为65 mW的单横模激光输出,同时实验研究了输出功率与泵浦功率的关系,并观察到掺Yb3+光子晶体光纤侧面有绿色荧光出现.     

光子晶体光纤包层可见光及红外宽带色散波产生

对光子晶体光纤包层3个空气孔之间节区的传光特性进行了分析, 对比了纤芯与包层节区传光的模场面积、非线性系数及色散特性, 得到光子晶体光纤包层节区具有小芯、高非线性的特点.在包层空气孔较大的情况下, 得到了双零色散曲线.根据色散曲线, 分析了色散波产生的相位匹配特性, 得到了色散波中心波长随抽运波长及功率的变化规律.制备出了所设计的光子晶体光纤, 实验得到了在可见光及红外大于300 nm的宽带色散波, 并给出了色散波随抽运波长及功率的变化规律.实验和理论分析结果一致, 为波长变换及超连续宽带光源的研究奠定了基础. 关键词： 光子晶体光纤 色散波 相位匹配 非线性     

多芯光子晶体光纤高功率超连续谱光源

分析基于单芯光子晶体光纤的超连续谱光源在提升平均输出功率时所面临的问题,指出采用多芯光子晶体光纤作为超连续谱产生介质是一种实现高功率超连续谱产生的潜在方案。使用自制皮秒光纤激光器泵浦一段国产多芯光子晶体光纤,实现了光谱范围750~1700 nm,平均功率42.3 W的全光纤化高功率超连续谱输出。     

空芯带隙型光子晶体光纤整体空气孔包层导光特性研究

 传统光纤包层中仅存在泄漏的倏逝波,能量较小,不利于包层传感的应用。增大包层中的能量,实现整体包层导光是提高光纤传感灵敏度的有效途径。从理论上分析了利用空芯带隙型光子晶体光纤(HC-PCF)包层进行导光的机理。在实验上选用带隙外的冷光源和激光对一种典型结构的HC-PCF进行了空气孔包层的导光实验,并利用折射率引导型光子晶体光纤和单模光纤进行对比实验。结果表明,带隙范围外光波在HC-PCF中传输时将不受禁带效应的约束泄露至包层中重新分布。包层中SiO2与空气孔的周期型结构将光波约束在高折射率介质中,实现HC-PCF整体空气孔包层中光波的稳定传输。PBG-PCF包层的整体导光在传感上有提高灵敏度的潜在价值。     

Study of heat transfer characteristics in PCFG fabrication technology using heat method

The fiber gratings fabrication technology with the heating method in a photonic crystal fiber (PCF) based on structural change is examined. The principle of photonic crystal fiber gratings (PCFGs) is analyzed in theory. The heat transfer theory and finite element method are used to examine the thermal field distribution in the fiber and the influence of the air hole structure in the cladding, and the parameters of the laser beam in the process of grating fabrication are discussed. The results show that gratings can be formed by the periodic collapse of air holes in the cladding of PCFs. Under double-point heating condition, the energy is uniformly distributed in the radial direction and is approximate to Gaussian distribution in the axial direction. With the same size of the luminous spot, as the layers and radius of the air holes increase, the laser power needed to make the air holes collapse decreases. With the same laser power, as the luminous spot radius increases, the needed heating time increases. Moreover, the relationship between the laser power needed and the air filling rate is obtained as the number of layers of the air holes changes from 1 to 7. This kind of PCFG can overcome the long-term thermal instability of conventional gratings in substance and thus has great potential applications in the related field of optical fiber sensors.     

热激法光子晶体光纤光栅制备工艺中热传导特性研究

研究了基于结构性改变的光子晶体光纤光栅的热激法制备工艺,理论分析了此种工艺的成栅原理,采用热传导理论和有限元法研究了制备过程中光子晶体光纤中的温度场分布,以及包层空气孔结构和激光参数对成栅效果的影响.研究结果表明,利用光子晶体光纤包层空气孔周期性塌缩可以形成光栅;采用两点热激法时,能够实现能量在光纤径向均匀分布,轴向近似于高斯分布;包层气孔结构加速了成栅过程,相同光斑尺寸下,光纤塌缩所需激光功率随气孔层数和气孔半径的增大而减小;最后,对包层空气孔结构为1层到7层的光子晶体光纤热激过程进行仿真,得到了空气填 关键词： 光纤光栅 光子晶体光纤 热激法 有限元法     

光子晶体光纤布拉格光栅传输谱特性的分析

研究光子晶体光纤中光纤光栅的传输谱特性对于研制基于光子晶体光纤的光纤光栅器件有着重要的意义。结合耦合模理论和光束传输相关函数方法,对一种典型光子晶体光纤中的布拉格光栅(FBG)传输谱进行了理论分析。比较了光子晶体光纤中布拉格光栅与常规布拉格光栅的传输谱。数值分析了光纤截面结构变化对于光栅传输谱的影响,并给出这种影响的定性解释。计算结果显示,与常规光纤光栅相比,包层模共振引起的损耗峰与正反向纤芯模耦合引起的损耗峰可以相比拟,而包层模共振的间隔也比常规光纤中光纤光栅的包层模共振间隔要大。同时给出了晶体光纤截面上空气孔的占空比,空气孔的排布层数对于传输谱影响的规律。     

A colloidal crystal microstructure fiber: fabrication and characterization

A method of fabricating colloidal crystal microstructured fiber is presented. The proposed structure relies on partial etching of the cladding layer of a single-mode fiber and growth of colloidal photonic crystals inside eroded area. The photonic crystal cylindrical annulus embedded in fiber is characterized by optical and scanning electron microscopy. The optical characterization was analyzed by optical transmission spectroscopy. The measurement results show a about 1550-nm band gap. The results also reveal the possibility of cladding cylindrical fibers with three-dimensional photonic crystals.     

Silica-air photonic crystal fiber design that permits waveguiding by a true photonic bandgap effect

A theoretical investigation of a novel type of optical fiber is presented. The operation of the fiber relies entirely on wave guidance through the photonic bandgap effect and not on total internal reflection, thereby distinguishing that fiber from all other known fibers, including recently studied photonic crystal fibers. The novel fiber has a central low-index core region and a cladding consisting of a silica background material with air holes situated within a honeycomb lattice structure. We show the existence of photonic bandgaps for the silica-air cladding structure and demonstrate how light can be guided at the central low-index core region for a well-defined frequency that falls inside the photonic bandgap region of the cladding structure.     

Design of double cladding dispersion flattened photonic crystal fiber with deformation insensitive outer cladding air-holes

A design of double cladding dispersion flattened photonic crystal fiber (DF-PCF) is proposed. To employ traditional stack and draw technology, the cladding of the DF-PCF is consisted of triangular periodic air-holes with the same hole to hole pitch. Simulation results show that the small air-holes in the inner cladding are mainly for dispersion management. The large air-holes in the outer cladding are mainly used for light confinement and have little impact on the dispersion tailoring. Thus, the dispersion profile of the double cladding DF-PCFs is insensitive to the deformation of air-holes in the outer cladding. Considering that the larger air-holes are apt to deform in the drawing procedure, the characteristics mentioned above make the realization of DF-PCFs relative easy by employing conventional stack and draw technology and modest air-hole rings (less than 10 rings) in the cladding.     

Band structure of photonic crystal fibers with silica rings in triangular lattice

The characteristics of the cladding band structure of air-core photonic crystal fibers with silica rings in triangular lattice are investigated by using a standard plane wave method. The numerical results show that light can be localized in the air core by the photonic band gaps of the fiber. By increasing the air-filling fraction, the band gap edges of the low frequency photonic band gaps shift to shorter wavelength, whereas the band gap width decreases linearly. In order to make a specified light fall in the low frequency band gaps of the fiber, the interplay of the silica ring spacing and the air-filling fraction is also analyzed. It shows that the silica ring spacing increases monotonously when the air-filling fraction is increased, and the spacing range increases exponentially. This type fiber might have potential in infrared light transmission.