XPS studies of octadecylphosphonic acid (OPA) monolayer interactions with some metal and mineral surfaces

Partial and complete self‐assembled monolayers (SAMs) of octadecylphosphonic acid (OPA) have been deposited onto air‐exposed surfaces of the metals copper, silver, gold, iron, silicon and aluminium, as well as onto freshly cleaved, air‐exposed surfaces of the minerals muscovite and biotite. The line width of the C(1s) signal in the XPS spectra of the surface narrowed, as the extent of coverage increased to 100%, to a half‐width of 0.9 eV. Moreover, the line widths associated with the insulating muscovite substrate also became substantially narrower as OPA coverage increased. Binding energy differences on this charge‐shifted surface were found to be more consistent when OPA was used as a charge reference, compared to using adventitious carbon as a reference. OPA coverage of the air‐exposed metals copper, silver, gold and iron also produced narrow C(1s) spectra whose binding energies were consistently close to 284.9 eV. The C(1s) binding energy positions on Al and Si samples were charge‐shifted by the insulating nature of the thin oxide formed on air exposure, or by the insulating nature of the substrate in the case of the minerals. Correction of the observed C(1s) energy position to 284.9 eV gave sets of elemental binding energies for the substrate materials that were reproducible. Thus, OPA coverage could be a possible alternative candidate for use in charge correction of binding energies of insulating materials. The OPA coverage cases were modelled using the software QUASES^? Analyse. For the substrates copper, silver, gold, iron and aluminium, analyses of the metal core line spectra gave OPA overlayer thicknesses close to those measured by AFM (1.6 nm). However, QUASES^? analyses of the C(1s) extrinsic backgrounds for the same surfaces required the use of an attenuation length of only 0.4 nm to derive a comparable thickness—much lower than literature values for carbon. This discrepancy is ascribed to the structured nature of the SAM. Copyright © 2005 John Wiley & Sons, Ltd.     

Interaction of Cyanoacrylate with Metal Oxide Surfaces (Cu,Al)

Cyanoacrylates are an extremely reactive class of adhesives. Despite their commercial use as instant adhesives, the adhesion mechanism, especially to technically relevant oxidized metal surfaces, has not yet been sufficiently investigated. In the present work, ultra-thin ethyl cyanoacrylate films are deposited on copper oxide and aluminum oxide by spin coating and cured there. Various surface sensitive spectroscopy methods are used to identify possible interactions. X-Ray photoelectron spectroscopy (XPS) indicates, among other information, hydrogen bonding of the carbonyl group to the oxidized surfaces. Metastable induced electron spectroscopy (MIES) measurements support the theory of this preferential molecular orientation. In addition, XPS shows the presence of an ionic carboxylate (COO⁻) species at the interface. Infrared reflection adsorption spectroscopy (IRRAS) measurements confirm this ionic interaction and furthermore allow to investigate the influence of water on the reaction. A possible interaction mechanism of cyanoacrylates with metal oxides could be proposed. The formation of a carboxylate species probably occurs by hydrolysis of the ethyl group via the intermediate of a carboxyl (COOH) species.     

Specimen transfer from the electrolyte to the UHV in a closed system and some examinations of the double layer on Cu

A transfer system is described which permits the electrochemical preparation of specimens in a purified argon atmosphere and their transport into the UHV for surface analysis. This transfer prevents contamination and oxide formation on semi-noble metals. Reactive metals from only a few monolayers of oxide. This permits examination of electrochemically prepared metal surfaces, which is otherwise not possible. For hydrophobic copper surfaces, the composition of the electrical double layer may be studied. The extraction of the electrode strips the electrolyte off in the vicinity of the Helmholtz layer. For NaClO₄ solutions, the amount of Na⁺ ions and the excess charge decrease linearly with the electrode potential in agreement with a constant electrode capacity. The formation of a prepassive and passive layer leads to a pronounced increase of adsorbed Na⁺ ions. For Cs₂SO₄, specific and co-adsorption of both ions is observed with a minimum in the region of the potential of zero charge.     

Chemical and structural changes at the ABS polymer-copper metal interface

Creating oxygen containing moieties (hydroxyl or carbonyl) on polymer substrate surfaces is known to increase the adhesion strength of polymers to metals. However, we noticed adhesion increase with time even though no pre- or post-treatment of the polymer substrate was done. In the case of sputtered and galvanically strengthened copper coatings on acrylonitrile-butadiene-styrene polymer (ABS) substrate, the adhesion strength increased from approximately 6 J/m² to 53 J/m² during a 1008-h period. During this period structural and chemical changes of the polymer near the interface take place. Carbonyl functionalities developed on the ABS surface are most likely responsible for the large increase in the adhesion strength. Chemical changes of the polymer are probably a consequence of the galvanic deposition and a close contact of ABS with copper which is known to facilitate the oxidation of ABS.     

A Dendritic Nanostructured Copper Oxide Electrocatalyst for the Oxygen Evolution Reaction

To use water as the source of electrons for proton or CO₂ reduction within electrocatalytic devices, catalysts are required for facilitating the proton‐coupled multi‐electron oxygen evolution reaction (OER, 2 H₂O→O₂+4 H⁺+4 e⁻). These catalysts, ideally based on cheap and earth abundant metals, have to display high activity at low overpotential and good stability and selectivity. While numerous examples of Co, Mn, and Ni catalysts were recently reported for water oxidation, only few examples were reported using copper, despite promising efficiencies. A rationally designed nanostructured copper/copper oxide electrocatalyst for OER is presented. This material derives from conductive copper foam passivated by a copper oxide layer and further nanostructured by electrodeposition of CuO nanoparticles. The generated electrodes are highly efficient for catalyzing selective water oxidation to dioxygen with an overpotential of 290 mV at 10 mA cm⁻² in 1 m NaOH solution.     

Surface properties of the Ni-Cu-Cr oxide catalyst for dehydrogenative hydrolysis of amines

Catalysts for dehydrogenative hydrolysis of amines, prepared by sorption of copper ions from a solution on a preformed Ni-Cr oxide system, were studied by Auger electron spectroscopy, X-ray photoelectron spectroscopy, and IR spectroscopy of adsorbed CO and NH₃ probe molecules. It was shown that on adsorption copper blocked the chromium ions in the Ni-Cr catalyst with concomitant stabilization as Cu⁺. The incorporation of copper into the Ni-Cr system increased the ability of nickel to reduce water with the formation of oxygen-containing complexes.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 288–291, February, 1993.     

An in situ SERS and FTIRAS study of salicylate interaction with copper electrode

The salicylate anion (ortho-hydroxy-benzoate-C₆H₄OHCOO⁻) interacts with common metals forming a semi-passivating layer on the surface. This semi-passivating layer allows the application of relatively high positive potentials without significant dissolution of the metal. It enables the electro-synthesis of conducting polymers (e.g. polyaniline, polypyrrole) directly on the metal surface, and such polymeric layers can act as anti-corrosion materials. Notwithstanding this characteristic, the behavior of salicylate on different metal surfaces is not yet well-understood. In the present work, the interaction of salicylate with copper (a metal of great interest in the industry) was studied. For this purpose, in situ surface enhanced raman scattering (SERS) and Fourier transform infrared absorption spectroscopy (FTIRAS) experiments were performed. The results show the formation of a copper(II) salicylate complex in the solution since low potentials (ca. 0 V vs Ag/AgCl). At higher potentials, salicylate decomposition is observed. FTIR spectra show the formation of CO₂ in solution, indicating salicylate decarboxilation. The SERS experiments indicate the breakage of the benzenic ring on the surface. It is suggested that at potentials above 0.6 V, a film of insaturated aliphatic chains linked by oxygen atoms is formed on the surface. This paper is dedicated in memoriam to Prof. Francisco Carlos Nart.     

Zerovalent metal polymer composites. III. Metallization of metal oxide surfaces with the aid of metallized functional polymer microdispersions

The adsorption of poly[N-(m- and p-vinylbenzyl)-N,N,N-trimethylammonium tetrachloropal-ladate] complex on inorganic oxide surfaces followed by reduction of the palladium salt to form a catalytically active zerovalent metal polymer composite dispersed on the oxide surface and further deposition of transition metals, e.g., nickel, cobalt, and copper, by “additive” or “subtractive” deposition from electroless plating solutions is described. γ-Ferric oxide was used as a template for such intermetallic replacement reactions, providing materials with controlled amounts of metal. Multimetallic catalysts based on aluminum oxide, zinc oxide, lanthanum oxide, magnesium oxide, and silica were prepared. Iron oxide modified by subtractive deposition of rhodium and iridium on nickel-clad iron oxide were evaluated in Fischer–Tropsch carbonylation reactions leading from synthesis gas to alkanols.     

Preparing graphene oxide–copper composite material from spent lithium ion batteries and catalytic performance analysis

The wide use of lithium ion batteries (LIBs) has created much waste, which has become a global issue. It is vital to recycle waste LIBs considering their environmental risks and resource characteristics. Anode graphite from spent LIBs still possess a complete layer structure and contain some oxygen-containing groups between layers, which can be reused to prepare high value-added products. Given the intrinsic defect structure of anode graphite, copper foils in LIB anode electrodes, and excellent properties of graphene, graphene oxide–copper composite material was prepared in this work. Anode graphite was firstly purified to remove organic impurities by calcination and remove lithium. Purified graphite was used to prepare graphene oxide–copper composite material after oxidation to graphite oxide, ultrasonic exfoliation to graphene oxide (GO), and Cu²⁺ adsorption. Compared with natural graphite, preparing graphite oxide using anode graphite consumed 40% less concentrated H₂SO₄ and 28.6% less KMnO₄. Cu²⁺ was well adsorbed by 1.0 mg L^?1 stable GO suspension at pH 5.3 for 120 min. Graphene oxide–copper composite material could be successfully obtained after 6 h absorption, 3 h bonding between GO and Cu²⁺ with 3/100 of GO/CuSO₄ mass ratio. Compared to CuO, graphene oxide–copper composite material had better catalytic photodegradation performance on methylene blue, and the electric field further improved the photodegradation efficiency of the composite material.     

Oxidation behaviors of metallic copper particles in NO reduction mechanism of copper/activated carbons

The reduction of nitric oxide (NO) over Cu/ACFs, prepared by copper electroplating, has been studied. It is found that copper content on the ACFs increases with increasing plating time (up to 45 wt%), while the textural properties including specific surface areas and total pore volumes decrease. As an experimental result, the NO reduction efficiency is increased in all of the Cu/ACFs, and it is confirmed that NO is converted into nitrogen and oxygen on the Cu/ACF surfaces (at 500 degrees C). Especially, the Cu metals on the ACF surfaces scavenge oxygen by oxidizing themselves into Cu2O and finally CuO as a reductant. It is indicated that copper metals on the Cu/ACFs play a major role in the NO removal in this system.     

A method to investigate the interaction of rare earth elements in aqueous solution with metal oxides

A method is described which can be used to investigate the interaction of dissolved metals with particulate material. Low level concentrations (10^–9M) of rare earth radiotracers were used to investigate their sorption onto synthetic mineral oxide surfaces. The preparation of rare earth radiotracers by neutron activation is discussed in detail. A kinetic approach was employed to investigate the interaction of dissolved metals and suspended mineral oxides. Amorphous iron oxyhyroxide, a phase commonly found in nature, was used in sorption experiments carried out in seawater at pH 7.8 and 2°C. Results of this study indicate a high affinity of the rare earth elements (REE) for the iron oxide surface (evidenced by fast uptake and high partition coefficients) and reveal a fraction between light and heavy REE.     

Minimization of Cu and Ni interferences in the determination of Sb by hydride generation atomic absorption spectrometry: the use of picolinic acid as masking agent and the influence of l-cysteine

The minimization of copper and nickel interference on the determination of antimony by hydride generation atomic absorption spectrometry using picolinic acid and l-cysteine as masking agents was studied. Concentrations up to 4000 and 1000 mg l⁻¹ of nickel and copper respectively were found to be tolerable in the presence of picolinic acid. The simultaneous presence of both transition metals could be tolerated by using a mixture of picolinic acid and l-cysteine. In the analysis of a nickel oxide certified reference material good agreement between the recommended and found values was verified. A detection limit (3 s, n=10) of 0.1 μg Sb g⁻¹ in the original sample was estimated.     

Low-Temperature H2 Reduction of Copper Oxide Subnanoparticles

Subnanoparticles (SNPs) with sizes of approximately 1 nm are attractive for enhancing the catalytic performance of transition metals and their oxides. Such SNPs are of particular interest as redox-active catalysts in selective oxidation reactions. However, the electronic states and oxophilicity of copper oxide SNPs are still a subject of debate in terms of their redox properties during oxidation reactions for hydrocarbons. In this work, in situ X-ray absorption fine structure (XAFS) measurements of Cu₂₈O_x SNPs, which were prepared by using a dendritic phenylazomethine template, during temperature-programmed reduction (TPR) with H₂ achieved lowering of the temperature (T₅₀=138 °C) reported thus far for the Cu^II→Cu^I reduction reaction because of Cu−O bond elongation in the ultrasmall copper oxide particles.     

Rollover‐Assisted C(sp2)C(sp3) Bond Formation

Rollover cyclometalation involves bidentate heterocyclic donors, unusually acting as cyclometalated ligands. The resulting products, possessing a free donor atom, react differently from the classical cyclometalated complexes. Taking advantage of a “rollover”/“retro‐rollover” reaction sequence, a succession of oxidative addition and reductive elimination in a series of platinum(II) complexes [Pt(N,C)(Me)(PR₃)] resulted in a rare C(sp²)?C(sp³) bond formation to give the bidentate nitrogen ligands 3‐methyl‐2,2′‐bipyridine, 3,6‐dimethyl‐2,2′‐bipyridine, and 3‐methyl‐2‐(2′‐pyridyl)‐quinoline, which were isolated and characterized. The nature of the phosphane PR₃ is essential to the outcome of the reaction. This route constitutes a new method for the activation and functionalization of C?H bond in the C(3) position of bidentate heterocyclic compounds, a position usually difficult to functionalize.     

Corrosion inhibition performance of 2-ethyl phenyl-2, 5-dithiohydrazodicarbonamide on Fe (110)/Cu (111) in acidic/alkaline solutions: Synthesis,experimental, theoretical,and molecular dynamic studies

Herein, 2-ethyl phenyl-2,5-dithiohydrazodicarbonamide (2EPDCA) was synthesised and tested as a corrosion inhibitor for mild steel (MS) and copper (Cu) in 1 M HCl and 3.5% NaCl, respectively. Fourier transform infrared spectroscopy (FT-IR) and (NMR) nuclear magnetic resonance (¹H, ¹³C) were used to identify the chemical structure. Both experimental and computational approaches have been conducted to evaluate inhibitor efficiency on both metal systems. The electrochemical results showed that the 2EPDCA inhibition efficiency for MS systems was 95% at 1 × 10^?2 M, while in copper systems it was 97.5% at 1 × 10^?2 M. The Langmuir adsorption isotherm was fitted using adsorption surface coverage data, and for inhibitor in both systems, the kind of adsorption was mixed (physisorption and chemisorption). Through scanning electron microscopy (SEM), EDX, and atomic force microscopy (AFM) tests, we have confirmed the presence of the inhibitor molecules on the metal surface in both systems. Quantum chemistry simulations indicate that the superior corrosion inhibition efficacy of 2EPDCA on copper compared to mild steel surfaces is attributable to the former's greater electron donating propensity on copper. The adsorption of 2EPDCA molecules on Fe (110) and Cu (111) surfaces was further verified by molecular dynamic simulations, with the former having a greater adsorption energy. The results indicate that the corrosion inhibitor was effective even in harsh conditions, and it can be thought of as a novel corrosion inhibitor for mild steel and copper that provides good protection.     

Synthesis,characterization and ionic conductivity of poly[(oligoethylene oxide) ethoxysilane] and poly[(oligoethylene oxide) ethoxysilane]/(EuCl3)0.67

Poly[(oligoethylene oxide) ethoxysilane)] ( I ) and poly[(oligoethylene oxide) ethoxysilane)]/(EuCl₃)_0.67 ( II ) were synthesized by reacting tetraethoxysilane with oligo(ethylene glycol) of molecular weight 400 and oligo(ethylene glycol)400/(EuCl₃)_0.317, respectively. The products so obtained are very transparent and rubbery. By Fourier transform infrared and Raman spectroscopy studies and by using analytical results it was concluded that these products are crosslinked macromolecular materials where the Si atom is bonded to one OEt group and to three poly(ethylene oxide) 400 chains. Scanning electronic microscopy studies showed that the presence of EuCl₃ in polymer host significantly affects the morphology of the material. Laser luminescence investigations on (II) showed that Eu³⁺ ion in the polymer host is accommodated in two different types of sites having a distorted C_2v symmetry. Moreover, the ionic conductivity of these systems was investigated and the data were satisfactorily fitted by the empirical Vogel Tamman Fulcher equation. At 70°C the conductivities of ( I ) and ( II ) were 9 × 10⁻⁶ and 14.3 × 10⁻⁶ Ω⁻¹ cm⁻¹ respectively.     

In situ investigations of the interaction of small inorganic acidifying molecules in humidified air with polycrystalline metal surfaces by means of TM‐AFM,IRRAS, and QCM

Initial atmospheric corrosion of copper, silver, and iron induced by humidity and oxidizing agents was studied in situ by three highly surface‐sensitive and complementary techniques: infrared reflection‐absorption spectroscopy (IRRAS), quartz crystal microbalance (QCM), and tapping‐mode atomic force microscopy (TM‐AFM). These techniques deliver information about the change of the topography of the sample surfaces with emphasis on the shape and lateral distribution of the corrosion products grown within the first 1300–2800 min of weathering (TM‐AFM), as well as chemical (IRRAS) and kinetic (QCM) data. A completely different mechanism of the initial stages of atmospheric corrosion of the three investigated metals could be observed. A uniform growth of corrosion products was seen on the copper surface (identified by IRRAS and XPS to be cuprite‐like) during exposure to synthetic air with 80% relative humidity (RH), whereas the iron surface remained unattacked. The investigations of the silver surface exposed to humidity revealed that silver is attacked by humidity and tends to form oxide and hydroxide surface species. While an increased humidity content of the surrounding atmosphere causes higher corrosion rates on copper, on the exposed silver sample only a change in the degradation mechanism could be observed. The addition of SO₂ to the humidified air causes the growth of so‐called ‘second‐order’ features on copper, identified to be CuSO₃ · xH₂O‐like, which reveals the formation of a new chemical species on the investigated surface. These features are placed on top of the homogeneous formed oxide layer and tend to form well‐defined islands. In contrast to copper, on a silver surface exposed to humidity and SO₂ no new chemical species are formed; nevertheless an increased corrosion rate could be observed owing to a change of the chemistry in the physisorbed water layer. Iron exposed to humidity and SO₂ still remains unattacked. An iron surface is attacked only if exposed to humidity and SO₂ and NO₂, which show a synergistic effect by the oxidation of four‐valent sulfur‐oxygen species by NO₂. Such an attack leads to the formation of pitting corrosion, which was observed in situ and time‐resolved. The pits mainly occur on predamaged surface structures, such as scratches caused from the polishing process of the samples, and therefore promote the initiation of the corrosion. The results obtained demonstrate the high potential of the surface‐sensitive methods applied for investigating the early stages of corrosion of different metals and for obtaining a better understanding of the molecular mechanisms during degradation. Copyright © 2007 John Wiley & Sons, Ltd.     

Reactions of a Polyhalide Ionic Liquid with Copper,Silver, and Gold

The reactions of copper, silver, and gold with the imidazolium-based polyhalide ionic liquid (IL) [C₆C₁Im][Br₂I] were investigated by using X-ray photoelectron spectroscopy (XPS), weight-loss measurements, and gas-phase mass spectrometry. All three Group 11 metals are strongly corroded by the IL at moderate temperatures to give a very high content of dissolved Cu^I, Ag^I, and Au^I species. The IL–metal solutions are stable against contact with water and air. The replacement of imidazolium with inorganic sodium cations decreased metal corrosion rates by orders of magnitude. Our results clearly indicate metal oxidation by iodide from dibromoiodide anions to form molecular iodine and anionic [Br-M^I-Br]⁻ (M=Cu, Ag, Au) complexes stabilized by imidazolium counterions. From experiments with a trihalide IL with imidazolium methylated at the 2-position, we ruled out the formation of imidazole–carbene as a cause of the observed corrosion. In contrast to Group 11 metals, molybdenum is inert against the trihalide IL, which is attributed to surface passivation.     

Hybrid graphene oxide/DAB-Am-16 dendrimer: Preparation,characterization chemical reactivity and their electrocatalytic detection of l-Dopamine

Graphene oxide (GO) was chemically modified with a poly(propylene)imine Generation 3.0 dendrimer (DAB-Am-16). The characterization, structure and properties of hybrid graphene oxide/DAB-Am-16 dendrimer was studied by Raman spectroscopy, Fourier-Transforming Infrared Spectroscopy (FT-IR), X-Ray Photoelectron Spectroscopic (XPS), X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM) and Thermogravimetric analysis. After functionalized the hybrid material (GOD) can interact with copper and subsequently with hexacyanoferrate (III) ions (GODHCu). The GODHCu incorporated into a graphite paste electrode (20% w/w) was applied to an electrocatalytic detection of neurotransmitter l-dopamine using differential pulse voltammetry. The analytical curve showed a linear response in the concentration range from 1.0 × 10⁻⁷ to 1.0 × 10⁻⁵ mol L⁻¹ with a corresponding equation Y(A) = 1.706 × 10⁻⁵ + 0.862 [l-dopamine] and a correlation coefficient r² = 0.998. The detection limit was 6.36 × 10⁻⁷ mol L⁻¹ with a relative standard deviation of ±4% (n = 3) and an amperometric sensitivity of 0.862 A/mol L⁻¹.     

An infrared study on the chemisorption of tertiary phosphines on coinage and platinum group metal surfaces

The chemisorption of dimethylphenyl-, methyldiphenyl- and triphenylphosphine on evaporated gold, silver, copper, rhodium, iridium, palladium, platinum and nickel surfaces has been studied by means of infrared reflection–absorption spectroscopy (IRAS). Multilayers of physisorbed phosphine are formed on the surfaces of all metals studied except nickel after deposition from dilute toluene solution. The deposition rate varies for different metal surfaces and it is sometimes quite slow. The standard immersion time was 20 h in this study to secure that an equilibrium between the surface and the solution is reached. Several minutes of ultrasonic treatment are required to get rid of the physisorbed phosphine, leaving a very thin layer of chemisorbed phosphine on the metal surface. Most of the absorption bands in IRAS spectra of these thin layers show significant shifts, which are especially large for dimethylphenylphosphine. It is evident that the electron distribution in the entire phosphine molecules is changed and that the chemisorption to the coinage and platinum group metal surfaces is strong. Infrared spectra of coordination compounds of gold(I), silver(I) and copper(I) with dimethylphenyl-, methyldiphenyl- and triphenylphosphine and of the corresponding phosphine oxides have served as reference material for the chemisorbed phosphines. The spectra of the coordination compounds show similar shifts and intensity changes as the IRAS spectra of tertiary phosphines chemisorbed on the coinage and platinum group metals. This suggests that the studied phosphines are as strongly bound to the coinage and platinum group metal surfaces as to the monovalent coinage metal ions known to form very stable complexes with tertiary phosphines.