Reduced surface adsorption in 3D printed acrylonitrile butadiene styrene micro free-flow electrophoresis devices

We have 3D printed and fabricated micro free-flow electrophoresis (µFFE) devices in acrylonitrile butadiene styrene (ABS) that exhibit minimal surface adsorption without requiring additional surface coatings or specialized buffer additives. 2D, nano LC–micro free flow electrophoresis (2D nLC × µFFE) separations were used to assess both spatial and temporal broadening as peaks eluted through the separation channel. Minimal broadening due to wall adsorption was observed in either the spatial or temporal dimensions during separations of rhodamine 110, rhodamine 123, and fluorescein. Surface adsorption was observed in separations of Chromeo P503 labeled myoglobin and cytochrome c but was significantly reduced compared to previously reported glass devices. Peak widths of < 30 s were observed for both proteins. For comparison, Chromeo P503 labeled myoglobin and cytochrome c adsorb strongly to the surface of glass µFFE devices resulting in peak widths >20 min. A 2D nLC × µFFE separation of a Chromeo P503 labeled tryptic digest of BSA was performed to demonstrate the high peak capacity possible due to the low surface adsorption in the 3D printed ABS devices, even in the absence of surface coatings or buffer additives.     

Simultaneous determination of the styrene unit content and assessment of molecular weight of triblock copolymers in adhesives by a size exclusion chromatography method

The content of styrene units in nonhydrogenated and hydrogenated styrene‐butadiene‐styrene and styrene‐isoprene‐styrene triblock copolymers significantly influences product performance. A size exclusion chromatography method was developed to determine the average styrene content of triblock copolymers blended with tackifier in adhesives. A complete separation of the triblock copolymer from the other additives was realized with size exclusion chromatography. The peak area ratio of the UV and refraction index signals of the copolymers at the same effective elution volume was correlated to the average styrene unit content using nuclear magnetic resonance spectroscopy with commercial copolymers as standards. The obtained calibration curves showed good linearity for both the hydrogenated and nonhydrogenated styrene‐butadiene‐styrene and styrene‐isoprene‐styrene triblock copolymers (r  = 0.974 for styrene contents of 19.3–46.3% for nonhydrogenated ones and r  = 0.970 for the styrene contents of 23–58.2% for hydrogenated ones). For copolymer blends, the developed method provided more accurate average styrene unit contents than nuclear magnetic resonance spectroscopy provided. These results were validated using two known copolymer blends consisting of either styrene‐isoprene‐styrene or hydrogenated styrene‐butadiene‐styrene and a hydrocarbon tackifying resin as well as an unknown adhesive with styrene‐butadiene‐styrene and an aromatic tackifying resin. The methodology can be readily applied to styrene‐containing polymers in blends such as poly(acrylonitrile‐butadiene styrene).     

Electroosmotic flow in fused deposition modeling (FDM) 3D-printed microchannels

Electroosmotic flow (EOF) was determined in tridimensional (3D)-printed microchannels with dimensions smaller than 100 µm. Fused deposition modeling 3D printing using thermoplastic filaments of PETG (polyethylene terephthalate glycol), PLA (polylactic acid), and ABS (acrylonitrile butadiene styrene) were used to fabricate the microchannels. The current monitoring method and sodium phosphate solutions at different pH values (3–10) were used for the EOF mobility (µ_EOF) measurements, which ranged from 2.00 × 10⁻⁴ to 12.52 × 10⁻⁴ cm² V⁻¹ s⁻¹. The highest and the smallest µ_EOF were obtained for the PLA and PETG microchannels, respectively. Adding the cationic surfactant cetyltrimethylammonium bromide to the sodium phosphate solution caused EOF direction reversion in all the studied microchannels. The obtained results can be interesting for developing 3D-printed microfluidic devices, in which EOF is relevant.     

Influence of multiwall carbon nanotubes on morphology and electrical conductivity of PP/ABS blends

Polypropylene (PP) and acrylonitrile‐butadiene‐styrene (ABS) blends with multiwall carbon nanotubes (MWNT) were prepared by melt mixing. PP/ABS blends without MWNT revealed coarse co continuous structures on varying the ABS content from 40 to 70 wt %. Bulk electrical conductivity of the blends showed lower percolation threshold (0.4–0.5 wt %) in the 45/55 co continuous blends whereas the percolation threshold was between 2 and 3 wt % in matrix‐particle dispersed morphology of 80/20 blends. Interestingly, droplet size was observed to decrease with addition of MWNT above percolation threshold in 80/20 blends. Further, the bulk electrical conductivity was found to be dependent on the melt flow index of PP. The non‐polar or weakly polar nature of blends constituents resulted in the temperature independent dielectric constant, dielectric loss, and DC electrical conductivity. Rheological analysis revealed the formation of 3D network‐like structure in 80/20 PP/ABS blends at 3 wt % MWNT. An attempt was made to understand the relationship between rheology, morphology, and electrical conductivity of these blends. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2286–2295, 2008     

Thermal behaviour of binary and ternary copolymers containing acrylonitrile

Three types of acrylonitrile copolymers (acrylonitrile-styrene-butadiene copolymer (ABS¹), acrylonitrile-styrene random copolymer (SAN²) and acrylonitrile-butadiene random copolymer (BAN³) were studied by thermogravimetry (TG/DTG⁴) and by pyrolysis in a semi-batch process at 450 °C in order to find structure–thermal behaviour relationships. The overlapped thermo-oxidative degradation processes were separated and the corresponding kinetic parameters were calculated. The TG/DTG studies have evidenced that the styrene-acrylonitrile interactions stabilize the nitrile groups reacting by chain scission rather than cyclization and destabilize the styrene units. Also, the cyclization of the acrylonitrile units in ABS is favoured by interactions with the styrene and butadiene units. The pyrolysis behaviour evidenced that the styrene-acrylonitrile interactions in SAN and ABS lead to the formation of 4-phenylbutyronitrile as the most important decomposition compound. ABS shows similar composition of the degradation oil with SAN copolymer therefore in the ABS the styrene-butadiene interactions are less important than those between styrene and acrylonitrile units.     

Microphase separation in poly(acrylonitrile–butadiene–styrene) (ABS) studied with paramagnetic spin probes. I. Electron spin resonance spectra

Microphase separation in poly(acrylonitrile–butadiene–styrene) (ABS) was studied as a function of the butadiene content and method of preparation with electron spin resonance (ESR) spectra of nitroxide spin probes. Results for the ABS polymers were evaluated by comparison with similar studies of the homopolymers polybutadiene (PB), polystyrene (PS), and polyacrylonitrile (PAN) and the copolymers poly(styrene‐co‐acrylonitrile) (SAN) and poly(styrene‐co‐butadiene) (SB). Two spin probes were selected for this study: 10‐doxylnonadecane (10DND) and 5‐doxyldecane (5DD). The probes varied in size and were selected because their hydrocarbon backbone made them compatible with the polymers studied. The ESR spectra were measured in the temperature range 120–420 K and were analyzed in terms of line shapes, line widths, and hyperfine splitting from the ¹⁴N nucleus; the appearance of more than one spectral component was taken as an indication of microphase separation. Only one spectral component was detected for 10DND in PB, PS, and PAN and in the copolymers SAN and SB. In contrast, two spectral components differing in their dynamic properties were detected for both probes in the three types of ABS samples studied and were assigned to spin probes located in butadiene‐rich domains (the fast component) and SAN‐rich domains (the slow component). The behavior of the fast component in ABS prepared by mass polymerization suggested that the low‐T_g (glass‐transition‐temperature) phase was almost pure PB. The corresponding phase in ABS prepared by emulsion grafting also contained styrene and acrylonitrile monomers. A redistribution of the spin probes on heating occurred with heating near the T_g of the SAN phase, suggesting that the ABS polymers as prepared were not in thermodynamic equilibrium. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 415–423, 2002; DOI 10.1002/polb.10109     

Novel,well‐defined polystyrene with a fluorine cluster end‐capped group: Synthesis,characterization, and surface properties

Novel, well‐defined fluorinated polystyrene was synthesized for the first time via the controlled radical polymerization of styrene through a relatively simple process and was characterized with ¹H NMR, ¹⁹F NMR, and gel permeation chromatography. The surface properties of polystyrene and poly(acrylonitrile‐co‐butadiene‐co‐styrene) films were modified with the obtained polymers. X‐ray photoelectron spectroscopy measurements of the air‐side surface composition of the modified poly(acrylonitrile‐co‐butadiene‐co‐styrene) films showed that fluorine enriched the outermost surface, resulting in fantastic surface properties that came close to those of poly(tetrafluoroethylene). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3853–3858, 2006     

A new hybrid nanocomposite prepared by emulsion copolymerization of ABS in the presence of clay

The preparation and characterizations of new hybrid organic–inorganic nanocomposites consisting of acrylonitrile–butadiene–styrene terpolymer and a Na⁺‐exchanged montmorillonite (MMT) are described by direct intercalation through one‐step emulsion polymerization. Those products were purified by successive hot acetone and toluene extraction, respectively, for more than 2 days. The IR spectra for the purified samples revealed the characteristic absorbances as a result of those of styrene, butadiene, acrylonitrile, and MMT. X‐ray diffraction spectra of the composites showed the enlarged 001 d‐spacing as much as 1.75 nm, but no signals were found for the partial insertion of copolymer chains. Moreover, it was evident that this direct intercalation was not accompanied by delamination of the clay interlayer. The thermogravimetric analytic measurement for the purified product confirmed that the onset temperature of decomposition was transferred to the higher temperature region as much as 40–50 °C. Morphological observations by transmission electron microscopy, scanning electron microscopy, and optical micrography demonstrated homogeneous dispersion of MMT particles in the copolymer matrix. The possible physical picture of this direct intercalation was discussed in terms of swelling characteristics of compacted bentonite and the monomer containing micelle sizes. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 719–727, 2001     

Viscoelastic effects in cutting of elastomers by a sharp object

The cutting behavior of elastomers by a sharp object was investigated using various elastomers such as acrylonitrile–butadiene rubber (NBR), styrene–butadiene rubber (SBR), and natural rubber (NR). The effects of crosslinking density, cutting rate, and temperature on the cutting energy of elastomers were investigated. The cutting behavior of swollen elastomers was also investigated. It was found that the cutting energy increased as the molecular weight between crosslinks increased. It was also found that the cutting energies of various elastomers did not yield a single line. Moreover, even in the threshold condition of cutting process, the cutting energy was much higher than the threshold fracture energy. These results suggest that the cutting behavior cannot be explained by only a C C bond rupture process, but it includes other energy dissipation processes. The curves for cutting energies obtained at different cutting rates and temperatures were well superimposed on a single master curve when they were shifted using the WLF (Williams, Landel, and Ferry) equation. Therefore, it is supposed that the cutting of elastomers by a sharp object includes viscoelastic energy dissipation process and is the viscoelastic behavior. It was also found that the variation of cutting energy over a considerable range of effective rates was smaller than that of the tear energy. It is attributed to the fact that the change of the crack tip diameter, i.e., roughening or reduction, was restricted by the diameter of razor blade. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1283–1291, 1998     

Homopolymers and copolymers of acrylates and methacrylates of homoterpenylmethyl carbinol and α-campholenol

Acrylates and methacrylates of homoterpenylmethyl carbinol and α-campholenol were homopolymerized. Copolymers with each other and acrylonitrile were studied. Terpolymers of the acrylate of homoterpenylmethyl carbinol and the acrylate of α-campholenol with butadiene and styrene or acrylonitrile were also prepared. The lactone ring in the homopolymer of methacrylate of homoterpenylmethyl carbinol was opened up under basic conditions at room temperature, yielding a water-soluble polymer. Films of this polymer were cast from a water solution. The acrylate of homoterpenylmethyl carbinol gave a high molecular weight copolymer with acrylonitrile which could be molded into a transparent, extremely tough, film. The terpolymers of the acrylate of homoterpenylmethyl carbinol with butadiene and styrene or acrylonitrile were obtained in high yield and could be molded into strong, rubbery films. Several polymers were epoxidized and cured with p-phenylenediamine.     

Formation of nanocomposites of styrene and its copolymers using graphite as the nanomaterial

Graphite‐polymer nanocomposites were prepared by melt blending of various graphites (virgin graphite, expandable graphites, and expanded graphite) with polystyrene and its copolymers (acrylonitrile‐butadiene‐styrene (ABS) and high‐impact polystyrene (HIPS)). Nanocomposites were characterized by X‐ray diffraction, cone calorimetry, thermogravimetric analysis and evaluation of mechanical properties. Nanocomposite formation occurs at higher loadings (3–5%) of expandable graphites but not for virgin or expanded graphite. Copyright © 2005 John Wiley & Sons, Ltd.     

Effect of the Free Quenching on Mechanical and Thermomechanical Properties of ABS

The purpose of this work was to investigate the influence of thermal annealing and quenching on mechanical, and thermomechanical properties of acrylonitrile butadiene styrene (ABS). The free quenching was applied over a temperature range starting from a temperature slightly above T_g to temperatures below 0°C. The improvement of the impact strength is linked to the cavitation of the rubber particles close to the samples surface. The existence of a relaxation mode located around–10°C may participate to the relaxation of the residual stresses when the sample is quenched under 0°C, this phenomenon would promote cavitation.     

Generic crack patterns in rubber‐modified polymers under biaxial stress states

The damage mechanisms in three different systems, namely, acrylonitrile‐butadiene‐styrene, methacrylate‐butadiene‐styrene modified poly(vinyl chloride), and styrene‐butadiene‐styrene have been investigated. The damage was analyzed over a range of biaxial stress states with confocal microscopy and scanning electron microscopy. The macroscopic yield followed a linear behavior for all the systems in an octahedral shear stress versus mean stress plot, whereas popular models for this class of materials predicted a nonlinear response. Over a certain range of biaxial stress states, a damage pattern generic to all the systems was observed. The damage pattern consisted of an array of cracks propagating perpendicular to the direction of the maximum tensile principal stress and arranged itself in a more or less periodic fashion. There was also self‐similarity in the patterns at various length scales. Similar patterns have also occurred in several other polymeric systems. The interaction in the ensemble of cracks created seems to lead to stress reduction at the crack tips, thereby limiting the crack sizes. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2248–2256, 2003     

Preparation of fluorine containing hybrid coatings: investigation of coating performance onto ABS and PMMA substrates

UV‐curable fluorinated organic–inorganic hybrid coatings were prepared by the sol–gel technique. Perfluorinated urethane modified alkoxysilane was synthesized by the reaction between perfluoro alcohol and 3‐isocyanatopropyltrimethoxysilane. The prepared formulations were applied onto poly(methyl methacrylate) (PMMA) and acrylonitrile butadiene styrene (ABS) panels and polymerized by UV‐curing. The properties of the hybrid coatings such as hardness, chemical resistance, thermal stability, surface morphology, double bond conversion, and also contact angle measurements were investigated. Contact angle measurements have shown that the addition of fluorinated silane precursor to the hybrid system improved the water repellency and increased the contact angle from 65° to 106°. Copyright © 2009 John Wiley & Sons, Ltd.     

Influence of crosslinking on mechanical and dielectric properties of nitrile-butadiene-rubber

Several copolymers of acrylonitrile with butadiene (different acrylonitrile content, different molecular weight), uncrosslinked and crosslinked by tetramethylthiuramdisulfide or radiation, are investigated by dynamic mechanical measurements (10^–4 Hz to 100 Hz). The viscoelastic behaviour at very low frequencies is strongly influenced by molecular weight and crosslinking whereas the main relaxation (glass process) remains nearly the same. Stress strain curves (Mullins effect) and some dielectric measurements are also reported.     

Unique rheological behavior of rubber based nanocomposites

Montmorillonite clay (N) based nanocomposites were prepared using three different grades of acrylonitrile butadiene rubber (NBR) (19%, 34%, and 50% acrylonitrile contents), styrene butadiene rubber (SBR), and polybutadiene rubber (BR). Rheological study was carried out on these nanocomposites at three different temperatures (110 °C, 120 °C, and 130 °C) over a range of shear rates for comparison. The results showed that the shear viscosity decreased with increasing shear rate and incorporation of the unmodified (N) and the modified (OC) fillers up to a certain loading, when the results were compared with the gum rubber. This effect became more prominent with increasing polarity of the rubber. The die swell, on the other hand, decreased with loading of N and OC. With increasing filler volume fraction, the die swell further decreased. Decrease of viscosity with concomitant decrease of die swell is unique in such systems. Consecutive runs of the same sample over different shear rates increased the viscosity. The results were explained with the help of X‐Ray Diffraction (XRD) data and Transmission Electron Microscopy (TEM).© 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1854–1864, 2005     

Co‐continuous Polyamide 6 (PA6)/Acrylonitrile‐Butadiene‐Styrene (ABS) Nanocomposites

Summary: Polyamide 6 (PA6)/acrylonitrile‐butadiene‐styrene (ABS) (40/60 w/w) nanocomposites with a novel morphology were prepared by the melt mixing of PA6, ABS and organoclay. The blend nanocomposites had a co‐continuous structure, in which both PA6 and styrene‐acrylonitrile (SAN) were continuous phases. It was found that the toughening rubber particles were only located in the SAN phase and the strengthening clay platelets were selectively dispersed in the PA6 phase. The co‐continuous nanocomposites showed greatly improved mechanical properties over the whole temperature range when compared with the same blend sample without clay.

Schematic diagram for the co‐continuous ABS/PA6 blend nanocomposite.     

The influence of the arrangement of styrene in methyl methacrylate/butadiene/styrene on the properties of PMMA/SAN/MBS blends

A series of methyl methacrylate‐butadiene‐styrene (MBS) core–shell impact modifiers were prepared by grafting styrene (St) and methyl methacrylate (MMA) onto polybutadiene (PB) or styrene‐butadiene rubber (SBR) seed latex in emulsion polymerization. All the MBS modifiers were designed to have the same total chemical composition, and Bd/St/MMA equaled 39/31/30, which was a prerequisite for producing transparent blends with poly(MMA)/styrene‐acrylonitrile (PMMA/SAN) matrix copolymers. Under this composition, different ways of arrangement for styrene in MBS led to the different structure of MBS modifier. The concentration of PB or SBR rubber of MBS in PMMA/SAN/MBS blends was kept at a constant value of 15 wt.%. The effects of arrangement of St in MBS on the mechanical and optical properties of PMMA/SAN/MBS blends were investigated. The results indicated that Izod impact strength of PMMMA/SAN/MBS blend with the amount of St grafted on core in MBS was higher than that of blend with the amount of St copolymerized with Bd in core of MBS, while the transparency of blend is opposite. From transmission electron microscopy, it was found that the arrangement of St in MBS influenced the dispersion of blend, which led to different toughness. Copyright © 2013 John Wiley & Sons, Ltd.     

Polymer matrix influence on stability of wood polymer composites

The aim of the presented work is to show the influence of the various polymer matrices and the different amounts of the cellulose filler on the composites properties. Samples based on polypropylene, polystyrene, polyoxymethylene, acrylonitrile butadiene styrene, polyester resin, and polylactic acid with different contents of cellulose fibers were prepared by injection molding process. The mechanical and dielectric properties of these composites were studied in order to check whether investigated wood polymer composites fulfill requirements for their application in electrical devices. For all tested composites, a linear increase of modulus with cellulose content was observed. Addition of cellulose to the tested polymers significantly reduces strain at break. In the case of polypropylene and polyoxymethylene composites, the tensile strength increases with the content of the filler. For other materials, there is an inverse relationship, namely the addition of cellulose decreases the tensile strength. The electrical strength decrease was observed with increased cellulose content for the majority of the investigated composites. Polar groups incorporated by cellulose fibers have led to dielectric constant increase. Furthermore, aging of composites in mineral oil and evaluation of water uptake for wood–plastic samples were performed. Wood polymer composites have changed significantly after aging. The water diffusion coefficients were determined, and the significant influence of the amount of cellulose on the water absorption was shown. Copyright © 2015 John Wiley & Sons, Ltd.     

Investigation of some physicochemical properties of camphor sulfonic acid (CSA)–doped poly(o-anisidine) (PoAN) and CSA-doped PoAN/ABS composites

Camphor sulfonic acid (CSA)–doped poly(o-anisidine) (PoAN) has been found to possess the electrical conductivity of 10 S/cm. This value is rather low compared to that of (≈200 S/cm) CSA-doped polyaniline, which may arise from a limited transformation of coil-like conformation to an expanded one. Viscosity data and optical absorption spectra provided strong evidence for the existence of coil-like CSA-doped PoAN chains in m-cresol. The shift of IR bands of benzenoid and quinoid rings toward a lower wave number and the appearance of the bands at ≈1600 and 1173 cm⁻¹ (the IR is inactive but becomes active on doping) suggested the protonation of CSA-doped PoAN. The thermogravimetric profile of CSA-doped PoAN showed a five-step decomposition pattern with the thermal stability up to 134 °C. The mass spectra taken simultaneously with the thermogram revealed that dopant CSA is completely eliminated around 360 °C, but the breakdown of polymer chains does not occur very briskly at this temperature. Composites of CSA-doped PoAN with insulating acrylonitrile–butadiene–styrene copolymer (ABS) were fabricated, and it was found that the composites showed a percolation behavior in which the electrical conductivity rose sharply at about 4 weight % of CSA-doped PoAN in the ABS composite. The STM data demonstrated the formation of a continuous path at the percolation threshold. The Poole–Frenkel effect was observed for the conduction scheme in the CSA-doped PoAN/ABS composite. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4596–4604, 1999