富氮洋葱碳包覆的Ni/NiFe2O4纳米棒析氧电催化剂

将镍铁金属配位聚合物前驱体在惰性气氛下热分解制备了富氮洋葱碳(ONC)包覆的Ni/Ni Fe_2O_4多孔纳米棒复合析氧电催化剂,与Ni@ONC,Ni Fe_2O_4材料及传统Ru O_2催化剂相比,得益于这种富氮洋葱碳包覆的Ni/Ni Fe_2O_4一维多孔纳米异质结构,Ni/Ni Fe_2O_4@ONC材料拥有更优异的导电性能和更大的电化学活性面积(0.149 m F),因而表现出更优异的析氧电催化性能。Ni/Ni Fe_2O_4@ONC纳米棒在1 mol·L~(-1) KOH溶液中,10 m A·cm-2下的析氧过电位仅为299 m V,塔菲尔斜率为73 m V·dec-1,展现出优异的析氧稳定性能。     

A facile nitrogen-doped carbon encapsulation of CoFe2O4 nanocrystalline for enhanced performance of lithium ion battery anodes

Nitrogen-doped (N-doped) carbon encapsulation of CoFe₂O₄ nanocrystalline is achieved by a simple pressure-assisted pyrrole pyrolysis method. The CoFe₂O₄/N-doped carbon nanocomposite (CFO/NC) delivers a capacity of 646.2 mAh g^–1 after 80 cycles at 0.1 C, exhibits stable cycling performance at various rates from 0.2 to 1.6 C and retains a capacity of 662.8 mAh g^–1 as the rate returns back to 0.1 C, showing significantly improved lithium storage reversibility compared to the bare CFO. A different lithiation mechanism of CFO/NC above and below the plateau relative to CFO in the first discharge is analyzed in detail based on the potential profiles and cyclic voltammogram curves. Morphology characterization of the cycled electrodes confirms much better integrity of CFO/NC electrode due to the buffer effect of N-doped carbon coating. Electronic conductivity and electrochemical impedance spectroscopy measurements indicate enhanced electrode reaction kinetics of CFO/NC. All the results contribute to its improved electrochemical performance.     

Multilayered structure of N-carbonenvelopediron oxide/graphene nanocomposites as an improved anode for Li-ion battery

Transition metal oxides with high capacity are considered a promising electrode material for lithium-ion batteries (LIBs). Nevertheless, the huge volume expansion and poor conductivity severely hamper their practical application. In this work, a carbon riveting method is reported to address the above issues by designing multilayered N-doped carbon (N-carbon) enveloped Fe₃O₄/graphene nanosheets. When evaluated as a negative electrode, the N-carbon/Fe₃O₄/graphene nanocomposites demonstrate greatly enhanced electrochemical properties compared with Fe₃O₄/graphene. The N-carbon/Fe₃O₄/graphene presents a superior reversible capacity (807 mAh/g) over Fe₃O₄/graphene (540 mAh/g). Furthermore, it affords a considerable capacity of 550 mAh/g at 1 A/g over 700 cycles, indicating superb cycling stability. The structure-property correlation studies reveal that the carbon riveting layer is essential for enhancing the lithium diffusion kinetics. The good electrochemical properties and effective structure design make the carbon riveting strategy quite general and reliable to manipulate high performance electrodes for future LIBs.     

Nickel and cobalt ferrites nanoparticles: synthesis,study of magnetic properties and their use as magnetic adsorbent for removing lead(II) ion

Nano-sized nickel ferrite (NiFe₂O₄) and cobalt ferrite particles (CoFe₂O₄) were successfully synthesized using a hydrothermal method. Techniques of X-ray diffraction, scanning electron microscope, Fourier transform infrared spectrometer, energy dispersive X-ray spectroscopy, vibrating sample magnetometer and transmission electron microscope have been used to characterize and study the as-synthesized NiFe₂O₄ and CoFe₂O₄ products. The results showed that the average size of the nickel and cobalt ferrite nanoparticles is smaller than 10 and 100 nm, respectively. The results of magnetic measurement showed that the synthesized NiFe₂O₄ and CoFe₂O₄ nanoparticles were superparamagnetic and soft ferromagnetic materials, respectively. Study of adsorption behavior showed that these nanoparticles can act as a good adsorbent for removing Pb²⁺.     

Comparative study of the synthesis of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> and NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript> in silica through the polymerized complex route of the sol–gel method

In this work the synthesis of CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ nanocomposites was studied via the sol–gel method, using the polymerized complex route. The polymerized precursors obtained by the reaction of citric acid, ethylene glycol, tetraethylorthosilicate, ferric nitrate, and cobalt nitrate or nickel chloride were characterized by nuclear magnetic resonance (NMR) and infrared (IR) spectroscopy. NMR and IR spectra of the precursors, without and with metallic ions, show the formation of polymeric chains with ester and ether groups and complexes of metal-polymeric precursor. The nanocomposites were obtained by the thermal decomposition of the organic fraction and characterized by X-ray diffraction (XRD) and vibrating sample magnetometry (VSM). XRD patterns show the formation of CoFe₂O₄ and NiFe₂O₄ in an amorphous silica matrix above 400 °C in both cases. When the calcination temperature was 800 °C the particle size of the crystalline phases, calculated using the Scherrer equation, reached ∼35 nm for the two oxides. VSM plots show the ferrimagnetic behavior that is expected for this type of magnetic material; the magnetization at 12.5 KOe of the CoFe₂O₄-SiO₂ and NiFe₂O₄-SiO₂ compounds was 29.5 and 17.4 emu/g, respectively, for samples treated at 800 °C.     

Antimony anchored in MoS2 nanosheets with N-doped carbon coating to boost potassium storage performance

Potassium ions batteries (PIBs) have been considered as promising energy storage systems owning to potassium rich natural abundances. However, the difficult reaction kinetics and poor cycling of electrode restrict the further development of PIBs. In this work, antimony anchored in MoS₂ nanosheets with N-doped carbon coating (Sb/MoS₂/NCs) are prepared and evaluated as anode for PIBs. In the unique Sb/MoS₂/NCs structure, the volume expansion of Sb particles could be effectively buffered by the around MoS₂ structure. The defects in MoS₂ nanosheets provide more electrochemical reaction sites for sufficient K⁺ insertion/extraction. Furthermore, the N-doped carbon can further accommodate the volume expansion and improve the electronic conductivity of Sb/MoS₂/NCs composites. Due to the above advantages, the Sb/MoS₂/NCs anode delivers a capacity of 235 mAh/g at 50 mA/g after 78 cycles. This work provides a prospective strategy to design advanced anode materials for PIBs using MoS₂ and antimony composites.     

Preparation of CoFe2O4/sawdust and NiFe2O4/sawdust magnetic nanocomposites for removal of oil from the water surface

In this study, CoFe₂O₄/Sawdust and NiFe₂O₄/Sawdust magnetic nanocomposites were synthesized using a hydrothermal method, and then characterized using X-ray powder diffraction, Infrared, scanning electron microscopy, Brunauer–Emmett–Teller/Barrett–Joyner–Halenda, and vibrating-sample magnetometer techniques. In this study, unmodified sawdust (US), modified sawdust (MS), unmodified CoFe₂O₄/sawdust (UCS), modified CoFe₂O₄/sawdust (MCS), unmodified NiFe₂O₄/sawdust (UNS), and modified NiFe₂O₄/Sawdust (MNS) magnetic nanocomposites, which are inexpensive, economical, environmentally friendly absorbents, and have a high selective hydrophobic, were used for the removal of oil from the water surface. The results show that the UCS, MCS, UNS, and MNS magnetic nanocomposites can selectively absorb the oil spreading on the water surface, due to its superhydrophobicity and superoleophilicity, and can be easily collected from water under the influence of a magnetic field. In addition, the results showed that the absorbents reach their equilibrium at the 30-min mark. Among all the absorbents, the MNS magnetic nanocomposite showed the maximum absorption capacity (18.172 g/g) at the 40-min mark. The results of the kinetic studies showed that the second-order kinetic equation with the highest correlation coefficient had the best fit with the experimental results.     

Development of magnetic,ferrite supported palladium catalysts for 2,4-dinitrotoluene hydrogenation

Cobalt, copper, and nickel ferrite spinel nanoparticles have been synthesized by using a combination of sonochemical treatment and combustion. The magnetic nanoparticles have been used as supports to prepare ~4 wt% palladium catalysts. The ferrites were dispersed in an ethanolic solution of Pd(II) nitrate by ultrasonication. The palladium ions were reduced to metallic Pd nanoparticles, which were then attached to the surface of the different metal oxide supports. Thus, three different catalysts (Pd/CoFe₂O₄, Pd/CuFe₂O₄, Pd/NiFe₂O₄) were made and tested in the hydrogenation of 2,4-dinitrotoluene (DNT). A possible reaction mechanism, including the detected species, has been envisaged based on the results. The highest 2,4-diaminotoluene (TDA) yield (99 n/n%) has been achieved by using the Pd/NiFe₂O₄ catalyst. Furthermore, the TDA yield was also reasonable (84.2 n/n%) when the Pd/CoFe₂O₄ catalyst was used. In this case, complete and easy recovery of the catalyst from the reaction medium is ensured, as the ferrite support is fully magnetic. Thus, the catalyst is very well suited for applicationy in the hydrogenation of DNT or other aromatic nitro compounds.     

Nanostructured ferrite/graphene/polyaniline using for supercapacitor to enhance the capacitive behavior

Graphene nanosheets, polyaniline (PANI), and nanocrystallites of transition metal ferrite {Fe₃O₄ (Mag), NiFe₂O₄ (NiF), and CoFe₂O₄ (CoF)} have been prepared and characterized via XRD, FTIR, SEM, TEM, UV–vis spectroscopy, cyclic voltammetry, galvanostatic charge discharges, and impedance spectroscopy. Electrochemical measurements showed that supercapacitances of hybrid electrodes made of the ternary materials are higher than that of hybrid electrode made of binary or single material. The ternary hybrid CoF/graphene (G)/PANI electrode exhibits a highest specific capacitance reaching 1123 Fg^?1, an energy density of 240 Wh kg^?1 at 1 A g^?1, and a power density of 2680 Wkg^?1 at 1 A g^?1 and outstanding cycling performance, with 98.2% capacitance retained over 2000 cycles. The extraordinary electrochemical performance of the ternary CoF/G/PANI hybrid can be attributed to the synergistic effects of the individual components. The PANI conducting polymer enhances an electron transport. The Ferrite nanoparticles prevent the restocking of the carbon sheets and provide Faradaic processes to increase the total capacitance.     

Superior Electrochemical Properties of Nanofibers Composed of Hollow CoFe2O4 Nanospheres Covered with Onion‐Like Graphitic Carbon

Nanofibers composed of hollow CoFe₂O₄ nanospheres covered with onion‐like carbon are prepared by applying nanoscale Kirkendall diffusion to the electrospinning process. Amorphous carbon nanofibers embedded with CoFe₂@onion‐like carbon nanospheres are prepared by reduction of the electrospun nanofibers. Oxidation of the CoFe₂‐C nanofibers at 300 °C under a normal atmosphere produces porous nanofibers composed of hollow CoFe₂O₄ nanospheres covered with onion‐like carbon. CoFe₂ nanocrystals are transformed into the hollow CoFe₂O₄ nanospheres during oxidation through a well‐known nanoscale Kirkendall diffusion process. The discharge capacities of the carbon‐free CoFe₂O₄ nanofibers composed of hollow nanospheres and the nanofibers composed of hollow CoFe₂O₄ nanospheres covered with onion‐like carbon are 340 and 930 mA h g^?1, respectively, for the 1000th cycle at a current density of 1 A g^?1. The nanofibers composed of hollow CoFe₂O₄ nanospheres covered with onion‐like carbon exhibit an excellent rate performance even in the absence of conductive materials.     

Particle size,morphology, and properties of transition metal ferrospinels of the MFe<Subscript>2</Subscript>O<Subscript>4</Subscript> (M = Co,Ni, Zn) type,produced by glycine-nitrate combustion

Ferrites-spinels of the MFe₂O₄ type (M = Co, Ni, Zn), produced by glycine-nitrate combustion were studied. A physicochemical study of ferrite samples was performed by X-ray fluorescence analysis, scanning electron microscopy, X-ray phase analysis, and X-ray spectroscopy. The average size of the coherent scanning region was found to be (nm): 28 ± 2 for CoFe₂O₄, 32 ± 2 for NiFe₂O₄, and 26 ± 2 for ZnFe₂O₄. Magnetic characteristics were determined by the NMR method. The specific residual magnetization, specific saturation magnetization, and coercive force were, respectively, 14.1 A m² kg^?1, 20.1 A m² kg^?1, 31800 A m^?1 for CoFe₂O₄; 4.4 A m² kg^?1, 23.1 A m² kg^?1, 6550 A m^?1 for NiFe₂O₄; and 5.1 A m² kg^?1, 18.3 A m² kg^?1, 3200 A m^?1 for ZnFe₂O₄. Their magnetic properties show that the resulting ferrospinel powders can be used in the following fields of technology: CoFe₂O₄ in those areas where heat transfer is necessary (hyperthermia) and in development of data storage media; NiFe₂O₄ and ZnFe₂O₄ in those areas where low heat exchange is necessary, ZnFe₂O₄ for fast remagnetization and NiFe₂O₄ as a core or shell for transportation of other substances. The ferrospinel samples compare well in magnetic properties with their foreign commercial analogs, which makes these compounds commercially viable.     

Thermal behavior of Ni,Co and Fe succinates embedded in silica matrix

This paper presents the thermal behavior of Co, Ni and Fe succinates obtained by sol-gel synthesis using Co(II), Ni(II) and Fe(III) nitrates, 1,4-butanediol and tetraethyl orthosilicate as reactants. The thermal analysis revealed the formation of succinates at 413–453 K and their decomposition to ferrites at 503–623 K. The rate constants for the decomposition of succinates to ferrites, calculated using the isotherms at 473, 523, 573 and 623 K, were used to determine the activation energy of each ferrite (NiFe₂O₄, Ni_0.3Co_0.7Fe₂O₄, Ni_0.7Co_0.3Fe₂O₄ and CoFe₂O₄) embedded in the silica matrix. By increasing the Ni content in the mixed Ni–Co ferrites, the activation energy decreases from 13.530 to 1.944 kJ mol^?1. The formation and decomposition of succinate precursors and the formation of silica matrix were confirmed by FT-IR spectroscopy, while the formation of CoFe₂O₄ and NiFe₂O₄ single-phases embedded in the silica matrix was confirmed by X-ray diffraction analysis. The nanocrystallites size decreases from 31.7 (CoFe₂O₄) to 18.5 nm (NiFe₂O₄). The optical band gap of mixed Co–Ni ferrites was significantly higher than that corresponding to CoFe₂O₄. The photocatalytic activity of the samples was evaluated against Rhodamine B under visible light. All the samples have photocatalytic activities, the best performance being obtained in the case of Ni_0.7Co_0.3Fe₂O₄.

     

A Facile Molten‐Salt Route for Large‐Scale Synthesis of NiFe2O4 Nanoplates with Enhanced Lithium Storage Capability

Binary metal oxides have been deemed as a promising class of electrode materials for high‐performance lithium ion batteries owing to their higher conductivity and electrochemical activity than corresponding monometal oxides. Here, NiFe₂O₄ nanoplates consisting of nanosized building blocks have been successfully fabricated by a facile, large‐scale NaCl and KCl molten‐salt route, and the changes in the morphology of NiFe₂O₄ as a function of the molten‐salt amount have been systemically investigated. The results indicate that the molten‐salt amount mainly influences the diameter and thickness of the NiFe₂O₄ nanoplates as well as the morphology of the nanosized building blocks. Cyclic voltammetry (CV) and galvanostatic charge–discharge measurements have been conducted to evaluate the lithium storage properties of the NiFe₂O₄ nanoplates prepared with a Ni(NO₃)₂/Fe(NO₃)₃/KCl/NaCl molar ratio of 1:2:20:60. A high reversible capacity of 888 mAh g^?1 is delivered over 100 cycles at a current density of 100 mA g^?1. Even at a current density of 5000 mA g^?1, the discharge capacity could still reach 173 mAh g^?1. Such excellent electrochemical performances of the NiFe₂O₄ nanoplates are contributed to the short Li⁺ diffusion distance of the nanosized building blocks and the synergetic effect of the Ni²⁺ and Fe³⁺ ions.     

Efficient magnetic CoFe2O4 nanocrystal catalyst for aerobic oxidation of cyclohexane prepared by sol–gel auto-combustion method: effects of catalyst preparation parameters

Six magnetic spinel-type CoFe₂O₄ samples were prepared in the form of powder by a simple sol–gel auto-combustion method from precursor solutions with different metal concentrations (0.1–0.3 mol L^?1) and pH values (<1–10). The samples were characterized by X-ray diffractometry, Fourier transform infrared spectrophotometry, transmission electron microscopy and N₂-physisorption. Their catalytic performances for oxidation of cyclohexane were evaluated using oxygen as oxidant in the absence of solvents. The results show that pH values and metal concentrations of precursor solutions play important roles in the sizes, dispersions and morphologies of the CoFe₂O₄ nanoparticles, and thus in their catalytic performances. The sample resulted from precursor solution under the conditions of pH = 7 and metal concentration = 0.1 mol L^?1 with the largest surface area, exhibited the best catalytic performance with the highest cyclohexane conversion of 13.7 % and selectivity of 93.9 % for cyclohexanol and cyclohexanone. The CoFe₂O₄ nanocrystal is also found an efficient catalyst for oxidation of aliphatic and aromatic alkenes.     

Calcination-Free Synthesis of Well-Dispersed and Sub-10 nm Spinel Ferrite Nanoparticles as High-Performance Anode Materials for Lithium-Ion Batteries: A Case Study of CoFe2O4

Spinel ferrites are promising anode materials for lithium-ion batteries (LIBs) owing to their high theoretical specific capacities. However, their practical application is impeded by inherent low conductivity and severe volume expansion, which can be surpassed by increasing the surface-to-volume ratio of nanoparticles. Currently, most methods produce spinel ferrite nanoparticles with large size and severe aggregation, degrading their electrochemical performance. In this study, a low-temperature aminolytic route was designed to synthesize sub-10 nm CoFe₂O₄ nanoparticles with good dispersion through carefully exploiting the reaction of acetates and oleylamine. The performance of CoFe₂O₄ nanoparticles obtained by a traditional co-precipitation method was also investigated for comparison. This work demonstrates that CoFe₂O₄ nanoparticles synthesized by the aminolytic route are promising as anode materials for LIBs. Besides, this method can be extended to design other spinel ferrites for energy storage devices with superior performance by simply changing the starting material, such as MnFe₂O₄, MgFe₂O₄, ZnFe₂O₄, and so on.     

Simultaneous formation of ferrite nanocrystals and deposition of thin films via a microwave-assisted nonaqueous sol–gel process

Combination of the surfactant-free nonaqueous sol–gel approach with the microwave technique makes it possible to synthesize Fe₃O₄, CoFe₂O₄, MnFe₂O₄, and NiFe₂O₄ nanoparticles of about 5–6 nm and with high crystallinity and good morphological uniformity. The synthesis involves the reaction of metal acetates or acetylacetonates as precursors with benzyl alcohol at 170 °C under microwave irradiation of 12 min. Immersion of glass substrates in the reaction solution results in the deposition of homogeneous metal ferrite films whose thickness can be adjusted through the precursor concentration. If preformed nickel nanoparticles are used as a type of curved substrate, the ferrite nanoparticles coat the seeds and form core–shell structures. These results extend the microwave-assisted nonaqueous sol–gel approach beyond the simple synthesis of nanoparticles to the preparation of thin films on flat or curved substrates.     

Nitrogen-doped mesoporous carbon nanospheres loaded with cobalt nanoparticles for oxygen reduction and Zn–air batteries

Mesoporous carbon supported with transition metals nanoparticles performs desired activities for oxygen reduction reaction (ORR) and clean energy conversion devices such as Zn–air batteries. In this work, we synthesized N-doped mesoporous carbon loaded with cobalt nanoparticles (CoMCN) through self-assembly method. There are sufficient mesopores on the carbon substrate which stem from the pore-forming agent. These mesopores can provide enough accessible active sites and profitable charge/mass transport for ORR. The high content of pyridinic and graphitic N is beneficial for promoting O₂ adsorption and reduction. The smaller value of I_D/I_G indicates the higher degree of graphitization of CoMCN, providing better electronic conductivity. The half-wave potential of CoMCN is 0.865 V in basic solution, which is 24 mV more positive than that of the commercial Pt/C (0.841 V). In addition, CoMCN performs excellent methanol tolerance and stability under both basic and acidic conditions. The Zn–air battery assembled with CoMCN performs the larger power density and open-circuit voltage than the commercial Pt/C-based battery, indicating the potential application in energy conversion systems. This work provides thoughtful ideas for fabricating transition metal nanoparticles based porous carbon for electrocatalysis and metal–air batteries.     

Wintersweet‐Flower‐Like CoFe2O4/MWCNTs Hybrid Material for High‐Capacity Reversible Lithium Storage

CoFe₂O₄/multiwalled carbon nanotubes (MWCNTs) hybrid materials were synthesized by a hydrothermal method. Field emission scanning electron microscopy and transmission electron microscopy analysis confirmed the morphology of the as‐prepared hybrid material resembling wintersweet flower “buds on branches”, in which CoFe₂O₄ nanoclusters, consisting of nanocrystals with a size of 5–10 nm, are anchored along carbon nanotubes. When applied as an anode material in lithium ion batteries, the CoFe₂O₄/MWCNTs hybrid material exhibited a high performance for reversible lithium storage. In particular, the hybrid anode material delivered reversible lithium storage capacities of 809, 765, 539, and 359 mA h g^?1 at current densities of 180, 450, 900, and 1800 mA g^?1, respectively. The superior performance of CoFe₂O₄/MWCNTs hybrid materials could be ascribed to the synergistic pinning effect of the wintersweet‐flower‐like nanoarchitecture. This strategy could also be applied to synthesize other metal oxide/CNTs hybrid materials as high‐capacity anode materials for lithium ion batteries.     

Efficient activation of sulfite for reductive-oxidative degradation of chloramphenicol by carbon-supported cobalt ferrite catalysts

Activation of (bi)sulfite (S(IV)) by metal oxides is strongly limited by low electrons utilization.In this study,two carbon-supported cobalt ferrites spinels (Co Fe₂O₄QDs-GO and CoFe₂O₄MOFs-CNTs) have been successfully synthesized by one-step solvothermal method.It was found that both catalysts could efficiently activate S(IV),with rapid reductive dechlorination and then oxidative degradation of a recalcitrant antibiotic chloramphenicol (CAP).Character...     

Tandem magnetization and post‐synthetic metal ion exchange of metal–organic framework: Synthesis,characterization and catalytic study

For the first time, metal‐exchange in a magnetic metal–organic framework (MOF) via tandem magnetization and post‐synthetic modification has been developed. The new magnetic mixed‐metal metal–organic framework nanocomposite, CoFe₂O₄/[Cu_0.63/Zn_0.37‐TMU‐17‐NH₂] (CoFe₂O₄/[Cu/Zn‐MOF]) has been synthesized by immersing the CoFe₂O₄/Zn‐TMU‐17‐NH₂ (CoFe₂O₄/Zn‐MOF) as a template in DMF solution of Cu (II) salts. CoFe₂O₄/[Cu/Zn‐MOF] showed to be a highly reactive and easily recoverable magnetic catalyst for the preparation of tetrazole derivatives via one‐pot three‐component reactions of different aldehydes with hydroxyl amine hydrochloride and sodium azide. Our results (Fourier transform‐infrared, inductively coupled plasma‐optical emission spectroscopy, powder X‐ray diffraction, field emission‐scanning electron microscopy, energy‐dispersive X‐ray spectroscopy‐mapping and vibrating‐sample magnetometer) show successful partial metal‐exchange in which the framework integrity remained intact during the metal‐exchange process.