Surface modification of MWCNTs with glucose and their utilization for the production of environmentally friendly nanocomposites using biodegradable poly(amide‐imide) based on N‐trimellitylimido‐S‐valine matrix

In the present investigation, the preparation, characterization, and surface morphology of poly(amide‐imide) (PAI)/multi‐walled carbon nanotubes (MWCNTs) bionanocomposites (BNCs) were the main goals of the study. At first, an optically active PAI based on S‐valine as a biodegradable segment was synthesized. Then, carboxyl‐modified MWCNTs were functionalized with glucose (f‐MWCNT) as a biological active molecule in a green method to achieve a fine dispersion of f‐MWCNT bundles in the PAI matrix. The existence of S‐valine in the PAI matrix and functionalized MWCNT with glucose resulted in a series of potentially biodegradable nanocomposites. The obtained BNCs were characterized by various techniques. Field emission scanning and transmission electron microscopy micrographs of the composites showed a fine dispersion of f‐MWCNTs in the polymer matrix because of hydrogen bonding and π–π stacking interaction between f‐MWCNTs and polymer functional groups and aromatic moieties. Adding f‐MWCNTs into polymer matrix significantly improved the thermal stability of BNCs because of the increased interfacial interaction between the PAI matrix and f‐MWCNTs and also good dispersion of f‐MWCNT in the polymer matrix. Copyright © 2015 John Wiley & Sons, Ltd.     

Polymerized ionic liquid functionalized multi-walled carbon nanotubes/polyetherimide composites

Thin polyetherimide (PEI) films containing 0.1–3 wt.% multi-walled carbon nanotubes (MWCNTs), have been prepared from three types of MWCNTs, namely pristine, oxidized and polymerized ionic liquid (PIL) functionalized CNTs. Oxidized and PIL functionalized CNTs (CNT–PIL) showed better dispersion in the matrix compared to pristine CNTs. For CNT–PIL, alignment of CNTs has been observed in the matrix. Regardless of the type of CNTs, their incorporation led to an increased thermal stability of the polymer matrix. Dynamic mechanical analysis showed that storage modulus increased by up to 25% (3 wt.% CNT–PIL) and an increase in the height of the damping peaks (tan δ). The addition of CNTs did not have any significant influence on the tensile properties and T_g of the polymer, and the electrical conductivity did not decrease in the case of modified CNTs.     

The effects of reactive organoclay on the thermal, mechanical, and microstructural properties of polymer/layered silicate nanocomposites based on chiral poly(amide-imide)s

Considering the importance of the nanocomposites, the present work focuses on some new hybrid materials prepared by introducing reactive organoclay (OC) into the chiral poly(amide-imide) (PAI) matrix. At first, Cloisite Na⁺ was modified with protonated l-isoleucine amino acid. Then, PAI containing phenylalanine was synthesized via solution polycondensation of chiral diacid chloride with 4,4′-diaminodiphenylsulfone and was characterized with Fourier transform infrared (FTIR) and ¹H NMR techniques. At last, PAI/OC nanocomposite films containing 2, 5, 10, and 15 % of OC were prepared via solution intercalation method. The effect of OC dispersion and the interaction between OC and polymer chains on the properties of nanocomposites were investigated using FTIR, X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy, tensile testing of thin films, and thermogravimetry analysis techniques. The thermal stability of hybrids such as the decomposition temperature and mass residue at 800 °C was improved. Mechanical data indicated improvement in the tensile strength of the nanocomposites with OC loading up to 10 wt%. The transparency of the hybrid films was investigated by means of UV–Vis spectra.     

Chiral poly(amide-imide)/organoclay nanocomposites derived from pyromellitoyl-bis-l-isoleucine and benzimidazole containing diamine: synthesis, nanostructure, and properties

In this study, a series of polymer–clay nanocomposite materials, consisting of organosoluble poly(amide-imide) (PAI) matrix and dispersed nanolayers of inorganic montmorillonite clay, were successfully prepared by solution dispersion technique. At first, the reactive organoclay was prepared by using protonated l-isoleucine amino acid as a swelling agent for silicate layers of Cloisite Na⁺. Then, organosoluble PAI containing isoleucine amino acid was synthesized through step-growth polymerization reaction of N,N′-(pyromellitoyl)-bis-isoleucine diacid and 2-(3,5-diaminophenyl)-benzimidazole under green condition using molten tetrabutylammonium bromide. This polymer was end-capped with amine end groups near the completion of the reaction to interact chemically with acidic group of organoclay. Finally, PAI/organoclay nanocomposite films containing 2%, 5%, 10%, and 15% of organoclay were prepared via solution intercalation method through blending of organoclay with the PAI solution. Dispersion of the modified clay in the PAI matrix resulted in a nanostructured material containing intercalated polymer between the silicate layers. Structures of exfoliation were confirmed by X-ray diffraction, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, and transmission electron microscopy. Thermogravimetric analysis data indicated that the addition of organoclay into the PAI matrix increased the thermal decomposition temperatures of the obtained nanocomposites compared to the pure PAI.     

Influence of MWCNT morphology on dispersion and thermal properties of polyethylene nanocomposites

In this study a series of multi-walled carbon nanotube (MWCNT)/Polyethylene (PE) composites with different kinds and several concentrations of carbon nanotubes (CNTs) were investigated. The morphology and degree of dispersion of the fillers in the polymer matrix at different length scales was investigated using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Both individual and agglomerated MWCNTs were evident but a good dispersion was observed for some of them. TGA measurements were performed on nanocomposites in order to understand if CNTs affect the stabilization mechanism during thermal and oxidative degradation. The analysis demonstrates that MWCNTs presence slightly delays thermal volatilisation (15-20 °C) without modification of thermal degradation mechanism. In contrast, thermal oxidative degradation in air is delayed up to about 100 °C dependently from MWCNTs concentration, in the range used here (0.1-2.0 wt%), and degree of dispersion. The stabilization is due to the formation of a thin protective layer of entangled MWCNTs kept together by carbon char generated on the surface of the nanocomposites as shown by SEM images taken on degradation residues.     

Improving Thermal and Flame Retardant Properties of Epoxy Resin with Organic NiFe‐Layered Double Hydroxide‐Carbon Nanotubes Hybrids

To improve the dispersion of carbon nanotubes (CNTs) and flame retardancy of layered double hydroxide (LDH) in epoxy resin (EP), organic nickel‐iron layered double hydroxide (ONiFe‐LDH‐CNTs) hybrids were assembled through co‐precipitation. These hybrids were further used as reinforcing filler in EP. EP/ONiFe‐LDH‐CNTs nanocomposites containing 4 wt% of ONiFe‐LDH‐CNTs with different ratios of ONiFe‐LDH and CNTs were prepared by ultrasonic dispersion and program temperature curing. The structure and morphology of the obtained hybrids were characterized by different techniques. The dispersion of nanofillers in the EP matrix was observed by transmission electron microscopy (TEM). The results revealed a coexistence of exfoliated and intercalated ONiFe‐LDH‐ CNTs in polymer matrix. Strong combination of the above nanofillers with the EP matrix provided an efficient thermal and flame retardant improvement for the nanocomposites. It showed that EP/ONiFe‐LDH‐CNTs nanocomposites exhibited superior flame retardant and thermal properties compared with EP. Such improved thermal properties could be attributed to the better homogeneous dispersion, stronger interfacial interaction, excellent charring performance of ONiFe‐LDH and synergistic effect between ONiFe‐LDH and CNTs.     

Influence of imide functionalized organo‐modified Mg‐Al layered double hydroxide on the thermal and mechanical properties of new aliphatic‐aromatic poly (amide‐imide)

A new dicarboxylic acid modified Mg‐Al LDH (DLDH) containing imide groups was prepared and its effects on the thermal and mechanical properties of the new synthesized aliphatic‐aromatic poly (amide‐imide) (PAI) were investigated via preparation of PAI/nanocomposite films by solution casting method. The results of X‐ray diffraction (XRD), field emission‐scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM) showed a uniform dispersion for LDH layers into the PAI matrix. For comparison, the effects of polyacrylic acid‐co‐poly‐2‐acrylamido‐ 2‐methylpropanesulfonic acid (PAMPS‐co‐PAA) modified Mg‐Al LDH (ALDH) on the PAI properties were also studied. The thermogravimetric analysis (TGA) results exhibited that the temperature at 5 mass% loss (T₅) increased from 277 °C to 310 °C for nanocomposite containing 2 mass% of DLDH, while T₅ for nanocomposite containing 2 mass% of ALDH increased to 320 °C, along with the more enhancement of char residue compared to the neat PAI. According to the tensile test results, with 5 mass% DLDH loading in the PAI matrix, the tensile strength increased from 51.6 to 70.8 MPa along with an increase in Young's modulus. Also the Young's modulus of PAI nanocomposite containing 5 mass% ALDH reduced from 1.95 to 0.81 GPa.     

Contribution of oriented structure and rigid nanofillers to mechanical enhancement of die-drawn PP/MWCNT composites

Oriented structure, mainly controlled by processing conditions, is another efficient method of reinforcing polymer materials in addition to compounding with rigid inorganic fillers such as carbon nanotubes (CNTs). The mechanical properties of oriented polypropylene (PP)/multiwalled CNT (MWCNT) composites, which are vital to their application fields, are investigated extensively in this paper, with an aim to distinguish the contribution of MWCNTs contents from that of the oriented structure to the final performance of the composite. The results indicate that MWCNTs mainly increase the modulus of the composites by approximately 140%. The oriented structure formed during the die-drawing process contributes more to the enhancement of tensile strength, increasing up to 550%. The modulus and tensile strength can be further improved by increasing the drawing speed. Moreover, the tensile stress field in the die-drawing process can vastly improve the dispersion of the MWCNTs in the matrix, thus providing a new idea for improving the dispersion of nanofillers in the polymer matrix.     

碳纳米管改性聚苯硫醚熔纺纤维的结构与性能研究

将多壁碳纳米管(MWCNTs)和聚苯硫醚(PPS)经过熔融挤出后制备成复合材料切片,并采用熔融纺丝法制得碳纳米管改性聚苯硫醚复合纤维.采用扫描电镜(SEM)、拉曼光谱、示差扫描量热分析(DSC)、动态机械分析(DMA)以及力学性能测试等表征手段研究了复合纤维中碳管的分散状态,与基体的界面作用,复合纤维的结晶性能以及力学性能,从而探讨了聚苯硫醚/碳纳米管复合纤维体系的微观结构与宏观性能之间的关系.研究表明,聚苯硫醚分子结构与碳纳米管之间具有的π-π共轭作用使碳管较为均匀的分散在基体中,界面结合较为紧密.同时熔融纺丝过程中的拉伸作用使碳管进一步解缠并使碳管沿纤维拉伸方向取向.另一方面,拉曼光谱显示拉伸作用有效地增强了界面作用,有利于外界应力的传递.碳管的良好分散以及强的界面作用使复合纤维力学性能得到大幅度的提高,当碳管含量达到5 wt%时,复合纤维的模量有了明显的提高,拉伸强度较纯PPS纤维提高了近220%.     

Nanotubes as polymer composite reinforcing additive materials – A comparative study

Nitrogen-doped bamboo-shaped carbon nanotubes (N-BCNTs) and their non-doped conventional counterparts, multiwalled carbon nanotubes (MWCNTs) were compared as polymer reinforcing additives in polyvinyl chloride (PVC) matrix. The nanotubes were synthetized by catalytic chemical vapor deposition (CCVD) method. The purity of both nanotubes was measured by thermogravimetric analysis (TGA) and found to be >91%. Further analysis on the morphology and size of the carbon nanotubes (CNTs) were performed by transmission electron microscopy (TEM). The PVC powder was impregnated with CNTs in ethanol by using tip ultrasonicator. The dispersion media was evaporated, and the CNT/PVC powder was used to produce polymer fibers. The orientation of carbon nanotubes in the PVC matrix was characterized by scanning electron microscopy (SEM), and the presence of nanotubes were confirmed in case of all PVC samples. It can be observed on the SEM images that the nanotubes are fully covered with PVC. The tensile strength of the nanotube containing samples was tested and the N-BCNT/PVC composite was found to be better in this sense, thanks to the extraordinary structure of the nanotube. In case of the N-BCNT/PVC composite the measured young modulus was 39.7% higher, while the elongation at brake decreased by 33.6% compare to the MWCNT/PVC composite. These significant differences in the mechanical properties of the composites can be explained with the stronger interaction between N-BCNTs and PVC.     

Dissolution of MWCNTs by using polyoxadiazoles,and highly effective reinforcement of their composite films

Nonmodified multiwalled carbon nanotubes (MWCNTs)/sulfonated polyoxadiazole (sPOD) nanocomposites are successfully prepared by a facile solution route. The pristine MWCNTs are dispersed in a sPOD solution, and the mixtures are fabricated into thin films by solution casting. The homogeneous dispersion of nanotubes in the composites is confirmed by transmission electron microscopy. The mechanical properties, thermal stability, and electrical conductivity are investigated. Tensile strength, elongation at break, and tensile energy to break are shown to increase by more than 28, 45, and 73%, respectively, by incorporating up to 1.0 wt % pristine MWCNTs. The experimental values for sPOD/MWCNTs composite stiffness are compared with Halpin‐Tsai and modified Halpin‐Tsai predictions. The storage modulus is found to increase up to 10% at low CNT loading. The composite films, which have an outstanding thermal stability, show an increase of up to 57 °C in the initial degradation temperature. The addition of 1.0 wt % MWCNTs increases the electrical conductivity of the sPOD matrix by two orders of magnitude. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Influence of hybrid system of nanofillers on the functional properties of postconsumer PET‐G–based nanocomposites

In this article, postconsumer poly (ethylene glycol‐co‐1,4‐cyclohexanedimethanol terephthalate) (PET‐G) foils have been modified with three types of carbon nanofillers that differ in size and shape, ie, multiwalled carbon nanotubes (MWCNTs), graphene nanoplatelets (GNP), and nanosized carbon black (nCB), thus enabling the reusage of recyclate in receiving new functional materials. The series of polymer hybrid nanocomposites have been prepared via a two‐stage polycondensation process, be means of glycolysis of postconsumer PET‐G foil, followed by polycondensation in the presence of carbon nanofillers. The scanning electron microscopy revealed that nanoadditives were uniformly dispersed into the whole volume of polymer matrix. The results present the synergistic effect of hybrid system of nanofillers in improving tensile properties of PET‐G. It has been found that the incorporation of three types of carbon nanofillers has not affected the glass transition temperature of the polymer matrix. Moreover, the incorporation of carbon nanofillers, and the mixture of two, or even three of those, caused an improvement in thermal conductivity and thermal stability.     

Surfactant dispersed multi-walled carbon nanotube/polyetherimide nanocomposite membrane

Carbon nanotube based nanocomposite membranes have been fabricated through solution casting by embedding multi-walled carbon nanotubes (MWCNTs) within polyetherimide (PEI) polymer host matrix. In order to achieve fine dispersion of nanotubes and facilitate strong interfacial adhesion with the polymer matrix, the nanotubes were first treated with surfactants of different charges, namely anionic sodium dodecyl chloride, cationic cetyl trimethyl ammonium chloride and non-ionic Triton X100, prior to the dispersion in the PEI dope solution. Dispersion of MWCNTs in N-methyl-2-pyrrolidone solvent showed that the agglomeration and entanglement of the nanotubes were greatly reduced upon the addition of Triton X100. Scanning electron microscopy and atomic force microscopy examination has evidenced the compatibility of Triton X100 dispersed MWCNTs with the polymer matrix in which a promising dispersion and adhesion has been observed at the MWCNT-PEI interface. The increase in both thermal stability and mechanical strength of the resulting Triton X100 dispersed MWCNT/PEI nanocomposite indicated the improved interaction between MWCNTs and PEI. This study demonstrated the role of Triton X100 in facilitating the synergetic effects of MWCNTs and PEI where the resulting composite membrane is anticipated to have potential application in membrane based gas separation.     

掺杂羧基化碳纳米管的纳米碳纤维前驱体的制备及表征

为获得结构完整、 性能优良的纳米碳纤维前驱体, 采用静电纺丝法制备了掺杂羧基化多壁碳纳米管(MWCNTs)的聚丙烯腈(PAN)纳米纤维. 用扫描电子显微镜、 偏振红外光谱、 透射电子显微镜、 拉曼光谱及拉伸性能测试等对杂化纳米纤维的微观结构和力学性能进行了研究, 分析了MWCNTs含量的影响. 实验结果表明, 5%(质量分数)的MWCNTs掺杂量为杂化纳米纤维直径的突变点, 且MWCNTs的加入有利于PAN分子链的取向, MWCNTs在PAN纤维中大体上沿纤维轴向取向分布. 3%MWCNTs/PAN杂化纳米纤维的拉伸强度和拉伸模量分别达到88.6 MPa和3.21 GPa.     

Synthesis,stereocomplex crystallization and properties of poly(l‐lactide)/four‐armed star poly(d‐lactide) functionalized carbon nanotubes nanocomposites

Functionalized carbon nanotubes (F‐CNTs) were synthesized through the nucleophilic substitution reaction between four‐armed star poly(d ‐lactide) (4PDLA) and acryl chloride of carbon nanotubes and were characterized using Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy and thermogravimetric analysis. The results indicated that the 4PDLA was successfully grafted onto carbon nanotubes, and it contained 45.5 wt% of 4PDLA. Poly(l ‐lactide) (PLLA) nanocomposites with different F‐CNTs content were prepared by solution casting. Optical microscopy and scanning electron microscopy results showed that F‐CNTs were uniformly dispersed in the nanocomposites. Crystallization behavior and crystal structure of PLLA nanocomposites were investigated using differential scanning calorimetry, polarizing microscope and X‐ray diffraction. The results found that poly(lactide) stereocomplex crystal could be formed between PLLA and F‐CNTs. F‐CNTs played different roles in the process of solution casting and melting crystallization. Polarizing microscope also revealed that crystallization temperature had a significant effect on the nucleation and spherulites growth of PLLA. Thermal stability and mechanical properties of the nanocomposites were also investigated by thermogravimetric analysis, dynamic mechanical analysis and tensile testing. These results demonstrated that the addition of F‐CNTs obviously improved thermal stability and tensile strength of PLLA. The results showed that PLLA/F‐CNTs would have potential values in engineering fields. Copyright © 2015 John Wiley & Sons, Ltd.     

Crystallization Behavior and Mechanical Properties of Poly(vinylidene fluoride)/multi-walled Carbon Nanotube Nanocomposites

Poly(vinylidene fluoride)(PVDF)/multi-walled carbon nanotube(MWCNT) nanocomposites were prepared by means of ultrasonic dispersion method. X-ray diffraction(XRD) results indicate that incorporating MWCNTs into PVDF caused the formation of β phase. A thermal annealing at 130 °C confirmed that the β phase was stable in the nanocomposites. Differential scanning calorimetry(DSC) results indicate that the melting temperature slightly increased while the heat of fusion markedly decreased with increasing MWCNT content. The tensile strength and modulus of PVDF were improved by loading the MWCNTs. The scanning electron microscopy(SEM) observations showed that MWCNTs were uniformly dispersed in the PVDF matrix and an interfacial adhesion between MWCNT and PVDF was achieved, which was responsible for the enhancement in the tensile strength and modulus of PVDF.     

Preparation and properties of poly(vinyl alcohol)/silica nanocomposites derived from copolymerization of vinyl silica nanoparticles and vinyl acetate

Nanocomposites of poly(vinyl alcohol)/silica nanoparticles (PVA-SNs) were prepared by in-situ radical copolymerization of vinyl silica nanoparticles functionalized by vinyltriethoxysilane (VTEOS) and vinyl acetate with benzoyl peroxide (BPO, i.e., initiator), subsequently saponified via direct hydrolysis with NaOH solution. The resulting vinyl silica nanoparticles, PVA-SNs were characterized by means of fourier transformation spectroscopy (FTIR), transmission electron microscopy (TEM) and the elemental analysis method. Effects of silica nanoparticles on viscosity and alcoholysis of PVA-SNs were studied by a ubbelohode capillary viscometer and the back titration method. The morphological structure of PVA-SN films was investigated by scanning electron microscopy (SEM). Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and tensile test were used to determine the thermal and mechanical properties of PVA-SN films. The results indicated that the content of vinyl groups on the surface of the vinyl silica nanoparticles was up to 3.02 mmol/g and vinyl silica nanoparticles had been successfully copolymerized with vinyl acetate. Furthermore, compared to pure PVA, silica nanoparticles bonded with polymer matrix in a low concentration affected the viscosity and alcoholysis of the PVA-SNs materials. At the same time, it resulted in the improvement of the thermal and mechanical properties of the PVA-SN materials due to a strong interaction between silica nanoparticles and the polymer matrix via a covalent bond. It could be found that the optical clarity of the membrane was changed through UV-Vis absorption spectrum due to the introduction of silica nanoparticles.     

Effect of the melt flow index of an HDPE matrix on the properties of composites with wood particles

Composites of wood waste and high-density polyethylene (HDPE) resins and different melt flow index (MFIs) was development in this work. Therefore, it was possible to assess their effect on the mechanical, thermal, and morphologic properties of these composites. The formulations were prepared using a twin-screw extruder, and the MFI, tensile strength, flexural strength, and impact strength of the composites were analyzed. Additionally, the thermal properties were evaluated by differential scanning calorimetry (DSC). Finally, structural analyses using optical microscopy (OM) and scanning electron microscopy (SEM) were performed to assess the particles’ dispersion, distribution, and adhesion to the polymer matrix. The results indicated that composites from HDPE resins with a lower MFI yielded a better dispersion of the wood waste. During processing was observed, reduce the MFI and better dispersion of the polymer matrix, which positively influenced some of the mechanical properties analyzed in the study.     

Effects of pH on mechanical and morphological studies of silica filled polyvinyl chloride-50% epoxidized natural rubber (PVC-ENR50) nanocomposite

Effects of pH on mechanical properties as well as morphological studies of sol–gel derived in situ silica in polyvinyl chloride-50% epoxidized natural rubber (PVC-ENR50) nanocomposites are reported. In particular, a range of acid concentrations was investigated. These nanocomposites were prepared by solution casting technique and tetraethoxysilane (TEOS) was used as the silica precursor. The prepared nanocomposites were characterized using tensile test, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The tensile test indicated that the highest mechanical strength was at 30% TEOS added for the nanocomposite prepared at pH 2.0. At pH 1.0 and 1.5 the maximum tensile strength reading was at 20% TEOS added with value of 24.3 and 24.5 MPa, respectively. SEM and TEM revealed the dispersion of silica particles in the polymer matrix. For nanocomposites prepared at pH 1.0 and 1.5, the silica particles were finely dispersed with the average size of 60 nm until 20% TEOS added. Meanwhile for nanocomposite prepared at pH 2.0, silica particles were homogenously distributed in the polymer matrix with average diameter of 30 nm until 30% TEOS and agglomerated after 30% TEOS loading.     

Preparation and characterization of poly(amide-imide)/ZnO nanocomposites containing pendent benzoxazole and benzimidazole segments

In the present investigation, novel poly(amid-imide)/zinc oxide nanocomposites (PAI/ZnO NCs) containing benzoxazole and benzimidazole pendent groups with different amounts of modified zinc oxide nanoparticles (ZnO NPs) were successfully prepared via the ex situ method. Poly(amid-imide) (PAI) was prepared by direct polycondensation of 2-[3,5- bis(N-trimellitimidoyl)phenyl]benzoxazole (DCA) with 5-(2-benzimidazole)-1,3-phenylenediamine (DAMI) and provided the polymeric matrix with well-designed groups. The surface of ZnO NPs was functionalized with 3-aminopropyltriethoxysilane (APS) coupling agent to have a better dispersion and enhancing possible interactions of NPs with functional groups of polymer matrix. The amount of APS bonded to the ZnO surface was determined by thermogravimetric analysis. PAI/ZnO nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM). SEM analysis showed that the modified ZnO nanoparticles were homogeneously dispersed in polymer matrix. In addition, TGA data indicated an enhancement of thermal stability of the nanocomposite compared with the neat polymer.