Effect of alcohols on the gamma-radiation-induced polymerization of ethylene

Gamma-radiation-induced polymerization of ethylene in alcohols such as methyl, ethyl, n-propyl, isopropyl, n-butyl, isobutyl, sec-butyl, tert-butyl, and n-pentyl alcohols was carried out under a pressure of 400 kg./cm.²at 30°C. at a dose rate of 1.4 × 10⁵ rad/hr. in a batch reactor of 100 ml. capacity. The yield and molecular weight of polymer formed in the alcohols (except tert-butyl alcohol) were much lower than those of the bulk polymerization under the same conditions, whereas the addition of tert-butyl alcohol increased the yield and reduced the molecular weight. From the infrared spectra of the polymers and those of the bromination products it was concluded that only primary OH exists in the polymer formed in methyl alcohol and that both primary and secondary OH are in the polymer formed in other primary alcohols. Both secondary and tertiary OH were observed in the polymer when the secondary alcohols were used, and only tertiary OH in the case of tert-butyl alcohol. These polymers were found to contain small amounts of vinylidene unsaturation and methyl group. On the basis of these results the roles of the alcohols in the polymerization are discussed.     

Elementary reaction and anionic polymerization of isopropenly t-butyl ketone

Isopropenyl t-butyl ketone (IPTBK) does not undergo radical homopolymerization and its anionic polymerization is a slow equilibrium process with a low ceiling temperature, which is due to its limited conjugation imposed by steric hindrance. Equimolar reactions of IPTBK with several anionic initiators were carried out, products isolated and identified by ¹H-and ¹³C-NMR, and product distributions determined by GC. While n-butyllithium and phenyllithium preferentially produce allyl alcohols, Grignard reagents predominantly undergo β-addition to produce mono-adducts, and a significant amount of dimers. t-Butyllithium and t-butylmagnesium chloride provide the cleanest β-addition with minimal dimer formation and no carbonyl addition. However, Grignard reagent do not yield a polymer. The 1:1 reaction mixture of IPTBK with t-butyllithium is very stable at 0°C, providing a methyl-terminated mono-adduct quantitatively when quenched with methyl iodide after 29 h. Addition of a second IPTBK to the mono-adduct anion appears to be affected by the low ceiling temperature. Although t-butyllithium can efficiently reduce as well as add to di-t-butyl ketone, such reactions are minor in the presence of IPTBK. Anionic polymerization of IPTBK with t-butyllithium was carried out under several conditions. The 1:1 model reactions and the lack of acidic hydrogens in its structure suggest that anionic polymerization of IPTBK with t-butyllithium may be “living.” The molecular weight distribution of the polymers ranged from 1.1 to 1.6 with the number-average molecular weight varying from 2,800 to 233,500. Group transfer polymerization of IPTBK produced only a six-membered lactone.     

Role of chain transfer in heterogeneous polymerization of ethylene

The role of chain transfer was studied for the radiation-induced polymerization of ethylene in precipitating media, namely n-butyl alcohol, tert-butyl alcohol and their mixtures. The affinities of those solvents for polyethylene are similar, but the chain-transfer coefficient of n-butyl alcohol is larger than that of tert-butyl alcohol. The polymerizations were carried out in a reactor of 100 ml under a pressure of 300 kg/cm², at 60°C, dose rate of 3.07 × 10⁴–1.75 × 10⁵ rad/hr in the presence of 50 ml of solvents. The polymerization in tert-butyl alcohol shows the kinetic behavior characteristic of a heterogeneous polymerization, such as rate acceleration, high dose rate dependence of polymerization rate, and low dose rate dependence of polymer molecular weight, whereas the polymerization in n-butyl alcohol does not exhibit such behavior and gives polymer having a molecular weight much lower than that of polymer obtained in tert-butyl alcohol. The polymer formed in tert-butyl alcohol exhibits a bimodal molecular weight distribution measured by gel permeation chromatography. In mixed tert-butyl alcohol and n-butyl alcohol solvent, with increasing fraction of n-butyl alcohol, the two peaks not only shift to lower molecular weight but the higher molecular weight peak becomes relatively small. Eventually, the polymer formed in n-butyl alcohol exhibits a unimodal distribution. Those results are well explained on the basis of the proposed scheme for heterogeneous polymerization.     

Influence of the alkyl group of triflate esters on their initiation ability for the cationic ring-opening polymerization of tetrahydrofuran

Esters of trifluoromethane sulfonic acid have been synthesized by reaction of different alcohols with triflic anhydride and used in situ as initiators for the polymerization of tetrahydrofuran. Kinetic studies of the polymerization showed that allyl triflate has the highest reactivity and that an increase of the alkyl chain length of the initiator leads to a significant decrease of the initiation rate. “Non-linear” triflate ester such as isobutyl triflate leads to incomplete initiation. It was impossible to synthesize quantitatively the triflate from tert-butyl alcohol due to spontaneous elimination leading to isobutylene.     

Effect of temperature on the radiation-induced polymerization of ethylene in various media

The effects of temperature on the radiation-induced polymerization of ethylene in bulk and in the presence of ethyl alcohol, n-butyl alcohol, tert-butyl alcohol, cyclohexane, 2,2,4-trimethylpentane, and 2,2,5-trimethylhexane were studied. The changes of the amounts of polymerized monomer with the reaction temperature were different from each other in these reaction systems, especially in the range lower than 60–80°C. At temperatures lower than 60–80°C, as the reaction temperature increases, the amount of polymerized monomer decreased in bulk and in the presence of tert-butyl alcohol. The amount was almost constant in the presence of ethyl alcohol and 2,2,4-trimethylpentane, and it increased in the presence of n-butyl alcohol, cyclohexane, and 2,2,5-trimethylhexane. However, in the temperature range higher than 60–80°C, the amount of polymerized monomer increased with increasing temperature in every reaction system except for bulk polymerization. The molecular weight of polymer decreased with increasing temperature in every reaction system except at temperatures lower than 25°C. The molecular weight of polymer formed in bulk, in tert-butyl alcohol, and also in 2,2,4-trimethylpentane were relatively higher than that in other reaction systems. A bimodal molecular weight distribution was observed for the polymer formed in bulk and in tert-butyl alcohol at 40–60°C. These results are discussed in connection with the heterogeneity of the reaction system. The differences due to temperature in each reaction system are explained as due to the difference in affinity of the reaction system for the propagating chain and in the facility of chain transfer to the medium.     

Cationic polymerization of α,β-disubstituted olefins. Part II. Cationic polymerization of propenyl N-butyl ether

The cationic polymerization of propenyl n-butyl ether (PBE) in methylene chloride with boron fluoride etherate at ?78°C. has been studied. The copolymerization of PBE with vinyl n-butyl ether (VBE) showed that both the isomers are more reactive than VBE, and their monomer reactivity ratios were found to be:     

Radiation-induced emulsion polymerization of ethylene. IV. Effect of pressure,temperature, and additives on rate in connection with number of polymer particles

The effects of pressure, temperature, and additives on the rate of radiation-induced emulsion polymerization of ethylene with FC-143 as emulsifier were studied kinetically. The rate of polymerization was proportional to the 2.5 power of ethylene fugacity, and the apparent rate constant (rate of polymerization/2.5 power of ethylene fugacity) was constant below 78°C. Above this temperature, the rate constant decreased with an apparent activation energy of ?8.2 kcal/mole. These facts can be interpreted in connection with the polymer structure and the change of rate of escape of radicals from the polymer structure and the change of rate of escape of radicals from the polymer particle into the aqueous phase. The rate of polymerization decreased on addition of a series of n-aliphatic alcohols due to the chain-transfer reaction and consequent escape of radicals to the aqueous phase. On the other hand, the addition of tert-butyl alcohol increased the rate of polymerization, probably because of its effect in increasing swelling of the polymer particles. Addition of electrolytes increased the rate of polymeriaztion as a result of the increase of the number of polymer particles.     

Kinetic studies on the n-alkyl acrylate polymerization

Kinetic studies on the polymerization of n-butyl acrylate and n-octadecyl acrylate in toluene at 70°C with benzoyl peroxide as initiator are reported. High monomer orders of 1.55 and 1.75 were obtained for n-butyl and n-octadecyl acrylates, respectively. Though the initiator order in butyl acrylate polymerization was 0.5, the octadecyl acrylate polymerization showed less than square root initiator order. The activation energy for the polymerization of both the acrylates was determined. Autoacceleration was found even at low conversions. The autoacceleration was influenced by both monomer and initiator concentration. Molecular weight data was presented in support of the gel effect. © 1992 John Wiley & Sons, Inc.     

Kinetics of styrene homogeneous polymerization to atactic polypropylene

The rate of polymerization of styrene initiated by hydroperoxidized atactic polypropylene in a homogeneous toluene solution has been measured at 60 and 70°C. The reaction is first-order with respect to styrene concentration and independent of the polymeric hydroperoxide concentration above 2 × 10^?5N hydroperoxide. The individual rate constants, length and frequency of the grafted polystyrene chains along the polypropylene backbone have been calculated and their significance discussed. The initiation rate constant compares closely with values reported for the analogous tert-butyl hydroperoxide-initiated polymerization. The rate constant for the chain transfer termination elementary step at 70°C., however, is 18 times the value reported for the tert-butyl hydroperoxide-initiated polymerization of styrene. This high constant accounts for the relatively low rates of polymerization observed and high termination rates. Chain deactivation is presumably accelerated by increased collisions between growing styrene chains and inactive propylene hydroperoxide and polystyrene molecules. Distribution of polystyrene grafts on polypropylene is estimated from knowledge of effects of styrene concentration, polymeric hydroperoxide concentration, and temperature upon the rate of polymerization.     

Functionally Substituted Amides and Esters of 3,4,4-Trichloro-3-butenoic Acid

Substituted amides and esters of 3,4,4-trichloro-3-butenoic acid were prepared by reactions of its chloride with appropriate amines and alcohols. Treatment of 3,4,4-trichloro-3-butenomorpholide and tert-butyl 3,4,4-trichloro-3-butenoate results in nucleophilic substitution of the internal chlorine atom with the morpholine residue, accompanied by prototropic allyl rearrangement.     

Fine structure of polyethylene prepared by γ-ray-induced polymerization in various solvents. III. Selective degradation with ozone

Ozone-degradation products of polyethylenes prepared by γ-ray-Induced polymerization in ethyl alcohol, t-butyl alcohol, and 2,2,5-trimethylhexane were analyzed by gel permeation chromatography (GPC). The ozonized polymers show two discrete peaks in the GPC traces, and the ratio of molecular weights corresponding to the peaks is close to 1:2, suggesting that these polymers are composed of folded-chain crystals similar to solution-grown single crystals. The peak profiles, however, are broad and the peaks in the chromatograms shift concertedly toward lower molecular weight in the course of degradation. These findings suggest that the fold surfaces of the polymers are coarse and that there is no unique crystalline core containing a regularly folded layer. The long period estimated from small-angle x-ray measurements increases with increasing polymerization temperature, but scarcely varies with the solvent type. This implies that when crystallization occurs during polymerization, kinetic factors may have no great effect on crystallization.     

Lactone polymers. VIII. Dynamic mechanical properties of ϵ-caprolactone and γ-(tert-butyl)-ϵ-caprolactone copolymers

The temperature dependencies of dynamic mechanical properties have been determined with a torsional pendulum for copolymers of ?-caprolactone and γ-(tert-butyl)-?-caprolactone over the entire composition range. Copolymers containing at least 25 mol % (33 wt %) of γ-(tert-butyl)-?-caprolactone units are amorphous in nature. The experimentally obtained glass transition temperatures of the copolymers and poly(γ-(tert-butyl)-?-caprolactone) were used to calculate the glass transition temperature of amorphous of poly(?-caprolactone) according to the Fox relation. This value of ?70°C is in excellent agreement with values obtained from similar calculations based on compatible blends of poly(?-caprolactone) with other homopolymers.     

Syndiotactic‐ and heterotactic‐specific radical polymerizations of N‐n‐propyl‐α‐fluoroacrylamide and phase‐transition behaviors of aqueous solutions of poly(N‐n‐propyl‐α‐fluoroacrylamide)

Radical polymerization of N‐n‐propyl‐α‐fluoroacrylamide (NNPFAAm) was investigated in several solvents at low temperatures in the presence or absence of Lewis bases, Lewis acids, alkyl alcohols, silyl alcohols, or fluorinated alcohols. Different effects of solvents and additives on stereospecificity were observed in the radical polymerizations of NNPFAAm and its hydrocarbon analogs such as N‐isopropylacrylamide (NIPAAm) and N‐n‐propylacrylamide (NNPAAm); for instance, syndiotactic (and heterotactic) specificities were induced in radical polymerization of NNPFAAm in polar solvents (and in toluene in the presence of alkyl and silyl alcohols), whereas isotactic (and syndiotactic) specificities were induced in radical polymerizations of the hydrocarbon analogs under the corresponding conditions. In contrast, heterotactic specificity induced by fluorinated alcohols was further enhanced in radical polymerization of NNPFAAm. The effects of stereoregularity on the phase‐transition behaviors of aqueous solutions of poly(NNPFAAm) were also investigated. Different tendencies in stereoregularity were observed in aqueous solutions of poly(NNPFAAm)s from those in solutions of the hydrocarbon analogs such as poly(NIPAAm) and poly (NNPAAm). The polymerization behavior of NNPFAAm and the phase‐transition behavior of aqueous poly(NNPFAAm) are discussed based on possible fluorine–fluorine repulsion between the monomer and propagating chain‐end, and neighboring monomeric units. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

A new microwave dielectric method for studying photoinitiated chain radical polymerization processes

Measurements of both real and imaginary parts of the dielectric constant at a fixed microwave frequency have been performed on n-butyl acrylate/poly(n-butyl acrylate) mixtures. The dielectric constant of the mixtures has been compared with that of neat n-butyl acrylate during UV photoinitiated polymerization. The values of the imaginary part of the dielectric constant thus obtained have allowed determination of the instantaneous monomer concentration and verified the kinetic equation for the photoinitiated polymerization process. The limits of validity of the method as well as its capability of providing detailed kinetic information are also discussed.     

Influence of the swelling state of seed polymer particles with monomer on the morphology of micron-sized monodispersed composite polymer particles produced by seeded polymerization utilizing the dynamic swelling method

 Micron-sized mono-dispersed polystyrene (PS)/poly(n-butyl methacrylate) (PBMA) composite particles (PS/PBMA=2/1 by weight) having a heterogeneous structure in which many fine PBMA domains dispersed in a PS matrix near the particle surface were produced by seeded polymerization of n-butyl methacrylate (BMA) of which almost all had been absorbed by 1.8 μm-sized monodispersed PS seed particles utilizing the dynamic swelling method. The morphology was varied by changing the PS/BMA ratio and polymerization temperature. It was concluded that the swelling state of 2 μm-sized BMA-swollen PS particles in the seeded polymerization process is one of the important factors to control the morphology of the composite particles. Received: 27 November 1996 Accepted: 21 March 1997     

Preparation and radical ring-opening polymerization of exo-methylene substituted cyclic ketene acetals

Preparation and radical ring-opening polymerization of the exo-methylene substituted cyclic ketene acetals, 2,4-dimethylene-1,3-dioxolane ( I ) and 2,5-dimethylene-1,3-dioxane ( II ), were carried out. Ketene acetals I and II were prepared by dehydrohalogenation of the corresponding cyclic haloacetal with potassium tert-butoxide in tetrahydrofuran at –78°C and ambient temperature, respectively. I underwent radical polymerization with essentially quantitative ring-opening with di-tert-butyl peroxide in dimethylformamide at 120°C. On the other hand, II underwent both ring-opening polymerization and vinyl polymerization under the same conditions of the polymerization of I . The differences of polymerization behavior between I and II were also discussed.     

Die stufenweise Synthese von 4,11,18,25-Tetra-tert-butyl-[1.1.1.1]metacyclophan-7,14,21,28-tetraol und 4,11-Dimethyl-[1.1.1.1]-metacyclophan-7,14,21,28-tetraol

Two phenolic alcohols with four phenolic units in their molecules are obtained by stepwise synthesis starting from simple phenolic derivatives. The phenolic alcohols are cyclized by boiling of a diluted solution in acetic acid. A third cyclic compound is obtained by debutylation of that cyclic compound which contains two neighbouringtert-butyl groups and two methyl groupspara to the phenolic hydroxyl groups.

---

---

Meiner verehrten Kollegin, Frau Prof. Dr.Helga Wittmann, Universität Graz, gewidmet.     

Selective Oxidation of Benzyl Alcohols to Aldehydes with a Salophen Copper(II) Complex and tert-Butyl Hydroperoxide at Room Temperature

An efficient and selective oxidation of benzyl alcohols has been developed using a salophen copper(II) complex as the catalyst and tert-butyl hydroperoxide (TBHP) as the oxidant in the presence of base. Moderate to excellent yields of the corresponding benzaldehydes were obtained at room temperature without the carboxylic acids being formed.     

Interactions in water-alcohol mixtures studied by NMR and infrared spectroscopy

By using low temperatures and largely deuterated solvents, the rate of OH proton exchange for aqueous solutions of alcohols is reduced sufficiently to give separate NMR signals from water and alcohol OH protons. The limiting shifts for dilute alcohols in water are down-field of both the water resonance and those of the pure alcohols. This contrasts with the limiting shift for water in the alcohols, which is to high field of the bulk water resonance. The resonance shifts initially to low fields as [ROH] increases, the rate of shift being greatest for t-butyl alcohol. For dilute aqueous solutions, all the alcohols reduce the total concentration of free OH groups, as judged by the overtone infrared spectra. Some of these results are interpreted in terms of a scavenging of free OH groups by the excess lone-pairs of the alcohol molecules. An extra, temperature dependent, down-field shift in the water proton resonance induced by t-butyl alcohol is assigned to a clathrate cage effect.     

CuCl catalyzed selective oxidation of primary alcohols to carboxylic acids with tert-butyl hydroperoxide at room temperature

Direct oxidation of primary alcohols to the corresponding carboxylic acids is performed highly efficiently at room temperature with anhydrous tert-butyl hydroperoxide in the presence of a catalytic amount of easily available CuCl under ligand free conditions in acetonitrile. Benzylic alcohols are more reactive than aliphatic alcohols, and these benzylic alcohols are selectively oxidized to the corresponding acids in the presence of aliphatic alcohols such as 1-octanol and 1-decanol.