光敏层厚度与退火温度调控对聚3-己基噻吩光电探测器性能的影响

以聚3-己基噻吩(P3HT)为给体材料,富勒烯衍生物(PC61BM)为受体材料,制备了一系列结构为ITO/PEDOT:PSS/P3HT:PC61BM/C60/Al的体异质结光电探测器.研究了120、160、180与200 nm不同光敏层厚度,100、120、130、140与150℃不同退火温度等条件对器件性能的影响,并采用原子力显微镜(AFM)对光敏层形貌进行了分析.研究发现,基于180 nm厚光敏层、150℃退火处理的器件,在-2 V的偏压下550 nm处有最大响应度,为268 mA/W,并且在470~610 nm范围内响应度都超过了200 mA/W;基于180 nm厚光敏层、120℃退火处理的器件有最大线性动态范围,为95 dB.研究表明,适当厚度的光敏层有利于提高光吸收效率与器件的光伏性能;退火处理,可以使光敏层形成均匀的互穿网络结构,进而减小空穴与电子的复合概率,提高器件的光伏性能.     

Charge trapping and storage by composite P3HT/PC60BM nanoparticles investigated by fluorescence-voltage/single particle spectroscopy

Fluorescence-voltage/single particle spectroscopy (F-V/SPS) was employed to study exciton-hole polaron interactions and interfacial charge transfer processes for pure poly(3-hexylthiophene) (P3HT) nanoparticles (NPs) and composite P3HT/PC(60)BM NPs in functioning hole-injection devices. F-V/SPS data collected on a particle-by-particle basis reveal an apparent bistability in the fluorescence-voltage modulation curves for composite NPs of P3HT and [6,6]-phenyl-C(61)-butyric acid methyl ester (PC(60)BM) that is absent for pure P3HT NPs. A pronounced deep trapping of free electrons photogenerated from the composite P3HT/PC(60)BM NPs at the NP/dielectric interface and hole trapping by fullerene anions in composite P3HT/PC(60)BM NPs under photoexcitation lies at the basis of this finding. The deep electron trapping effect reported here for composite conjugated polymer/fullerene NPs presents an opportunity for future application of these NPs in nanoscale memory and imaging devices.     

Phase diagram of P3HT:PC70BM thin films based on variable-temperature spectroscopic ellipsometry

In this article, we present the research on the influence of the composition of thin films of a blend of poly (3-hexylthiophene −2,5-diyl) - P3HT with fullerene derivatives [6,6]-phenyl-C71-butyric acid methyl ester – PC70BM and [6,6]-phenyl-C61-butyric acid methyl ester – PC60BM on their thermal transitions. The influence of molar mass (Mw) of P3HT (Mw = 65.2; 54.2 and 34.1 kDa) and PCBM (PC60BM – Mw = 911 g/mol and PC70BM – Mw = 1031 g/mol) is examined in details. The article presents significantly expanded research compared to our previous work on thermal transitions in thin films of blend P3HT (Mw = 65.2 kDa) with PC60BM. For this reason, we also compare current results with previous ones. Here, we present for the first time a phase diagram of thin films of the P3HT(Mw = 65.2 kDa):PC70BM blend using variable-temperature ellipsometry. Our research reveals the presence of characteristic temperatures of pure phases in thin films of P3HT: PCBM blends. It turns out that the cold crystallization temperature of the P3HT phase in P3HT(Mw = 65.2 kDa):PC70BM blend films is lower than corresponding temperature in P3HT(Mw = 65.2 kDa):PC60BM blend films. At the same time, the cold crystallization temperature of the PC70BM phase behaves inversely. We demonstrate also that variable-temperature spectroscopic ellipsometry is a very sensitive technique for studying thermal transitions in these thin films. In addition, we show that the entire phase diagram can be determined based on the raw ellipsometric data analysis, e.g. using a delta angle at wavelength λ = 280 nm.     

Large open-circuit voltage polymer solar cells by poly(3-hexylthiophene) with multi-adducts fullerenes

Polymer solar cells (PSCs) made by poly(3-hexylthiophene) (P3HT) with multi-adducts fullerenes, [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM), PC61BM-bisadduct (bisPC61BM) and PC61BM-trisadduct (trisPC61BM), were reported. Electrochemistry studies indicated that PC61BM, bisPC61BM and trisPC61BM had step-up distributional lowest unoccupied molecular orbital (LUMO) energy. PSCs made by P3HT with above PC61BMs show a trend of enlarged open-circuit voltages, which is in good agreement with the energy difference between the LUMO of PC61BMs and the HOMO of P3HT. On the contrary, reduced short-circuit currents (Jsc) were observed. The investigation of photo responsibility, dynamics analysis based on photo-induced absorption of composite films, P3HT:PC61BMs and n-channel thin film field-effect transistors of PC61BMs suggested that the short polaron lifetimes and low carrier mobilities were response for reduced Jsc. All these results demonstrated that it was important to develop an electron acceptor which has both high carrier mobility, and good compatibility with the electron donor conjugated polymer for approaching high performance PSCs.     

含Ullazine结构基元的共轭聚合物的合成及其光电性能研究

将Ullazine结构基元引入到聚合物主链或侧链中,分别与吡咯并吡咯二酮(DPP)、2,5-双(三甲基锡)噻吩共聚得到了二元共聚物PB和三元共聚物PT,分别利用凝胶渗透色谱和热重分析表征了聚合物的分子量和热稳定性,并研究了聚合物的光物理、电化学和光伏性能.基于共聚物PB和PT作为电子给体材料的聚合物太阳能电池器件测试结果表明,二元共聚物PB由于具有较低的能级水平从而获得较高开路电压,而侧链含Ullazine结构基元的三元共聚物PT具有更宽的吸收光谱和更高的空穴迁移率,获得了更高的短路电流和能量转换效率.     

Diketopyrrolopyrrole-based conjugated polymers as additives to optimize morphology for polymer solar cells

Novel random copolymers for optimizing the morphology of the active layer for high performance organic photovoltaic devices have been demonstrated. Three ternary random copolymers PTBDTDPPSi CN(3/7), PTBDTDPPSi CN(5/5), PTBDTDPPSi CN(7/3) were prepared by polymerization of electron-donating thienyl-substituted benzodithiophene(TBDT) with 2,5-bis[8-(1,1,3,3,5,5,5-heptamethyltrisiloxane-3-yl)octly]-pyrrolo[3,4-c]pyrrole-1,4-dione(DPPSi) and 2,5-dio[5-(5-cyano-5,5-dimethyl-pentyl)]-3,6-dithiophen-2-yl-pyrrolo[3,4-c]pyrrole-1,4-dione(DPPCN) of different ratios. The DPPCN block can well-tune the light absorption and molecular packing, while the DPPSi block is in favor of enhancing the charge mobility. And the formation of organic Si―O―Si networks is beneficial to stabilize the morphology of the active layer. These new copolymers have narrow bandgaps and broaden visible light absorption from 500 nm to 1000 nm. Careful balance of the contents of the trimethoxysilyl group and the cyano group can well-tune the surface energy and morphology of the copolymers. Incorporation of these novel copolymers as additives into the blend of poly(3-hexylthiophene)(P3HT) and [6,6]-phenyl-C60-butyric acid methyl ester(PC_(61)BM) is found to effectively broaden the light absorption, improve the compatibility and morphology of the active layer. As a result, some devices with certain ratios of these copolymers as additives achieve the enhanced efficiency compared with the device based on pristine P3HT:PC_(61)BM.     

Realizing over 10% efficiency in polymer solar cell by device optimization

The low band gap polymer based on benzodithiophene(BDT)-thieno[3,4-b]thiophene(TT)backbone,PBDT-TS1,was synthesized following our previous work and the bulk heterojunction(BHJ)material comprising PBDT-TS1/PC71BM was optimized and characterized.By processing the active layer with different additives i.e.1,8-diiodooctane(DIO),1-chloronaphthalene(CN)and 1,8-octanedithiol(ODT)and optimizing the ratio of each additive in the host solvent,a high PCE of 9.98%was obtained under the condition of utilizing 3%DIO as processing additive in CB.The effect of varied additives on photovoltaic performance was illustrated with atomic force microscopy(AFM)and transmission electron microscope(TEM)measurements that explained changes in photovoltaic parameters.These results provide valuable information of solvent additive choice in device optimization of PBDTTT polymers,and the systematic device optimization could be applied in other efficient photovoltaic polymers.Apparently,this work presents a great advance in single junction PSCs,especially in PSCs with conventional architecture.     

Effects of additives on the morphology of solution phase aggregates formed by active layer components of high-efficiency organic solar cells

Processing additives are used in organic photovoltaic systems to optimize the active layer film morphology. However, the actual mechanism is not well understood. Using X-ray scattering techniques, we analyze the effects of an additive diiodooctane (DIO) on the aggregation of a high-efficiency donor polymer PTB7 and an acceptor molecule PC(71)BM under solar cell processing conditions. We conclude that DIO selectively dissolves PC(71)BM aggregates, allowing their intercalation into PTB7 domains, thereby optimizing both the domain size and the PTB7-PC(71)BM interface.     

喷涂法制备大面积倒置聚合物光伏器件

采用喷涂工艺制备了结构为ITO/ZnO/P3HT∶PCBM/V2O5/Ag(P3HT:聚噻吩;PCBM:6,6-苯基-C61-丁酸甲酯)的大面积倒置光伏器件,有效面积为1.0×1.1 cm2。 光谱测试结果表明,退火处理后,P3HT∶PCBM薄膜吸收显著增强,并且产生一定程度的红移。 采用ZnO和V2O5代替LiF和PEDOT∶PSS(聚(3,4-乙撑二氧噻吩)∶聚苯乙烯磺酸盐)作为器件修饰层,避免了PEDOT∶PSS对ITO的腐蚀和LiF潮解,采用Ag代替Al作为金属背电极避免了Al被氧化。 经过后退火处理器件的效率从1.1%提升至1.65%。 器件的稳定性相对于传统结构有了大幅提升,8周后器件效率只衰减10%。     

聚合物:富勒烯薄膜光伏电池的反常高温热稳定性研究

聚合物太阳能电池光电转换效率已接近商业化要求,但稳定性差却成为其实用化瓶颈因素.高温暴晒是聚合物太阳能电池实用化必须面临的环境,因此提高聚合物太阳能电池的热稳定性至关重要.本文以典型的Poly(3-hexylthiophene-2,5-diyl(P3HT):[6,6]-Phenyl-C61-butyric acid methyl ester(PC61BM)基聚合物太阳能电池为研究模型,考察其在不同加热温度下(50~110℃)持续工作时的器件效率变化行为,结果发现电池在高温下表现出一种非常规的性能衰减再回升的行为,具体表现为高温下电池首先表现指数式急速衰减(20%~25%),随后发生反常的性能快速恢复至接近初始效率,之后电池保持超长的高温稳定性.光学显微镜和激光光束诱导电流成像结果证明,顶电极覆盖可以有效抑制活性层中PC61BM的聚集结晶,因而电池的反常热诱导稳定性提升与PC61BM的大量聚集结晶无关.活性层薄膜的紫外可见吸收光谱和器件外量子效率的表征结果证明,持续高温加热没有促进PC61BM二聚体的形成,反而有利于PC61BM二聚体的解离.综合实验分析结果,推测PC61BM在光照下的快速二聚反应及其高温解离是导致电池表现出反常热稳定性提升行为的主要原因.实验结果揭示了初期制备的聚合物太阳能电池实际处于一种亚稳态,对器件进行短暂的前期热退火有利于稳定活性层结构,消除亚稳态,有效提升器件稳定性.本研究工作不仅对富勒烯基聚合物太阳能电池的热诱导反常稳定性提升机理机制给出了解释,而且提供了一种提高聚合物太阳能电池稳定性的新策略.     

以C_(70)衍生物为电子受体的高效聚合物固体薄膜太阳能电池

以PC[70]BM(phenyl C71-butyric acid methyl ester)取代PC[60]BM(phenyl C61-butyric acid methyl ester)作为电子受体材料,以MEH-PPV(poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene])为电子给体材料,制成了本体异质结(bulk heterojunction,BHJ)聚合物太阳能电池.MEH-PPV/PC[70]BM器件在AM1.5G(80 mW/cm2)模拟太阳光的光照条件下得到了3.42%的能量转换效率,短路电流值达到了6.07 mA/cm2,开路电压0.85 V,填充因子为53%.通过紫外可见吸收光谱和外量子效率的研究,发现PC[70]BM作为电子受体,对扩大光谱的吸收范围和增加活性层的吸收系数有明显的作用.同时比较了不同溶剂对该体系器件性能的影响.通过原子力显微镜(AFM)、光暗导I-V曲线等研究,分析了1,2-二氯苯有利于给体相和受体相的微相分离和载流子的传输的原因.     

Efficient ternary blend bulk heterojunction solar cells with tunable open-circuit voltage

To explore the potential of ternary blend bulk heterojunction (BHJ) photovoltaics as a general platform for increasing the attainable performance of organic solar cells, a model system based on poly(3-hexylthiophene) (P3HT) as the donor and two soluble fullerene acceptors, phenyl-C(61)-butyric acid methyl ester (PC(61)BM) and indene-C(60) bisadduct (ICBA), was examined. In all of the solar cells, the overall ratio of polymer to fullerene was maintained at 1:1, while the composition of the fullerene component (PC(61)BM:ICBA ratio) was varied. Photovoltaic devices showed high short-circuit current densities (J(sc)) and fill factors (FF) (>0.57) at all fullerene ratios, while the open-circuit voltage (V(oc)) was found to vary from 0.61 to 0.84 V as the fraction of ICBA was increased. These results indicate that the V(oc) in ternary blend BHJ solar cells is not limited to the smallest V(oc) of the corresponding binary blend solar cells but can be varied between the extreme V(oc) values without significant effect on the J(sc) or FF. By extension, this result suggests that ternary blends provide a potentially effective route toward maximizing the attainable J(sc)V(oc) product (which is directly proportional to the solar cell efficiency) in BHJ solar cells and that with judicious selection of donor and acceptor components, solar cells with efficiencies exceeding the theoretical limits for binary blend solar cells could be possible without sacrificing the simplicity of a single active-layer processing step.     

Impact of 1,8-diiodooctane on the morphology of organic photovoltaic (OPV) devices – A Small Angle Neutron Scattering (SANS) study

The impact of the additive 1,8-diiodooctane on the morphology of bulk-heterojunction solar cells based on the systems P3HT:PC₇₁BM, PTB7:PC₇₁BM and PTB7-Th:PC₇₁BM is studied using a combination of Small Angle Neutron Scattering (SANS) and Atomic Force Microscopy (AFM). The results clearly show that while in the P3HT:PC₇₁BM system, the additive DIO promotes a slight coarsening of the phase domains (type I additive), in the systems PTB7:PC₇₁BM and PTB7-Th:PC₇₁BM, DIO promotes a large decrease in the size of the phase domains (type II additive). SANS is demonstrated as being particularly useful at detecting the minor morphological changes observed in the P3HT:PC₇₁BM system, which can be hardly seen in AFM. This work illustrates how SANS complements AFM and both techniques when used together provide a deeper insight into the nanoscale structure in thin organic photovoltaic (OPV) device films.     

Physical mechanisms responsible for the water-induced degradation of PC61BM P3HT photovoltaic thin films

We show that [6,6]-phenyl-C61-butyric acid methyl ester (PC₆₁BM) at the surface of thin film blends of poly(3-hexylthiophene) (P3HT):PC₆₁BM can be patterned by water. Using a series of heating and cooling steps, water droplets condense onto the blend film surface. This is possible due to the liquid-like, water swollen layer of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate. Breath pattern water deformation and subsequent drying on the film surface results in isolated PC₆₁BM structures, showing that migration of PC₆₁BM takes place. This was confirmed by selective wavelength illumination to spatially map the photoluminescence from the P3HT and PC₆₁BM. Within a device, redistribution of the surface PC₆₁BM into aggregates would be catastrophic, as it would markedly alter device performance. We also postulate that repeated volume change of the poly(3,4-ethylenedioxythiophene) polystyrene sulfonate layer by water swelling may be, in part, responsible for the delamination failure mechanism in thin film solar cells devices. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 141–146     

Dihydronaphthyl-based [60]fullerene bisadducts for efficient and stable polymer solar cells

Dihydronaphthyl-based [60]fullerene bisadduct derivative, NC(60)BA, was synthesized at mild temperature in high yield. NC(60)BA not only possesses a LUMO energy level 0.16 eV higher than PC(61)BM but also has amorphous nature that can overcome thermal-driven crystallization. The fabricated P3HT:NC(60)BA-based polymer solar cells exhibit superior photovoltaic performance and thermal stability compared to PC(61)BM-based devices under the same conditions.     

聚(3-己基噻吩)作为光谱增感层在有机太阳电池光谱响应增强中的应用

报道了利用聚(3-己基噻吩)(P3HT)作为前置缓冲层来弥补(4,8-双-(2-乙基己氧基)-苯并[1,2-b:4,5-b']二噻吩)-(4-氟代噻并[3,4-b]噻吩(PBDT-TT-F):[6,6]-苯基-C₆₁-丁酸甲酯(PC₆₁BM)共混体相异质结(BHJ)电池对450-600 nm处光谱响应不足的新的器件结构设计思路. 光谱带隙为1.8 eV的PBDT-TT-F 在550-700 nm处有很强的光谱吸收, 在有机太阳电池器件上有很好的应用潜能. 但其在350-550 nm处的吸收不强, 影响了器件对太阳光谱的利用效率. 与此相比, P3HT薄膜的光谱吸收主要在450-600 nm范围内, 同PBDT-TT-F 形成良好的互补关系. 新设计的器件外量子效率(EQE)研究结果表明, 利用P3HT 作为前置缓冲层可以与PBDT-TT-F:PC₆₁BM薄膜中的PC₆₁BM形成平面异质结, 从而拓展了器件在450-600 nm处的光谱响应范围,实现光谱增感作用. 优化P3HT的厚度为20 nm左右, 器件对外输出的短路光电流密度从11.42 mA·cm^-2提高到12.15 mA·cm^-2, 达到了6.3%的提升.     

Structural tuning of low band gap intermolecular push/pull side-chain polymers for organic photovoltaic applications

A series of novel low band gap donor-acceptor (D-A) type organic co-polymers (BT-F-TPA,BT-CZ-TPA and BT-SI-TPA) consisting of electron-deficient acceptor blocks both in main chains (M1) and at the pendant (M2) were polymerized with different electron rich donor (M3-M5) blocks,i.e.,9,9-dihexyl-9H-fluorene,N-alkyl-2,7-carbazole,and 2,6-dithinosilole,respectively,via Suzuki method.These polymers exhibited relatively low band gaps (1.65-1.88 eV) and broad absorption ranges (680-740 nm).Bulk heterojunction (BHJ) solar cells incorporating these polymers as electron donors,blended with [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) or [6,6]-phenyl-C71-butyric acid methyl ester (PC71BM) as electron-acceptors in different weight ratios were fabricated and tested under 100 mW/cm2 of AM 1.5 with white-light illumination.The photovoltaic device containing donor BT-SI-TPA and acceptor PC71BM in 1:2 weight ratio showed the best power conversion efficiency (PCE) value of 1.88％,with open circuit voltage (Voc) =0.75 V,short circuit current density (Jsc) =7.60 mA/cm2,and fill factor (FF) =33.0％.     

Facile synthesis of a 56π-electron 1,2-dihydromethano-[60]PCBM and its application for thermally stable polymer solar cells

A facile synthesis was employed to make a 56π-electron methano-PC(61)BM with a very small 1,2-dihydromethano (CH(2)) group. This new fullerene derivative possesses high electron mobility (0.014 cm(2) V(-1) s(-1)) and higher LUMO energy level (0.15 eV) than PC(61)BM. Bulk hetero-junction devices based on using poly(3-hexylthiophene) and methano-PC(61)BM as active layer exhibited better performance and thermal stability than those using the PC(61)BM analogue.     

用CdSe/ZnS量子点提高体异质结有机太阳电池的效率

通过掺杂吸收光谱在可见光波段的量子点可提高聚合物对可见光的吸收,因此掺杂CdSe/ZnS核-壳结构量子点(CQDs)能提高聚(3-己基噻吩):[6,6]-苯基-C61-丁酸甲酯(P3HT:PCBM)体异质结太阳电池的能量转换效率.本文研究了CdSe/ZnS量子点在P3HT:PCBM中的不同掺杂比例及其表面配体对太阳电池光伏性能的影响,优化器件ITO(氧化铟锡)/PEDOT:PSS(聚(3,4-乙撑二氧噻吩:聚苯乙烯磺酸)/P3HT:PCBM:(CdSe/ZnS)/Al的能量转换效率达到了3.99%,与相同条件下没有掺杂量子点的参考器件ITO/PEDOT:PSS/P3HT:PCBM/Al相比,其能量转换效率提高了45.1%.     

Compositional dependence of the open-circuit voltage in ternary blend bulk heterojunction solar cells based on two donor polymers

Ternary blend bulk heterojunction (BHJ) solar cells containing as donor polymers two P3HT analogues, high-band-gap poly(3-hexylthiophene-co-3-(2-ethylhexyl)thiophene) (P3HT(75)-co-EHT(25)) and low-band-gap poly(3-hexylthiophene-thiophene-diketopyrrolopyrrole) (P3HTT-DPP-10%), with phenyl-C(61)-butyric acid methyl ester (PC(61)BM) as an acceptor were studied. When the ratio of the three components was varied, the open-circuit voltage (V(oc)) increased as the amount of P3HT(75)-co-EHT(25) increased. The dependence of V(oc) on the polymer composition for the ternary blend regime was linear when the overall polymer:fullerene ratio was optimized for each polymer:polymer ratio. Also, the short-circuit current densities (J(sc)) for the ternary blends were bettter than those of the binary blends because of complementary polymer absorption, as verified using external quantum efficiency measurements. High fill factors (FF) (>0.59) were achieved in all cases and are attributed to high charge-carrier mobilities in the ternary blends. As a result of the intermediate V(oc), increased J(sc) and high FF, the ternary blend BHJ solar cells showed power conversion efficiencies of up to 5.51%, exceeding those of the corresponding binary blends (3.16 and 5.07%). Importantly, this work shows that upon optimization of the overall polymer:fullerene ratio at each polymer:polymer ratio, high FF, regular variations in V(oc), and enhanced J(sc) are possible throughout the ternary blend composition regime. This adds to the growing evidence that the use of ternary blends is a general and effective strategy for producing efficient organic photovoltaics manufactured in a single active-layer processing step.