Benzothiadiazole-based Conjugated Polymers for Organic Solar Cells

Benzothiadiazole(BT) is an electron-deficient unit with fused aromatic core, which can be used to construct conjugated polymers for application in organic solar cells(OSCs). In the past twenty years, huge numbers of conjugated polymers based on BT unit have been developed,focusing on the backbone engineering(such as by using different copolymerized building blocks), side chain engineering(such as by using linear or branch side units), using heteroatoms(such as F, O and S atoms, and CN group), etc. These modifications enable BT-polymers to exhibit distinct absorption spectra(with onset varied from 600 nm to 1000 nm), different frontier energy levels and crystallinities. As a consequence, BT-polymers have gained much attention in recent years, and can be simultaneously used as electron donor and electron acceptor in OSCs, providing the power conversion efficiencies(PCEs) over 18% and 14% in non-fullerene and all-polymer OSCs. In this article, we provide an overview of BTpolymers for OSCs, from donor to acceptor, via selecting some typical BT-polymers in different periods. We hope that the summary in this article can invoke the interest to study the BT-polymers toward high performance OSCs, especially with thick active layers that can be potentially used in large-area devices.     

Insulating Polymers as Additives to Bulk-Heterojunction Organic Solar Cells: The Effect of Miscibility

Adding insulating polymers to conjugated polymers is an efficient strategy to tailor their mechanical properties for flexible organic electronics. In this work, we selected two insulating polymers as additives for high-performance photoactive layers and investigated the mechanical and photovoltaic properties in organic solar cells (OSCs). The insulating polymers were found to reduce the electron mobilities in the photoactive layers, and hence the power conversion efficiencies were significantly decreased. More importantly, we found that the insulating polymers exhibited negative effect on the mechanical properties of the photoactive layers, with reduced Young's modulus and low crack onset strains. Further studies revealed that the insulating polymers had poor miscibility with the photoactive layers, providing large domains and more cavities in blend thin films, which act as negative effect for the tensile test. The studies indicate that rational selection of insulating polymers, especially enhancing the non-covalent interaction with the photoactive layers, will be critically important for the stretchable OSCs.     

A-D-A型小分子电子给体光伏材料的端基修饰及其光伏性能

有机太阳能电池(OSCs)活性层中的给体材料主要包括共轭聚合物与有机小分子,由于有机小分子给体具有结构确定、易于提纯、重复性高等独特的优势,近年来受到研究工作者的广泛关注。本工作中,我们采取具有良好共平面性的三联苯并二噻吩(TriBDT-T)为推电子(D)中心共轭单元,分别以罗丹宁(RN)、氰基罗丹宁(RCN)和1,3-茚二酮(IDO)为拉电子(A)共轭端基,设计并合成了三种具有A-D-A型结构的小分子给体材料TriBDT-T-RN、TriBDT-T-RCN和TriBDT-T-IDO。我们对比研究了三种端基对其热分解温度、吸收光谱和分子能级等基本性能的影响,并分别将三种小分子给体与非富勒烯型受体材料IT-4F共混制备器件,详细研究了活性层形貌与光伏性能之间的关系。结果表明,不同的A型端基对小分子给体材料的光学性能、电化学性能、光伏器件中活性层的微观形貌以及能量转换效率(PCE)产生显著影响。基于TriBDTT-RN:IT-4F、TriBDT-T-RCN:IT-4F和TriBDT-T-IDO:IT-4F的光伏器件的能量转换效率分别为9.25%、6.31%和6.18%。     

通过调节共轭聚合物侧链实现可绿色溶剂加工的非富勒烯太阳能电池

有机太阳能电池(OSC)经过长期的发展,其能量转换效率(PCE)已快速推进至14%–16%,基本接近可商业化应用的范围,但在目前所见报道的高效率OSC器件的制备过程中,活性层薄膜的加工大多采用氯苯、二氯苯、氯仿等毒性较高的含卤/芳香性试剂,此类试剂对环境及人类健康的危害非常高。在本工作中,我们基于已报道的高效率给体共轭聚合物PBDB-T,通过扩大共轭侧链结构与增长柔性烷基侧链的方式,合成了新型给体聚合物PBDB-DT。PBDB-DT中较长的柔性烷基侧链保证了其在低毒性溶剂四氢呋喃(THF)溶液中良好的溶解度,同时,扩大的共轭侧链也有效增强了其在THF中的溶液聚集作用,这一特性对于在非富勒烯型OSC器件中获得较好的光伏性能尤其重要。当采用非富勒烯小分子IT-M作为电子受体材料时,以THF为主溶剂加工的基于PBDB-DT:IT-M的OSC器件可以获得10.2%的能量转换效率。     

Stable Radical TEMPO Terminated Perylene Bisimide(PBI) Based Small Molecule as Cathode Interlayer for Efficient Organic Solar Cells

By combining stable radical tetramethylpiperidine nitrogen oxide(TEMPO) as end groups and perylene bisimide(PBI) as the core, a small molecular cathode interlayer(CIL) (PBI-TEMPO) was synthesized. Detailed physical-chemical characterizations indicate that PBI-TEMPO can form smooth film, owns low unoccupied molecular orbital(LUMO) level of –3.67 eV and can reduce the work function of silver electrode. When using PBI-TEMPO as CIL in non-fullerene organic solar cells(OSCs), the PM6:BTP-4Cl based OSCs delivered high power conversion efficiencies(PCEs) up to 17.37%, higher than those using commercial PDINO CIL with PCEs of 16.95%. Further device characterizations indicate that PBI-TEMPO can facilitate more efficient exciton dissociation and reduce charge recombination, resulting in enhanced current density and fill factor. Moreover, PBI-TEMPO displays higher thermal stability than PDINO in solution. When PBI-TEMPO and PDINO solution were heated at 150 ℃ for 2 h and then were used as CIL in solar cells, PBI-TEMPO-based OSCs provided a PCE of 15%, while PDINO-based OSCs only showed a PCE of 10%. These results demonstrate that incorporating TEMPO into conjugated materials is a useful strategy to create new organic semiconductors for application in OSCs.     

Rylene diimide and dithienocyanovinylene copolymers for polymer solar cells

Two polymers containing(E)-2,3-bis(thiophen-2-yl)acrylonitrile(CNTVT) as a donor unit, perylene diimide(PDI) or naphthalene diimide(NDI) as an acceptor unit, are synthesized by the Stille coupling copolymerization, and used as the electron acceptors in the solution-processed organic solar cells(OSCs). Both polymers exhibit broad absorption in the region of 300–850 nm. The LUMO energy levels of the resulted polymers are ca. –3.93 eV and the HOMO energy levels are –5.97 and –5.83 eV. In the binary blend OSCs with PTB7-Th as a donor, PDI polymer yields the power conversion efficiency(PCE) of up to 1.74%, while NDI polymer yields PCE of up to 3.80%.     

A Multifluorination Strategy Toward Wide Bandgap Polymers for Highly Efficient Organic Solar Cells

Creating new electron-deficient unit is highly demanded to develop high-performance polymer donors for non-fullerene organic solar cells (OSCs). Herein, we reported a multifluorinated unit 4,5,6,7-tetrafluoronaphtho[2,1-b : 3,4-b′]dithio-phene (FNT) and its polymers PFNT-F and PFNT-Cl. The advantages of multifluorination: (1) it enables the polymers to exhibit low-lying HOMO (≈−5.5 eV) and wide band gap (≈2.0 eV); (2) the short interactions (F⋅⋅⋅H, F⋅⋅⋅F) endow the polymers with properties of high film crystallinity and efficient hole transport; (3) well miscibility with NFAs that leads to a more well-defined nanofibrous morphology and face-on orientation in the blend films. Therefore, the PFNT-F/Cl : N3 based OSCs exhibit impressive FF values of 0.80, and remarkable PCEs of 17.53 % and 18.10 %, which make them ranked the best donor materials in OSCs. This work offers new insights into the rational design of high-performance polymers by multifluorination strategy.     

Conjugated polymers with broad absorption: Synthesis and application in polymer solar cells

A series of main chain donor‐acceptor low‐bandgap conjugated polymers were designed, synthesized, and used for the fabrication of polymer solar cells. The absorption spectra of low‐bandgap conjugated polymers were tuned by the ratio of three copolymerization monomers. The polymers in films exhibited broad absorption ranging from 300 to 1000 nm with optical bandgaps of around 1.40 eV. All of the polymers have been investigated as an electron donor in photovoltaic cells blending with PCBM ([6, 6]‐phenyl C61‐butyric acid methyl ester) as an electron acceptor and power conversion efficiencies (PCEs) of 1.32–1.8% have been obtained. As for P1 , PCE increases from 1.67 to 2.44% after adding 1,8‐diiodooctance as an additive. The higher PCEs are probably because of better phase separation of blend films. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2571–2578, 2010     

Synthesis and characterization of new sulfone‐derivatized phenylenevinylene‐based conjugated copolymers with evolving energy levels and gaps

A new series of stable, processable, and chain end functionalizable sulfone‐derivatized phenylenevinylene‐based conjugated polymers (SFPVs) containing different donor type comonomers have been synthesized and characterized. The polymer main chains are consisted of a sulfone‐phenylene electron accepting unit coupled with an electron donating unit which is derived from one of the dialdehyde comonomers based on benzene, thiophene, and pyrrole (with or without alkoxy side chains). The optical energy gaps (E_g) of the new polymers (in solvent) are in a range of 1.9–2.3 eV, with the lowest energy gap obtained from the polymer containing pyrrole as the donor unit. By using a combination of strong donor unit (such as pyrrole) and a relatively weak but stable acceptor unit (sulfone‐substituted benzene), E_g of the conjugated polymers can be tailored to below 2 eV, while the vinylene bonds on the polymer main chain are still chemically stable to survive strong basic conditions as compared with the S,S‐dioxo‐thiophene‐based PTV polymers developed earlier for potential supra‐molecular block copolymer systems. The lowest energy gap P(Pyrrole‐SFPV) exhibited 10 times better photoelectric power conversion efficiency than P(TV‐SFPV). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Theoretical study of the optical and charge transport properties of star-shaped molecules with 1,3,5-triazine-core derivatives as organic light-emitting and organic solar cells materials

A series of D–π–A star-shaped molecules has been investigated theoretically by using density functional theory (DFT) to reveal their optical, electronic, and charge transport properties for applications in organic light-emitting diodes (OLEDs) and organic solar cells (OSCs). The calculated results show that their optical, electronic, and charge transport properties are affected by the different end groups and π-bridges. Our results reveal that the molecules under investigation can serve as OSCs donor materials and/or luminescent materials for OLEDs. In addition, all molecules are expected to be promising candidates for hole- and electron-transport materials. On the basis of the obtained results, we propose a rational way for the design of multifunctional materials for OLEDs and OSCs applications.     

非富勒烯聚合物太阳电池研究进展

综述了以p-型共轭聚合物为给体、n-型有机半导体为受体的非富勒烯聚合物太阳电池光伏材料最新研究进展,包括n-型共轭聚合物和可溶液加工小分子n-型有机半导体(n-OS)受体光伏材料,以及与之匹配的p-型共轭聚合物给体光伏材料.介绍的n-型共轭聚合物受体光伏材料包括基于苝酰亚胺(BDI)、萘酰亚胺(NDI)以及新型硼氮键连受体单元的D-A共聚物受体光伏材料,目前基于聚合物给体(J51)和聚合物受体(N2200)的全聚合物太阳电池的能量转换效率最高达到8.26%.n-OS小分子受体光伏材料包括基于BDI和NDI单元的有机分子、基于稠环中心给体单元的A-D-A型窄带隙有机小分子受体材料等.给体光伏材料包括基于齐聚噻吩和苯并二噻吩(BDT)给体单元的D-A共聚物,重点介绍与窄带隙A-D-A结构小分子受体吸收互补的、基于噻吩取代BDT单元的中间带隙二维共轭聚合物给体光伏材料.使用中间带隙的p-型共轭聚合物为给体、窄带隙A-D-A结构有机小分子为受体的非富勒烯聚合物太阳电池能量转换效率已经突破12%,展示了光明的前景.最后对非富勒烯聚合物太阳电池将来的发展进行了展望.     

Bandgap engineering of indenofluorene‐based conjugated copolymers with pendant donor‐π‐acceptor chromophores for photovoltaic applications

Three narrow‐band‐gap conjugated copolymers based on indenofluorene and triphenylamine with pendant donor‐π‐acceptor chromophores were successfully synthesized by post‐functionalization approach. All the polymers have good solubility in common solvents and excellent thermal stability. The photophysical properties, energy levels and band gaps of the polymers were well manipulated by introducing different acceptor groups onto the end of their conjugated side chains. By using different acceptor groups, the band gaps of the polymers were narrowed from 1.86 to 1.53 eV by lowering their lowest unoccupied molecular orbital levels, whereas their relatively deep highest occupied molecular orbital levels of approximately ?5.35 eV were maintained. Bulk‐heterojunction solar cells with these polymers as electron donors and (6,6)‐phenyl‐C₇₁‐butyric acid methyl ester as acceptor showed power conversion efficiencies as high as 3.1% and high open circuit voltages more than 0.88 eV. The relationships between the performance and film morphology, energy levels, charge mobilities were discussed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Crystalline Conjugated Polymers for Organic Solar Cells: From Donor,Acceptor to Single‐Component

Organic solar cells have made rapid progress in the last two decades due to the innovation of conjugated materials and photovoltaic devices. Microphase separation that connects with materials and devices plays a crucial role in the charge generation process. In this account, we summary our recent works of developing new crystalline conjugated polymers to control the microphase separation in thin films in order to realize high performance in solar cells, including crystalline diketopyrrolopyrrole‐based donor polymers, perylene bisimide‐based electron acceptors, and “double‐cable” conjugated polymers that contain covalently‐linked crystalline donor and acceptor in one material for single‐component organic solar cells.     

Layer-by-Layer Organic Solar Cells Enabled by 1,3,4-Selenadiazole-Containing Crystalline Small Molecule with Double-Fibril Network Morphology

A double-fibril network of the photoactive layer morphology is recognized as an ideal structure facilitating exciton diffusion and charge carrier transport for high-performance organic solar cells (OSCs). However, in the layer-by-layer processed OSCs (LbL-OSCs), polymer donors and small molecule acceptors (SMAs) are separately deposited, and it is challenging to realize a fibril network of pure SMAs with the absence of tight interchain entanglement as polymers. In this work, crystalline small molecule donors (SMDs), named TDZ-3TR and SeDZ-3TR, were designed and introduced into the L8-BO acceptor solution, forcing the phase separation and molecular fibrilization. SeDZ-3TR showed higher crystallinity and lower miscibility with L8-BO acceptor than TDZ-3TR, enabling more driving force to favor the phase separation and better molecular fibrilization of L8-BO. On the other hand, two donor polymers of PM6 and D18 with different fibril widths and lengths were put together to optimize the fibril network of the donor layer. The simultaneously optimization of the acceptor and donor layers resulted in a more ideal double-fibril network of the photoactive layer and an impressive power conversion efficiency (PCE) of 19.38 % in LbL-OSCs.     

Side-chain engineering of high-efficiency conjugated polymer photovoltaic materials

In recent years,conjugated polymers have attracted great attention in the application as photovoltaic donor materials in polymer solar cells(PSCs).Broad absorption,lower-energy bandgap,higher hole mobility,relatively lower HOMO energy levels,and higher solubility are important for the conjugated polymer donor materials to achieve high photovoltaic performance.Side-chain engineering plays a very important role in optimizing the physicochemical properties of the conjugated polymers.In this article,we review recent progress on the side-chain engineering of conjugated polymer donor materials,including the optimization of flexible side-chains for balancing solubility and intermolecular packing(aggregation),electron-withdrawing substituents for lowering HOMO energy levels,and two-dimension(2D)-conjugated polymers with conjugated side-chains for broadening absorption and enhancing hole mobility.After the molecular structural optimization by side-chain engineering,the2D-conjugated polymers based on benzodithiophene units demonstrated the best photovoltaic performance,with powerconversion efficiency higher than 9%.     

Synthesis and characterization of light‐emitting oligo(p‐phenylene‐vinylene)s and polymeric derivatives containing three‐ and five‐conjugated phenylene rings

Several series of light‐emitting oligo(p‐phenylene‐vinylene)s (BIII and BV series containing three‐ and five‐conjugated phenylene rings) with various side groups and end groups attached to the cores were synthesized and characterized. The analogous PBV polymers, derived from the BV series, were also synthesized and investigated. Blue and greenish light emissions were observed in the photoluminescence (PL) and electroluminescence (EL) spectra of the blend and pure films with these π‐conjugated structures. In contrast to the three‐conjugated ring oligomers, the five‐conjugated ring derivatives (oligomers and polymers) had larger maximum emission wavelength values of PL and EL emissions. Mesomorphism was introduced into the BV series by the replacement of three‐conjugated rings (BIII series) with five‐conjugated phenyl cores (BV series). The liquid‐crystalline properties of the BV series with end groups (on both end rings) were better than those of analogous BV‐OC₈ without end groups. Polarized PL emissions were obtained by the alignment of liquid‐crystalline phase in rubbing cells. Upon heating, different PL emission wavelengths and intensities were observed in various phases. Not only the solubility and thermal properties but also the PL and EL properties could be effectively adjusted by the attachment of flexible alkoxy groups either on the central rings or on both end rings of the conjugated cores. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 783–800, 2006     

Optimal bulk-heterojunction morphology enabled by fibril network strategy for high-performance organic solar cells

A bicontinuous network formed spontaneously upon film preparation is highly desirable for bulk-heterojunction(BHJ) organic solar cells(OSCs). Many donor-acceptor(D-A) type conjugated polymers can self-assemble into polymer fibrils in the solid state and such fibril-assembly can construct the morphological framework by forming a network structure, inducing the formation of ideal BHJ morphology. Our recent works have revealed that the fibril network strategy(FNS) can control the blend morphology in fullerene, non-fullerene and ternary OSCs. It has been shown that the formation of fibril network can optimize phase separation scale and ensure efficient exciton dissociation and charge carriers transport, thus leading to impressive power conversion efficiencies(PCEs) and high fill factor(FF) values. We believe that FNS will provide a promising approach for the optimization of active layer morphology and the improvement of photovoltaic performance, and further promote the commercialization of OSCs.     

Crystalline Cooperativity of Donor and Acceptor Segments in Double‐Cable Conjugated Polymers toward Efficient Single‐Component Organic Solar Cells

The crystalline cooperativity of the donor and acceptor segment in double‐cable conjugated polymers plays an important role in the nanophase separation and photovoltaic performance in single‐component organic solar cells (SCOSCs). Two double‐cable conjugated polymers with the same conjugated backbone and perylene bisimide (PBI) side units were designed in which PBIs were positioned symmetrically and perpendicularly ( P1 ) and asymmetrically and slantingly ( P2 ) along the conjugated backbones. After thermal annealing, both conjugated backbones and PBI side units in P1 tend to form ordered nanostructures, while PBI side units in P2 dominated the crystallization and hamper the crystallization of conjugated backbones. P1 showed good crystalline cooperativity between conjugated backbones and PBI side units, resulting in improved power conversion efficiencies (PCEs) up to 3.43 % in SCOSCs, while P2 with poor crystalline cooperativity exhibited PCEs below 2.42 %.     

Synthesis and characterization of new low bandgap polyfluorene copolymers for bulk heterojunction solar cells

Two new low bandgap alternating polyfluorene copolymers based on dioctylfluorene and donor‐acceptor‐donor monomers have been synthesized via a Suzuki polymerization reaction. The resulting copolymers have low optical bandgaps at 1.99–1.98 eV. The bulk heterojunction polymer solar cells were fabricated with the conjugated polymers as the electron donor and 6.6‐phenyl C₆₁‐butyric acid methyl ester as the electron acceptor. The power conversion efficiencies of the solar cells based on copolymers 1 and 2 are 0.37 and 0.42%, respectively, under the illumination of AM 1.5, 100 mW/cm². The results indicate that the two copolymers are promising conjugated polymers for polymer solar cells. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5336–5343, 2009     

Photovoltaic properties of the polymer solar cells comprising crosslinked maleimide polymers and fullerene‐derivative PCBM

A series of crosslinkable maleimide conjugated polymers with different vinyl group contents as side‐chain crosslinking sites have been synthesized by the Suzuki coupling reaction. Polymer solar cells (PSCs) were fabricated based on an interpenetrating network of the crosslinkable maleimide polymers as the electron donor, and a fullerene derivative, (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM), as the electron acceptor. The crosslinkable maleimide polymers underwent crosslinking reaction at the side‐chain vinyl groups upon the thermal treatment with or without the addition of initiator, azobisisobutyronitrile (AIBN). Better photovoltaic (PV) performances were obtained for the PSCs based on the polymer crosslinking without using initiator, whereas poorer PV performances were observed for the PSCs based on the polymer crosslinking with the AIBN initiator. In addition, higher operational stability was observed for the crosslinked polymer based solar cell as compared to the solar cell based on the un‐crosslinked polymer. The photo‐physical and PV properties of the cross‐linked maleimide polymers/PCBM based PSCs are discussed in detail as the morphology and crosslinking density of the polymers are taken into account. Copyright © 2010 John Wiley & Sons, Ltd.