Rheo-SANS studies on shear-thickening/thinning in aqueous rodlike micellar solutions

Shear-induced thickening/thinning phenomena of aqueous rodlike micellar solutions of cetyltrimethylammonium bromide (CTAB) and sodium p-toluene sulfonate (NapTS) were investigated by means of simultaneous measurements of rheology and small-angle neutron scattering (SANS), the so-called Rheo-SANS. The aqueous CTAB/NapTS solutions were classified into five different categories dependent on their flow behavior and micellar structure. By increasing salt concentration and/or shear rates, the micelles underwent morphological transition from (i) spherical or short rodlike micelles to (ii) long rodlike micelles without entanglements, followed by (iii) those with entanglements. These transitions were recognized as changes in flow behavior from Newtonian to shear-thickening and shear-thinning flow, respectively. In the latter two cases, anisotropic SANS patterns appeared around these critical shear rates. The physical meaning of the anisotropic SANS patterns accompanied by shear-thickening flow behavior is discussed in conjunction with other shear-thickening systems.     

Viscoelastic micellar water/CTAB/NaNO(3) solutions: rheology, SANS and cryo-TEM analysis

Aqueous micellar solutions of the cationic surfactant hexadecyltrimethylammonium bromide (CTAB) and sodium nitrate (NaNO(3)) were examined using steady and dynamic rheology, small-angle neutron scattering (SANS) and cryogenic-transmission electron microscopy (cryo-TEM). Upon addition of NaNO(3), the CTAB spherical micelles transform into long, flexible wormlike micelles, conveying viscoelastic properties to the solutions. The zero-shear viscosity (eta(0)) versus NaNO(3) concentration curve exhibits a well-defined maximum. Likewise, upon increase in temperature, the viscosity decreases. Dynamic rheological data of the entangled micellar solutions can be well described by the Maxwell model. Changes in the structural parameters of the micelles with addition of NaNO(3) were inferred from SANS measurements. The intensity of scattered neutrons at the low q region was found to increase with increasing NaNO(3) concentration. This suggests an increase in size of the micelles and/or decrease of intermicellar interactions with increasing salt concentration. Analysis of the SANS data using prolate ellipsoidal structure and Yukawa form of interaction potential between micelles indicates that addition of NaNO(3) leads to a decrease in the surface charge of the ellipsoidal micelles and consequently an increase in their length. The structural transition from spherical to entangled threadlike micelles, induced by the addition of NaNO(3) to CTAB micelles is further confirmed by cryo-TEM.     

Self-assembly of surfactant vesicles that transform into viscoelastic wormlike micelles upon heating

Unilamellar vesicles are observed to form in aqueous solutions of the cationic surfactant, cetyl trimethylammonium bromide (CTAB), when 5-methyl salicylic acid (5mS) is added at slightly larger than equimolar concentrations. When these vesicles are heated above a critical temperature, they transform into long, flexible wormlike micelles. In this process, the solutions switch from low-viscosity, Newtonian fluids to viscoelastic, shear-thinning fluids having much larger zero-shear viscosities (e.g., 1000-fold higher). The onset temperature for this transition increases with the concentration of 5mS at a fixed CTAB content. Small-angle neutron scattering (SANS) measurements show that the phase transition from vesicles to micelles is a continuous one, with the vesicles and micelles coexisting over a narrow range of temperatures. The tunable vesicle-to-micelle transition and the concomitant viscosity increase upon heating may have utility in a range of areas, including microfluidics, controlled release, and tertiary oil recovery.     

Structural behaviour of mixed cationic surfactant micelles: a small-angle neutron scattering study

Self-assembly in mixtures of two single-chain cationic surfactants, with different tail lengths (CTAB and DTAB) as well as of a single-chain (DTAB) and a double-chain (DDAB) cationic surfactant, with identical tail lengths, have been investigated with small-angle neutron scattering (SANS) and rationalised in terms of bending elasticity properties. The growth behaviour of micelles with respect to surfactant composition appears completely different in the two surfactant mixtures. DTAB form small oblate spheroidal micelles in presence of [NaBr] = 0.1 M that transform into prolate spheroidal mixed CTAB/DTAB micelles upon adding moderate amounts of CTAB, so as to give a mole fraction y = 0.20 in solution. Most unexpectedly, upon further addition of CTAB the mixed CTAB/DTAB micelles grow with an almost equal rate in both length and width directions to form tablets. In contrast to this behaviour, mixed DDAB/DTAB micelles grow virtually exclusively in the length direction, in presence of [NaBr] = 0.1 M, to form elongated ellipsoidal (tablet-shaped) and subsequently long wormlike micelles as the fraction of DDAB in the micelles increases. Mixed DDAB/DTAB micelles grow to become as long as 2000 Å before an abrupt transition to large bilayer structures occurs. This means that the micelles are much longer at the micelle-to-bilayer transition as compared to the same mixture in absence of added salt. It is found that the point of transition from micelles to bilayers is significantly shifted towards higher fractions of aggregated DTAB as an appreciable amount of salt is added to DDAB/DTAB mixtures, indicating a considerable reduction of the spontaneous curvature with an increasing [NaBr]. By means of deducing the various bending elasticity constants from our experimental results, according to a novel approach by ours, we are able to conclude that the different growth behaviours appear as a consequence of a considerably lower bending rigidity, as well as higher saddle-splay constant, for DDAB/DTAB surfactant mixtures in presence of [NaBr] = 0.1 M, as compared to mixtures of CTAB/DTAB in [NaBr] = 0.1 M and DDAB/DTAB in absence of added salt.     

A phenol-induced structural transition in aqueous cetyltrimethylammonium bromide solution

The effect of phenol on the structure of micellar solution of a cationic surfactant, cetyltrimethylammonium bromide (CTAB) was investigated using viscosity, dynamic light scattering (DLS), small angle neutron scattering (SANS) and nuclear magnetic resonance (NMR) techniques. The relative viscosity and apparent hydrodynamic diameters of the micelles in CTAB solution increase initially and then decrease with addition of phenol. SANS studies indicate a prolate ellipsoidal structure of the micelles. The axial ratio of the prolate ellipsoidal micelles increases and then decreases with addition of phenol, consistently with DLS and viscosity measurements. NMR studies confirm the solubilization of phenol to the palisade layer and growth of the micelles at high concentration of phenol as revealed from the broadening of peaks.     

Unusual vesicle-micelle transitions in a salt-free catanionic surfactant: temperature and concentration effects

The spontaneous formation of vesicles by the salt-free surfactant hexadecyltrimethylammonium octylsulfonate (TASo) and the features of an unusual vesicle-micelle transition are investigated in this work. In a previous work, we have shown that this highly asymmetric catanionic surfactant displays a rare lamellar miscibility gap in the concentrated regime. Here, we analyze in detail the aggregation behavior in the dilute regime (less than 3 wt % surfactant) as a function of both concentration and temperature. The phase diagram is dominated by a two-phase region consisting of a dispersion of a swollen lamellar phase (Lalpha') in the excess solvent phase (L1). Stable vesicles form in this two-phase region, and upon temperature increase, a transition to a single solution phase containing only elongated micelles occurs. The structural characterization of the aggregates and the investigation of their equilibrium properties have been carried out by light microscopy, cryo-TEM, water self-diffusion NMR, and SANS. Similarly to the lamellar-lamellar coexistence, the changes in microstructure at high dilution and high temperature can be understood from solubility differences, electrostatic interactions, and preferred aggregate curvature. Surface charge in the aggregates stems from the higher solubility of the octylsulfonate (So-) ion as compared to that of the hexadecyltrimethylammonium ion (TA+). Upon temperature increase, the ratio of free So(-) relative to the neutral TASo increases. Consequently, the surface charge density of the aggregates increases, and this ultimately induces a transition to a higher-curvature morphology (elongated micelles). Vesicles can also be spontaneously formed by cooling solutions from the micellar region, and the mean size obtained is practically independent of cooling rate, suggesting that dissociation/charge effects also control this process.     

Aggregation behavior of aqueous solutions of ionic liquids

The aggregation behavior in aqueous solutions of three ionic liquids based on the 1-alkyl-3-methylimidazolium cation has been investigated by means of surface tension, conductivity, and small-angle neutron scattering (SANS) measurements. From analysis of the SANS data, models for the shapes and sizes of aggregates have been proposed: the short-chain 1-butyl-3-methylimidazolium tetrafluoroborate [C4mim] [BF4] system can be best modeled by treating it as a dispersion of polydisperse spherical aggregates that form above a critical aggregation concentration, whereas the 1-octyl-3-methylimidazolium iodide, [C8mim] [I], solutions can be modeled as a system of regularly sized near-spherical charged micelles that form above a critical micelle concentration. Solutions of 1-octyl-3-methylimidazolium chloride, [C8mim]-[Cl], display weak long-range ordering of possibly disklike particles culminating in the formation of structures with distinct long-range order at higher concentrations.     

Microrheology of wormlike micellar fluids from the diffusion of colloidal probes

The microrheology of cationic micellar solutions has been investigated as a function of added organic salts using quasielastic light scattering (QELS). Two organic salts, sodium p-toluene sulfonate and sodium salicylate, were used to induce microstructural changes in cetyl trimethylammonium bromide (CTAB) micelles. The mean-squared displacement (MSD) of polystyrene probe particles embedded in CTAB micellar solutions was monitored by QELS in the single-scattering regime. Through the use of the generalized Stokes-Einstein relationship, the frequency-dependent complex shear moduli of each fluid were estimated from the Laplace transform of the corresponding MSD. The salt-induced transition from nearly spherical to elongated wormlike micelles and consequent changes in fluid response from viscous to viscoelastic are clearly captured by microrheology.     

Kinetics of interaction of Histidine and Histidine Methyl Ester with Ninhydrin in micellar media

Kinetics of the interaction of histidine and histidine methyl ester with ninhydrin under varying concentrations of reactants, anionic (sodium dodecyl sulphate, SDS), cationic (cetyltrimethylammonium bromide, CTAB) and non‐ionic (Triton X‐100, TX‐100) micelles have been carried out. Rate of the reaction was found to be independent of the initial concentration of histidine (and histidine methyl ester) but was dependent on [Ninhydrin]. The SDS micelles had no effect on the rate of the reaction. In the presence of the CTAB micelles a small enhancement in the rate was observed. The rate − [CTAB] profile showed that the increase in [CTAB] increased the rate up to a maximum value and a further increase had a decreasing effect on the rate. The rate was enhanced by TX‐100 also but, unlike CTAB micelles, TX‐100 possessed a curve without peak for the rate − [TX‐100] profile. The following rate equation was obeyed by the reaction in CTAB and TX‐100 micelles: Values of k_w, k_m, and K_S were evaluated and are reported herein. ©1999 John Wiley & Sons, Inc. Int J Chem Kinet 31: 103–111, 1999     

Effect of hydrotropes on the solution behavior of PEO/PPO/PEO block copolymer L62 in aqueous solutions

Effect of hydrotropes viz. sodium benzene sulfonate (NaBS), sodium toluene sulfonate (NaTS) and sodium xylene sulfonate (NaXS) on the micellization, phase behavior and structure of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymer L62 in aqueous solution was studied by surface tension, dye spectral, cloud point and small angle neutron scattering measurements. The addition of hydrotropes increased the critical micelle concentration (CMC) of L62 which appears to be logistic as the added hydrotrope enhances the solubility of PPO moiety (and PEO) making it behave like a more hydrophilic block copolymer that would micellize at high copolymer concentration. Partial phase diagram of L62 in water shows two cloud point (CP) in the concentration range (0-10 wt.%). Addition of hydrotropes shifts the L62 concentration range showing double cloud points at lower side of concentration; sodium xylene sulfonate (NaXS) being more effective. SANS data for L62 in the presence of 0.4 and 0.8 M NaXS at temperatures <30 °C showed unimers which are fully dissolved Gaussian chains. The unimer-to-micelle transition takes place when temperature is increased. It is found that SANS data for L62 in the presence of 0.4 M NaXS (40 and 50 °C) and 0.8 M NaXS (45 and 50 °C) correspond to ellipsoidal structure of micelles.     

Micellar Behavior of Polystyrene-Poly(Ethylene Oxide) Diblock Copolymers in Aqueous Media: Effect of Copolymer Composition,Temperature, Salt,and Surfactants

Formation and structure of micelles from two amphiphilic polystyrene-block-poly(ethylene oxide) (PS-PEO) diblock copolymers (PS mol.wt. 1000; PEO mol.wt. 3000 and 5000) were examined by surface tension, viscosity, steady state fluorescence, dynamic light scattering (DLS), small angle neutron scattering (SANS), and cryo-transmission electron microscopy (cryo-TEM). The critical micelle concentration (CMC) of the copolymers in aqueous solution was ca. 0.05%; micelle hydrodynamic diameter was 30–35 nm with a narrow size distribution. SANS studies show that the copolymers form ellipsoidal micelles with semi major axis ～23 nm and semi minor axis ～8 nm. No significant change in the structure was found with temperature and presence of salt. The copolymer micelles interaction with the ionic surfactants sodium dodecyl sulphate (SDS) and dodecyltrimethylammonium bromide (DTAB) was also examined by DLS and SANS.     

Micellar shape transition under dilute salt-free conditions: promotion and self-fluorescence monitoring of stimuli-responsive viscoelasticity by 1- and 2-naphthols

Effect of 1 and 2-naphthols on the shape transition of cetyl trimethylammonium bromide (CTAB) and cetylpyridinium bromide (CPB) micelles are studied. Stimuli-responsive viscoelastic gels of long wormlike micelles are formed at low surfactant concentrations in the presence of neutral naphthols, where H-bonding plays a key role in micellar shape transition in the absence of any charge screening. Micelle-embedded naphthols also act as novel self-fluorescence probes for monitoring viscoelasticity of the system as a function of applied shear. 1H NMR study shows that the solubilization sites of naphthols in the micelle are located near the surface. While UV absorption and Fourier transform infrared studies confirm the presence of intermolecular H-bonds in micelle embedded naphthols, transmission electron micrographs of vacuum-dried samples at room temperature demonstrate the transition in shape from sphere to rodlike micelles.     

(1)H NMR and small-angle neutron scattering investigation of the structure and solubilization behavior of three-layer nanoparticles

Three-layer nanoparticles were prepared by radiation-induced polymerization of 1-10 g/L of methyl methacrylate dissolved in a 0.1 wt % D(2)O solution of polystyrene-poly(methacrylic acid) (PS-PMA) micelles. According to NMR and small-angle neutron scattering (SANS), most of the poly(methyl methacrylate) (PMMA) is adsorbed at the core-shell interface of the particles. A small fraction of shorter PMMA probably sticks to outer parts of the PMA chains. The absorption kinetics and equilibria of benzene and chloroform were studied by NMR and SANS time-resolved experiments. The diffusion front in the PS core is very narrow but quite broad in the PMMA sheet suggesting, thus, a less compact state of PMMA. According to SANS, the diffusion kinetics is almost independent of the PMMA sheet thickness. In contrast to it, the absorption capacity, reflected by both SANS and NMR, increases markedly with the PMMA content in the particle. The maximum amount of solubilized compound depends on its positive interaction with PMMA (expressed by the chi parameter) but is restricted by the growing interface tension between swollen PMMA and D(2)O. In accordance with this conclusion, a particle saturated with benzene can absorb chloroform only at the expense of a part of benzene expelled into the surrounding medium and vice versa. Starting with 10 g PMMA/L (10 times the weight of the original micelles), the particles become unstable when being swollen with a good solvent.     

Reactivity of supramolecular systems based on calix[4]resorcinarene derivatives and surfactants in hydrolysis of phosphorus acid esters

The formation of mixed micelles of amphiphilic calix[4]resorcinarenes with aminomethyl (AMC, PAMC), tris(hydroxymethyl)amide (THAC) fragments and the cationic surfactant cetyl trimethylammonium bromide (CTAB) in water and aqueous DMF solutions (10-50% DMF) leads to the decrease of the critical micelle concentration of the systems and the increase of the size of the mixed micelles in comparison with CTAB micelles. The catalytic activity of the mixed systems in the hydrolysis of phosphorus acid esters is higher than those of CTAB micelle and AMC, PAMC or THAC aggregates.     

Wormlike micelles mediated by polyelectrolyte

Aqueous solutions of the anionic surfactant potassium oleate (K-oleate) were studied using small-angle neutron scattering (SANS), steady-state rheology, and cryogenic transmission electron microscopy (cryo-TEM). The micellar structural changes induced by the addition of potassium chloride (KCl) and sodium polystyrenesulfonate (PSS) of different molecular weights were investigated. Upon addition of KCl, a transition from spherical to wormlike micelles was detected from the SANS data and confirmed by the cryo-TEM pictures. The rheological measurements revealed a strong dependence of the low-shear viscosity on the concentration of salt: a broad maximum in the viscosity curve was observed upon addition of KCl, characteristic of the growth of micelles into long worms, followed by branching. The addition of PSS to salt-free solutions of K-oleate had a significant effect on the scattering patterns, revealing partial growth of the spherical micelles into rodlike micelles. In contrast, in the presence of high salt concentrations, addition of PSS to solutions of wormlike micelles did not bring any noticeable modifications in the scattering. However, in the same salt conditions, a clear effect was observed on the low shear viscosity upon addition of PSS, which was found to depend significantly on molecular weight. This suggests a novel way of impacting the viscosity of solutions of wormlike micelles.     

Geometrical shape of micelles formed by cationic dimeric surfactants determined with small-angle neutron scattering

The influence of spacer group on the geometrical shape of micelles formed by quaternary-bis dimeric (Gemini) surfactants C(12)H(25)N(CH(3))(2)(CH(2))(s)N(CH(3))(2)C(12)H(25) (12-s-12) has been investigated with small-angle neutron scattering (SANS). Dimeric surfactants with a short spacer unit (12-3-12 and 12-4-12) are observed to form elongated general ellipsoidal micelles with half axes a < b < c, whereas SANS data demonstrate that 12-s-12 surfactants with 6 ≤ s ≤ 12 form rather small spheroidal micelles rather than strictly spherical micelles. By means of comparing our present SANS results with previously determined growth rates using time-resolved fluorescence quenching, we are able to conclude that micelles formed by 12-6-12, 12-8-12, 12-10-12, and 12-12-12 are shaped as oblate rather than prolate spheroids. As a result, our present investigation suggests a never before reported structural behavior of Gemini surfactant micelles, according to which micelles transform from elongated ellipsoids to nonelongated oblate spheroids as the length of the spacer group is increased. The aggregation number of oblate micelles is observed to monotonously decrease with an increasing length of the surfactant spacer group, mainly as a result of a decreasing minor half axis (a), whereas the major half axis (b) is rather constant with respect to s. We argue that geometrically heterogeneous elongated micelles are formed by dimeric surfactants with a short spacer group mainly as a result of the surface charges becoming less uniformly distributed over the micelle interface. As the length of the spacer group increases, the distance between intramolecular charges become approximately equal to the average distance between charges on the micelle interface, and as a result, rather small oblate spheroidal micelles with a more uniform distribution of surface charges are formed by dimeric 12-s-12 surfactants with 6 ≤ s ≤ 12.     

Mononuclear iron(III) complexes of 3N ligands in organized assemblies: spectral and redox properties and attainment of regioselective extradiol dioxygenase activity

Four octahedral iron(III) complexes of the type [Fe(L)Cl(3)], where L is a tridentate 3N ligand like N,N-bis(pyrid-2-ylmethyl)amine (bpa, L1), N,N-bis(benzimidazol-2-ylmethyl)amine (bba, L2), 1,4,7-triazacyclononane (tacn, L3) and 2,2';6',2'-terpyridine (terpy, L4), have been isolated and their catechol dioxygenase activity investigated in dichloromethane, water and different aqueous micellar media. The positions of both the catecholato-to-iron(III) LMCT bands observed for the DBC(2-) (H(2)DBC = 3,5-di-tert-butylcatechol) adducts reveal that the adducts are present as cationic [Fe(L)(DBC)(H(2)O)](+) species, which interact strongly with anionic SDS micelles and dock themselves on the anionic micellar surface, and that they exist in the aqueous phase in CTAB and TX 100 micelles. The Fe(III)/Fe(II) redox potentials of the complexes throw light on the Lewis acidity of the iron(III) center as modified by the ligand donor atoms and hence the interaction of the complexes with different micelles. The DBSQ/DBC(2-) redox potentials in SDS micellar media are more positive than those in aqueous solution confirming the presence of the aqua species [Fe(L)(DBC)(H(2)O)](+). The DBC(2-) adducts of the iron(III) complexes of bpa, bba and tacn ligands, all with facial coordination, elicit extradiol (E) cleavage to different extents while the adduct of the terpy complex with meridional coordination of the ligand shows always intradiol (I) cleavage. It is remarkable that the bpa complex shows the highest yield of extradiol product and high product selectivity in aqueous SDS solution (E, 84.0%; E/I, 61.0?:?1) and in SDS?:?n-hexane reverse micellar medium (E, 93.7%) illustrating that a vacant or solvent coordinated site is essential for observing extradiol cleavage. Interestingly, the rates of dioxygenase reactions in aqueous and aqueous micellar solutions are significantly higher than those in non-aqueous solvents. Also, they diminish in the order, SDS > TX-100 > CTAB, illustrating the facile substitution of coordinated water molecule by molecular oxygen in [Fe(L)(DBC)(H(2)O)](+) bound to anionic SDS micelles.     

Preparation and solution behavior of a thermoresponsive diblock copolymer of poly(ethyl glycidyl ether) and poly(ethylene oxide)

A thermoresponsive diblock copolymer, poly(ethyl glycidyl ether)-block-poly(ethylene oxide) (PEGE-b-PEO), is synthesized by successive anionic ring-opening polymerization of ethyl glycidyl ether and ethylene oxide using 2-phenoxyethanol as a starting material, and its solution behavior is elucidated in water. In a dilute 1 wt % solution, the temperature-dependent alteration in the polymer hydrodynamic radius (RH) is measured in the temperature range between 5 and 45 degrees C by pulse-gradient spin-echo NMR and dynamic light scattering. The RH value increased with temperature in two steps, where the first step at 15 degrees C corresponds to the core-shell micelle formation and the second step at 40 degrees C corresponds to the aggregation of the core-shell micelles. The formation of the core-shell micelles is supported by the solubilization of a dye (1,6-diphenyl-1,3,5-hexatriene) in the hydrophobic core, which is recognized for a copolymer solution in the temperature range between 20 and 40 degrees C. In this temperature range, the core-shell micelles and the unimers coexist and the fraction of the former gradually increases with increasing temperature, suggesting equilibrium between the micelles and the unimers. In the concentrated regime (40 wt % solution), the solution forms a gel and the small-angle X-ray scattering measurements reveal the successive formation of hexagonal and lamellar liquid crystal phases with increasing temperature.     

多壁碳纳米管对聚甲醛性能的影响

将多壁碳纳米管(MWCNTs)和聚甲醛(POM)在转矩流变仪中熔融混合得到POM/MWCNT复合材料.研究了复合材料的形态,导热性能,导电性能,流变性能和结晶性能.结果表明,MWCNTs在没有经过处理的情况下能够均匀地分散在POM基体中;当向POM中添加1.0 wt%含量MWCNTs时,复合材料的导热系数上升到0.5289 W/(K m),比纯POM的导热系数0.198 W/(K m)提高1.5倍,通过有效介质方法(EMA)验证了体系导热系数提高幅度不大的原因是MWCNTs与POM之间形成了很高的界面热阻;当MWCNTs的含量为1.0 wt%时,体系产生了导电逾渗效应,逾渗值在0.5 wt%~1.0 wt%之间;MWCNTs对POM有显著的成核作用,当向POM中添加0.5 wt%含量的MWCNTs时,POM的结晶温度提高6℃左右,但当MWCNTs的添加量进一步增加时,结晶温度几乎不再变化,成核效果呈现"饱和"状态.另外,材料的复数黏度,储能模量和损耗模量随MWCNTs含量的增加而增加.