A Microwave Photonic Notch Filter Using a Microfiber Ring Resonator

A novel tunable microwave photonic filter based on a microfiber ring resonator is proposed and experimentally demonstrated. A fiber ring laser based on the microfiber ring resonator is employed to generate two singlelongitudinal-mode carriers, then the dispersive element introduces the delay between two modulated carriers. By adjusting the diameter of the microfiber ring resonator, the proposed microwave photonic notch filter can be continuously and widely tuned. The measured notch rejection ratio is greater than 35 dB, and there is good agreement between the experimental result and the theoretical analysis.     

A Single Mode Fibre Laser by Applying Self-Injection Locking with a DFB Structure

We report a novel single-frequency fibre ring laser using self-injection locking with a distributed-feedback （DFB） fibre laser at 1550nm. The operating wavelength is controlled by a saturable absorber and a DFB fibre laser in the ring cavity, the saturable absorber acts as a narrow band-pass filter. In the primary experiment, the laser output exceeds 100mW with the linewidth less than 2kHz. The laser is stable, and no mode-hopping is observed within eight hours. Compared with other cavity designs using spatial hole-burning, our laser shows high controllability.     

A Proposal and Demonstration for Photonic Generation of a Microwave Signal by Incorporating a Microring Resonator

A proposal for photonic generation of a microwave signal is presented by employing a dual wavelength erbiumdoped fibre ring laser. In the laser, a microring resonator is cascaded with a tunable bandpass filter to serve as a dual-wavelength selector, an unpumped polarization maintaining erbium-doped fibre is used as a saturable absorber. By replacing the microring resonator with a delay interferometer to verify the proposal, a wavelengthtunable dual wavelength single longitudinal mode laser is demonstrated, and a microwave signal at 10.01 GHz with a linewidth of less than 25 kHz is obtained by beating the two wavelengths at a photodetector.     

Realization of Stable Narrow Linewidth Dual-Wavelength Lasing in an Erbium-Doped Fibre Laser by Cleaving the Wavelength-Selective Filter Spectrum

We propose and demonstrate a new concept of stable narrow-line-width and close wavelength spacing dualwavelength lasing in an Er-doped fibre ring laser （EDFRL） by cleaving the spectrum with a wavelength-selective component in the EDFRL. A fibre loop mirror （FLM） combining with a polarization controller （PC） acts as the cleaver. The cleaver can produce a fine pectinate spectrum. By adjusting the PC, the fine pectinate spectrum can be so changeable that cleaving the spectrum of a fibre Bragg grating （FBG） into two parts. As a result, we obtain the dual-wavelength fibre lasering with a bandwidth of only 0.03nm and a wavelength spacing of only 0.07nm. Furthermore, the laser can also perform stable switchable single wavelength or stable different-bandwidth dual-wavelength by carefully adjusting the PC at room temperature.     

Broadly Tunable SOA-Based Active Mode-Locked Fibre Ring aser by Forward Injection Optical Pulse

We present a broadly tunable active mode-locked fibre ring laser based on a semiconductor optical amplifier （SOA）, with forward injection optical pulses. The laser can generate pulse sequence with pulsewidth about 12ps and high output power up to 8.56 dBm at 2.5 GHz stably. Incorporated with a wavelength-tunable optical bandpass filter, the pulse laser can operate with a broad wavelength tunable span up to 37nm with almost constant pulsewidth. A detailed experimental analysis is also carried out to investigate the relationship between the power of the internal cavity and the pulsewidth of the output pulse sequence. The experimental configuration of the pulse laser is very simple and easy to setup with no polarization-sensitive components.     

Tunable Fiber Ring Laser Employing a Sagnac Interferometric Filter

A tunable erbium-doped fiber ring laser employing an all -polarization- maintaining fiber loop filter with certain birefringence is proposed and demonstrated. The lasing frequencies can be selected by properly adjusting the polarization controller in the cavity.     

基于高双折射光子晶体光纤与光纤环的超宽带可调谐微波光子滤波器

提出一种基于高双折射光子晶体光纤与光纤环的超宽带可调谐微波光子滤波器.以多波长光纤激光器作为光源,向高双折射光子晶体光纤内填充温敏液体,通过改变填充温敏液体的温度,高双折射光子晶体光纤可具有不同的双折射,得到不同波长间隔的激光,从而使微波光子滤波器具有不同的自由频谱范围.当温度的变化范围为20~80℃时,仿真测得微波光子滤波器自由频谱的变化范围为2.49~39.9GHz.引入光纤环构建级联型微波光子滤波器,滤波器的主旁瓣抑制比可提高到33.6dB,Q值可达到499,提高了滤波器的频率选择性.     

基于多模光纤滤波器的可调谐掺铒光纤激光器

研究了一种新型、全光纤、宽带可调谐环形腔掺铒光纤激光器。该激光器利用由单模-多模-单模光纤组成的滤波器实现波长可调谐及激光器的全光纤结构。该滤波器将多模光纤缠绕在偏振控制器上,两端分别与一段单模光纤相连,通过调整偏振控制器的状态,实现了中心波长1542～1560nm的不同激光输出。单波长连续可调谐激光器的波长可调范围为18nm,边模抑制比大于40dB,3dB线宽为0.096nm;进一步调整偏振控制器的状态和抽运功率,实验同时得到了连续可调谐的双波长、三波长等多波长激光输出。对于可调谐的多波长激光器,通过调整偏振控制器的状态,可实现波长间隔及输出中心波长两者可调。     

All-Optical Clock Recovery from NRZ-DPSK Signals at Flexible Bit Rates

We propose and demonstrate all-optical clock recovery （OR） from nonreturn-to-zero differential phase-shift- keying （NRZ-DPSK） signals at different bit rates theoretically and experimentally. By pre-processing with a single optical filter, clock component can be enhanced significantly and thus clock signal can be extracted from the preprocessed signals, by cascading a OR unit with a semiconductor optical amplifier based fibre ring laser. Compared with the previous preprocessing schemes, the single filter is simple and suitable for different bit rates. The clock signals can be achieved with extinction ratio over lOdB and rms timing jitter of 0.86 and 0.9 at 10 and 20 Gb/s, respectively. The output performances related to the bandwidth and the detuning of the filter are analysed. By simply using a filter with larger bandwidth, much higher operation can be achieved easily.     

Switchable and tuneable multi-wavelength Er-doped fibre ring laser using Sagnac filters

We demonstrate experimentally a simple configuration to perform wavelength-tuning and multi-wavelength operation in a fibre ring laser that is composed of an Erbium-doped fibre and includes a fibre-optic Sagnac interferometer as a spectral filter. We consider three different Sagnac filters including a 3 dB coupler, two wave retarders (WRs) and respectively 7 cm, 1 and 7 m of high birefringence fibre. The transmission spectrum of each filter is sinusoidal with a 70, 6, and 0.85 nm period, and its maxima can be shifted over one period by adjusting the angle of the retarders in the loop. By adjusting the WRs included in the filter and in the laser ring, tuneable single wavelength and several two- or three-wavelength lasing regimes were observed. In particular, fine adjustments of the WRs allow observing two- and three- wavelength operation with wavelength separations well below the homogeneous bandwidth of the gain medium. The stability of these modes of operation however strongly depends on environmental conditions at room temperature.     

Multiwavelength Dispersion-Tuned Actively Mode-Locked Erbium-Doped Fibre Ring Laser with Gain Competition Suppression

Multiwavelength dispersion-tuned actively mode-locked erbium-doped fibre ring laser is demonstrated by incorporating a section of highly nonlinear fibre （HNLF） in the laser cavity. The HNLF and the time gate element （modulator） in the fibre laser successfully suppress the gain competition in the erbium-doped fibre, and thus enable multiwavelength operation. Simultaneous generation of 10 GHz pulses up to eight different wavelengths is achieved. Wavelength, spacing and modes number tuning are investigated by changing fibre cavity length, dispersion, and erbium-doped fibre amplifier power, respectively.     

Spectrum control and shaping of optical pulses in optical fibre interferometers

This paper discusses the use of single-mode fibre ring interferometers for injection laser line narrowing and for enhancement of optical emission power. The efficient launching into fibre ring interferometers of multi-frequency external cavity injection laser emission, in both the c.w. and mode-locking regime, has been achieved. Matching the optical lengths of the external cavity and fibre interferometer allowed the measurement of mode width of such a laser. A method is proposed for shaping optical pulses in fibre ring interferometers from constant intensity frequency modulated emission. The mode-locking regime of all-fibre external cavity injection lasers has been achieved.     

基于半导体纳米线和金属脊的混合表面等离子体波导模式特性分析

波长可开关光纤激光器可以选择多波长光纤激光器中的一个或多个波长输出,支持光网络中多个波长的动态分配,适应现代光纤通信系统信道数越来越多的波分复用和密集波分复用的发展方向.本文提出并实现了一种自激发多波长可开关掺铒光纤激光器.该激光器通过一个980 nm泵浦进行抽运,使用掺铒光纤作为增益介质,产生1 550 nm光谱,并通过一个环形结构返回,从而实现自激发的过程,降低了实验成本.实验使用一个含有两段保偏光纤的Sagnac环作为滤波器.通过调整Sagnac环形滤波器内偏振控制器的角度,改变Sagnac环形滤波器的腔内增益,可以让光纤光栅反射出来的波长选择性通过,从而实现波长的开关功能.实验证明,通过调整Sagnac滤波器的腔内增益而让多波长选择性通过,是一种有效的实现波长可开关功能的方法.     

Harmonic Mode-Locked Ytterbium-Doped Fibre Ring Laser

We demonstrate a harmonic mode-locked ytterbium-doped fibre ring laser, which consists of a polarization-sensitive isolator, two polarization controllers, two 976nm laser diodes as the pump source and a two-segment ytterbium-doped fibre. Utilizing an additive pulse mode-locked technique based on nonlinear polarization evolution, the ytterbium-doped fibre laser can operate in mode-locked state by adjusting the position of polarization controllers. The cavity fundamental repetition rate is 23.78 MHz. We also observe the second- and third-harmonic mode locking in the normal dispersion region, and their repetition rates are 47.66 MHz and 71.56 MHz, respectively. Over-driving of the saturable absorber in the harmonic mode-locking pulse is analysed and discussed in detail.     

基于两滤波器级联和饱和吸收体的单纵模双波长光纤激光器

提出和证实了一种光纤环形激光器. 将一个带通滤波器与一个带阻滤波器级联,用一段保偏掺铒光纤作为饱和吸收体,得到了一种单纵模双波长光纤激光器. 结果表明,该激光器波长间隔为0.4 nm,边模抑制比大于49 dB.如果将两个波长进行差拍,该激光器有潜力得到49.85 GHz的微波信号.     

Tunable erbium doped fiber ring laser using fiber Bragg grating-assisted add-drop filter

A stable and low costless tunable erbium doped fiber ring laser using fiber Bragg grating-assisted add-drop filter is proposed and demonstrated. A stable laser output is obtained with a 4 nm tuning range. The power fluctuation, full-width at half maximum and SMSR are measured to be less than 0.50 dB, smaller than 0.015 nm and better than 55 dB in this tuning range.     

Semiconductor optical amplifier based swept wavelength source at 1060 nm using a scanning Fabry-Perot filter and an YDFA-based booster amplifier

We demonstrate a tuneable laser operating in the 1-1.1 μm wavelength region with a tuning range of 43 nm (FWHM), an output power of 19 mW and coherence length of 14 mm. The source is based on a master laser consisting of a cavity tuned ring configuration with a fibre Fabry-Perot filter used as a tuning element and a semiconductor amplifier as gain medium. The output of the master laser is subsequently power boosted using an Ytterbium doped fibre amplifier (YDFA). In addition to providing a power boost, we demonstrate that by tailoring the gain spectrum of the YDFA it is possible to increase the FWHM scanning range by 7 nm compared to that of the master laser.     

Self-Starting Passively Mode-Locked Er^3＋/Yb^3＋ Codoped Phosphate Glass All-Fibre Ring Laser

A self-starting, passively mode-locked all-fibre ring laser based on the homemade Er^3＋/Yb^3＋ codoped phosphate glass fibre is reported. Dual-pump sources were used to achieve the mode-locked operation in the experiment. The fundamental mode-locked pulse repetition rate is 10.67MHz. The pulse duration, assumed as the fit of hyperbolic secant pulse shape, is 5.82ps. We also observe the multi-pulse output of the fibre laser.     

60-GHz Band Dual-Mode Microstrip Ring Resonator Bandpass Filter Using Micromachining Technology

A new compact millimeter-wave dual-mode ring resonator bandpass filter is proposed. This filter has a 15% bandwidth at 58 GHz with 3.4 dB insertion loss. Input/output lines and ring resonator are directly connected to obtain tight coupling, and an open-end stub is inserted for dual-mode operation. This filter is fabricated on a GaAs wafer by using MEMS technology and can be applied for the millimeter- wave SoC.     

Single Mode Er-Doped π-Phase-Shifted Distributed Feedback Fibre Grating Laser

A novel method incorporating the shielded method and the post-processing method has been proposed to fabricate the π-phase-shifted fibre grating. Then an Er-doped π-phase-shifted distributed feedback fibre grating laser has been fabricated using the grating. The laser threshold is 20mW. When pumped with 90mW light at 980nm, the laser gives an output of 1.1mW. Its signal-to-noise ratio is better than 60dB. It is demonstrated that the laser is single mode operation by means of a Fabry--Perot scanning interferometer.