新型氧化铝模板自组装制备非晶碳纳米点阵列膜及其场发射性能研究

通过对阳极氧化铝(AAO)模板进行特殊扩孔处理,消除了AAO模板中带电阴离子对沉积碳离子的不良影响,利用磁过滤阴极弧等离子体沉积技术成功制备了非晶碳纳米尖点阵列膜.场发射扫描电镜(FESEM)分析表明,经过氧化和扩孔多步处理制备的AAO模板具有特殊的开口结构,制备的非晶碳纳米尖点阵列完整地复制了AAO模板的孔道阵列结构,纳米点排列整齐有序,直径约100nm,密度达1010cm-2,样品的场发射测试显示,非晶碳纳米点阵列具有良好的电子发射性能,发射电流为10mA/cm-2时的阈值电场为3.7V/μm.     

催化剂对纳米非晶碳膜场发射性能的影响

利用微波等离子体增强化学气相沉积(MPECVD)法,在经处理的单晶硅衬底上沉积了纳米非晶碳薄膜.通过Raman、SEM、XRD表征,研究了催化剂对纳米非晶碳膜的生长速率及场发射性能的影响.结果表明,在制备纳米非晶碳膜时使用FeC13,作为催化剂可大幅提高其生长速率.在相同的制备条件下,与未加FeCl3催化剂制备的纳米非...     

激光晶化形成纳米硅材料的场电子发射性质研究

利用KrF准分子激光退火超薄非晶硅膜,并结合热退火技术制备了单层纳米硅薄膜并研究了薄膜的场电子发射性质.在晶化形成的纳米硅薄膜中可以观测到稳定的场电子发射现象,其开启电场从原始淀积的非晶硅薄膜的17V/μm降低到8.5V/μm,而场发射电流密度可以达到0.1mA/cm².激光晶化后形成的纳米硅材料的场电子发射特性的改善可以从薄膜表面形貌的改变以及高密度纳米硅的形成所导致的内部电场增强作用来解释. 关键词： 纳米硅 场发射 激光晶化     

氧化锌纳米线的紫外光耦合增强场电子发射特性

本文采用热化学气相沉积方法制备氧化锌纳米线阵列, 研究氧化锌纳米线阵列在紫外光辐照下的场电子发射特性. 实验结果表明, 在紫外光辐照下, 氧化锌纳米线场发射开启电压降低, 发射电流明显增大. 机理分析认为, 氧化锌纳米线紫外光增强的场发射源自场电子发射与半导体耦合作用, 紫外光激发价带电子跃迁到导带和缺陷能级使发射电子数量增加, 同时, 光生电子发射降低了发射材料表面的有效功函数, 从而显著增强场电子发射性能. 氧化锌纳米线具有紫外光耦合增强场电子发射特性, 在光传感、冷阴极平板显示和场发射电子源等方面具有潜在的应用价值.     

非晶金刚石薄膜的场致电子发射性能研究

利用真空磁过滤弧沉积技术制备出一种高sp³含量的非晶碳膜———非晶金刚石薄膜，并对这种非晶金刚石薄膜的场电子发射特性及其发射机理进行了研究．实验结果表明，在阈值电场低于20V/μm情况下，得到的场发射电流达20—40μA，薄膜的电子发射行为符合Fowler-Nordheim场发射理论．研究表明，这种非晶金刚石薄膜具有负的电子亲合势和较小的有效功函数以及相对较低的禁带宽度 关键词：     

金刚石镶嵌非晶碳膜表面形貌对场致电子发射的影响

用微波等离子体化学气相沉积设备，在经过不同研磨预处理的金属钼衬底上沉积出了表面形貌有较大差异的金刚石镶嵌非晶碳膜，分别用扫描电子显微镜（ＳＥＭ）、金相显微镜和Ｘ射线衍射谱（ＸＲＤ）以及Ｒａｍａｎ光谱对样品进行了分析测试．研究了各样品的场致电子发射特性，结果发现薄膜表面由大量镶嵌有金刚石小晶粒的非晶碳球组成，在我们的实验范围内，薄膜表面非晶碳球尺寸越小，场致电子发射效果越好     

氧化锌纳米棒场发射性能研究

采用简单物理气相沉积法制备出取向和非取向的氧化锌纳米棒，他们的场致电子发射性能测量结果表明，ZnO纳米棒具有较好的场发射性能，但是高度取向的ZnO纳米棒阵列并不利于获得高的场致电子发射电流密度.这可能是由于高密度ZnO纳米棒之间具有较高的屏蔽效应，降低了ZnO纳米棒阵列的场放大因子，从而影响了其场发射性能.相反，非取向ZnO纳米棒由于相互之间的屏蔽效应比较弱，而且表面存在容易成为发射中心的微小突起，表现出较好的场发射效果.这些结果不仅有助于加深我们对准一维纳米材料场致电子发射性能的理解，也为未来场发射电子器件的实际应用提供了可靠的依据. 关键词： 氧化锌 场发射 非取向     

类球状微米金刚石聚晶膜场发射的稳定性

在覆盖金属钛层的陶瓷上,利用微波等离子体化学气相沉积(MPCVD)法制备出类球状微米金刚石聚晶膜。通过二极管结构测试了聚晶膜的场致电子发射特性,利用扫描电子显微镜、拉曼光谱、XRD分析了场发射前后薄膜的结构和表面形貌的变化。发现在高场、大电流密度的场发射中,对类球状微米金刚石聚晶薄膜中的金刚石聚晶颗粒影响很小,而对金刚石聚晶颗粒间的非晶碳层影响很大。对类球状微米金刚石聚晶变化机理进行了研究。     

碳纳米管/硅纳米孔柱阵列的场发射性能

"通过热化学气相沉积的方法将碳纳米管生长到硅纳米孔柱阵列衬底上．采用场发射扫描电子显微镜、透射电子显微镜、高分辨透射电子显微镜、拉曼光谱和X射线能谱对所制备的样品形貌、组成进行了分析．结果发现：所制备产物为一种具有面积大、准周期性的碳纳米管/硅巢状阵列复合结构．能谱分析表明碳纳米管仅含有碳元素．对样品进行场发射性能测试表明该结构开启电压为1.3 MV/m,当外加电压为4.26 MV/m,发射电流为5 mA/cm2．由FN公式计算相应的场增强因子约为1.1￡104．碳纳米管/硅纳米孔柱阵列好的场发射性能被归     

沉积时间对球状微米金刚石聚晶结构的生长及其场发射特性影响

利用微波等离子体化学气相沉积法,在覆盖金属钛层的陶瓷衬底上,通过改变沉积时间制备出不同结构的类球状微米金刚石聚晶碳膜.通过扫描电子显微镜、喇曼光谱、X射线衍射谱对碳膜进行了分析测试,并研究了不同沉积时间下沉积的类球状微米金刚石聚晶薄膜的场致电子发射特性.结果显示:不同的沉积时间所制备的碳膜形貌有很大变化,场致电子发射的效果也有很大不同,从而得出了场增强因子的降低和导电通道的增长是场发射效果变差的主要原因.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.