Functionalized polymers I. Poly(dichloroalkyl itaconates), synthesis and solution properties

The synthesis of poly(di-2-chloroethyl itaconate) (PD2CEI) and poly(di-3-chloropropyl itaconate) (PD3CPI) was carried out. The dilute solution behaviour of these polymers in tetrahydrofuran and chloroform at 298 K has been studied, by viscometry, membrane osmometry, and size-exclusion chromatography (SEC) measurements. The Kuhn-Mark-Houwink-Sakurada relationships were established. The flexibility factors σ and C_∞ and the thermodynamic parameters B were calculated using the Stockmayer-Fixman equation. The results obtained are compared with those found for the corresponding poly(methacrylates) and the poly(dialkyl itaconates), and discussed in terms of specific influence of the chlorine incorporated in the side chain.     

含茋生色团聚醚的合成与热致液晶行为

β 氯乙基缩水甘油醚 (GCE)和GCE/羟丁基乙烯基醚 (HBVE)分别通过阳离子聚合、光引发共聚合 ,获得两种聚醚 ,然后再分别与 4 硝基 4′ 羟基 (NHS)反应 ,制备了两种侧链含生色团的液晶聚合物(PSEG、PSV) .用FTIR、1H NMR和EA对其化学结构及生色团含量进行了表征 ,以POM、DSC、TGA和WAXD对聚合物介晶相转变温度、织构、热稳定性及相行为进行了研究 .结果表明 ,这类聚合物属向列型热致双向性液晶 ,液晶相转变温度较低、范围较宽 ;聚合物热稳定性较好 ,开始分解温度在 30 0℃以上 .     

聚(β-氯乙基缩水甘油醚)的合成及其酯化反应动力学

本文合成了β-氯乙基缩水甘油醚及其聚合物。结果表明, AlEt3-0.5H2O体系是β-氯乙基缩水甘油醚的一种有效的聚合引发剂。研究了聚(β-氯乙基缩水甘油醚)的酯化反应动力学, 并通过^1H NMR和IR光谱确立了酯化度的计算关系式。最后, 通过光交联的动力学研究发现, 酯化聚合物中的肉桂酰基含量为85%时, 材料的感光灵敏度最高。     

Correlation of thermal degradation mechanisms: Polyacetylene and vinyl and vinylidene polymers

The thermal degradation of poly(vinyl bromide) (PVB), poly(vinyl chloride) (PVC), poly(vinyl alcohol) (PVA), poly(vinyl acetate) (PVAc), poly(vinyl fluoride) (PVF), poly(vinylidene chloride) (PVC₂), and poly(vinylidene fluoride) (PVF₂) has been studied by direct pyrolysis–mass spectrometry (DP-MS) and flash pyrolysis–gas chromatography–mass spectrometry techniques. Vinyl and vinylidene polymers exhibit two competitive thermal degradation processes: (1) HX elimination with formation of polyene sequences which undergo further moleculaar rearrangements, and (2) main-chain cleavage with formation of halogenated or oxigenated compounds. The overall thermal degradation process depends on the prevailing decomposition reaction in each polymer; therefore, different behaviors are observed. The thermal degradation of polyacetylene (PA) has also been studied and found important for the elucidation of the thermal decomposition mechanism of the title polymers.     

Miscibility of Halogen-containing Polymethacrylates with Various Poly(alkyl acrylate)s

The miscibility behavior of a series of halogen-containing polymethacrylates with poly(methyl acrylate), poly(ethyl acrylate), poly(n-propyl acrylate) and poly(n-butyl acrylate) was investigated by differential scanning calorimetry and for lower critical solution temperature (LCST) behavior. Poly(chloromethyl methacrylate), poly(1-chloroethyl methacrylate), poly(2-chloroethyl methacrylate), poly(2,2-dichloroethyl methacrylate), poly(2,2,2-trichloroethyl methacrylate), poly(2-fluoroethyl methacrylate) and poly(1,3-difluoroisopropyl methacrylate) are miscible with some of the poly(alkyl acrylate)s. Most of the miscible blends show LCST behavior. However, poly(3-choloropropyl methacrylate), poly(3-fluoropropyl methacrylate), poly(4-fluorobutyl methacrylate), poly(1,1,1,3,3,3-hexafluoroisopropyl methacrylate), poly(2-bromoethyl methacrylate) and poly(2-iodoethyl methacrylate) are immiscible with any of the poly(alkyl acrylate)s studied. © 1997 John Wiley & Sons, Ltd.     

The thermal degradation of poly(diethyl fumarate)

The kinetics and mechanism of the thermal degradation of poly(diethyl fumarate) (PDEF) were studied by thermogravimetry, as well as by analysis of the thermolysis volatiles and polymer residue. The characteristic mass loss temperatures were determined, as were the overall thermal degradation activation energies of three PDEF samples of varying molar mass. Ethylene and ethanol were present in the thermolysis volatiles at degradation temperatures below 300 °C, while diethyl fumarate was also evidenced at higher degradation temperatures. The amount of monomer increased with increasing degradation temperature. The dependence of the molar mass of the residual polymer on the degradation time and temperature was established and the number of main-chain scissions per monomer unit, s/P₀, calculated. A thermal degradation mechanism including de-esterification and random main-chain scission is proposed. The thermal degradation of PDEF was compared to the thermolysis of poly(ethyl methacrylate) (PEMA), poly(diethyl itaconate) (PDEI) and poly(ethyl acrylate) (PEA).     

Pyrolysis of poly(2-propylheptyl acrylate)

The thermal destruction processes of poly(2-propylheptyl acrylate) take place at the range of temperature 250–950 °C was investigated using pyrolysis–gas chromatography. Knowledge of the types and amounts of pyrolysis products will provide important information about the thermal degradation of homopolymer poly(2-propylheptyl acrylate) and the mechanisms involved. Unsaturated monomers 2-propylheptyl acrylate and 2-propylheptyl methacrylate, according to by-product alkyl alcohol 2-propylheptylalcohol, alkene 2-propylheptene-1, carbon dioxide, carbon monoxide, methane, and ethane were formed during thermal degradation of poly(2-propylheptyl acrylate).     

Thermal degradation of poly(alkyl methacrylates)

The thermal degradation of selected poly(alkyl methacrylates) at temperatures between 300 and 800 °C was investigated by pyrolysis gas chromatography. Quantitative characterization of the pyrolysis products yields insights into the mechanism for thermal degradation of poly(alkyl methacrylates) under these conditions. Unsaturated monomeric alkyl methacrylates, carbon dioxide, carbon monoxide, methane, ethane, methanol, ethanol, and propanol were formed during thermal degradation of poly(alkyl methacrylates).     

Thermal degradation of bromine-containing polymers. Part 3—Blends of poly(2-bromoethyl methacrylate) and poly(methyl acrylate)

Films of a blend of equal weights of poly(2-bromoethyl methacrylate) (P2BEM) and poly(methyl acrylate) (PMA) were prepared by evaporation of a solution in acetone. The principal characteristics and products of the thermal degradation of the blend were established by the application of thermal analysis and infra-red and mass spectrometric techniques. Similarities to the degradation behaviour of copolymers of 2-bromoethyl methacrylate (2BEM) and methyl acrylate (MA) were noted.     

Thermal degradation of poly(vinylpyridine)s

The thermal stability and the temperature at which maximum degradation yields are detected were quite similar for both poly(2-vinylpyridine) (P2VP) and poly(4-vinylpyridine) (P4VP). However, considerable differences among the thermal degradation products of both polymers were detected indicating a correlation between the polymer structure and the degradation mechanism. Direct pyrolysis mass spectrometry analyses revealed that P2VP degrades via a complex degradation mechanism, yielding mainly pyridine, monomer, and protonated oligomers, whereas depolymerization of P4VP takes place in accordance with the general thermal behaviour of vinyl polymers. The complex thermal degradation behaviour for P2VP is associated with the position of the nitrogen atom in the pyridine ring, with σ-effect.     

The degradation mechanism using TG-MS technique of some aromatic polyethers containing flexible spacers

The paper presents a thermogravimetric study of some aromatic poly- and copolyethers, using mass spectrometry technique combined with thermogravimetric analysis. The polymers were synthesized by phase transfer catalysis technique, using bis(2-chloroethyl)-ether or 1,6-dichlorohexane as flexible spacers and various bisphenols (4,4'-dihydroxydiphenyl, 4,4'-dihydroxyazobenzene and bisphenol A). The presence of azobenzenic moieties in the chain induces a liquid crystalline behavior, but, due to the high values of the transition temperature, some precautions during the thermal characterisation are necessary. In the case of azobenzenic samples, the degradation reactions begin, as a function of the chemical structure, around 230-250°C. A degradation mechanism based on chain transfer reactions was proposed. The chain flexibility influences the thermal degradation mechanism, in the case of rigid polymers the chain transfer reactions being less probable. For the flexible chains, the thermal stability is not essentially influenced by the copolymerisation ratio between the two aromatic bisphenols. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermal degradation of partly complexed poly(vinylpyridines) with transition metal chloride

The thermal degradation of poly(vinylpyridines), partly complexed with transition metal chlorides containing Co(II), Ni(II), Cu(II) and Zn(II) ions, was investigated using thermogravimetry, infrared spectrometry and gc/mass spectrometry. When poly(2-vinylpyridine) and poly(4-vinylpyridine) were partly complexed with transition metal ions, thermal degradation was initiated at low temperature. The complexes were decomposed even near the threshold temperature for weight loss. Degradations were modified by the complexation, particularly for poly(2-vinylpyridine). Yields of dimers, ethylpyridine, etc., increased linearly with degree of complexation, but that of monomer decreased linearly. The increase of the yield of dimer could be explained from the concept that polymer radicals reacted with metal chlorides, then dehydrochlorinated and underwent β-scission.     

Morphology and thermal degradation studies of melt-mixed poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) biodegradable polymer blend nanocomposites with TiO2 as filler

The morphology and thermal stability of melt-mixed poly(lactic acid) (PLA)/poly(ε-caprolactone) (PCL) blend nanocomposites with small amounts of TiO₂ nanoparticles were investigated. The nanoparticles were mostly located in the PLA phase, with good dispersion of individual particles, although significant aggregation was also visible. The thermal stability and degradation behaviour of the different samples were studied using thermogravimetric analysis (TGA) and TGA-Fourier-transform infrared (FTIR) spectroscopy. Neat PCL showed better thermal stability than PLA, but the degradation kinetics revealed that PLA had a higher activation energy of degradation than PCL, indicating its degradation rate more strongly depends on temperature, probably because of a more complex degradation mechanism based on chain scission and re-formation. Blending of PLA and PCL reduced the thermal stabilities of both polymers, but the presence of TiO₂ nanoparticles improved their thermal stability. The nanoparticles also influenced the volatilization of the degradation products from the blend, acted as degradation catalyst and/or retarded the escape of volatile degradation products.     

The thermal susceptibility of poly(chloroethyl methacrylates)

The non-oxidative thermal degradation kinetics and mechanism of poly(2-monochloro, 2, 2-dichloro and 2, 2, 2, -trichloroethyl methacrylates) were studied. The influence of the antioxidant IRGA-NOX 1010 on the thermal degradation of the monochloroethyl derivative was also investigated. Initial hydrolysis data on the major degradation products, the corresponding monomers, were obtained.     

Thermal degradation of poly(olefin sulphone)s. Part I—The effect of olefin structure on the yields of volatile products

The rates and mechanisms of the thermal degradation of nine alternating poly(olefin sulphone)s with different olefin structures have been investigated at 150°C and 200°C by a novel technique which is particularly suitable for studying the initial steps of the degradation. Rapid degradation was initiated at the CS bond with depolymerisation to sulphur dioxide and olefin. The rate of thermal degradation showed a moderate correlation with the ceiling temperature for monomer-polymer equilibrium and also with the number of β-hydrogen atoms, but neither parameter provided an adequate measure of the sensitivity of all the poly(olefin sulphone)s to thermal degradation. Substantial isomerisation was observed in the formation of olefin from poly(3-methyl-1-butene sulphone).     

Chemical oxidative polymerization of m-phenylenediamine and its derivatives using aluminium triflate as a co-catalyst

Aromatic diamine monomers, including m-phenylenediamine (mPD), 2-methyl-m-phenylenediamine (2Me-mPD), 4-methyl-m-phenylenediamine (4Me-mPD) and trimethyl-m-phenylenediamine (tMe-mPD), were polymerized by chemical oxidation using ammonium persulfate as an oxidant. Aluminium triflate (Al(OTf)₃) was also used for the first time as a co-catalyst under various polymerization conditions. The polymerization yield was improved when Al(OTf)₃ was introduced to the polymerization reaction for most polymers. The poly(2-methyl-m-phenylenediamine) (P(2Me-mPD)), poly(4-methyl-m-phenylenediamine) (P(4Me-mPD)) and poly(trimethyl-m-phenylenediamine) (P(tMe-mPD)) polymers exhibited better solubility than poly(m-phenylenediamine) (P(mPD)) polymers in most common solvents. The homopolymers obtained were characterized by FT-IR, ¹H and ¹³C NMR, WAXD and TGA. The results showed that the yield, solubility and structure of the polymers are significantly dependent on the polymerization conditions. TGA measurements indicated that the polymers have good thermal stability and decompose above 400 °C in nitrogen.     

Preparation and Characterization of Head-to-Head Polymers. III. Head-to-Head Poly (methyl Crotonate)

Alternating copolymers of cis-butene-2 and maleic anhydride were esterfied to the methylester which corresponds to head to head (H-H) poly(methyl crotonate).

The chemical, physical, and mechanical properties and thermal degradation behavior of H-H poly (methyl crotonate) was studied and compared with the properties of head to tail (H-T) poly(methyl crotonate). This latter polymer was made by a known anionic polymerization technique and was, unlike the amorphous H-H polymer, partially crystalline. The T_g of H-H polymer was found to be higher than that of the H-T polymer. Thermal degradation behavior of H-H and H-T polymer was between the degradation behavior of H-H and H-T poly(methyl cinnamate) and poly (methyl acrylate). Poly (methyl crotonates) degraded to a substantial part to small molecules and char; methyl crotonate was found among the degradation products. H-H Poly (methyl crotonate) gave also butene-2 and a mixture of dimethyl maleate and dimethyl fumarate on pyrolysis.     

Characterization and degradation of the poly(methylphenylsiloxane)–poly(methyl methacrylate) graft copolymer

Poly(methylphenylsiloxane)–poly(methyl methacrylate) graft copolymers (PSXE-g-PMMA) were prepared by condensation reaction of poly(methylphenylsiloxane)-containing epoxy resin (PSXE) with carboxyl-terminated poly(methyl methacrylate) (PMMA), and they were characterized by gel permeation chromatography (GPC), infrared (IR), and ²⁹Si and ¹³C nuclear magnetic resonance (NMR). The microstructure of the PSXE-g-PMMA graft copolymer was investigated by proton spin–spin relaxation T₂ measurements. The thermal stability and apparent activation energy for thermal degradation of these copolymers were studied by thermogravimetry and compared with unmodified PMMA. The incorporation of poly(methylphenylsiloxane) segments in graft copolymers improved thermal stability of PMMA and enhanced the activation energy for thermal degradation of PMMA. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2521–2530, 1998     

Thermal degradation of two different polymers bearing amide pendant groups prepared by ATRP method

Piperidinocarbonylmethyl methacrylate (PyCMMA) and 1-(piperidinocarbonyl) ethylmethacrylate (PyCEMA) monomers were synthesized. Polymerizations of PyCMMA and PyCEMA were carried out by atom transfer radical polymerization. The structure of monomers and polymers was characterized by ¹H-NMR, ¹³C-NMR, and FT-IR spectroscopies. Characterization of poly(PyCMMA) and poly(PyCEMA) were carried out using differential scanning calorimetry and gel permeation chromatography. The experimental results showed that the reaction exhibited characteristics of controlled polymerization. The thermal degradation behaviors of poly(PyCEMA) and poly(PyCMMA) were studied using thermogravimetry and a single line vacuum system consisting of a degradation tube with a condenser for product collection. The poly(PyCEMA) and poly(PyCMMA) were heated from ambient temperature to 325 and 500 °C, respectively. The products of degradation were collected as a cold ring fraction (CRF). The CRFs of degradation were investigated by means of IR, ¹HNMR, and GC-MS. For the degradation of both polymers, the major products of CRFs are piperidinocarbonyl methanol and 1,2-dipiperidino,1-oxo ethane. The GC-MS, IR, and NMR data showed that depolymerization below 325 °C to the corresponding monomer was not prominantin the thermal degradation of poly(PyCMMA). The mode of thermal degradation including formation of the major products was identified.     

Thermal decomposition of copolymers from ethylene with some vinyl derivatives

The thermal degradation of ethylene-vinyl acetate (EVA), ethylene-vinyl-3,5-dinitrobenzoate (EVDNB) and ethylene-vinyl alcohol (EVAL) copolymers have been studied using differential thermal analysis (DTA) and thermogravimetry (TG) under isothermal and dynamic conditions in nitrogen. Thermal analysis indicates that EVA copolymers are thermally more stable than EVDNB samples. The degradation of the copolymers considered occurs as an additive degradation of each component polyethylene (PE) and poly(vinyl acetate) (PVA), poly(vinyl-3,5-dinitrobenzoate) (PVDNB) or poly(vinyl alcohol) (PVAL). The apparent activation energy of the decomposition was determined by the Kissinger and Flynn-Wall methods which agree well.