Ni-Co-TiO2 nanocomposite coating prepared by pulse and pulse reversal methods using acetate bath

Ni-Co/nano TiO₂ (Ni-Co-TiO₂) composite coatings were prepared under pulse current and pulse reverse current methods using acetate bath. The microstructure and corrosion resistance of the coatings were characterized by means of XRD, SEM and EIS. Both the Ni-Co alloy and composite coatings exhibited single phase of Ni matrix with face centered cubic (fcc) crystal structure. The crystal orientation of the Ni-Co-TiO₂ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with Ni-Co alloy coatings. The results showed that the microstructure and performances of the coatings were greatly affected by TiO₂ content on the deposits prepared by PC and PRC methods. The microhardness and corrosion resistance were enhanced in the optimum percentage of TiO₂ composite coatings. The PRC composite coatings were exhibited from compact surface, higher microhardness and good corrosion resistance compared with that of the PC composite coating.     

Physical and electrochemical characterizations of Ni-SiO2 nanocomposite coatings

Advances in materials performance often require the development of composite system. In the present investigation, SiO₂-reinforced nickel composite coatings were deposited on a mild steel substrate using direct current electrodeposition process employing a nickel acetate bath. Surface morphology, composition, microstructure and crystal orientation of the Ni and Ni-SiO₂ nanocomposite coatings were investigated by scanning electron microscope, energy dispersive X-ray spectroscopy and X-ray diffraction analysis, respectively. The effect of incorporation of SiO₂ particles in the Ni nanocomposite coating on the microhardness and corrosion behaviour has been evaluated. Smooth composite deposits containing well-distributed silicon oxide particles were obtained. The preferred growth process of the nickel matrix in crystallographic directions <111>, <200> and <220> is strongly influenced by SiO₂ nanoparticles. The average crystallite size was calculated by using X-ray diffraction analysis and it was ~23 nm for electrodeposited nickel and ~21 nm for Ni-SiO₂ nanocomposite coatings. The crystallite structure was fcc for electrodeposited nickel and Ni-SiO₂ nanocomposite coatings. The incorporation of SiO₂ particles into the Ni matrices was found to improve corrosion resistance of pure Ni coatings. The corrosion potential (E _corr) in the case of Ni-SiO₂ nanocomposite coatings had shown a negative shift, confirming the cathodic protective nature of the coating. The Ni-SiO₂ composite coatings have exhibited significantly improved microhardness (615 HV) compared to pure nickel coatings (265 HV)     

Zn-ZrO2 nanocomposite coatings: Elecrodeposition and evaluation of corrosion resistance

The Zn and Zn-ZrO₂ composite coatings were produced by electrodeposition technique using sulphate bath. ZrO₂ particles were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The ZrO₂ particle size distribution in the plating bath and Zeta potential and the ZrO₂ were measured using dynamic light scattering technique (DLS). The corrosion resistance properties of Zn and Zn-ZrO₂ composite coatings were compared by examining the experimental data acquired through polarization, open circuit potential (OCP) and Tafel measurements. The corrosion environment was 3.5 wt% NaCl solution. The variation of amount of ZrO₂ in the solution on their % wt inclusion in the composite and on composite microhardness was investigated. XRD patterns were recorded for Zn and Zn-ZrO₂ coatings to compare their grain size. The SEM images of coatings before and after corrosion under chemical and electrochemical conditions were presented. The results were analyzed to establish the superiority of Zn-ZrO₂ composite over Zn coating.     

Electrodeposition and tribological properties of Ni-SrSO4 composite coatings

Ni-SrSO₄ composite coatings were electrodeposited on superalloy Inconel 718 from a Watts electrolyte containing a SrSO₄ suspension. Ni-SrSO₄ coatings were investigated by scanning electron microscope, microhardness tester, and friction and wear tester in sliding against a bearing steel ball under unlubricated condition. The incorporation of SrSO₄ into Ni matrix increases the microhardness of electrodeposited coatings. Ni-SrSO₄ composite coating exhibits a distinctly low friction coefficient and a small wear rate as contrasted with pure Ni coating and the substrate. The effect of SrSO₄ particles on microstructure and tribological properties of Ni-SrSO₄ composite coatings is discussed.     

Surface modification of titanium by nano-TiO2/HA bioceramic coating

A nano-TiO₂/hydroxyapatite composite bioceramic coating was developed and applied to the surfaces of pure titanium discs by the sol-gel method. A TiO₂ anatase bioceramic coating was utilized in the inner layer, which could adhere tightly to the titanium substrate. A porous hydroxyapatite (HA) bioceramic coating was utilized in the outer layer, which has higher solubility and better short-term bioactivity. Conventional HA coatings and commercially pure titanium were used as controls. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed to characterize the crystallization, surface morphology, and thickness of the coatings. The bioactivities of the coatings were evaluated by in vitro osteoblast cultures. Results showed that the nano-TiO₂/HA composite bioceramic coating exhibited good crystallization and homogeneous, nano-scale surface morphology. In addition, the nano-TiO₂/HA coating adhered tightly to the substrate, and the in vitro osteoblast cultures exhibited satisfactory bioactivity.     

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique and conventional electroplating (CEP) technique from Watt's type electrolyte without any additives. The microstructure, hardness, and wear resistance of resulting composites were investigated. The results show that the incorporation of nano-Al₂O₃ particles changes the surface morphology of nickel matrix. The preferential orientation is modified from (2 0 0) plane to (1 1 1) plane. The microhardness of Ni-Al₂O₃ composite coatings in the SCD technique are higher than that of the CEP technique and pure Ni coating and increase with the increasing of the nano-Al₂O₃ particles concentration in plating solution. The wear rate of the Ni-Al₂O₃ composite coating fabricated via SCD technique with 10 g/l nano-Al₂O₃ particles in plating bath is approximately one order of magnitude lower than that of pure Ni coating. Wear resistance for SCD obtained composite coatings is superior to that obtained by the CEP technique. The wear mechanism of pure Ni and nickel nano-Al₂O₃ composite coatings are adhesive wear and abrasive wear, respectively.     

Electrodeposition and properties of Zn-nanosized TiO2 composite coatings

Nanosized TiO₂ particles were prepared by sol-gel method. The TiO₂ particles were co-deposited with zinc from a sulphate bath at pH 4.5 using electrodeposition technique. The corrosion behavior of the coatings was assessed by electrochemical polarization, impedance, weight-loss and salt spray tests. Wear resistance and microhardness of the composite coating was measured. The smaller grain size of the composite coatings was observed in the presence of TiO₂ and it was confirmed by the images of scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques.     

Fortification of Ni–Y<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite coatings prepared by pulse and direct current methods

Ni–Y₂O₃ nanocomposite coatings were prepared under direct current (DC) and pulse current (PC) using acetate bath. The microstructure and corrosion resistance of the coatings were characterized by means of XRD, SEM, AFM, and EIS. The results showed that the microstructure and performances of the coatings were greatly affected by Y₂O₃ content on the deposits prepared by DC and PC methods. The microhardness and corrosion resistance were enhanced in the optimum percentage of Y₂O₃ composite coatings. The PC composite coatings were exhibited compact surface, higher microhardness, and good corrosion resistance compared with that of the DC composite coatings.     

Effect of α-Al2O3 on the properties of cold sprayed Al/α-Al2O3 composite coatings on AZ91D magnesium alloy

Composite coatings using pure Al powder blended with α-Al₂O₃ as feedstock were deposited on AZ91D magnesium alloy substrates by cold spray (CS). The content of α-Al₂O₃ in the feedstock was 25 wt.% and 50 wt.%, respectively. The effects of α-Al₂O₃ on the porosity, microhardness, adhesion and tensile strength of the coatings were studied. Electrochemical tests were carried out in neutral 3.5 wt.% NaCl solution to evaluate the effect of α-Al₂O₃ on the corrosion behavior of the coatings. The results showed that the composite coatings possessed lower porosity, higher adhesion strength and tensile strength than cold sprayed pure Al coating. The corrosion current densities of the composite coatings were similar to that of the pure Al coating and much higher than that of bare AZ91D magnesium alloy.     

Friction and wear properties of the co-deposited Ni-SiC nanocomposite coating

Ni-SiC nanocomposite coatings were produced by electrodeposition from a nickel sulfate bath containing SiC nanoparticles with an average particle size of 30 nm. The characteristics of the coatings were assessed by scanning electron microscopy and microhardness test. The friction and wear performance of Ni-SiC nanocomposite coatings and Ni film were comparatively investigated sliding against Si₃N₄ ceramic balls under non-lubricated conditions. The results indicated that compared to Ni film, Ni-SiC nanocomposite coating exhibited enhanced microhardness and wear resistance. The effect of SiC nanoparticles on the friction and wear resistance is discussed in detail.     

The effect of powder preparation method on the corrosion and mechanical properties of TiN-based coatings by reactive plasma spraying

TiN-based composite coatings with and without the addition of Cr were deposited by reactive plasma spraying (RPS) in air. Both sintered and mixed powder of Ti and B₄C were used for the RPS process. A thermodynamic model was firstly used to estimate the complicated phase composition of composite coatings prepared by RPS. The phase composition, structures and properties of TiN-based coatings were investigated using XRD, SEM and a Vickers microhardness tester. The results show that the phases in TiN-based coatings do not generate according to priority of Gibbs free energy value due to non-equilibrium reactive course during thermal spraying. The coating deposited using sintered Ti and B₄C powder is composed of two main phases (TiN and TiN_0.3), two minor phases (Ti₂O₃ and TiB₂), and a small fraction of TiC phase. The composition of the coating deposited using the mixed powder with Cr added is predominantly in the TiN and TiB₂ phases, a smaller phase fraction of Ti₂O₃ and TiO₂, and some unreacted Cr. The Vickers microhardness of the coating deposited using sintered powder is higher than that of using mixed powder. The composite coating deposited using mixed powder with the addition of Cr shows superior corrosion resistant to that using sintered powder when tested in 3.5 wt.% NaCl electrolytic solution.     

The production of nickel–alumina composite coating via electroplating

A series of electroplating works have been conducted to investigate the best condition for the coelectrodeposition of nickel–alumina (Ni/α–Al₂O₃) composite coating. Co-electrodeposition was done onto mild steel as cathode at ambient temperature (27°C) with current density of 30 mA/cm² under α-Al₂O₃ concentration of 2 g/l and various agitation speeds of 50, 100, 150, 200, and 250 rpms. The cross-section of the composite coatings portrayed α-Al₂O₃ particles was co-deposited. Under field emission scanning electron microscopy analysis, the coating shows a coarse surface morphology, while cross-sectional microstructures shows a compact embedding of α-Al₂O₃ particle in the Ni matrix. Elemental analysis by EDX detected the presence of Ni and α-Al₂O₃. Vickers microhardness testing shows that the coating hardness increases almost 60% at the highest agitation speed, i.e., 250 rpm.     

Effect of NaAlO2 concentrations on microstructure and corrosion resistance of Al2O3/ZrO2 coatings formed on zirconium by micro-arc oxidation

In this study, Al₂O₃/ZrO₂ composite coatings were prepared on Zr substrates by micro-arc oxidation (MAO) in the NaAlO₂-containing electrolytes, and the effect of NaAlO₂ concentration on the microstructure, bond strength, microhardness and corrosion resistance of coatings was systematically investigated. The study reveals that the adequate NaAlO₂ in the electrolyte (>0.2 M) is essential to the formation of needle-like α-Al₂O₃ in the coatings, and the amount of α-Al₂O₃ rises with the increase of the NaAlO₂ concentration. m-ZrO₂ and t-ZrO₂ are present in all of the coatings, but their relative amount largely depends on the amount of Al₂O₃. It is also found that as the NaAlO₂ concentration increases from 0.2 to 0.3 M, the coating becomes denser and thicker, and its bond strength, maximum microhardness and corrosion resistance increases as well. The coating formed at 0.3 M NaAlO₂ demonstrates the highest bond strength of 52 MPa, the maximum microhardness of 1600 Hv_0.2N and the superior corrosion resistance. However, the overhigh concentration of NaAlO₂ (0.35 M) is found harmful to the coating's microstructure and properties.     

Preparation and characterization of the electrodeposited Cr-Al2O3/SiC composite coating

To increase the SiC content in Cr-based coatings, Cr-Al₂O₃/SiC composite coatings were plated in Cr(VI) baths which contained Al₂O₃-coated SiC powders. The Al₂O₃-coated SiC composite particles were synthesized by calcining the precursor prepared by heterogeneous deposition method. The transmission electron microscopy analysis of the particles showed that the nano-SiC particle was packaged by alumina. The zeta potential of the particles collected from the bath was up to +23 mV, a favorable condition for the co-deposition of the particles and chromium. Pulse current was used during the electrodeposition. Scanning Electron Microscopy (SEM) indicated that the coating was compact and combined well with the substrate. Energy dispersive X-ray analysis of Cr-Al₂O₃/SiC coatings demonstrated that the concentration of SiC in the coating reached about 2.5 wt.%. The corrosion behavior of the composite coating was studied by potentiodynamic polarization and electrochemical impedance spectroscopy techniques. The data obtained suggested that the Al₂O₃/SiC particles significantly enhanced the corrosion resistance of the composite coating in 0.05 M HCl solution.     

Effect of Ni-to-Fe ratio on structure and properties of Ni-Fe-B-Si-Nb coatings fabricated by laser processing

Ni-Fe-B-Si-Nb coatings have been deposited on mild steel substrates using high power laser cladding process followed by laser remelting. The influence of Ni-to-Fe concentration ratio in (Ni_100−xFe_x)₆₂B₁₈Si₁₈Nb₂ (x = 55, 50, 45 and 40) powders on the phase composition and microstructure is analyzed by X-ray diffraction, scanning- and transmission-electron microscopies. The microhardness and corrosion resistance properties of the coatings are also measured. The results reveal that amorphous matrix layers are obtained for all coatings. The increase of the Ni-to-Fe ratio can promote the formation of γ(Fe-Ni) phase and decrease the formation of Fe₂B phase and α-Fe phase. The coating with 1:1 ratio of Ni-to-Fe exhibits the highest microhardness of 1200 HV_0.5 and superior corrosion resistance property due to its largest volume fraction of amorphous phase in the coating. Higher or lower than 1:1 ratio of Ni-to-Fe may result in lower amorphous forming ability. However, even that the coating with ratio of 3:2, shows a minimum of microhardness, it shows a better corrosion resistance than other two coatings.     

Microstructure and corrosion properties of thick WC composite coating formed by plasma cladding

The thick Ni-coated WC coatings, in a matrix of Nickel-based alloys, were prepared on AISI 1045 steel using plasma cladding equipment. A pre-placed layer of uniform mixture, with different weight fractions of Ni-coated WC powder and Nickel-based alloy powder, on the steel substrate was melted at the high temperature of the plasma jet. The coating composition, microstructure and microhardness were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectrometer (EDS) and microhardness testing. The experimental results show that the metallurgical bond was formed between the coating and substrate. The XRD results show that the coatings contain γ-Ni, carbides (such as M₂₃C₆ and M₇C₃) and boride (such as Fe₂B, Fe₃B phases). SEM shows that all the coatings are crack-free with lower porosity (<1%). It is found that the microhardness and the electrochemical behavior of the coatings are depended on the content of Ni-coated WC powder. The corrosion mechanism for the coatings may be due to the microgalvance corrosion between the phases in the cladding coatings.     

Facile synthesis and electrochemical properties of a novel Ni-B/TiC composite coating via ultrasonic-assisted electrodeposition

A novel Ni-B/TiC composite coating was synthesized by ultrasonic-assisted direct current electrodeposition. Ultrasonic technology was adopted to prevent the agglomeration of nanoparticle, improve the structure and corrosion resistance, using an ultrasonic bath at frequency 40 KHz and acoustic power 300 W. The influences of current density and deposition time on its structure and electrochemical behaviors were studied. Under ultrasonic dispersion, the composite coatings are smooth, compact with protrusion structure sparsely distributed on it. The average roughness (S_a) was about 13.6–26.1 nm. The crystallite size is 10–21 nm. The preferred orientation is Ni (1 1 1) texture. EIS results indicated that the corrosion resistance was greatly improved by ultrasonic-assisted method. The corrosion mechanism is consistent with one-time constant EEC model of R_s(CPE_dlR_ct). With the increase of immersion time, the R_ct of the composite coating often first increased and then decreased. Under ultrasonic, current density 2 A dm⁻² and deposition time 20 min were the appropriate parameters for the optimal corrosion resistance and excellent long-term electrochemical stability in 3.5 wt% NaCl corrosive solution. This coating shows good application prospect for corrosion protection in aggressive environment.     

Development of electroless Ni-Zn-P/nano-TiO2 composite coatings and their properties

Ni-Zn-P-TiO₂ composite coatings were successfully obtained on low carbon steel by electroless plating technique. Deposits were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive analysis (EDS) studies. The hardness and microstructure of as plated and heat treated Ni-Zn-P and Ni-Zn-P-TiO₂ composite coatings were analyzed. The change in microstructure and higher hardness was noticed for heat treated composite. The corrosion resistance behavior of as plated and heat treated Ni-Zn-P and Ni-Zn-P-TiO₂ coatings was investigated by anodic polarization, Tafel plots and electrochemical impedance spectroscopic (EIS) studies in 3.5 wt% NaCl solution. The composite coating exhibited enhanced corrosion resistance property over Ni-Zn-P coating.     

电流密度对铝合金微弧氧化膜物理化学特性的影响

利用微弧氧化(MAO)技术，在LYl2铝合金上沉积了显微硬度达42.14GPa的超硬陶瓷膜.采用x射线衍射仪和显微硬度计研究了阳极电流密度j_a和阴极、阳极电流密度比j_c/j_a对MAO膜相构成和力学特性的影响.此外，利用扫描电子显微镜和恒电位仪分别对膜的微结构和抗点腐蚀特性进行了分析.结果表明，高j_a制备的膜主要含α-Al₂O₃相，低j_a制备的膜主要含γ-Al₂O₃相.显微硬度测试表明，这类膜有较高的硬度，但以j_a=15A/dm²和j_c/j_a=0.7制备的陶瓷膜硬度最高.抗点腐蚀测试表明，j_c/j_a对陶瓷膜的微结构有很强的影响. 关键词： 微弧氧化 显微硬度 电流密度 抗点腐蚀     

Atmospheric reactive plasma sprayed Fe-Al2O3-FeAl2O4 composite coating and its property evaluation

In the present study, Fe-Al₂O₃-FeAl₂O₄ composite coatings were successfully deposited by reactive plasma sprayed Al/Fe₂O₃ agglomerated powder. Phase composition and microstructure of the coatings were determined by XRD and SEM. The results indicated that the composite coatings were principally composed of three different phases, i.e. FeAl₂O₄ phase as main framework, dispersed ball-like Fe-rich phase, and small splats of Al₂O₃ phase, and it was thought that the in situ synthesized metal phase was helpful to toughen the coating matrix. According to the results of the indentation and frictional wear tests, the composite coating exhibited excellent toughness and anti-friction properties in comparison with conventional Al₂O₃ monophase coating, though its microhardness value was a little lower than that of Al₂O₃ coating. The formation mechanism and the toughening mechanism of the composite coating were clarified in detail.