Adsorption equilibrium at the metal-oxide film interface in the oxidation reactions of Ni,Cr, and their alloys

An adsorption thermodynamic model of the oxidation of Ni-Cr alloys is proposed. According to this model, the adsorption of the alloy component with a lower surface energy (Ni) at the alloy-oxide film interface shifts the equilibrium of the solid-phase reaction 3NiO + 2Cr = Cr₂O₃ + 3Ni (1) toward the enrichment of the oxide film in NiO. It was demonstrated that the total Gibbs energy change for reaction (1) can be presented as ΔG _{T, S} = ΔG _T + ΔG _S, where ΔG _T < 0 is the contribution from the Gibbs energy of the thermochemical reaction of oxidation of Ni and Cr atoms and ΔG _S > 0 is the contribution from the surface Gibbs energy of formation of the alloy associated with the replenishment of the surface layer of the alloy during its oxidation. Calculations of ΔG _S are based on the published data on the surface energy of the pure metal ΔG _S ^o and results of authors’ theoretical studies. It was found that the dependence of \({{a_{NiO}^3 } \mathord{\left/ {\vphantom {{a_{NiO}^3 } {a_{Cr_2 O_3 } }}} \right. \kern-\nulldelimiterspace} {a_{Cr_2 O_3 } }}\) on the content of Cr in the alloy determined from calculated equilibrium characteristic of reaction (1) at 1373 K proved to be in satisfactory agreement with the available experimental data on the composition of the oxide film on Ni-Cr alloys. In addition, the values of the potentials of metal-oxide Ni and Cr electrodes in an aqueous solution at 298 K are calculated, which nearly coincide with the published values of the Flade potential for the passivation of these metals.     

The molar formation enthalpy of nano-SiO<Subscript>2</Subscript> with different surface area

Three samples of silicon dioxide were syhthesized and their surface areas were measured. A thermo-chemical cycle was designed to calculate the molar formation enthalpy. The molar formation enthalpy, Δ_f H _m^Φ, for three amorphous silica with the Langmuir surface area 198.0854, 25.1108 and 11.9821 m² g⁻¹ gave −895.52, −910.86 and −915.67 kJ mol⁻¹, respectively. With the increasing surface area, the values of Δ_f H _m^Φ increased accordingly. The results suggest that the silica with larger surface area is more unstable. The wetting heat was also measured by adding the silica powder into water. With the rehydration of the more SiOH groups on the surface, the larger surface areas of silica lead to the more wetting heat. A smaller particle has the more unstable hydroxyl groups and surface energy.     

Proteins at liquid interfaces: I. Kinetics of adsorption and surface denaturation

The rates of change of film pressure (π) and surface concentration (Γ) of protein during the adsorption of β-casein, bovine serum albumin (BSA), and lysozyme at the air-water interface have been monitored by the Wilhelmy plate and surface radioactivity methods, respectively. The increases in π and Γ for the relatively flexible β-casein molecule occur simultaneously with both parameters attaining their steady-state values at about the same time. In contrast, π and Γ follow different time courses for the globular lysozyme molecule; Γ can reach a steady state value while π is still increasing significantly. The kinetics indicate that initially adsorption is diffusion-controlled but at higher surface coverages there is an energy barrier to adsorption. Under these conditions, the ability of the protein molecules to create space in the existing film and penetrate and rearrange in the surface is rate-determining. Two kinetic regions exist: the relaxation time τ₁ (typically ～2 hr when Γ ～2 mg m^?2) describes the adsorption when both π and Γ are increasing whereas τ₂ (in the range 1–8 hr for all three proteins) relates to the situation when π is increasing at constant Γ because the protein molecules are changing conformation in the surface.     

Adsorption-calorimetric determination of the surface energy of dispersed oxides

A new method is proposed for the determination of the surface free energy σ_S and interfacial free energy σ_SL, based on their linear dependence on the specific heat of wetting of dispersed materials by water. The σ_S and σ_SL values of Silochrome, silica gel, and γ-aluminum oxide were determined first by this method. The obtained results are compared with data obtained from the similarity method and the empirical relationship between σ_S and the surface pressure. It is demonstrated that the methods can be used to determine σ_S for the investigated sorbents. Conclusions about the hydrophilicity-hydrophobicity of their surface were reached on the basis of the results. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 2, pp. 75–80, March–April, 2007.     

Wetting films on a hydrophilic silica surface obtained from aqueous solutions of hydrophobically modified inulin polymeric surfactant

The thickness of wetting films on a hydrophilic silica surface was investigated using a microinterferometric technique. Aqueous solutions of hydrophobically modified inulin (INUTEC^®SP1) at various concentrations, in the presence or absence of NaCl or Na₂SO₄, were studied. The equilibrium film thickness (h _eq) showed a complex dependence on INUTEC^®SP1 concentration. At low electrolyte concentrations, h _eq decreased with an increase in INUTEC^®SP1 concentration, reaching a minimum at 10^?6 mol dm^?3. However, at high electrolyte concentrations, this dependence became less pronounced. At any given INUTEC^®SP1 concentration, the equilibrium film thickness decreased with an increase in electrolyte concentration as a result of the compression of the electrical double layer reaching a minimum value. After that, the film thickness showed a small decrease with further increase in electrolyte concentration. This indicates that the electrostatic component of disjoining pressure can be neglected, and the steric repulsion of the loops and tails of INUTEC^®SP1 determined the film thickness.     

The Hydrophobicity Study of Silica and Glass Surfaces Modified with Polyalkylhydrosiloxanes

A procedure based on the analysis of the shape of a sessile drop was used to measure the contact angles of water in air, _a = 93°–97°, for quartz and glass plates modified with polyalkylhydrosiloxanes. The specific heat of wetting, q = 36 mJ/m², and the surface pressure of adsorbed water film, = 48 mJ/m², were determined from adsorption-calorimetric experiment on macroporous disperse silica modified with polymethylhydrosiloxane GKZh-94M. The contact angle in saturated water vapors, _v = 84°, was calculated from these values. It was shown that the liquid-phase modification of silica and glass with polyalkylhydrosiloxanes leads to distinct hydrophobization of the studied surfaces.     

Study on surface hydrolytic kinetics of poly(vinyl acetate) grafted onto polyurethane film

Alkali catalytic hydrolysis of poly(vinyl acetate) (PVAc) grafting onto polyurethane film surface was a heterogeneous reaction. The hydrolysis was carried on the PVAc particle surface, and the concentration of the alkali in the system was tested by titration method. The kinetics of PVAc surface hydrolytic reaction was studied by simple second-order reaction model. From linear regression analysis of experimental data, we inferred that the activation energy (E _a ) and pre-exponential factor (A) of PVAc surface hydrolytic reaction were 70.7 ± 0.2 kJ mol^?1 and (5.7 ± 0.5) × 10¹² kg mol^?1 s^?1, respectively. The results of transmission electron microscopy stated that the apparent hydrolytic degree was 2.1% when the surface of PVAc particle hydrolyzed absolutely.     

Thermodynamics of metal cyanide coordination : Part IX. Log K, ΔH, and ΔS values for the Ni-, Zn-, Cd-, and Hg- CN systems at 10, 25, and 40 °C

Log K, ΔH⁰, and ΔS⁰ values valid at zero ionic strength are reported or summarized from previous studies for cyanide ion interaction with bivalent nickel, zinc, cadmium, and mercury at 10, 25, and 40 °C. From the values of ΔH⁰ as a function of temperature, average ΔC_p⁰ values are calculated.     

Author index

Electromotive-force measurements on cells without liquid junction have been used to determine the pK_a values of 7 mono-, 6 di-, and 2 tricarboxylic acids in formamide at 9 temperatures from 5 to 45°C. From the pK_a values, the thermodynamic quantities ΔG⁰, ΔH⁰, and ΔS⁰ for the acids have been calculated in formamide at 25°C.     

Effect of proton irradiation on structure and optical property of PTFE film

Effects of protons on chemical structure and optical properties of polytetrafluoroethylene (PTFE) film were investigated in the energy range of 60 to 170 keV to simulate the effects of space proton irradiation environment. The results show that for PTFE film irradiated with protons, the change in C_1s spectrum, along with those in F_1s and the FT‐IR spectrum after irradiation, demonstrates that two processes take place simultaneously. One is substitution in which carbon to fluorine bonds can be broken by the protons and some positions of fluorine are occupied by active protons; the other is the carbonification, which results in the change of surface color and an increase of carbon percentage on the irradiated surface. For the PTFE film irradiated with 150 keV protons, the spectral absorbance ΔA_λ in the wavelengths longer than 300 nm increase unmonotonously with proton fluence, and an abnormally recovery decrease of the ΔA_λ with the increase of fluence in the range of 5×10¹³ cm^?2 to 10¹⁵ cm^?2 is observed. The change of the ΔA_λ could be related to the competition of the carbonification and the substituting effect. The carbonification increases the ΔA_λ, while the substituting increases the amorphousness amount, leading to an increase in the transparency of the film. In addition, the creation of radicals can also contribute to the increase in absorbance. Copyright © 2003 John Wiley & Sons, Ltd.     

Angular dependence of 1H-NMR and 2H-NMR spectra of water absorbed in cellulose film

¹H-NMR and ²H-NMR spectra of water (H₂O and D₂O) absorbed in Visking cellulose tubing have been observed as a function of the angle Θ between the film surface and the magnetic field. ¹H-NMR spectra show broad lines, and the chemical shift and the linewidth depend on Θ. From the angular dependence of the chemical shift, the anisotropic volume diamagnetic susceptibilities of the film are determined, i.e., χ_∥ in the direction longitudinal to the tubing (stretched direction) is 0.43 ppm, and χ_⊥ in the transverse direction is 0.57 ppm. The different values of χ_∥ and χ_⊥ afford an evidence of the anisotropy of the film. ²H-NMR spectra of D₂O absorbed in the film show quadrupole splitting which also depends on Θ. The angular dependences of the linewidth (¹H-NMR) and the quadrupole splitting (²H-NMR) indicate that the H? H axes of the water molecules have a tendency to orient in the direction longitudinal to the film surface.     

Preparation of an A-type zeolite film on the surface of an alumina ceramic filter

An A-type zeolite film was prepared on the outer surface of an alumina ceramic filter by repeated hydrothermal syntheses using the same sample (referred to as repeated batch synthesis). The thickness of the film was found to increase to 35 μm by precipitating the crushed zeolite crystal on the ceramic filter and to 50 μm by precipitating the crushed alumina before repeated batch synthesis. The structure and atomic composition of the zeolite film obtained were found to the same as those of the corresponding original zeolite using several spectrometric methods: X-ray diffraction (XRD), ²⁹Si magic-angle spinning nuclear magnetic resonance (MAS NMR) and electron-probe microanalysis (EPMA). The morphology and thickness of the zeolite film were dependent on the reaction time and temperature, and especially on the types of silica and alumina sources. The preferred silica and alumina sources were Na₂SiO₃ and Al(OH)₃, respectively; these are different from the usual sources for the synthesis of powdery A-type zeolites.     

The effect of calcination temperature on the texture of silica gel waste

In this work, the effect of temperature on the texture of silica gel waste is presented and water vapour adsorption in a different humidity is highlighted. It was found that silica gel waste is a mesoporous material with the parallel plates pores. Its specific surface area is equal to 4.61 m² g^?1, and the calculated total pore volume is equal to 9.01 × 10^?3 cm³ g^?1. The texture of silica gel waste changed during calcination in a 188–550 °C temperature interval: S_BET and ΣV_P increased to 11.32 m² g^?1 and 30.06 × 10^?3 cm³ g^?1, respectively. It was determined that the water vapour pressure influenced the mineralogical composition and the quantity of adsorbed water in the samples. The obtained results were confirmed by the differential scanning microcalorimetry, X-ray diffraction, BET and water vapour adsorption analysis data.

     

苯基化硅胶的物理结构和表面性质的研究

本文利用苯基三氯硅烷和硅胶表面羟基反应制备了苯基化硅胶。测定了苯基化硅胶的物理结构、水蒸气吸附等温线、润湿热、差热分析(DTA)和红外光谱(IR)。结果表明,所有苯基化硅胶的真密度(dT)、比表面(S)和比孔体积(V)均减少, 而表观密度(dA)增加, 但苯基化对不同硅胶的平均孔半径(r)有不同的影响; 苯基化硅胶对水蒸气吸附, 对水、苯和环己烷的润湿热均显著减少; 苯基化硅胶的热稳定性大于甲基化硅胶, 甲基化硅胶的表面是高度憎水的, 但苯基化硅胶的憎水性则很弱。     

Surface activity and thermodynamic properties of water‐soluble polyester surfactants based on 1,3‐dicarboxymethoxybenzene used for enhanced oil recovery

The surface activity and thermodynamic properties for eight low molecular weight nonionic co‐polyester (PE) surfactants have been investigated. Surface and interfacial tensions (IFT) of surfactants in aqueous solutions were measured using the spinning drop technique. From these measurements, the critical micelle concentration (CMC), the surface pressure at CMC (Y_CMC), the maximum surface concentration (Γ_max), the minimum area/molecule at the aqueous solution/air interface (A_min), the effectiveness of surface tension reduction (Π_CMC), the alkane carbon number (n_min) and the IFT at n_min (Y_min) were determined. The thermodynamic parameters of micellization (ΔG_mic, ΔH_mic and ΔS_mic) and of adsorption (ΔG_ad, ΔH_ad and ΔS_ad) for these polymeric surfactants were also calculated. Structural effects on micellization and adsorption are discussed in terms of these parameters. The results show that the ΔG_ad values were more negative than ΔG_mic values for these compounds, so that they favored adsorption before the micellization process. They exhibited IFT in the order of 10⁻³ to 10⁻⁴ mN/m against the thin alkane carbon number range 6–9. This range seemed to be prefered for enhanced oil recovery. Copyright © 2000 John Wiley & Sons, Ltd.     

An analysis on changes in structure,tensile properties of polytetrafluoroethylene film induced by protons

Effect of 100 keV proton radiation on the structure and tensile properties of PTFE film was investigated. The change in structure before and after proton radiation was mainly evaluated by means of differential scanning calorimetry. The experimental results show that under radiation of 100 keV protons for the fluence less than 7×10¹⁵ p/cm², the DSC characteristics including the phase enthalpy of transformations at room temperature ΔH_rt1 and ΔH_rt2, the melting enthalpy ΔH_m1 and ΔH_m2, the crystallization exothermal enthalpy ΔH_c, and Tg II were decreased, while the melting temperature was increased a little with the fluence increase. The change in crystallization enthalpy ΔH_c indicated the increase of molecular weight of the PTFE film, but for 150 keV when the fluence exceeded the fluence of 10¹⁶/cm², the molecular weight decreased gradually. With increasing proton fluence, the thermal gravity loss was decreased, while the initial decomposition temperature increased, demonstrating that crosslinking of molecular chains occurred. With the increase of the proton fluence, for proton with energy less than 150 keV, the tensile fracture strength increased at first, but when the fluence exceeded 10¹⁶/cm², the tensile fracture strength showed a decreasing trend. While for the proton of 170 keV, the tensile fracture strength σ_f increased abruptly at the fluence of 2×10¹³/cm², with the fluence increasing further, the tensile fracture strength σ_f decreased gradually. The change of tensile properties could be related with the competition of branching crosslinking and the scission degradation.     

Dynamic elasticity of films formed by poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) microparticles on a water surface

Surface dilatational dynamic elasticity ε of films formed by cross-linked poly(N-isopropylacrylamide) microparticles on a water/air interface has been determined as a function of polymer surface concentration Γ. The experimental dependences exhibit two maxima of ε at surface pressures π of nearly 6 and 35 mN/m. In the region of the second maximum, the pattern of the dependence is governed by a method used to vary Γ. At π > 25 mN/m, film compression leads to the formation of a metastable monolayer, while the gradual addition of a microparticle dispersion results in the establishment of equilibrium between the monolayer and surface aggregates. In the region of π values corresponding to the second maximum of ε, slow relaxation processes with a characteristic time substantially longer than 10 s occur in the system. At π > 35 mN/m, the film collapses due to the displacement of microgel particles from the water surface.     

Thermodynamic studies of hydrogen iodide in dioxane-water mixtures from electromotive force measurements

The standard potentials of the silver-silver iodide electrode were measured in 10,20,30 and 40% (w/w) dioxane-water mixtures at 15,25,35 and 45°C. These values have been used to determine the thermodynamic quantities ΔG_t°, ΔS_t°, ΔH_t° for the transfer of H⁺I^? from water to various dioxane-water mixtures. The ionic ΔG_t° values for H⁺, Cl^?, Br^? and I^? are determined using Feakins method. The chemical and electrical contributions of ΔG_t° are also calculated using the method proposed by Roy and co-workers. The significance of these thermodynamic functions is discussed in relation to the acid—base character of the solvents.     

Kinetic investigation of some steroids by thermogravimetry

The kinetic values of thermal degradation of some steroids were calculated by using TG and DTG curves and the Freeman-Carroll and the Jeres methods. Then andE _a values calculated by the Jeres method are more reasonable. The kinetic thermal stabilities of the simple functional groups of the steroids were compared by using theE _a values of Jeres, and the following sequences were found: 17β-OH>17-octy 1>17-Ac-CHO>17-keto; 3β-OH> 3-keto>3a-OH; and 5a-H>5β-H>Δ⁵⁽⁶⁾>Δ⁴. The k,Z, ΔH^*, ΔS^* and ΔG^* values were calculated at the maximum decomposition rate temperatures by using the Jeres values. The ΔS^* values are negative and suggest a high ordering of the transition state. The ΔH^* and ΔG^* values are positive, as expected.     

Comparison of classical mechanics and the coupled states approximation for Li+-CO scattering on an ab initio calculated CI potential energy surface

The dynamics of rotational excitation on an ab initio calculated CI rigid rotor potential energy surface for Li⁺-CO are investigated using classical mechanics and the quantum mechanical coupled-states (CS) approximation. Transition probabilities out of the j = 0 initial level are calculated for various impact parameters between b = 0 and 40a_o for 1 eV collisions. The classical results agree well with the average of Δj-even and Δj-odd quantum transition probabilities except for a few lower impact parameters where CS seems to underestimate the large Δ transitions. No propensity rule is observed for the preference of the Δj-even versus Δj-odd transitions as might have been expected.