Ligand exchange chromatography for analysis and preparative separation of tritium-labelled amino acids

Racemic tritium-labelled amino acids were separated into optical isomers by chromatography on a chiral polyacrylamide sorbent filled with copper ions. The polyacrylamide sorbent is synthesized by Mannich's reaction through the action of formaldehyde and L-phenylalanine upon polyacrylamide Biogel P-4 in an alkali phosphate buffer. Tritiumlabelled amino acids are eluted by a weak alkali solution of ammonium carbonate. Data are presented on the ligand exchange chromatography of amino acids depending on the degree to which the sorbent is filled with copper ions and on the eluent concentration. Conditions are suggested for the quantitative separation of amino acid racemates. Amino acids are isolated from the eluent on short columns filled with sulfonated cation exchanger in the H⁺ form. HPLC on modified silica gel sorbents is also used for the analysis of tritium-labelled optically active amino acids. Amino acids are eluted by a weakly acidic water-methanol solution containing ammonium acetate. UV and scintillation flow type detectors are used.     

Potential of Flame Ionization Detection Coupled On‐Line with Microcolumn Liquid Chromatography Using Aqueous Eluents and an Eluent‐Jet Interface

The potential of the on‐line coupling of microcolumn liquid chromatography (μLC) using aqueous eluents with a flame ionization detector (FID) was evaluated. An eluent‐jet interface was modified to allow the efficient introduction of the eluent into the FID. The potential of the method is demonstrated by the μLC–FID determination of lower alcohols and bis(2‐hydroxyethylthio)alkanes on porous and non‐porous stationary phases, respectively. Flow injection analysis (FIA)–FID experiments with highly polar, thermolabile, semi‐volatile and non‐volatile compounds like amino acids, organic acids, alkylphosphonic acids, and carbohydrates showed the developed configuration to be a promising approach for the detection of a wide range of analytes. Compared with a nebulization interface, the eluent‐jet interface showed 4–10 times higher peaks for citric acid. Detection limits by FIA for all compounds were in the range of 0.2–5 ng injected. With ribose as test compound, plots of peak height vs. amount injected showed good linearity (r² > 0.999) in the range of 75–12,000 μg/mL. The repeatability showed relative standard deviations of less than 5%.     

Flame ionization detection after splitting the water effluent in subcritical water chromatography

The coupling of subcritical water separation with flame ionization detection (FID) in the split mode has been investigated in this study. In order to keep the FID system stable during subcritical water separation, a Tee union was connected between the separation column and the FID system to split the water flow. The ratio of the water flow to the FID system over the flow-rate to a waste bottle varied depending on the dimension of capillary tubings and the total water flow-rate used. Separations of several carbohydrates, carboxylic acids, and amino acids were performed on commercially available columns using a laboratory-made subcritical water chromatography-FID system. The FID system was very stable in this split mode even at total flow-rate as high as 1.24 ml/min. The linear dynamic range was up to three orders of magnitude and the limit of detection (LOD) ranged from 38 to 111 ng (306-925 ng/microl injected) with split ratios of approximately 1:10 to approximately 1:17 (FID/waste bottle) for several analytes studied. However, the LOD can be significantly lowered by adjusting the dimensions of the restrictors to allow a higher percentage of the total flow to the FID system.     

Dynamic control of split flow in packed column supercritical fluid chromatography using dual resistively heated restrictors

Remote control of the vent/detector split flow ratio in packed column supercritical fluid chromatography (pSFC) with flame ionization detector (FID) is demonstrated using a dual heated restrictor method. Restrictors stemming from a Tee at the separation column outlet were, respectively, fixed into an FID and a vent port, and their individual temperatures were controlled using resistively heated wires. Subsequently, both system pressure and split flow could be manipulated. For example, for applied restrictor temperatures examined up to 600°C, corresponding vent/FID split flow ratios between 2 and 7 were observed depending on the port heated. As well, column pressures around 16–23 MPa were also achievable over the same range. Conversely, isobaric altering of the split flow ratio was possible when opposing positive and negative temperature gradients were applied at the two restrictors. Under these conditions, the system pressure varied less than 1% RSD over a 10 min period. As an application, the method was used to establish stable detector operation in the analysis of n‐alkanes under pSFC‐FID conditions that initiated flame instability. Results indicate that this technique could be a relatively simple and inexpensive means of controlling system pressure and detector split flow ratios in pSFC‐FID.     

Simple Free Amino Acid Separation by Reversed-Phase Ion-Pair Liquid Chromatography Using Column Switching Technique

Abstract

Reversed-phase ion-pair liquid chromatography with copper (II) ions (RP-IPC-Cu) was applied to develop a high speed separation of free amino acids. Dynamic gradient elution in RP-IPC-Cu could not achieve this purpose due to base line shift, therefore a column switching technique was used with a combination of different alkyl-bonded silica gel columns under isocratic elution. The flexibility of eluent components makes it easy to realize a rapid separation of a mixture of targeted amino acids.     

Optimization of the coupling of high-temperature liquid chromatography and flame ionization detection application to the separations of alcohols

The feasibility of coupling high-temperature liquid chromatography (HTLC) to flame ionization detection (FID) has been studied. FID parameter values (hydrogen flow-rate, air flow-rate and FID temperature), typically set in gas chromatography are rarely suitable for liquid chromatography. Best values depend obviously on the water flow rate which is defined depending on both column temperature and column internal diameter. The FID parameters were optimized according to the water flow-rate by means of an experimental design. The potential of the method is shown with some alcohol separations and the value of increasing column temperature while reducing the column diameter is highlighted.     

Analysis of oligosaccharides using aminobonded silica gel and a ternary eluent with evaporative light scattering detection

Using two commercial, amino bonded, silica gel columns, binary eluents (methanol/water, acetonitrile/methanol) and ternary eluents (acetonitrile/methanol/water) are evaluated for their ability to separate oligosaccharides in comparison with classical acetonitrile/water eluents. Chromatographic data on glucose, maltose, raffinose, stachyose and maltodextrin are reported. Mobile phases consisting of acetonitrile/water or acetonitrile/methanol/water produce the best separations. Phase hydrolysis is evaluated using an evaporative light scattering detector. The reduction of the water content in the eluent stabilizes the aminocolumns and the life time of the amino columns should be improved with the ternary eluent. Moreover, a better detection limit can be obtained. Capabilties to run gradient elution without baseline drift are clearly demonstrated.     

二甲醚气相色谱相对重量校正因子的测定

用冰冷却水吸收二甲醚配制样品,将ＴＣＤ和ＦＩＤ串联使用,测定出二甲醚在ＴＣＤ和ＦＩＤ上相对于甲醇的重量校正因子分别为０．８６和０．５５,并通过用甲醇催化脱水生成的二甲醚和水的化学计量关系,在线间接测定二甲醚在ＴＣＤ上相对于甲醇的重量校正因子,从而使上述测定结果得到佐证。     

Polymeric columns for liquid chromatography

Polymeric columns are becoming used more frequently in modern liquid chromatography applications as improvements in polymeric packing materials are realized and as more applications are developed for these materials. Modern polymers have overcome earlier problems associated with their use; higher rigidity now allows them to be used at normal eluent flow rates resulting in faster analyses, and improved synthesis techniques have resulted in efficiencies comparable to the best silica materials, sometimes exceeding 100,000 plates/m. In addition, polymers offer distinct advantages over silica packing for particular applications. Because silica packings are readily degraded by aqueous eluents, they are not always suitable for separations involving ionic species. Polymeric columns are particularly useful in determinations of amino acids, peptides, proteins, organic acids, carbohydrates, and inorganic cations and anions. Polymers are also characterized by exceptional lot-to-lot reproducibility. Reproducibility is often problematic with silica packings, particularly the bonded phases.     

Fitting adsorption isotherms to the distribution data determined using packed micro-columns for high-performance liquid chromatography

Knowing the adsorption isotherms of the components of a mixture on the chromatographic system used to separate them is necessary for a better understanding of the separation process and for the optimization of the production rate and costs in preparative high-performance liquid chromatography (HPLC). Currently, adsorption isotherms are usually measured by frontal analysis, using conventional analytical columns. Unfortunately, this approach requires relatively large quantities of pure compounds, and hence is expensive, especially in the case of pure enantiomers. In this work, we investigated the possible use of packed micro-bore and capillary HPLC columns for the determination of adsorption isotherms of benzophenone, o-cresol and phenol in reversed-phase systems and of the enantiomers of mandelic acid on a Teicoplanin chiral stationary phase. We found a reasonable agreement between the isotherm coefficients of the model compounds determined on micro-columns and on conventional analytical columns packed with the same material. Both frontal analysis and perturbation techniques could be used for this determination. The consumption of pure compounds needed to determine the isotherms decreases proportionally to the second power of the decrease in the column inner diameter, i.e. 10 times for a micro-bore column (1 mm I.D.) and 100 times for capillary columns (0.32 mm I.D.) with respect to 3.3 mm I.D. conventional columns.     

烟叶和烟草料液中氨基酸的直接检测及碳水化合物的去除

建立了高效阴离子交换色谱-积分脉冲安培法(HPAEC-IPAD)直接检测烟叶和烟草料液中氨基酸的方法。利用离线除糖的方法,去除烟叶和烟草料液中大量干扰糖类,包括葡萄糖、果糖和蔗糖及麦芽低聚糖等。采用AminoPac PA10阴离子交换柱,以NaOH和NaAc的强碱性溶液为淋洗液,采用梯度洗脱,流速为0.25 mL/min;积分脉冲安培法对氨基酸进行检测,回收率可达76%~105%。此方法可以有效的解决烟叶、烟草料液等含糖量高的样品中糖类化合物的干扰,对氨基酸实现灵敏、准确的定量分析。     

Development of a contactless conductivity detector cell for 1.6 mm O.D. (1/16th inch) HPLC tubing and micro-bore columns with on-column detection

A capacitively coupled contactless conductivity detector cell was designed and constructed suitable for standard HPLC 1.6 mm o.d. (1/16') tubing and columns. Bode plots were acquired in order to determine the optimum input frequency for the new detector cell, with three feedback resistors of increasing resistance (1 MOmega, 3.3 MOmega and 4.7 MOmega) alternately fitted to maximize sensitivity. To evaluate the new detector geometry, a 190 mm x 0.381 mm i.d. (1.59 mm o.d.) column packed with Dionex OmniPac 8.5 microm PAX-100 anion exchange resin was used, with an eluent of 0.5 mM sodium benzoate containing 2% methanol, pumped at 20 microL min(-1), with detection taking place 'on-column'. Standard analytical performance criteria were used to compare the test detector with a commercially available TraceDec C(4)D capillary (360 microm o.d.) detector, with the new detector cell matching the performance of the commercial instrument in terms of linearity, sensitivity and reproducibility. In 'on-column' detection mode, the detector cell could be moved during (or between) chromatographic runs along the length of the packed column bed, to shorten the effective length of the column and thus reduce the retention time of strongly retained sample components, whilst maintaining the resolution of weakly retained components. In addition, the detector could also be applied to the evaluation of the stationary phase packing homogeneity by physically scanning the entire length of the micro-bore column with the moveable detector cell.     

Gravity-flow open tubular cation chromatography

We describe ion chromatography (IC) on open tubular cation exchange columns with a controllable capacity multilayered stationary phase architecture. The columns of relatively large bore (75 microm id) are fabricated by coating fused-silica capillaries with multiple layers of poly(butadiene-maleic acid) (PBMA) copolymer and crosslinking the deposited layers by thermally initiated radical polymerisation. Column capacity increases in a predictable manner with increase in the number of successively coated layers. Gravity flow with a modest head (< 2 m) can provide the desired separations within a reasonable period. We provide a minimalist configuration where no suppression is used, the sample is injected hydrodynamically as in CE, and detection is accomplished by an inexpensive homebuilt contactless conductivity detector or a capacitance to voltage digital converter. A 1 m long 75 microm bore column coated with two layers of PBMA allows gravity-flow open tubular IC to separate four alkali cations in < 10 min with a 1 mM tartaric acid (TA) eluent. Simultaneous separation of alkali and alkaline earth metal cations can be accomplished in less than 25 min using 1.75 mM pyridinedicarboxylic acid as an eluent. Contactless conductometric detection (C(4)D) allows LODs down to 150 nmol/L, corresponding to 30 fmol injections. Analysis of real water samples is demonstrated.     

Metal selective flame ionization detection after supercritical fluid chromatography

This work describes the construction and operation of a flame ionization detector for the selective detection of metal-containing compounds after capillary supercritical fluid chromatography. Using optimal conditions for achieving metal sensitive flame ionization responses which have been established for the detector after capillary gas chromatography, initial evaluation of the detector after SFC proved promising. Like the carbon sensitive FID, it appears that the metal sensitive FID is compatible with SFC when pure carbon dioxide is used as the mobile phase. Response characteristics were found to be similar to those observed when the detector is used in gas chromatography.     

Rapid, low pressure, and simultaneous ion chromatography of common inorganic anions and cations on short permanently coated monolithic columns

Short permanently coated reversed-phase silica based monolithic columns have been investigated for the rapid separation of inorganic anions and cations. One 2.5 x 0.46 cm column was permanently coated with didodecyldimethylammonium (DDAB), for anion analysis; and a second 5.0 x 0.46 cm column was coated with dioctylsulphosuccinnate (DOSS), for cation analysis. The use of a single combined eluent of 2.5 mM phthalate/1.5 mM ethylenediamine, at flow rates of between 4.0 and 8.0 mL/min, resulted in the rapid separation of 8 anions (in under 100 s) and 5 cations (in under 100 s) on the above columns when used individually, with detection limits for common anions ranging from approximately 0.25 to 5 mg/L, and between 2.5 and 50 mg/L for alkaline earth metals, by direct and indirect conductivity detection, respectively. However, with both columns subsequently connected in parallel, with the eluent delivered using a flow splitter from a single isocratic pump, the simultaneous analysis of anions and cations was also possible, based on a single conductivity detector. The potential of this system for the rapid, complete screening of water samples for multiple common anions and cations is shown.     

High performance liquid chromatography of raw sugars and polyols using bonded silica gels

Summary Bonded silica columns have been evaluated for their ability to separate carbohydrates and polyols. Mobile phases consisting of dichloromethane/methanol produced the best separations in comparison with the acetonitrile/water mixtures commonly used with amino columns. Of all the bonded phases tested, LiChrospher Diol silica provided the best separations, and selectivities were not very different from those obtained on the most popular system using an amino bonded phase and acetonitrile/water as eluent. In addition, diol columns with a dichloromethane/methanol eluent offer excellent stability with no Schiffs base formation of reducing sugars. Using an evaporative light scattering detector, low limit detection is obtainable (20 ng of glucose from a column) and gradient elution is quite feasible.     

离子色谱法同时测定饮用水中强极性农药草甘膦、草铵膦、乙烯利和调节膦

建立了一种梯度洗脱-电导抑制-离子色谱同时测定4种强极性农药的方法.通过对淋洗液及浓度、色谱柱、柱温、进样量等条件的优化,得到最佳检测条件:色谱柱为IonPac AS11-HC分析柱及IonPac AG11-HC保护柱,柱温33℃,进样量50μL,RFIC系统的淋洗液自动发生器在线产生的KOH作为淋洗液,梯度洗脱,淋洗...     

Last ten years (2008–2018) of chiral ligand‐exchange chromatography in HPLC: An updated review

Chiral ligand‐exchange chromatography is one of the elective strategies for the direct enantioresolution of small chelating compounds: amino acids, diamines, amino alcohols, diols, small peptides, etc. Unlike other methods, the interaction between chiral selector and analyte enantiomers is mediated by a cation, thus producing diastereomeric ternary complexes. Two main approaches are conventionally applied in chiral ligand‐exchange chromatography. The first relies upon chiral stationary phases where the chiral selector is either covalently immobilized or physically adsorbed onto suitable packing materials (coated phases). In the second approach, chiral molecules are added to the eluent, thus generating chiral eluent systems. Among the advantages of chiral ligand‐exchange chromatography, the generation of UV/vis‐active metal complexes, and the use of commercially available or easy‐to‐synthesize chiral selectors, in combination to rather inexpensive achiral columns for coated phases and chiral eluents, are noteworthy. Besides amino acids and amino alcohols, other species have proven suitable for chiral ligand‐exchange chromatography applications. Recently, the use of either chiral ionic liquids or micellar liquid chromatography systems as well as the successful off‐column formation of diastereomeric complexes have expanded the selectivity profiles and application fields. All of these issues are touched in the review, shedding light to the contributions appeared in the last decade.     

烟用香精的气相色谱法质量控制研究

采用配有氢焰检测器或催燃检测器的气相色谱仪,对烟用香精进行了快速分析。方法操作简便,结果可靠,可作为烟用香精原料、产品质量监控的有效手段。     

三通道气相色谱法测定炼厂气组成

炼厂气是炼油工艺产生的各种气体的混合物,采用四阀六柱将炼厂气分离分解为3部分,以双TCD+FID检测器3通道气相色谱法快速分析炼厂气.FID通道用于分析烃类,一个TCD通道分析永久性气体和硫化物,另一个TCD通道分析氢气,采用面积归一化法定量计算分析结果.用该法测定了3种标准气体,测定值与标准值基本一致,测定结果的相对标准偏差小于8％.该法适用于测定包括液化气、烟气、裂解气等组分相近的样品组成.