等离子体激励翼型分离流动控制数值模拟

文章利用CFD软件FLUENT中的自定义函数接口, 将等离子体对中性气体的激励作用模型化为体积力引入Navier-Stokes方程, 研究了等离子体气动激励诱导的平板射流, 以及介质阻挡放电(dielectric barrier discharge, DBD)等离子体激励对NACA0015翼型大迎角分离流的控制作用.计算分析表明, 多对电极等离子体激励器可以有效控制NACA0015翼型大迎角分离流动.      

同轴枪放电等离子体电流片的运动特性研究

同轴枪放电可以产生高速度、高密度的等离子体射流,在天体物理、核物理等研究领域具有广泛的应用.基于同轴枪放电等离子体运动的"雪犁模型"分析,本实验通过对等离子体光电信号和磁信号的测量及放电照片的拍摄,研究了不同放电电流和气压对同轴枪放电等离子体电流片的运动特性、电流通道分布的影响.实验结果发现:一次放电过程中,气压为10 Pa、放电电流为35.7—69.8 kA时,随着放电电流的增加,等离子体喷射速度增加,输运距离与离子携带的轴向动能成正比,大电流条件下,等离子体喷出枪口时易于在枪底端形成新的电流通道;气压为5—40 Pa、放电电流为49.8 kA时,随着气压的增加,等离子体喷射速度减小,输运距离缩短,高气压下,等离子体喷出枪口时在枪底端未产生新的放电通道,这与放电过程中遗留在枪底端的带电粒子和电流片渗漏残留在枪内的中性粒子共同形成的阻抗通道有关;电流反向时,二次放电击穿位置发生在电极头部,放电过程中存在多次放电现象.     

HT-7托卡马克等离子体slide-away放电研究

在HT-7托卡马克上,只在等离子体放电击穿阶段充气,击穿后关闭充气阀门,让装置内真空室器壁的出气维持放电的进行,通过密度衰减实现了slide-away放电.实验分析了不同等离子体电流平台下的slide-away放电模式的密度阈值,以及相同充气量的条件下放电等离子体电流对实现slide-away放电的影响.研究了slide-away放电模式下密度提升对等离子体放电状态的影响.结果发现,slide-away放电模式下的密度提升使得H_a线辐射强度增强,等离子体中超热电子的约束性能变差,等离子体芯部的超热电子减少,高能逃逸电子厚靶轫致辐射增加. 关键词： slide-away放电 托卡马克 等离子体 逃逸电子     

Discharge and flow characterizations of the double-side sliding discharge plasma actuator

We investigate the discharge and flow characterizations of a double-side siding discharge plasma actuator driven by different polarities of direct current(DC) voltage. The discharge tests show that sliding discharge and extended discharge are filamentary discharge. The irregular current pulse of sliding discharge fluctuates obviously in the first half cycle,ultimately expands the discharge channel. The instantaneous power and average power consumptions of sliding discharge are larger than those of the extended discharge and dielectric barrier discharge(DBD). The flow characteristics measured by a high-frequency particle-image-velocimetry system together with high-speed schlieren technology show that the opposite jet at the bias DC electrode is induced by sliding discharge, which causes a bulge structure in the discharge channel.The bias DC electrode can deflect the direction of the induced jet, then modifying the properties of the boundary layer.Extended discharge can accelerate the velocity of the starting vortex, improving the horizontal velocity profile by 203%.The momentum growth caused by extended discharge has the largest peak value and the fastest growth rate, compared with sliding discharge and DBD. However, the momentum growth of sliding discharge lasts longer in the whole pulsed cycle,indicating that sliding discharge can also inject more momentum.     

两电极等离子体合成射流激励器工作特性研究

采用放电测量和高速阴影技术对两电极等离子体合成射流激励器工作特性进行了系统实验研究.实验表明:激励器工作击穿电压和放电峰值电流随激励器所处环境压强的降低和放电频率的增大而减小,激励器腔体内的放电过程为火花电弧放电.典型的等离子体合成射流流场包含有一道前驱激波和一股呈蘑菇状的高速射流.在整个射流发展过程中,前驱激波以当地声速恒速传播,不随激励器条件的改变而变化,波的强度则随着激励器出口直径的减小、腔体体积的增大、环境压强的降低和放电频率的升高而减小.激励器腔体体积和放电频率的增加会降低腔内气体的加热效果,并减小射流速度.激励器出口直径和环境压强对射流速度的影响按规律变化且存在最佳值.本文实各验条件下激励器都产生了明显的前驱激波和高速射流,具有实现高速流场主动流动控制的应用潜能.     

The effects of normal current density and the plasma spatial structuring in argon DBDs

This paper presents the results of theoretical studies of high-pressure dielectric barrier discharges (DBD) in argon. Two different DBDs at the megahertz and the kilohertz power frequency range were simulated. The effect of normal current density was obtained in the numerical model for both types of the discharge. The discharge of megahertz range was uniform over the radius. The increase in the discharge current is accompanied by increase in the discharge area. The discharge of kilohertz range is not uniform over the radius. The concentric ring formation was observed during calculations. The increase in the discharge current occurs due to increase in the number of rings and as a result in the discharge area. The developed 2D model is able to describe only the first stage of the filament formation – the formation of concentric plasma rings. The filament formation starts at the edge of the current channel and spreads to its centre. Both the effect of normal current density and the filaments formation are caused by the nonstationarity at the current channel boundary.     

Parameters of an erosion carbon plasma in the channel of a railgun

The working current dependences of the thermodynamic and electrophysical parameters of a free plasma piston moving with a near-maximal velocity in the channel of an electromagnetic rail launcher with graphite electrodes are obtained. The composition and weight of the plasma depend on the degree of electrode erosion due to discharge current passage (i = 40–80 kA). It is shown that the mean temperature of the plasma piston only slightly depends on the plasma mean pressure and plasma piston weight and increases with current by a near-power law. The measured values of the maximal velocity of the plasma piston front are compared with the calculated value of the sound velocity inside the piston. With the working current and cross-sectional area of the channel fixed, the initial gas density in the channel is found to influence the ratio of the piston maximal velocity to the sound velocity in the plasma. If the initial gas density is low (lower than some critical value), the maximal velocity of the plasma piston front exceeds the sound velocity in the plasma.     

��������������������������������ܵķ����о�

基于介质阻挡放电等离子体体积力气动激励机理,数值研究了两种等离子体流动控制方案对螺旋桨桨径根部处于负攻角工况下叶素气动性能的改善效果.结果显示,激励器布置在下翼面时等离子体体积力大于其布置在叶素前后缘时的情况;激励器布置在下翼面时,可抑制流动分离,使得螺旋桨桨根部位叶素产生更大的负拉力,但会减小螺旋桨的扭矩;激励器布置在前后缘时,会使螺旋桨根部叶素拉力增大,提高螺旋桨总拉力,但不能抑制流动分离,所以会增大螺旋桨的扭矩.     

液体电极上辉光放电丝的运动特性研究

大气压液体电极放电在生物医疗、化学降解、环境保护等众多方面具有广泛的应用前景,引起了研究者的关注.本文利用直流电压激励棒-水电极装置,在6 mm气隙间产生了大气压辉光放电.研究发现,随着电流的增大,放电由锥状转变成柱状,且此过程中水面上放电环的直径先增大后减小.利用高速照相机对放电进行研究,发现锥状放电是由单个放电丝旋转形成的.通过测量放电的伏安特性,表明放电处于正常辉光机理.利用光谱学方法,研究了不同电流下的振动温度、转动温度和谱线强度比I_(391.4)/I_(337.1),发现它们均随电流的增加而增大.根据气体放电理论,分析和解释了放电丝的运动机理,并对水面上放电环直径随电流的变化关系进行了解释.这些结果对于大气压液体电极放电的理论研究和实际应用均具有一定参考价值.     

Active plasma grid for on-demand airflow mixing increase

The present paper concerns the electromechanical characterization of an actuator composed of a ceramic plate perforated by 121 holes housing embedded and printed electrodes between which a high voltage is applied. The electrode arrangement is such that the holes where the gas flows are surrounded by surface discharges. Electrical measurements and iCCD images show that the discharge behaves as a typical surface dielectric barrier discharge with streamer and glow regimes during one period of the AC sine voltage. Particle image velocimetry has been used to measure the jet flow produced by the discharge. The plasma discharge is at the origin of a wall jet with mean velocity of about 2.2 m/s, oriented from the active electrode to the grounded one. The capability of this discharge for promoting mixing by reducing the length of the jet core is demonstrated for flow velocities from 20 up to 60 m/s. In all the tested cases, the actuator can improve the mixing downstream of the perforated plate, when periodic perturbations are imposed at the jet column mode (St_D = 0.3).     

Modeling of plasma behavior in a plasma electrode Pockels cell

We present three interrelated models of plasma behavior in a plasma electrode Pockels cell (PEPC). In a PEPC, plasma discharges are formed on both sides of a thin, large-aperture electro-optic crystal (typically KDP). The plasmas act as optically transparent, highly conductive electrodes, allowing uniform application of a longitudinal field to induce birefringence in the crystal. First, we model the plasma in the thin direction, perpendicular to the crystal, via a one-dimensional fluid model. This yields the electron temperature and the density and velocity profiles in this direction as functions of the neutral pressure, the plasma channel width, and the discharge current density. Next, me model the temporal response of the crystal to the charging process, combining a circuit model with a model of the sheath which forms near the crystal boundary. This model gives the time-dependent voltage drop across the sheath as a function of electron density at the sheath entrance. Finally, we develop a two dimensional MHD model of the planar plasma, in order to calculate the response of the plasma to magnetic fields. We show how the plasma uniformity is affected by the design of the current return, by the longitudinal field from the cathode magnetron, and by fields from other sources. This model also gives the plasma sensitivity to the boundary potential at which the top and bottom of the discharge are held. We validate these models by showing how they explain observations in three large Pockels cells built at Lawrence Livermore National Laboratory     

Effect of pressure on the performance of plasma synthetic jet actuator

The effects of the ambient air pressure level on the performance of plasma synthetic jet actuator have been investigated through electrical and optical diagnostics.Pressures from 1 atm down to 0.1 atm were tested with a 10 Hz excitation.The discharge measurement demonstrates that there is a voltage range to make the actuator work reliably.Higher pressure level needs a higher breakdown voltage,and a higher discharge current and energy deposition are produced.But when the actuator works with the maximum breakdown voltage,the fraction of the initial capacitor energy delivered to the arc is almost invariable.This preliminary study also confirms the effectiveness of the plasma synthetic jet at low pressure.Indeed,the maximum velocities of the precursor shock and the plasma jet induced by the actuator with maximum breakdown voltage are independent of the ambient pressure level;reach about 530 and 460 m/s respectively.The mass flux of the plasma jet increases with ambient pressure increasing,but the strength of the precursor shock presents a local maximum at 0.6 atm.     

Excitation of the Potential Relaxation Instability in a Weakly Magnetized Discharge Plasma by a Voltage Step

An instability is triggered in a weakly magnetized discharge plasma by the application of a positive voltage step to a planar collector immersed into the plasma column with its surface perpendicular to the magnetic field lines. Time developement of the plasma density after the application of the pulse is measured by a Langmuir probe. Radial and axial velocity of the plasma density perturbation are measured. Radial velocity is consistent with the increase of the plasma potential in the current channel. Axial velocity is very high. It is interpreted as phase velocity of radial quasiperiodic motion of the plasma in and out of the current channel. Response time of the collector current to the applied voltage step is measured versus different parameters. Experimental results are in agreement with a qualitative model presented in previous work [1] where the observed instability is modeled as a two dimensional potential relaxation instability (PRI). Minor improvements of the previous model are proposed. A rarefaction pulse that moves towards the collector is found as the initial stage of the instability.     

容性耦合射频氩等离子体放电诊断研究及仿真模拟

针对中等气压、中等功率下射频容性耦合(CCRF)等离子体的放电特性,采用基于流体模型的COMSOL软件仿真,建立一维等离子体放电模型,以Ar为工作气体,研究同一气压时不同射频输入功率下等离子体电子温度和电子密度的分布规律。同时依据仿真模型设计制作相同尺寸的密闭玻璃腔体和平板电极,实验测量了不同射频输入功率时放电等离子体的有效电流电压及发射光谱,进而计算等离子体的电子温度及电子密度;利用玻耳兹曼双线测温法,得到光谱法下等离子体的电子温度及电子密度。结果表明:当气体压强为250 Pa、输入功率为100~450 W时,等离子体电压电流呈线性关系,电子密度随功率的增大而增大,而电子温度并未随功率的变化而有明显变化,其与功率无关。运用仿真模拟验证了实验的准确性,通过比较,三种方法所得的结果相近。通过结合等效回路法、光谱法和数值模拟仿真法初步诊断出中等气压下等离子体的放电参数,提出了结合三种方法作为实验研究的方法,使实验结果更具说服力,证明其方法的可靠性,也为进一步的等离子体特性研究提供依据。     

A steadily rotating plasma disk

A homogeneously rotating plasma disk can be formed in a radially directed Ar-arc discharge at reduced pressure with an externally applied axial magnetic field. The radial pressure distribution is measured, as well as the emitted continuum radiation and the arc voltage. With these experimental values profiles of temperature, radial and azimuthal current density, and flow velocity in the disk are evaluated. Viscosity determines the flow pattern essentially. The effects of magnetic field and rotational motion on the discharge are investigated. The disk exhibits at nonrigid rotation a strong centrifugal force and a minor Coriolis force. A weak double vortex is found to develop in the meridional plane. The electric field in the discharge is altered by the azimuthal plasma flow.     

等离子体激励器的静特性与高速特性仿真研究

A parametric study of high-frequency plasma jet actuator was carried out, using the experiment- tally measured energy distribution law of arc discharge as an ideal heat source. The influence of the exit angle of the actuator on the flow field was explored. The jet flow field characteristics of the spark discharge actuator under supersonic flow (Ma0=2.0) were investigated. The results show that the energy density of heat flux increases and the jet front and forward shock wave moves faster with the decrease of discharge region, and the smaller the exit angle of the jet is, the stronger the momentum injection ability of the actuator along the flow direction is. The rule still applies under high-speed air flow conditions. Compared to the static condition, the momentum injection capability of the jet is stronger and the influence domain is larger under supersonic flow conditions.     

高功率微波在等离子体填充波导中的传播特性

 在考虑有质动力情况下对高功率微波在等离子体填充波导中的传播特性进行了理论分析和数值计算,研究了高功率微波在等离子体中的传播特性和微波场强与等离子体密度分布之间的关系。结果表明高功率微波的有质动力将影响微波色散特性,使微波场强分布偏离Bessel分布,并对等离子体有排开作用,当场强足够大时可将波导中心处等离子体排空形成低密度通道。     

等离子体喷射触发气体开关多通道放电特性

为了能够形成稳定的多通道放电,研制了一种等离子体喷射触发气体开关。在触发电极的内部嵌入多个微型激励腔以形成多通道等离子体喷射,从而在主间隙中诱导多通道放电。研究了触发电路连接方式、触发能量和极性对多通道等离子体喷射的影响,比较了开关在两种工作模式下各间隙放电通道数量随工作系数的变化规律。实验结果表明:采用触发电路II连接方式,触发电极的多通道放电效果更好;高触发能量、负极性和低气压条件有利于形成多通道等离子体喷射;当开关运行在工作模式Ⅱ,且在较高工作系数时,具有更好的多通道放电特性。     

Computation of the tracking force acting on a relativistic electron beam propagating in a conducting waveguide under the ohmic and ion-focused regimes

The force of interaction between a relativistic electron beam deflected by resistive hose instability and the eddy current induced in a tubular plasma channel of finite conductivity is computed. Dependences of the force on channel ohmic conductivity and current rise time in a beam pulse are studied. For a beam propagating through a perfectly conducting waveguide under the ion-focused regime, the interaction of the beam with the ion-channel electrostatic image on the waveguide wall is studied for the case when the beam and the channel are deflected from the waveguide axis as a result of ion hose instability. The dependence of the force on both deflection amplitudes is ascertained for the nonlinear phase of instability. It is demonstrated that the force under study may become comparable to the beam-channel interaction force if the deflections are large.     

放电参数对爆燃模式下同轴枪强流脉冲放电等离子体的影响

同轴枪强流脉冲放电常见有爆燃模式和预填充模式两种放电模式,爆燃模式放电可以得到杂质少、准直性高、输运速度更快的等离子体射流.本实验主要对不同电压及进气量下同轴枪强流脉冲爆燃模式放电的等离子体特性进行了研究.结果表明,在相同放电电压下,进气量少时会有多团等离子体从枪口喷出.随着进气量的增加,同轴枪放电产生的等离子体密度增加,输运速度减小,最终等离子体只有一团从枪口喷出;而在相同进气量下,随着电压的增加,等离子体密度增加,输运速度增大,开始出现有多团等离子体从枪口喷出的现象.产生该现象的原因主要是在放电过程中,当气体持续进入枪底部时,同轴枪底部会产生新的电流通道向前运动,使得在同轴枪出口处观察到了多团等离子体喷出的现象;随着放电电压的增加,在放电过程中回路电流也增加.当电流增加到一定程度时,同轴枪底部就会产生新的电流通道,从而有多个等离子体团从枪口喷出.通过改变充电电容以及对磁探针信号的分析,进一步分析并验证了同轴枪底端多次放电的现象.