Field deformation and loss by curvature in gain guided and index anti-guided fibers

Gain guided and index anti-guided fiber, being a new kind of fiber with a great potential application on large mode area lasing devices, has the inevitable geometric curvature, which induces field deformation and bending losses. In this paper, the method of complex-value extended Fourier-Bessel series is introduced on optical field deformation and bending losses by geometric curvature in the case of this new fiber. Comparing with conventional fibers, gain guided and index anti-guided fiber has better performance on anti-curvature; the quantity of optical intensity centre being shifted from fiber geometric center is less than the case of conventional index guided fibers; and the bending losses decrease dramatically with the increase of curvature radius.     

2×2熔锥型单模光纤耦合器的模型

选择适当的连续函数描述了熔锥型耦合器熔锥形状的渐变特性及其相互位置关系,然后分别应用局部模式理论和变分法分析了横截面沿纵向变化的锥形区域和横截面近似不变的耦合区域内的耦合行为,得出了耦合器中任一横截面处的耦合系数和耦合功率表达式计算表明,熔锥型耦合器的总功率耦合主要发生在耦合区域,在两锥形区域,对于纤芯归一化频率小于1.08的部分,也发生了相当程度的耦合为了使耦合器的理论模型更接近于实际物理情况,锥形区域的耦合作用也是不容忽略的,从而得到了一个更精细的熔锥型光纤耦合器的模型.     

单模双包层光纤之间的耦合

本文求得了单模双包层光纤之间耦合系数精确的解析表达式.计算了上升内包层、匹配包层和凹陷内包层光纤耦合系数随归一化频率V的关系曲线.也给出了不同V值的耦合系数随归一化距离(D/α)的关系曲线.该公式不但能够计算x偏振模的耦合系数,而且也能计算y偏振模的耦合系数.它可用于分析折射率差较大的光纤之间能量耦合以及耦合器的偏振特性.     

Apodized grating coupler using fully-etched nanostructures

A two-dimensional apodized grating coupler for interfacing between single-mode fiber and photonic circuit is demonstrated in order to bridge the mode gap between the grating coupler and optical fiber. The grating grooves of the grating couplers are realized by columns of fully etched nanostructures, which are utilized to digitally tailor the effective refractive index of each groove in order to obtain the Gaussian-like output diffractive mode and then enhance the coupling efficiency.Compared with that of the uniform grating coupler, the coupling efficiency of the apodized grating coupler is increased by 4.3% and 5.7%, respectively, for the nanoholes and nanorectangles as refractive index tunes layer.     

Crosstalks of two-waveguide and three-waveguide directional couplers

Crosstalks of two-waveguide and three-waveguide directional couplers are analyzed mathematically based on the relationship between the coupled mode and the normal mode. Numerical techniques such as the finite-difference method and the beam propagation method are employed to confirm the validity of the derived expressions. The calculation results show that two-waveguide directional coupler is superior to any type of three-waveguide couplers from the practical viewpoint of the crosstalk and the coupling length.     

二维光子晶体波导与单模平面介质波导间的喇叭波导接头

提出并优化了用于二维介质柱光子晶体波导与单模平面介质波导对接的基于分布布拉格反射波导的喇叭波导接头，提高了这两种波导之间的传输效率.二维时域有限差分仿真结果表明，在大部分光子晶体波导导模的频谱范围内，传输效率高于98％.传输效率最高可以达到99.85％. 关键词： 光子晶体波导 平面介质波导 时域有限差分     

Irreversible coupling by use of dissipative optics

The time reversibility of optical propagation impedes the definite performance of many optical devices, such as couplers, polarization converters, etc. We suggest a novel concept in which we use media with loss and gain, thus breaking the time-reversal characteristics, to achieve a unidirectional optical mode interference and coupling, which is a desirable feature for light-wave circuits. Using a matched periodic modulation of both the index of refraction and loss (gain) of the medium, we implement a spatially single sideband perturbation, which breaks the symmetry to allow only a unidirectional energy transfer from mode m to mode n of the optical structure. We elaborate on this phenomenon in coupling between two modes of a multimode optical waveguide.     

Apodized fully-etched surface grating coupler using subwavelength structure for standard silicon-on-insulator waveguide

We design and demonstrate the fully-etched apodized grating couplers based on the silicon-on-insulator (SOI) platform using subwavelength structure for both transverse electric (TE) and transverse magnetic (TM) modes operation. The subwavelength grating (SWG) is used to engineer the refractive index using second-order effective medium theory (EMT). The whole designing procedure is given in details, especially a feasible and programmable method is developed to precisely manipulate the coupling strength of each grating cycle. A perfect Gaussian output beam can be synthesized for the TE mode operation, achieving a field overlap up to 98.3% with the Gaussian fiber mode. The simulated peak coupling losses are ?4.63 and ?2.99 dB for the TE mode and the TM mode, respectively, which are comparable with conventional shallowly etched grating couplers, realizing a fabrication simplification without performance penalty. The measured peak coupling loss is ?7.6 dB for the TE mode coupler with a 1 dB bandwidth of 45 nm, and ?6.1 dB for the TM mode coupler with a 1 dB bandwidth of 34 nm.     

应用耦合模理论研究光在圆对称双包层光纤中的传输

为了深入理解双包层光纤的光场传输特性,应用耦合模理论将双包层光纤等效为相互耦合的单模光纤和环形芯光纤,研究了圆对称的双包层光纤的光场传输.通过计算单模光纤LP01模和环形芯光纤导模的耦合系数发现了环形芯光纤LP0n模的耦合系数远大于其它导模的耦合系数,且LP0n模中的高阶模比低阶模的耦合系数大.据此,应用耦合模理论计算得到了该双包层光纤的光传输特性,计算结果发现光场沿光纤轴向呈近似周期分布,且纤芯中光功率变化的平均周期随波长递增,但平均归一化功率与光纤参数紧的选择有关.     

应用耦合模理论研究光在圆对称双包层光纤中的传输(英文)

为了深入理解双包层光纤的光场传输特性,应用耦合模理论将双包层光纤等效为相互耦合的单模光纤和环形芯光纤,研究了圆对称的双包层光纤的光场传输.通过计算单模光纤LP01模和环形芯光纤导模的耦合系数发现了环形芯光纤LP0n模的耦合系数远大于其它导模的耦合系数,且LP0n模中的高阶模比低阶模的耦合系数大.据此,应用耦合模理论计算得到了该双包层光纤的光传输特性,计算结果发现光场沿光纤轴向呈近似周期分布,且纤芯中光功率变化的平均周期随波长递增,但平均归一化功率与光纤参数紧的选择有关.     

New side-pump scheme for large mode area fiber lasers by wrapping polished fibers conjugate caustic removed

With the purpose of uniform gain coefficient along the axial direction in the core of gain guided and index anti-guided fiber, a new kind of side-pump scheme by wrapping particularly treated fibers around the central GGIAG fiber is reported in this paper. According to leakage mode analysis on wrapped fiber and numerical simulation on this pumping structure having ytterbium doped central fiber and conventional wrapped side fiber, we find this kind of pump scheme can improve the uniformity of gain coefficient along the fiber direction, and also, it can support multi channels of pumping sources by adding more side fibers to improve the total effective incident pumping power.     

Experimental mode coupling analysis in optical waveguides for sensor and component optimization

A computer controlled mode coupling analyser is conceived and described in detail to characterize and to analyse mode coupling in all known kinds of cylindrical, multimode, step index, optical waveguides (CMSIOWs) by experimental measurement. These waveguides can be present in many ways like simple fibres, multimode fibre-optic sensors (MFOS) or other optical components like couplers or modulators. The computer processed results of measurements lead to transfer matrices and modulation transfer matrices. The transfer matrices describe the light distribution in the far field of these waveguides depending on the direction and power of the light that is injected into it. By visualizing the modulation transfer matrices in the form of mesh diagrams, the influence of external physical parameters, like a measured variable, on the mode coupling mechanisms inside CMSIOWs can be shown directly. The computer controlled mode coupling analyser will make the optimization of MFOS more efficient and, moreover, it will ease modelling of CMSIOWs and define their properties. The potential field of applications for the mode coupling analyser will be in engineering and optimization of intrinsic multimode fibre-optic sensors and their components.     

Directional coupler wavelength selective filter based on dispersive Bragg reflection waveguide

A new type of wavelength selective filter, based on high differential dispersion between two coupled waveguides, is presented. The Bragg Reflection Waveguide displays high effective refractive index dispersion, due to the interaction of the guided mode with the two confining Bragg reflectors. When coupled with a weakly guided buried channel silica waveguide, a very narrow bandwidth filter (<1 nm) can be easily produced, in a shorter length, with respect to directional couplers made with standard step index channel waveguides. The complete design methodology, fabrication and characterization are presented.     

Terahertz antiresonant-reflecting-hollow-waveguide-based directional coupler operating at antiresonant frequencies

We report a particular coupling phenomenon occurring in the directional coupler composed of two touching terahertz antiresonant reflecting hollow waveguides. Unlike conventional directional couplers where one even system mode and one odd system mode are excited, numerical results indicate that three (one even and two odd) system modes participate in the power transfer process at the antiresonant frequencies. As a result, the coupling length can be significantly reduced, and it is shown here to be less than 300 wavelengths.     

Analysis of rectangular-core waveguide structures and directional couplers by an iterated moment method

Using an iterated moment method (weighted index method), formulae are derived for the accurate calculation of the dispersion characteristics and field distributions of guided modes in strip dielectric waveguides and strip-loaded waveguides, and for the calculation of the coupling length of rectangular-core dual-channel directional couplers. The formulae are simple and the results obtained by the present analysis agree well with computer-aided exact numerical analysis. This method can be readily extended to the analysis of other dielectric waveguide structures.     

无需隔离器的单向运行光纤环形激光器的研究

从理论上设计并从实验上实现了一种简单易行的环形谐振腔结构,它仅由两个耦合器连接成一个环形谐振腔,可以使得逆时针运行光的增益高于顺时针运行光的增益,其比值取决于两个耦合器耦合比的选取。将此作为掺铒光纤激光器的谐振腔,由于两个相反方向具有不同的损耗,因而可以实现在不需要隔离器的情况下也能保证激光的单向运行,从而简化了器件结构,消除隔离器的插入损耗,降低了成本。在实验的过程中使用两个3dB耦合器,结果表明,在阈值及其以上抽运功率下,两个相反方向的输出功率差始终大于17dBm,基本实现了激光的单向运行。     

Long period grating in/on planar and channel waveguides: A theory description

A comprehensive, complete theory suitable for a long period grating (LPG) on/in a planar or channel waveguide is described on the basis of coupled mode theory. The theory aims at key characteristic parameters with respect to the effect of the LPG, including resonance wavelength, transmission power of the guided mode in the waveguide, full-width at half-maximum (FWHM) of the power attenuation band in transmission spectrum of the guided mode, and coupling coefficient between a guided and a coupled mode. The type of the grating including relief and index modulation, different polarization state combinations of the guided mode and the resonant mode, and slanted grating structure are considered in this theory. The influences of the coupling between two guided modes and between a guided mode and a substrate mode are discussed. The role of cladding layer in a long period waveguide grating is demonstrated in particular. Finally, the expressions for the sensitivity of resonance wavelength as a function of external temperature, pressure and surrounding refractive index are derived.     

掺铒孔辅助导光光纤的特性研究与优化设计

掺铒孔辅助导光光纤是由掺铒的高折射率纤芯、低折射率包层和少量的空气孔组成. 采用有限元法分析了掺铒孔辅助导光光纤的模式特性；给出了数值计算截止波长和模场直径的方法；提出了改进的平均粒子数反转度迭代算法来数值计算掺铒光纤放大器的增益和噪声系数. 研究空气孔对掺铒孔辅助导光光纤的截止波长、模场直径和放大器的增益系数的影响. 发现：减小相对孔芯距的值，可使截止波长向短波长移动，减小模场直径的值；当孔的相对大小较大时，截止波长、模场直径和增益的最大值基本上不随孔的相对大小的增大而改变. 最后，综合考虑掺铒光纤基模和二阶模的截止波长、与普通单模光纤的熔接损耗、放大器的增益和噪声系数等因素，优化设计了掺铒孔辅助导光光纤的四个结构参量——纤芯半径、纤芯与包层的折射率差、相对孔芯距和孔的相对大小. 关键词： 孔辅助导光光纤 掺铒光纤 光纤放大器 有限元法     

一种改进的2×2 SOI Mach-Zehnder热光开关

本文设计并制作了基于强限制多模干涉耦合器的2×2 SOI马赫-曾德热光开关.这种光开关采用了深刻蚀结构的多模干涉耦合器和输入/输出波导,较大地提高了干涉耦合器的性能并减少了连接耦合损耗.同时,在调制臂区域采用浅刻蚀结构,保持其单模调制状态.深刻蚀多模干涉耦合器具有优越的特性,在实验中测得不均衡度只有0.03 dB,插入损耗－0.6 dB.基于这种耦合器的新型热光开关,其插入损耗为－6.8 dB,其中包括光纤-波导耦合损耗－4.3 dB,开关时间为6.8 μs.     

刻蚀光纤布拉格反射器特性的理论分析

从理论上研究了波导耦合型刻蚀光纤布拉格反射器的特性。采用正交模式耦合理论描述其中的光栅辅助正反向模式耦合，用非正交模式耦合理论描述输入输出接口的模式激发，给出了分析耦合波导布格瓣反射器的角析表达式，分析表明刻光张布拉格反应器中存在三种布拉格反应，在频谱中表现为六个分立的反射峰，与实验结果相符，其反射率不仅决定事系数，还与其结构参数，尤其是Ａｌ２Ｏ３层的厚度，Ａｌ２Ｏ３层与光纤芯的距离以及匹配层折射