Boost up of four wave mixing signal in semiconductor optical amplifier for 40 Gb/s optical frequency conversion

The 40 Gb/s optical frequency converter for non-return to zero differential phase shift keying (NRZ-DPSK) signal by using four wave mixing in semiconductor optical amplifier (SOA) have achieved sucessfully. The optimized signal-to-pump ratio for NRZ-DPSK by using optimized SOA structure with enhanced FWM effect is also evaluated. The optimum signal-to-pump ratio is 12 dB and 10 dB with Q factor penalty of 0.685 dB and 0.663 dB. The dependence of four wave mixing efficiency and converted signal power on signal input power is studied and it is evaluated that four wave mixing efficiency decreases with increase in the input power. The impact of pump power, signal-to-pump ratio, and SOA parameters with Q factor penalty for 40 Gb/s has been illustrated. It has shown that converted signal power increases up to the saturation power of semiconductor optical amplifier, then decreases. It is observed that for the optimum pump power, OSNR of converted signal varies little with signal input power.     

Performance comparison between digital back propagation (DBP) and pilot-aided method for fiber nonlinearity compensation in different fiber links

We numerically investigate and compare the performance of fiber nonlinearity compensation using digital back propagation (DBP) method and pilot-aided method in coherent optical transmission systems using different fiber links. Simulations for wavelength division multiplexed (WDM) 112 Gb/s polarization division multiplexed quadrature phase shift keying (PDM-QPSK) systems with dispersion unmanaged (no DM) and dispersion managed (DM) fiber links are implemented. System Q-factor and maximum transmission distance at bit error rate (BER) of 3.8 ÿ 10^?3 are calculated for performance comparison. The results show that, for system with no DM fiber link, DBP method outperforms pilot-aided method, because DBP method has better performance for intra-channel fiber nonlinearity compensation. However, for system with DM fiber link where inter-channel fiber nonlinearity plays an important role, pilot-aided method performs better than DBP method, because of its ability for inter-channel fiber nonlinearity compensation.     

Tunable all-fiber intracavity wavelength converter without external pumps

A new architecture for tunable broadband wavelength conversion in a dispersion-shifted fiber is presented. Conversion is achieved by using four-wave-mixing in a dispersion-shifted fiber in a single fiber-ring cavity. Wide tunability is achieved by the self-generation of two tunable orthogonal pumps in the cavity. This effect is due to the introduction of two tunable fiber Bragg gratings written in high birefringence fibers which act as selective polarization and wavelength filters. The results show conversion efficiencies up to −2 dB with the signal-to-noise ratio of the converted signal up to 26 dB.     

Simulative analysis of pre- and post-compensation using CRZ format in WDM optical transmission link

This paper reports the effects of pre- and post-compensation using CRZ modulation format in long-haul WDM optical transmission link using wavelengths in three bandwidths viz. 1537.4; 1550; 1562.6 nm at per channel bit rates of 10 Gbit/s. It has been investigated here that optimization of dispersion map results in improved management of nonlinear effects in long-haul light wave systems operating in the quasi-linear regime. In addition, pre- and post-dispersion compensation was applied at the transmitter and receiver depending on the signal wavelength, which resulted in improvement of performance metrics viz. Q² (dB), BER and OSNR over longer transmission distances. It is reported here that optimum values of Q² dB of 17.1 dB, BER of 8.4933e⁻⁰¹⁵ and OSNR of 30.1 dB are obtained at 1550 nm at a transmission distance of 7360 km with pre- and post-compensation using CRZ modulation format.     

基于光纤简并四波混频的可调谐波长转换器的优化设计

分析了光纤零色散波长、光纤长度、信号光频率及泵浦功率对基于光纤简并四波混频的可调谐波长转换器调谐带宽和转换效率的影响.结果表明对应不同的零色散波长都存在唯一的最优信号光频使得调谐带宽达到最大,进而推导了最优信号光频和最大调谐带宽的解析表达式,给出了提高此类器件调谐带宽和泵浦效率,减少调谐中输出信号功率起伏的优化设计方法.与以往实验结果相比优化后同等泵浦功率下调谐带宽可增加10 nm,若保证同样的调谐带宽则可将泵浦功率降低4.6 dB.     

Widely tunable femtosecond fiber optical parametric oscillator

The phase-matching condition in a fiber is discussed. A balance among the different orders of fiber dispersion can be found to achieve a widely tuning modulation instability gain for pumping around the normal dispersion regime. Three coupled nonlinear wave equations are used to simulate the femtosecond fiber optical parametric oscillator. The numerical results show that, through appropriate choice of dispersion, femtosecond pulses with a 180-nm tunable range can be generated when pump wavelength near a fiber’s zero-dispersion wavelength is tuned only 7 nm. Further tuning is limited by the walk-off between the pump and the signal pulses.     

基于光纤简并四波混频的可调谐波长转换器的优化设计

分析了光纤零色散波长、光纤长度、信号光频率及泵浦功率对基于光纤简并四波混频的可调谐波长转换器调谐带宽和转换效率的影响．结果表明对应不同的零色散波长都存在唯一的最优信号光频使得调谐带宽达到最大,进而推导了最优信号光频和最大调谐带宽的解析表达式,给出了提高此类器件调谐带宽和泵浦效率,减少调谐中输出信号功率起伏的优化设计方法．与以往实验结果相比优化后同等泵浦功率下调谐带宽可增加10nm,若保证同样的调谐带宽则可将泵浦功率降低4．6dB．     

Supercontinuum generation in ultra-flat near zero dispersion PCF with selective liquid infiltration

We present a new design study of ultra-flat near zero dispersion PCF with selectively liquid infiltration with all uniform air-holes in the cladding. The dependence of the individual parameters upon dispersion has been presented in detail. The study establishes that varying Λ influences the total dispersion, whereas d has the desired effect of modifying the dispersion slope, and varying n_L modifies both. With the above study we could achieve near zero ultra-flat dispersion as small as 0 ± 0.41 ps/nm/km for broad wavelength range of 452 nm. The optimized near zero ultra-flat dispersion PCF has been targeted for smooth and flat broadband spectrum supercontinuum generation (SCG) for near Infrared (IR) applications. Broadband SC generations corresponding to three different designs of ultra-flat dispersion fiber have been carried out by using picoseconds pulse laser around the first zero dispersion wavelengths (ZDW). The numerical results show that FWHM of around 400 nm with less than a meter long fiber can be achieved with these fibers that cover most of the communication wavelength bands. The proposed design study will be applicable for applications in the field of tomography, Dense Wavelength Division Multiplexing (DWDM) system, spectroscopy, etc.     

Experimental investigation of supercontinuum generation in highly nonlinear dispersion-shifted fiber pumped by spectrum-sliced amplified spontaneous emission

Spectral broadening of spectrum-sliced amplified spontaneous emission (SS-ASE) in highly nonlinear, dispersion-shifted fiber in different dispersion regimes is investigated experimentally. We find that, the spectral noise of the amplified SS-ASE pump from Er³⁺-doped fiber amplifier seeds the spectral broadening via four-wave mixing or modulation instability. Stimulated Raman scattering, red-shifted Raman solitons, and blue-shifted dispersion waves all enhance the broadening of the spectrum. The effect of the polarization state of pump on supercontinuum generation is also investigated, and it is found that, linear polarization is more efficient than random polarization for pumping supercontinuum. Supercontinuum with −10 dB bandwidth of 200 nm is generated by launching linearly polarized pump with 33.5 dB m power into anomalous dispersion regime near to zero dispersion wavelength of fiber.     

High-Q, tunable, photonic microwave single passband filter based on stimulated Brillouin scattering and fiber Bragg grating filtering

We experimentally demonstrate a single passband, photonic microwave bandpass filter scheme based on stimulated Brillouin scattering (SBS) in optical fiber. A single side band (SSB)-modulated probe and a single frequency, tunable pump beam that have been produced by the combination of conventional Mach-Zehnder modulators and fiber Bragg grating filters, are used for the generation of SBS phenomenon in a 1-km long highly nonlinear dispersion-shifted optical fiber. Using the proposed scheme a single microwave passband with a ∼26 MHz bandwidth is readily achieved over a radio frequency tuning range from 1.3 to 9.3 GHz. The maximum Q-factor is measured to be ∼360.     

Electrical nonlinearity pre-compensation for CO-OFDM system

An electrical nonlinearity pre-compensation (ENPC) combined nonlinearity with chromatic dispersion method is introduced for coherent optical orthogonal frequency-division multiplexing (CO-OFDM) system. Comparing with existed only nonlinearity pre-compensation (NL Pre-comp) method, ENPC method is not only suitable for low-dispersion fiber system, but also effective for high dispersion fiber transmission system without optical dispersion compensation. For 40 Gbit/s 20 × 80 km standard single mode fiber (SSMF) system, ENPC method can improve the nonlinear threshold (NLT) (for Q > 10 dB) about 2.7, 1.2, and 1.0 dB, and the maximum Q factor about 1.2, 0.4, and 0.3 dB for 2, 8, and 16 ps/nm/km fiber systems, respectively. The method allow the CO-OFDM system can avoid using optical dispersion compensation even for high dispersion fiber system with higher input power, and the 2-step ENPC solution does not increase more computation complexity compared with NL pre-comp method.     

Determination of nonlinear coefficient and group-velocity-dispersion of bismuth-based high nonlinear optical fiber by four-wave-mixing

Nonlinear coefficient and group-velocity-dispersion of bismuth-based nonlinear fibers were determined by four-wave-mixing measurements. The wavelength dependence of refractive index of bulk bismuth-based glasses was also measured to estimate the material dispersion and waveguide dispersion. A newly developed bi-directional four-wave-mixing configuration enabled us to determine all fiber parameters simultaneously. The obtained fiber nonlinearity γ ∼ 1000 W⁻¹ km⁻¹ of bismuth-based nonlinear fiber is the highest one in the step-index fiber made of oxide glasses as expected from a high refractive index at 1550 nm. Dispersion analysis reveals that the both material dispersion and waveguide dispersion affect to the large group-velocity-dispersion of bismuth-based nonlinear fiber.     

Switchable and tunable dual-wavelength ultrashort pulse generation in a passively mode-locked erbium-doped fiber ring laser

A simple switchable and tunable dual-wavelength passively mode-locked erbium-doped fiber ring laser based on nonlinear polarization rotation (NPR) effect is proposed and experimentally demonstrated. The NPR effect effectively induces wavelength- and intensity-dependent loss to readily implement stable dual-wavelength passively mode-locked operation. The wavelength switching and tuning of the dual-wavelength ultrashort pulse laser are achieved only by appropriately rotating the polarization controllers. The side-mode suppression ratio of the output pulse is larger than 41 dB over a wavelength-tuning range of 43.4 nm. Moreover, triple-wavelength ultrashort pulse can also be observed.     

Reduction of the fiber nonlinearity impairment using optical phase conjugation in 40 Gb/s CO-OFDM systems

In this paper, optical phase conjugation (OPC) located in the transmitter based on four wave mixing (FWM) in a semiconductor optical amplifier (SOA) is first simulated in 40 Gb/s CO-OFDM systems, and the fiber nonlinearity impairment of the transmission link is precompensated before OPC by transmission through a fiber with large nonlinearity coefficient. Simulation results show that the nonlinear threshold (NLT) can be increased by about > 3 dB and maximum Q factor can be increased by about 2 dB for the single-channel system. For 50-GHz-Spacing WDM systems, the maximum Q and NLT are increased by about 1 dB, even in the presence of cross phase modulation (XPM) from neighbouring WDM channels. It is found that this OPC subsystem located in the transmitter, not necessary to be inserted into the middle of link, can mitigate the fiber nonlinearity impairment for both single-channel and WDM systems.     

Performance analysis of dense wavelength division multiplexing secure communications with multiple chaotic optical channels

The performance of dense wavelength division multiplexing secure communications with multiple chaotic optical channels is numerically analyzed in this paper. Taking the multiplexing of three chaotic optical channels as an example, we investigate the effects of second-order dispersion coefficient and nonlinear coefficient of fiber, channel spacing, message amplitude and bit rates on chaotic synchronization and multiplexing communications. Chaotic synchronization quality and Q-factor of the recovered message decrease with the increasing fiber length. A 1.25 Gbits/s non-return-to-zero (NRZ) sequence can be securely transmitted up to 60 km under the influence of the other two chaotic optical channels. Compared with the fiber dispersion, the cross-phase modulation is the primary factor which deteriorates the quality of communications. The results also show that the quality of communications is unlimited to the channel spacing as long as chaotic synchronization can be maintained. In addition, the effect of the amplitude of encrypted message on Q-factor and the confidentiality is demonstrated.     

Investigation of wavelength division multiplexing ring network topology to enhance the system capacity

In this paper, we have investigated the wavelength division multiplexed (WDM) system using ring network topology. This network is used to increase the capacity with eight optical add/drop multiplexers (OADMs) by using dispersion compensating fiber and semiconductor optical amplifier (SOA) to achieve a distance up to 1600 km. It is observed that network shows the acceptable results at 15 Gbps data rate with 100 GHz channel spacing. The OADM nodes are also varied to investigate the network performance in the term of BER and Q-factor.     

Fabrication of low OH loss holey fibers with varying air hole sizes and their optical properties

We experimentally investigate a flexible fabrication technique for low OH and transmission losses holey fibers with a Ge-doped core and air holes in a silica cladding region. Versatile holey fibers of different size, pitch, and shape of air holes were achieved by controlling the temperature and heating time of the holey fiber preform. In addition, we suppress the OH loss of less than ∼0.323 dB/km at 1383 nm. After fabricating holey fibers, we measure their optical properties including cut-off wavelength, mode field diameter, splicing loss, dispersion, bending loss, and polarization dependent loss based on the size of air holes. The total transmission loss was measured to be ∼0.226 dB/km at 1550 nm by improving the fabrication process. After fabricating optical patch cord based on holey fibers, we measured the long-term stability of the fabricated holey fiber by using the temperature cycling technique for 24 and obtained low power fluctuation of 0.2 dB. We achieve the high quality holey fiber with a low bending loss of ∼0.04 dB/turn under a bending radius of 2.5 mm at 1550 nm. We also obtain a tunable band rejection filter with a number of bending turns.     

Multi parameter optimization of Raman Fiber Amplifier using genetic algorithm for S band dense wavelength division multiplexed system

A simple genetic algorithm is implemented to perform multi parameter optimization of Raman Fiber Amplifier for 100 channel S band dense wavelength division multiplexed system at 25 GHz interval. A cost effective system using single Raman pump is investigated aiming at maximum average gain. The single counter propagating pump is optimized to frequency of 211.528 THz and 652.93 mW power level with optimum Raman fiber length of 44.064 Km. There is evidence to show that the optimum solution presents a small gain variation (less than 3 dB) over an effective bandwidth covering 197–199.475 THz. The optimized configuration enabled an adequate system performance in terms of acceptable Q-factor (19.52 dB) and BER (1.46 × 10⁻²¹).     

Tunable and switchable multi-wavelength Erbium-doped photonic crystal fiber ring laser incorporating a length of highly nonlinear photonic crystal fiber

A tunable and switchable multi-wavelength Erbium-doped photonic crystal fiber ring laser incorporating a length of single-mode highly nonlinear photonic crystal fiber is proposed and demonstrated experimentally. Stable dual-wavelength and triple-wavelength operations at room temperature are achieved by employing the highly nonlinear photonic crystal fiber to induce four-wave mixing effect and a polarization controller to vary the polarization states of propagation lights in the laser cavity. The laser cavity is free from any wavelength selection components. The laser obtains maximal 30 dB signal-to-noise ratio and the peak power fluctuations of lasing lines are less than 1.39 dB.     

Measurement of nonlinear coefficient of a highly nonlinear fiber based on peak four-wave mixing signal generation conditions

We introduce a new measurement method of the nonlinear coefficient (NC) of a highly nonlinear fiber based on a four-wave mixing (FWM) technique. The NC along with the fiber's zero-dispersion wavelength (ZDW) was determined from the precise measurement of the pump power dependent optimum pump frequency for peak FWM signal generation conditions. The measurement errors of the NC and ZDW values determined with this method were less than 4.6% and 0.051 nm, respectively.