Electrocatalytic Determination of the antibiotic Levofloxacin using modified carbon paste electrode with a poly-murexide thin film voltammetrically

In this work, a simple, cheap, sensitive, and selective modified carbon paste electrode is proposed for the electroanalytical determination of Levofloxacin (LEVO), the drug used to treat pneumonia caused by coronavirus. The electrochemical polymerization method was applied to create a thin poly-murexide film (POMUR) on the bare carbon paste electrode (BCPE) surface to enhance its electrocatalytic activity. The peak current response of LEVO obtained by POMUR/CPE was increased by 14.2 μA compared to BCPE. Scanning electron microscopy (SEM) and cyclic voltammetry (CV) techniques were employed to characterize BCPE and POMUR/CPE. Under the optimal experimental circumstances, the prepared sensor was capable of determining LEVO with a low limit of detection (LOD) of 7.18 nM (S/N = 3) for a linear dynamic range of 25 – 1 × 10³ nM utilizing differential pulse voltammetry (DPV). Moreover, the practical applicability of POMUR/CPE for determining LEVO in pharmaceutical formulations and biological samples (human serum) demonstrated high sensitivity and selectivity with a recovery of 95.08 – 100.5 %.     

Electrochemical Detection of Para‐nitrophenol using Copper Metal Nanoparticles Modified Gold Electrode

para‐Nitrophenol (p‐NP) is a high priority environmental pollutant. For the sake of safety, sensitive detection of its presence in water resources and food is highly important. The present article describes the use of copper metal nanoparticles for selective and sensitive electrochemical detection of p‐NP in pure and real sample. For this the gold electrode was fabricated by polyvenylpyrrolidone stabilized copper metal nanoparticles (ca . 4 nm d.) via self‐assembled 4,4′‐bipyridine monolayer and characterized by microscopic and electrochemical techniques. The newly developed sensor permits for sensitive detection of p‐NP in a linear concentration range of 1–500 μM with lowest detection limit of 0.34 nM and high sensitivities 247.1 μA cm⁻² μM⁻¹. The sensor electrode exhibited high stability, reproducibility, good selectivity in the presence of potential interfering agents and had an excellent capability for the selective determination of p‐NP in river water without preliminary treatments.     

Adsorptive Stripping Voltammetric Determination of Imipramine and Amitriptiline at a Nanoclay Composite Carbon Ionic Liquid Electrode

A new carbon nanocomposite electrode has been designed by incorporation of montmorillonite nanoclay into a carbon ionic liquid electrode for the electrochemical determination of imipramine (IMP) and amitriptyline (AMT). They are expected to accumulate on the electrode surface through the cooperative interaction of ionic liquid and clay with the drugs. The proposed electrode also possesses attractive electrocatalytic effects towards the drugs especially AMT. Low detection limits of 19 nM for IMP and 24 nM for AMT were achieved. The proposed nanocomposite electrode exhibits good applicability for monitoring IMP and AMT in pharmaceutical formulations and blood serum samples.     

Construction of a carbon nanocomposite electrode based on amino acids functionalized gold nanoparticles for trace electrochemical detection of mercury

A simple, highly sensitive and selective carbon nanocomposite electrode has been developed for the electrochemical trace determination of mercury. This mercury nanocomposite sensor was designed by incorporation of thiolated amino acids capped AuNps into the carbon ionic liquid electrode (CILE) which provides remarkably improved sensitivity and selectivity for the electrochemical stripping assay of Hg(II). Mercury ions are expected to interact with amino acids through cooperative metal–ligand interaction to form a stable complex which provides a sensitive approach for electrochemical detection of Hg(II) in the presence of other metal ions. The detection limit was found to be 2.3 nM (S/N = 3) that is lower than the permitted value of Hg(II) reported by the Environmental Protection Agency (EPA) limit of Hg(II) for drinkable water. The proposed nanocomposite electrode exhibits good applicability for monitoring Hg(II) in tap and waste water.     

Fabrication and characterization of poly 2-napthol orange film modified electrode and its application to selective detection of dopamine

The present work is based on the use of a redox mediator containing an azo group for the selective determination of dopamine in the presence of uric acid and ascorbic acid by electrochemical method. A modified electrode was prepared by electrochemical polymerization of the poly 2-napthol orange film (P2NO) on the paraffin wax-impregnated graphite electrode (PIGE) by applying potential between ?0.6 and 0.8 V at scan rate of 50 mV s^?1 for 30 segments. The modified P2NO film electrode was characterized by ATR-IR spectroscopy, FE-SEM, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), differential pulse voltammetry (DPV), hydrodynamic voltammetry (HDV), and chronoamperometry (CA). The P2NO film modified electrode exhibited selective determination of dopamine in the presence of uric acid and ascorbic acid, and the electrocatalytic activity for oxidation of dopamine was excellent. The linear range for the determination of dopamine was 0.6 to 250 μM with a limit of detection of 0.13 μM. The modified P2NO electrode showed good stability and reproducibility. The modified electrode was used for real sample analysis such as human blood serum, rat blood serum, and pharmaceutical samples (dopamine hydrochloride injection). The results obtained were found to be satisfactory.     

A Facile Fabrication of Poly-ethionine Film on Glassy Carbon Electrode for Simultaneous and Sensitive Detection of Dopamine and Paracetamol

An electrochemical sensor based on poly-ethionine (Poly-ET) film modified glassy carbon electrode was developed for sensitive and simultaneous sensing of dopamine (DA) and paracetamol (PA). The electropolymerization of ethionine monomer was carried out to modify the electrode. The modified electrode was characterized by using scanning electron microscopy, cyclic voltammetry and electrochemical impedance spectroscopy. The Poly-ET/GCE exhibited excellent electrocatalysis towards the sensing of DA and PA. Poly-ET/GCE showed a linear increase of current response with increase concentration of DA and PA ranging from 0.1 μM–60 μM and 0.1 μM–180 μM, respectively. The LODs were found to be 7 nM and 18 nM (S/N=3) for DA and PA, respectively. This electrochemical sensor was successfully utilized for the detection of DA and PA in pharmaceutical samples.     

Development of an Electrochemical Sensor for Selective Determination of Dopamine Based on Molecularly Imprinted Poly(p-aminothiophenol) Polymeric Film

In this study, a molecularly imprinted electrochemical sensor (MIP/DA) was investigated for selective and sensitive determination of dopamine (DA) by electrochemical polymerization of p-aminothiophenol in the presence of DA on gold electrode. According to electrochemical behaviour of the sensor, gained through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), MIP/DA sensor showed distinctive electron transfer characteristics in comparison to the non-imprinted (NIP/DA) sensor. Besides the MIP/DA sensor showed high selectivity for dopamine through its analyte specific cavities. The sensor had a broad working range of 5.0×10⁻⁸–2.0×10⁻⁷ M with a limit of detection (LOD) of 1.8×10⁻⁸ M and the developed sensor was successfully applied for determination of dopamine in pharmaceutical samples.     

An Electrochemical Robotic System for Routine Cathodic Adsorptive Stripping Analysis of Ni2+ Ion Release from Corroding NiTi Shape Memory Alloys

Cathodic adsorptive stripping voltammetry (AdSV) as highly sensitive and selective method for quantifying trace amounts of dissolved Ni²⁺‐ions has been integrated into an electrochemical robotic device using the wells of microtiter plates as low‐volume electrochemical cells. A three‐electrode assembly integrating a Bismuth film‐modified glassy carbon electrode as working electrode and a glass capillary for delivering Ni²⁺ standard solution in conjunction with an adapted software allowed multiple AdSV measuring cycles to be performed one after the other in the individual compartments of a 24‐well microtiter plate. Of advantage for the automation was the possibility of an in‐well electrochemical removal of used and a replating of fresh Bi films in between distinct measuring cycles. With optimized parameters for the accumulation of the complex between Ni²⁺‐ions and dimethylglyoxime onto the surface of the Bi film electrode and the subsequent stripping procedure, automated adsorptive stripping voltammetry in the established system offered a linear dynamic range of up to 170 nM, a sensitivity of 12 nA/nM Ni²⁺ and a limit of of detection of 2.1 nM (N=16) for the detection of trace levels of Ni²⁺‐ions. Automated AdSV certainly is of convenience for studying larger number of samples due to the high‐throughput capability of the robotic apparatus. As example, the automatic quantification of Ni²⁺‐ion release from electropolished surfaces of NiTi shape memory alloys during corrosion in NaCl solutions is described.     

Graphene Functionalized Graphite Electrode with Diphenylacetylene for Sensitive Electrochemical Determination of Adenosine‐5′‐triphosphate

In this paper a molecular wire modified carbon paste electrode (MW‐CPE) was firstly prepared by mixing graphite powder with diphenylacetylene (DPA). Then a graphene (GR) and chitosan (CTS) composite film was further modified on the surface of MW‐CPE to receive the graphene functionalized electrode (CTS‐GR/MW‐CPE), which was used for the sensitive electrochemical detection of adenosine‐5′‐triphosphate (ATP). The CTS‐GR/MW‐CPE exhibited excellent electrochemical performance and the electrochemical behavior of ATP on the CTS‐GR/MW‐CPE was carefully studied by cyclic voltammetry with an irreversible oxidation peak appearing at 1.369 V (vs. SCE). The electrochemical parameters such as charge transfer coefficient (α) and electrode reaction standard rate constant (k_s) were calculated with the results of 0.53 and 5.28×10^?6 s^?1, respectively. By using differential pulse voltammetry (DPV) as detection technique, the oxidation peak current showed good linear relationship with ATP concentration in the range from 1.0 nM to 700.0 µM with a detection limit of 0.342 nM (3σ). The common coexisting substances, such as uric acid, ascorbic acid and guanosine‐5′‐triphosphate (GTP), showed no interferences and the modified electrode was successfully applied to injection sample detection.     

Design of poly-l-methionine–gold nanocomposit/multi-walled carbon nanotube modified glassy carbon electrode for determination of amlodipine in human biological fluids

The present paper describes a sensitive electrochemical detection of amlodipine (AMLO) at the poly-l-methionine–gold nanoparticles/multi-walled carbon nanotube modified glassy carbon electrode (PLM–GNPs/MWCNTs/GCE) by differential pulse voltammetry (DPV) technique at physiological pH 7.12. Cyclic voltammetry results demonstrate that the proposed electrode shows excellent electrocatalytic activity toward oxidation of AMLO. Kinetic parameters of the electrochemical reaction are calculated, and analytical variables such as MWCNT volumes, drug accumulation time, electropolymerization cycles and pH values are also optimized. Under optimal conditions, the linear range covering from 5 nM to 2.5 μM along with detection limit of 1 nM is obtained. Moreover, this method is successfully used to detect AMLO in pharmaceutical samples and biological fluids of a dosage received by the volunteer.     

Nickel oxide nanoparticles decorated graphene quantum dot as an effective electrode modifier for electrocatalytic oxidation and analysis of clozapine

In the present work, a novel, simple, and sensitive clozapine (CLZ) sensor was developed based on nickel oxide nanoparticle (NiO)-decorated graphene quantum dot (GQD)-modified glassy carbon electrode (NiO/GQD/GCE). NiO/GQD/GCE was prepared by simple electrodeposition, the electrochemical behavior of CLZ at the surface of the prepared electrode was studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV), and an improved reversibility and increased peak current with negative shift in the oxidation potential were observed at the proposed electrode. The effect of some experimental parameters has been examined, and based on the results, an electron transfer–chemical reaction–electron transfer mechanism has been proposed for CLZ electrooxidation. The differential pulse voltammetric response of the NiO/GQD/GCE was linear to the concentration of CLZ in the range of 3?×?10^?9 to 1?×?10^?6 M, and the detection limit was found to be 0.55 nM (S/N?=?3). The method has been successfully used for the selective determination of the CLZ amount in the pharmaceutical preparations and human serum samples with good accuracy and precision.     

Solidified floating organic drop microextraction for determination of trace amounts of zinc in water samples by flame atomic absorption spectrometry

A glassy carbon electrode was prepared that was coated with a composite film containing electropolymerized poly(amidosulfonic acid) and multi-walled carbon nanotubes. It was used to study the electrochemical response of procaine by differential pulse voltammetry. The results indicate that the electrode exhibits a remarkable improvement in the oxidation peak of procaine, and this led to a simple and sensitive method for the electroanalytical determination of procaine. The peak current is proportional to the concentration of procaine from 80 nM to 1.0 µM. The detection limit is 25 nM (S/N?=?3). The modified electrode was successfully applied to the direct determination of procaine in pharmaceutical formulations.     

Label-Free Electrochemical Sensor Based on Manganese Doped Titanium Dioxide Nanoparticles for Myoglobin Detection: Biomarker for Acute Myocardial Infarction

A label free electrochemical sensor based on pure titanium oxide and manganese (Mn)-doped titanium oxide (TiO₂) nanoparticles are fabricated and characterized for the sensitive detection of myoglobin (Mb) levels to analyze the cardiovascular infarction. Pristine and Mn-doped TiO₂ nanoparticles were synthesized via the sol-gel method and characterized in order to understand their structure, morphologies, composition and optical properties. The structural properties revealed that the pure- and doped-TiO₂ nanoparticles possess different TiO₂ planes. FTIR studies confirm the formation of metal oxide nanoparticles by exhibiting a well-defined peak in the range of 600–650 cm⁻¹. The values of the optical band gap, estimated from UV-Vis spectroscopy, are decreased for the Mn-doped TiO₂ nanoparticles. UV-Vis spectra in the presence of myoglobin (Mb) indicated interaction between the TiO₂ nanoparticles and myoglobin. The SPE electrodes were then fabricated by printing powder film over the working electrode and tested for label-free electrochemical detection of myoglobin (Mb) in the concentration range of 0–15 nM Mb. The fabricated electrochemical sensor exhibited a high sensitivity of 100.40 μA-cm^−2/nM with a lowest detection limit of 0.013 nM (0.22 ng/mL) and a response time of ≤10 ms for sample S3. An interference study with cyt-c and Human Serum Albumin (HSA) of the sensors show the selective response towards Mb in 1:1 mixture.     

Label‐Free Electrochemical Aptasensor for Determination of Chloramphenicol Based on Gold Nanocubes‐Modified Screen‐Printed Gold Electrode

An ultrasensitive label‐free electrochemical aptasensor was developed for selective detection of chloramphenicol (CAP). The aptasensor was made using screen‐printed gold electrode modified with synthesized gold nanocube/cysteine. The interactions of CAP with aptamer were studied by cyclic voltammetry, square wave voltammetry (SWV) and electrochemical impedance spectroscopy. Under optimized conditions, two linear calibration curves were obtained for CAP determination using SWV technique, from 0.03 to 0.10 µM and 0.25–6.0 µM with a detection limit of 4.0 nM. The aptasensor has the advantages of good selectivity and stability and applied to the determination of CAP in human blood serum sample.     

Electrochemical Detection of Epinephrine Based on a Screen-printed Electrode Modified with NiO−ERGO Nanocomposite Film

This study presents a new electrochemical sensor (NiO−ERGO/SPE) for sensitive and selective detection of epinephrine (EPI) on the screen-printed electrode (SPE) which is modified with a nanocomposite film consisting of electrochemically reduced graphene oxide and NiO nanoparticles. After surface functionalization, structural and electrochemical characterization of NiO−ERGO film, DPV signals of NiO−ERGO/SPE towards the oxidation of EPI exhibited a linear correlation in the concentration range of 0.025 μM to 175 μM with a detection limit of 0.015 μM, which reveals NiO−ERGO film is manifested a good electrocatalytic activity for EPI detection compared with the previous reports. The selectivity of NiO−ERGO film was also tested on a very wide scale of possible interferents (ascorbic acid, uric acid, dopamine, lactic acid, phenylalanine, tyrosine, tryptophan, Li⁺, Na⁺, K⁺, Ca²⁺, and Zn²⁺). Moreover, to evaluate the applicability of the proposed sensor for real sample analysis, NiO−ERGO/SPE was successfully utilized for the determination of EPI in pharmaceutical samples.     

Bifunctional polydopamine@Fe3O4 core–shell nanoparticles for electrochemical determination of lead(II) and cadmium(II)

The present paper has focused on the potential application of the bifunctional polydopamine@Fe₃O₄ core–shell nanoparticles for development of a simple, stable and highly selective electrochemical method for metal ions monitoring in real samples. The electrochemical method is based on electrochemical preconcentration/reduction of metal ions onto a polydopamine@Fe₃O₄ modified magnetic glassy carbon electrode at −1.1 V (versus SCE) in 0.1 M pH 5.0 acetate solution containing Pb²⁺ and Cd²⁺ during 160 s, followed by subsequent anodic stripping. The proposed method has been demonstrated highly selective and sensitive detection of Pb²⁺ and Cd²⁺, with the calculated detection limits of 1.4 × 10⁻¹¹ M and 9.2 × 10⁻¹¹ M. Under the optimized conditions, the square wave anodic stripping voltammetry response of the modified electrode to Pb²⁺ (or Cd²⁺) shows a linear concentration range of 5.0–600 nM (or 20–590 nM) with a correlation coefficient of 0.997 (or 0.994). Further, the proposed method has been performed to successfully detect Pb²⁺ and Cd²⁺ in aqueous effluent.     

Biosensor for bisphenol A leaching from baby bottles using a glassy carbon electrode modified with DNA and single walled carbon nanotubes

We have developed a biosensor for highly sensitive and selective determination of the endocrinic disruptor bisphenol A (BPA). It is based on glassy carbon electrode modified with calf thymus DNA and a composited prepared from single walled carbon nanotubes (SWNT) and Nafion. The interaction between BPA and DNA was studied by voltammetry. The binding constant was determined to be 3.55?×?10³ M^?1, and the binding site has a length of 4.3 base pairs. These electrochemical studies provide further information for a better understanding of the toxicity and carcinogenicity of BPA. Under optimal conditions, the biosensor displays a linear electrochemical response to BPA in the 10 nM to 20 μM concentration range, with a detection limit as low as 5.0 nM (at an S/N of 3). The method was successfully applied to the quantification of BPA in leachates from plastic baby bottles. Recoveries range from 94.0 % to 106.0 % which underpins the excellent performance of this SWNT-based DNA sensor.

Electrochemical determination of riboflavin using a synthesized ethyl[(methythio)carbonothioyl] glycinate monolayer modified gold electrode

The surface of a gold disk electrode, for the first time, was modified with a self-assembled monolayer of a synthesized compound, ethyl [(methythio)carbonothioyl] glycinate (ECTG), for construction of an electrode sensitive to riboflavin (vitamin B₂). The electrochemical properties of the monolayer assembled on the gold disk were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. Under the optimized conditions, the voltammetric peak currents resulting from vitamin B₂ (VB₂) species were linear for VB₂ concentrations in the range from 10^–6 to 10^–2 M. The effect of pH, type of buffer solution and scan rate on the response of the modified electrode was studied. The constructed electrochemical sensor responses very well to VB₂ in the presence of most common vitamins. Finally, the performance of the Au–ECTG modified electrode was successfully tested for electrochemical detection of VB₂ in a pharmaceutical sample.     

A lead(II) sensor based on a glassy carbon electrode modified with Fe3O4 nanospheres and carbon nanotubes

We have developed a highly sensitive and selective sensor for lead(II) ions. A glassy carbon electrode was modified with Fe₃O₄ nanospheres and multi-walled carbon nanotubes, and this material was characterized by scanning electron microscopy and X-ray diffraction. The electrode displays good electrochemical activity toward Pb(II) and gives anodic and cathodic peaks with potentials at ?496 mV and ?638 mV (vs. Ag/AgCl) in pH?6.0 solution. The sensor exhibits a sensitive and fairly selective response to Pb(II) ion, with a linear range between 20 pM and 1.6 nM, and a detection limit as low as 6.0 pM (at a signal-to noise ratio of 3). The sensor was successfully applied to monitor Pb(II) in spiked water samples.

ZrO2-Graphene-Chitosan nanocomposite modified carbon paste sensor for sensitive and selective determination of dopamine

A sensitive and stable electrochemical sensor was developed by modification of carbon paste electrode with ZrO₂/graphene/chitosan nanocomposite. The modified sensor served as a potential electrocatalytic platform for dopamine. Electrochemical impedance spectroscopy studies indicated reduction of charge transfer resistance at the modified electrode surface thereby facilitating the electron transfer process which resulted in higher current response to dopamine. The electrochemical behavior of dopamine at the modified electrode was studied using cyclic and square wave voltammetry. The maximum current response for the electro-oxidation of dopamine was observed at pH 7.4 and the process was realized to be diffusion controlled. The modified sensor demonstrated linearity in the range 1000–5000 nM, with high sensitivity (22 nA/nM), detection limit of 11.3 nM and selectivity for dopamine in the presence of ascorbic and uric acid which are found to co-exist with dopamine in physiological media. The method was employed for quantification of dopamine in a pharmaceutical formulation.