Adsorptive Stripping Voltammetric Detection of Tea Polyphenols at Multiwalled Carbon Nanotubes‐Chitosan Composite Electrode

This study reports the catalytic oxidation and detection of tea polyphenols (TPs) at glassy‐carbon electrode modified with multiwalled carbon nanotubes‐chitosan (MWCNTs‐CS) film. The adsorption of TPs at the surface of the MWCNTs through π–π conjugation prevents the aggregation of nanotubes and induces a stable MWCNTs suspension in water over 30 days. Based on the adsorptive accumulation of polyphenols at MWCNTs, TPs is sensitively and selectively detected by adsorptive stripping voltammetry. The accumulation conditions and pH effect on the adsorptive stripping detection were examined. The linear range was found to be 100 to 1000 mg L^?1 with a detection limit of 10 mg L^?1 (S/N=3) for 2.5 min accumulation. Additionally, the MWCNTs‐CS electrode is easily renewed by applying positive potential to remove the adsorbed TPs. This method was successfully applied to determine TPs in commercially available teas with satisfied result compared with that of conventional spectrometric analysis.     

Amperometric Detection of Morphine at Preheated Glassy Carbon Electrode Modified with Multiwall Carbon Nanotubes

A highly sensitive and fast responding sensor for the determination of morphine is described. The multiwall carbon nanotubes immobilize on preheated glassy carbon electrode (5 min at 50 °C) by gently rubbing of electrode surface on a filter paper supporting the carbon nanotubes.The results indicated that carbon nanotubes(CNTs) modified glassy carbon electrode exhibited efficiently electrocatalytic oxidation for morphine with relatively high sensitivity, stability and long life. Under conditions of cyclic voltammetry, the potential for oxidation of morphine is lowered by approximately 100 mV and the current is enhanced significantly (10 times) in comparison to the bare glassy carbon electrode at wide pH range (2–9). The electrocatalytic behavior is further exploited as a sensitive detection scheme for morphine determination by hydrodynamic amperometry. Under the optimized conditions the calibration plots are linear in the concentration range 0.5–150 μM with the calculated detection limit (S/N=3) of 0.2 μM and sensitivity of 10 nA/μM and a relative standard deviation (RSD) of 2.5% (n=10). The amperometric response is extremely stable, with no loss in sensitivity over a continual 30 min operation. Such attractive ability of multiwall carbon nanotubes (MWCNTs) modified GC electrode, suggests great promise for a morphine amperometric sensor. Finally the ability of the modified electrode was evaluated for simultaneous determination of morphine and codeine.     

A novel sensor for the determination of Hg2+ in waters based on octadentate ligand immobilized multi-walled carbon nanotube attached to paraffin wax impregnated graphite electrodes (PIGE)

Journal of Solid State Electrochemistry - In this work, the synthesised octadentate ligand immobilised multi-walled carbon nanotubes (MWCNTs) modified electrode as an electrochemical sensor of Hg2+...     

Sensitive and selective molecularly imprinted electrochemical sensor based on multi-walled carbon nanotubes for doxycycline hyclate determination

An electrochemical sensor for doxycycline hyclate(DC)detection with high sensitivity and good selectivity is reported.The sensor was fabricated by electro-polymerization of molecularly imprinted polymers(MIPs)in the presence of DC onto multi-walled carbon nanotubes modified glassy carbon electrode(MWCNTs/GCE).The MWCNTs can significantly increase the current response of the sensor,leading to enhanced sensitivity.The MIPs provide selective recognition sites for DC detection.The experimental parameters,such as the polymer monomer concentration,supporting electrolyte pH,the time for electro-polymerization and the incubation time of the sensor with DC were optimized.Under optimized experimental conditions,the sensor displayed a linear range of 0.05μmol/L-0.5μmol/L towards DC detection,with the detection limit of 1.3×10^-2μmol/L.The sensor was successfully applied for recovery test of DC in human serum samples.     

Novel Lu3+ Carbon Paste Electrode Based on Functionalized Multiwalled Carbon Nanotubes

A novel carbon paste ion selective electrode for determination of trace amount of lutetium was prepared. Modified (functionalized) multiwalled carbon nanotubes (f‐MWCNTs) were used for improvement of a lutetium carbon paste sensor response. MWCNTs have a good conductivity which helps the transduction of the signal in carbon paste electrode. In this work it is shown that introducing certain functional groups on MWCNTs can improve the electrode signals. The electrode composition of 20 % paraffin oil, 56 % graphite powder, 18 % ionophore and 6 % f‐MWCNTs showed the stable potential response to Lu³⁺ ions with the Nernstian slope of 21.1 (±0.3) mV decade^?1 over a wide linear concentration range of 1.0×10^?6–1.0×10^?1 mol L^?1. The electrode has fast response time (<15 s) and long term stability (about one month).     

Surface Polymers on Multiwalled Carbon Nanotubes for Selective Extraction and Electrochemical Determination of Rhodamine B in Food Samples

In this study, we combine magnetic solid phase extraction (MSPE), with the screen-printed carbon electrode (SPCE) modified by a molecular imprinted polymer (MIP) for sensitive and selective extraction and electrochemical determination of Rhodamine B in food samples. A magnetic solid phase extraction (MSPE) was carried out using magnetic poly(styrene-co-divinylbenzene) (PS-DVB) and magnetic nanoparticles (MNPs) synthetized on the surface of multiwalled carbon nanotubes (MWCNTs). An MIP was prepared on the surface of MWCNTs in the presence of titanium oxide nanoparticles (TiO₂NPs) modifying the SPCE for the rapid electrochemical detection of Rhodamine B. The MIPs synthesis was optimized by varying the activated titanium oxide (TiO₂) and multiwalled carbon nanotubes (MWCNTs) amounts. The MSPE and electrochemical detection conditions were optimized as well. The present method exhibited good selectivity, high sensitivity, and good reproducibility towards the determination of Rhodamine B, making it a suitable method for the determination of Rhodamine B in food samples.     

聚多巴胺/多壁碳纳米管/玻璃碳电极上多巴胺的电分析

基于多巴胺（DA）在多壁碳纳米管（MWCNTs）修饰玻璃碳（GC）电极上的电聚合,制得聚多巴胺(PDA)/MWCNTs/GC电极,并对该修饰电极进行了电化学阻抗谱 (EIS)和循环伏安法(CV)表征。 在该修饰电极上,DA呈现良好的电化学行为。在pH=7.4磷酸缓冲溶液中其氧化电流显著高于在裸电极上的响应,且能有效地抑制2.0 mmol/L抗坏血酸(AA)或K4Fe(CN)6的直接电化学响应,表明MWCNTs可增敏信号,且阳离子选择透过性PDA膜可抑制阴离子的电化学干扰。 采用CV实验检测DA,DA氧化的半微分伏安峰高(ipa-sd)与多巴胺浓度在0.08～1.76 μmol/L范围内呈线性关系,在无抗坏血酸和有0.5 mmol/L抗坏血酸共存时的线性回归方程分别为ipa-sd(μA/s1/2)=0.107+0.405c(μmol/L)（r2=0.986）和ipa-sd(μA/s1/2)=0.628+0.649c(μmol/L)(r2=0.992),检测限均为8.0×10-8 mol/L(S/N=3)。 该法用于盐酸多巴胺注射液中多巴胺的快速测定,结果满意。     

Application of Glassy Carbon Electrode Modified with a Bilayer of Multiwalled Carbon Nanotube and Polypyrrole Doped with Nitrazine Yellow for Voltammetric Determination of Naltrexone

A new sensitive electrochemical sensor was fabricated based on a layer by layer process. In this process the glassy carbon electrode (GCE) is first coated by a thin film of multiwalled carbon nanotubes (MWCNTs). In the next step, the electropolymerization of pyrrole in the presence of Nitrazine Yellow (NY) as a dopant anion is performed on the surface of the MWCNTs precoated electrode. The electrochemical response characteristics of the modified electrode toward naltrexone (NTX) were studied by means of linear sweep voltammetry (LSV). A remarkable increase (～19 times) was observed in the anodic peak current of NTX on the surface of the modified electrode relative to the bare GCE. The effects of experimental parameters on the electrode response such as, drop size of the cast MWCNTs suspension, pH of the supporting electrolyte, accumulation conditions and the number of cycles in the electropolymerization process were investigated. Under the optimum conditions, the modified electrode showed a wide linear response to the concentration of NTX in the range of 4.0×10^?8–1×10^?5 mol L^?1 with a detection limit of 12 nmol L^?1. The prepared sensor exhibited high sensitivity, stability and good reproducibility for the determination of NTX. This sensor was successfully applied for the accurate determination of trace amounts of NTX in pharmaceutical and clinical preparations.     

Performance of SLS/MWCNTs/PANI capacitor electrodes in a physiological electrolyte and in serum

We report a stainless steel/multi walled carbon nanotubes/polyaniline (SLS/MWCNTs/PANI) capacitor electrode capable of operating in a physiological electrolyte and in serum. The specific capacitance of SLS/MWCNTs/PANI reaches 401 F g(-1) in the physiological electrolyte and 326 F g(-1) in serum. The capacity loss at 6.4 μA mm(-2) over 2000 cycles is 10% in the physiological electrolyte and 21% in serum.     

聚甲苯胺蓝-(多壁碳纳米管/PDDA)_n杂化膜修饰印刷电极的制备及其对NADH的测定

利用静电层层组装的方式在印刷电极表面制备了(多壁碳纳米管/邻苯二甲酸二乙二醇二丙烯酸酯(PDDA))n多层膜,采用电位扫描电聚合法在修饰有多层膜的印刷电极表面聚合甲苯胺蓝,制备了聚甲苯胺蓝-(多壁碳纳米管/PDDA)n杂化膜修饰电极。扫描电镜实验表明,多壁碳纳米管均匀分布在杂化膜中,且多壁碳纳米管的掺杂使杂化膜表现出明显的多孔性。电化学实验表明,杂化膜具有良好的导电性且多壁碳纳米管的掺杂显著增加了聚甲苯胺蓝在电极表面的担载量,提高了检测灵敏度。在pH7.4的磷酸盐缓冲液中,杂化膜修饰电极对β-烟酰胺腺嘌呤二核苷酸(NADH)的氧化具有良好的催化作用,与裸电极相比氧化电位降低了560 mV,灵敏度明显提高。在8.7×10-8~1.3×10-4mol/L范围内,NADH的浓度与氧化电流呈线性关系,检出限为2.8×10-8mol/L,该修饰电极可用于NADH的测定。     

六氰合铁酸铜钴-多壁碳纳米管修饰电极研究

采用电沉积方法制备六氰合铁酸铜钴-多壁碳纳米管复合修饰电极(CuCoHCF-MWCNTs/GCE).研究碳纳米管用量、电解液组成对该修饰电极性能的影响.结果表明,与单一的六氰合铁酸铜钴薄膜修饰电极相比,六氰合铁酸铜钴-多壁碳纳米管复合修饰电极具有更优良的电化学特性,以其催化氧化过氧化氢,峰电流与过氧化氢浓度在3.16×10-5～2.92×10-3mol·L-1范围内呈良好的线性关系,线性回归方程为ip(μA)=0.5529+1.1299C(×10-4mol·L-1),相关系数r=0.9966,检出限为1.75×10-5mol·L-1.     

塑料瓶中双酚A的电化学测定方法研究

制备了多壁碳纳米管修饰碳糊电极（MWCNTs／CPE）,用循环伏安法（CV）和差分脉冲伏安法（DPV）研究了环境激素双酚A在多壁碳纳米管修饰电极上的电化学行为。结果表明,多壁碳纳米管修饰碳糊电极对双酚A有明显的电催化作用,在pH7．0的磷酸盐缓冲溶液（PBS）中,双酚A在0．504V处有1个明显的氧化峰。实验考察了底液的pH值、扫描速度、富集时间等因素的影响。在优化的条件下,双酚A的示差脉冲峰电流与其浓度在5．0×10^7-2．0×10^-5范围内呈良好的线性关系（r=0．99545）,检出限为1．0×10^-7mol／L（S／N=3）。该法用于实际样品中双酚A含量的测定,回收率为104．4％,测定结果的相对标准偏差为3．9％（n=6）。     

Electrochemistry and Adsorptive Stripping Voltammetric Determination of Amoxicillin on a Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrode

The study of electrochemical behavior of amoxicillin (AMX), a β‐lactam antibiotic, is described on a multiwalled carbon nanotubes (MWCNTs) modified electrode by electrochemical impedance spectroscopy (EIS) and adsorptive stripping voltammetry for sensitive determination of AMX in pharmaceutical and human urine samples within a wide pH range from 2.0 to 10.0. Also, studies by Fe₂O₃ nanoparticles modified carbon paste electrode show that iron oxide impurities in the MWCNTs are not active sites for sensing of amoxicillin. Under optimized conditions, the oxidation peak has two linear dynamic ranges of 0.6–8.0 and 10.0–80.0 μM with a detection limit of 0.2 μM and a precision of <4%.     

Synthesis and electrochemical characterization of sol–gel-derived RuO2/carbon nanotube composites

Ruthenium oxide was coated on multiwalled carbon nanotubes (MWCNTs) to obtain nanocomposite electrode which has a good response to the pH. To synthesize this electrode, gold and cobalt were coated on a stainless steel 304 substrates, respectively, and then, vertically aligned carbon nanotubes were grown on the prepared substrates by chemical vapor deposition. Gold reduced activity of the stainless steel, while cobalt served as a catalyst for growth of the carbon nanotube. Ruthenium oxide was then coated on MWCNTs via sol–gel method. At last, different techniques were used to characterize the properties of synthesized electrode including scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, X-ray diffraction, and cyclic voltammetry. SEM results showed that the length of the carbon nanotubes varied with reaction time, and in this research, it was maintained around 9 μm with a diameter about 100 nm. Electrochemical analysis revealed that optimum sol concentration and heat treatment temperature to meet the best pH sensing response were 0.1 M RuCl₃ sol and 200 °C, respectively. Moreover, the obtained electrode represented a linear and near-Nernstian response (about ?63 mV/pH) throughout the whole pH range (2–12) of Britton–Robinson buffer solutions.     

The Electrocatalytic Properties of Arc‐MWCNTs and Associated ‘Carbon Onions’

For the first time we report on the electrochemical characteristics of nanometer sized polyhedral graphite onions dispersed amongst arc‐MWCNTs. These are formed during the electric arc discharge method of producing ultrapure MWCNTs (arc‐MWCNTs). The carbon onions are randomly dispersed amongst the arc‐MWCNTs which are produced with very little amorphous carbon deposits or other unwanted impurities and are formed as closed‐ended tubes. By comparison with commercially available open‐ended hollow‐tube multiwalled carbon nanotubes made using the chemical vapor deposition method (cvd‐MWCNTs), a glassy carbon electrode (GCE), an edge‐plane pyrolytic graphite electrode (eppg) and basal plane pyrolytic graphite (bppg) electrode, we can speculate that it is the edge‐plane‐like defect sites that are the electroactive sites responsible for the apparent ‘electrocatalysis’ seen with a wide range of analytes including: ferrocyanide, ruthenium hexaamine(III), nicotinamide adenosine dinucleotide (NADH), epinephrine, norepinephrine, cysteine, and glutathione. The arc‐MWCNTs themselves are produced as closed‐ended tubes with very few, if any, edge‐plane‐like defect sites evident in their HRTEM characterization. Therefore we speculate that it is the carbon onions dispersed amongst the arc‐MWCNTs which have incomplete graphite shells or a rolled‐up ‘Swiss‐roll’ structures that posses the edge‐plane‐like defect sites and are responsible for the observed voltammetric responses. Carbon onions are no more or no less ‘electrocatalytic’ than open‐ended MWCNTs which in turn are no more electrocatalytic than an eppg electrode. As the carbon onions are ubiquitous in MWCNTs formed using the arc‐discharge method the authors advise that caution should be taken before assigning any electrocatalytic behavior to the MWCNTs themselves as any observed electrocatalysis likely arises from the carbon onion impurities.     

血红蛋白在壳聚糖修饰碳纳米管上的电化学特性及对过氧化氢的电催化分析

用壳聚糖对多壁碳纳米管进行修饰,构建了一种用于固定血红蛋白的新型复合材料,并研究了血红蛋白在该碳纳米管上的电化学性质及其对过氧化氢的电催化活性.扫描电镜结果表明,壳聚糖修饰的多壁碳纳米管呈单一的纳米管状,并能均匀分散在玻碳电极表面.紫外光谱分析表明血红蛋白在该复合膜内能很好地保持其原有的二级结构.将该材料固定在玻碳电极上后,血红蛋白能成功地实现其直接电化学.根据峰电位差随着扫描的变化,计算得到血红蛋白在壳聚糖修饰的碳纳米管膜上的电荷转移系数为0.57,表观电子转移速率常数为7.02 s-1.同时,该电极对过氧化氢显示出良好的催化性能,电流响应信号与H2O2浓度在1.0×10-6 ～1.5×10-3 mol/L间呈线性关系,检出限为5.0×10-7 mol/L.修饰电极显示了良好的稳定性.     

Doping effects of manganese on the catalytic performance and structure of NiMgO catalysts for controllabe synthesis of multi-walled carbon nanotubes

Doping effects of manganese （Mn） on catalytic performance and structure evolution of NiMgO catalysts for synthesis of multi-walled carbon nanotubes （MWCNTs） from methane were investigated for the first time. Addition of Mn in NiMgO catalyst can greatly improve the MWCNTs yield. Mno.2NiMgO catalyst among the tested ones gives the highest MWCNTs yield as 2244%, which is two times higher than that of the catalyst without Mn. The structure evolution, reduction behaviors and surface chemical properties of MnNiMgO catalysts with various Mn contents were studied in detail. It was found that the stable solid solution of NiMgO2 formed in NiMgO catalyst was disturbed by the addition of Mn. Instead, another solid solution of MnMg608 is formed. More amount of Ni can be reduced and dispersed on the catalyst surface to be acted as active sites. Importantly, the changes of Ni content on the surface are correlated with the Ni particle size and the outer diameter of MWCNTs, suggesting the controllable synthesis of MWCNTs over MnNiMgO catalysts.     

Fabrication of ferrocene functionalised ionic liquid/carbon nanotube nanocomposite modified carbon-ceramic electrode: application to the determination of hydrazine

A novel ionic liquid, 1-(ferrocenyl butyl)-3-methylimidazolium tetrafluoroborate (Fc-IL), was synthesised. The nanocomposite of Fc-IL and multi-walled carbon nanotubes (MWCNTs) was constructed and used for surface modification of carbon-ceramic electrode. The modified electrode was applied to the determination of hydrazine. Operational parameters such as pH of the solution, ionic liquid volume and amount of carbon nanotubes, which affect the analytical performance of the modified electrode, were optimised. The linear range of the modified electrode toward hydrazine concentration was 0.96–106.10 μg L^–1 with a detection limit of 0.64 μg L^–1 (S/N = 3). The modified electrode displayed high repeatability, reproducibility, long-term life time and low response time (<3 s). The applicability of this method was further tested by analysing the hydrazine content in boiler-feed water samples containing different concentrations of hydrazine and the results were in good agreement with the spectrophotometry method.     

生物合成纳米金与MWCNTs/L-Cys复合修饰玻碳电极测定左旋多巴

利用荷叶萃取液生物合成纳米金,并与多壁碳纳米管/L-半胱氨酸复合成修饰电极材料,研究了左旋多巴在该修饰电极上的电化学行为.在0.2 mol/L乙酸-乙酸钠体系(pH=2.6)中,氧化峰电流与左旋多巴浓度在0.6~40μmol/L及60~120μmol/L范围内呈良好的线性关系,检出限达5.2×10-8mol/L.实验结果表明,生物合成纳米金复合多壁碳纳米管/L-半胱氨酸修饰电极具有良好的稳定性和高灵敏度,对实际样品测定的回收率在91.2%~102.5%之间.     

Wireless sensing determination of uranium(IV) based on its inhibitory effect on a catalytic precipitation reaction

The adsorption of Eu(III) on multiwalled carbon nanotubes (MWCNTs) as a function of pH, ionic strength and solid contents are studied by batch technique. The results indicate that the adsorption of Eu(III) on MWCNTs is strongly dependent on pH values, dependent on ionic strength at low pH values and independent of ionic strength at high pH values. Strong surface complexation and ion exchange contribute to the adsorption of Eu(III) on MWCNTs at low pH values, whereas surface complexation and surface precipitation are the main adsorption mechanism of Eu(III) on MWCNTs. The desorption of adsorbed Eu(III) from MWCNTs by adding HCl is also studied and the recycling use of MWCNTs in the removal of Eu(III) is investigated after the desorption of Eu(III) at low pH values. The results indicate that adsorbed Eu(III) can be easily desorbed from MWCNTs at low pH values, and MWCNTs can be repeatedly used to remove Eu(III) from aqueous solutions. MWCNTs are suitable material in the preconcentration and solidification of radionuclides from large volumes of aqueous solutions in nuclear waste management.