Organoclay sorption of benzene as a function of total organic carbon content

The sorption of benzene to bentonite, activated carbon, and two organo-clays synthesized with the quaternary ammonium organic cations hexadecyltrimethylammonium (HDTMA) and benzyltriethylammonium (BTEA) was quantified as a function of total organic carbon content. The unmodified bentonite sorbed no benzene, while the activated carbon exhibited the strongest benzene uptake. For the organoclays, organic cations were exchanged onto Wyoming bentonite at four different percentages of the clay's cation exchange capacity. For HDTMA clay, in which partitioning is the dominant sorptive medium, it was determined that benzene sorption increased as the total organic carbon content increased (as the clay became more hydrophobic). In contrast, the sorption of benzene to BTEA clay, an adsorptive clay, decreased as the total organic carbon content of the clay was increased. It is believed that the sorptive capacity of BTEA clay decreases due to the formation of positively charged dimers on the clay's surface that block access to the sorptive sites. The organoclays sorbed more benzene than the unmodified bentonite, but less than the activated carbon.     

Rapid voltammetric determination of nitroaromatic explosives at electrochemically activated carbon-fibre electrodes

The electrochemical behaviour of some nitroaromatic explosives (2,4,6-trinitrotoluene, TNT; 2,6-dinitrotoluene, 2,6-DNT; 2-nitrotoluene, 2-NT; 2-amino-4,6-dinitrotoluene, 2-A-4,6-DNT; 3,5-dinitroaniline, 3,5-DNA; and nitrobenzene, NB) at electrochemically activated carbon-fibre microelectrodes is reported. Electrochemical activation of such electrode material by repeated square-wave (SW) voltammetric scans between 0.0 and +2.6 V versus Ag/AgCl, produced a dramatic increase in the cathodic response from these compounds. This is attributed to the increase of the carbon-fibre surface area, because of its fracture, and the appearance of deep fissures along the main fibre axis into which the nitroaromatic compounds penetrate. Based on the important contribution of adsorption and/or thin layer electrolysis to the total voltammetric response, a SW voltammetric method for rapid detection of nitroaromatic explosives was developed. No interference was found from compounds such as hydrazine, phenolic compounds, carbamates, triazines or surfactants. The limits of detection obtained are approximately 0.03 g mL^–1 for all the nitroaromatic compounds tested. The method was applied for the determination of TNT in water and soil spiked samples; recoveries were higher than 95% in all cases.     

Liquid chromatographic separation of 2,4,6-trinitrotoluene and its principal reduction products

A liquid chromatographic method is described for the baseline separation of 2,4,6-trinitrotoluene (TNT) and its main reduction products. Two analytical columns (LC-18 and LC-CN) are connected in series and eluted isocratically at 1.5 ml min^?1 with water-methanol-tetrahydrofuran (60.5 + 25 + 14.5). The capacity factors (k′) are 1.4, 1.6, 5.1, 6.4 and 7.0 for 2,6-diamino-4-nitroluene, 2,4-diamino-6-nitrotoluene, TNT, 4-amino-2,6-dinitrotoluene and 2-amino-4,6-dinitrotoluene, respectively.     

The determination of nitroaromatics and nitramines in ground and drinking water by wide-bore capillary gas chromatography

A method has been developed to determine the concentration of nitroaromatics and nitramines in drinking water at levels below those previously achieved by gas chromatography. The nitroaromatics and nitramines are extracted from water using toluene and isoamyl acetate, respectively. The extracts are analyzed via a gas chromatograph equipped with a DB-1301 widebore fused-silica capillary column and an electron capture detector. Method detection limits of 0.003 micrograms/L for 2,6-dinitrotoluene (2,6-DNT), 0.04 micrograms/L for 2,4-dinitrotoluene (2,4-DNT), 0.06 micrograms/L for 2,4,6-trinitrotoluene (TNT), 0.3 micrograms/L for cyclotrimethylenetrinitramine (RDX), and 6.0 micrograms/L for cyclotetramethylenetetranitramine (HMX) have been obtained using this method.     

一种新的分离三硝基甲苯及其代谢产物的高效液相色谱方法

An HPLC method is described for separation of TNT and its main reduction metabolites. Two columns(LC-C(18) and LC-CN)are connected in series and operated isocratically at 1.0mL/min with water-methanol-tetrahydrofuran(60+ 35+ 5 ). The baseline separation of 4-amino-2,6-dinitrotoluene(4A) and 2-amino-4,6-dinitrotoluene(2A) ,which are main metabolites of TNT,is obtained(Rs=2.1).     

Delamination behavior of silicate layers by adsorption of cationic surfactants

Smectite that has reacted for 48 h with hexadecyltrimethylammonium (HDTMA) cations equivalent to 0.01-3.0 times the cation exchange capacity (CEC) converts to HDTMA-smectite. The microstructure of this organoclay is observed using X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM). When Na cations in the interlayer of clay are exchanged with HDTMA ions, the changes in internal and external surface configuration are augmented by the intercalation of organic surfactants, showing a heterogeneous increase of interlayer spacings. As HDTMA loading increases, the chance of delaminated layers being developed increases locally in the low-charge interlayer regions by the sufficient adsorption of organic surfactants beyond the CEC due to the tendency of alkyl chain interaction.     

Use of reversed-phase high-performance liquid chromatography-diode array detection for complete separation of 2,4,6-trinitrotoluene metabolites and EPA Method 8330 explosives: influence of temperature and an ion-pair reagent

Explosives such as 2,4,6-trinitrotoluene (TNT), octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) are widely distributed environmental contaminants. Complete chromatographic separation is necessary in order to accurately determine and quantify explosives and their degradation products in environmental samples and in (bio)transformation studies. The present study describes a RP-HPLC method with diode array detection using a LC-8 guard column, a Supelcosil LC-8 chromatographic column, and a gradient elution system. This gradient method is capable of baseline separating the most commonly observed explosives and TNT transformation metabolites including 2,4,6-triaminotoluene (TAT) in a single run. The TNT metabolites separated were 2-hydroxylamino-4,6-dinitrotoluene, 4-hydroxylamino-2,6-dinitrotoluene, 2,4-dihydroxylamino-6-nitrotoluene, 4,4',6,6'-tetranitro-2,2'-azoxytoluene, 2,2',6,6'-tetranitro-4,4'-azoxytoluene, 4,4',6,6'-tetranitro-2,2'-azotoluene, 2,2',6,6'-tetranitro-4,4'-azotoluene, 2-amino-4,6-dinitrotoluene, 4-amino-2, 6-dinitrotoluene, 2,6-diamino-4-nitrotoluene, 2,4-diamino-6-nitrotoluene, and TAT. The same gradient method at a different column temperature can also be used to baseline separate the explosives targeted in the Environmental Protection Agency (EPA) Method 8330 with approximately 22% reduction in total run time and 48% decrease in solvent consumption compared to previously published methods. Good separation was also obtained when all TNT metabolites and EPA Method 8330 compounds (a total of 23 compounds) were analyzed together; only 2,6-DANT and HMX co-eluted in this case. The influence of temperature (35-55 degrees C) and the use of an ion-pair reagent on the chromatographic resolution and retention were investigated. Temperature was identified as the key parameter for optimal baseline separation. Increased temperature resulted in shorter retention times and better peak resolution especially for the aminoaromatics investigated. The use of an ion-pair reagent (octanesulfonic acid) generally resulted in longer retention times for compounds containing amine functional groups, more baseline noise, and decreased peak resolution.     

Determination of nitroaromatic, nitramine, and nitrate ester explosives in soil by gas chromatography and an electron capture detector

Hazardous waste site characterization, forensic investigations, and land mine detection are scenarios where soils may be collected and analyzed for traces of nitroaromatic, nitramine, and nitrate ester explosives. These thermally labile analytes are traditionally determined by high-performance liquid chromatography (HPLC); however, commercially available deactivated injection port liners and wide-bore capillary columns have made routine analysis by gas chromatography (GC) possible. The electron-withdrawing nitro group common to each of these explosives makes the electron capture detector (ECD) suitable for determination of low concentrations of explosives in soil, water, and air. GC-ECD and HPLC-UV concentration estimates of explosives residues in field-contaminated soils from hazardous waste sites were compared, and correlation (r>0.97) was excellent between the two methods of analysis for each of the compounds most frequently detected: 2,4,6-trinitrotoluene (TNT), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 2,4-dinitrotoluene (2,4-DNT), 1,3-dinitrobenzene (1,3-DNB), 1,3,5-trinitrobenzene (TNB), and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX). The analytes were extracted from soils with acetonitrile by 18 h of sonication in a cooled ultrasonic bath. Two soil-to-solvent ratios were evaluated: 2.00 g:10.00 ml and 25.0 g:50.0 ml. GC-ECD method detection limits were similar for the two soil-to-solvent ratios and were about 1 mug kg(-1) for the di- and trinitroaromatics, about 10 mug kg(-1) for the mono-nitroaromatics, 3 mug kg(-1) for RDX, 25 mug kg(-1) for HMX, and between 10 and 40 mug kg(-1) for the nitrate esters (nitroglycerine [NG] and pentaerythritol tetranitrate [PETN]). Spike recovery studies revealed artifacts introduced by the spiking procedure. Recoveries were low in some soils if the amount of soil spiked was large (25.0 g) compared to the volume of spike solution added (1.00 ml). Recoveries were close to 100% when 2.00-g soil samples were spiked with 1.00 ml of solution. Analytes most frequently found in soils collected near buried land mines were the microbial transformation products of TNT (2-amino-4,6-dinitrotoluene [2-Am-DNT] and 4-amino-2,6-dinitrotoluene [4-Am-DNT]), manufacturing impurities of TNT (2,4-DNT, 2,6-DNT, and 1,3-DNB), and TNT. The microbial reduction products of the isomers of DNT and of 1,3-DNB were also detected, but the ECD response to these compounds is poor.     

Sorption interactions of volatile organic compounds with organoclays under different humidities by using linear solvation energy relationships

Organoclays are usually used as sorbents to reduce the spread of organic compounds and to remove them at contaminated sites. The sorption equilibrium and the mechanisms of volatile organic compounds (VOCs) on organoclays under different humidities are helpful for developing efficient organoclays and for predicting the fate of VOCs in the environment. In this study, the organoclay was synthesized through exchanging inorganic cations by hexadecyltrimethyl ammonium (HDTMA) into montmorillonite, resulting in 12?% of organic content. The surface area of organoclay was smaller than the unmodified clay due to the incorporation of organic cations into the interlayer. Both adsorption on organoclay surface and partition into the incorporated HDTMA in organoclay played roles on the sorption process. Compared the sorption coefficients in montmorillonite and different modified clays, the incorporated organic cations overcame the inhibition effect of hydrophilic surface of clay on the sorption process of hydrophobic organic compounds from water. The sorption coefficients of VOC vapors on organoclay were further characterized using a linear solvation energy relationship (LSER). The fitted LSER equations were obtained by a multiple regression of the sorption coefficients of 22 probe chemicals against their solvation parameters. The coefficients of the five-parameter LSER equations showed that high HDTMA-content montmorillonite interacts with VOC molecules mainly through dispersion, partly through dipolarity/polarizability and hydrogen-bonds as well as with negative π-/n-electron pair interaction. The interaction analysis by LSERs suggests that the potential predominant factors governing the sorption of VOCs are dispersion interactions under all tested humidity conditions, similar with the lower level modified clay. The derived LSER equations successfully fit the sorption coefficients of VOCs on organoclay under different humidity conditions. It is helpful to design better toxic vapor removal strategy and evaluate the fate of organic contaminants in the environment.     

Very fast sorbent for organic dyes and pollutants

The increasing use of organic compounds endangering the environment encourages search for more efficient sorbents. While crude clay minerals are effective for the adsorption of cations, modified organoclays may adsorb negative and hydrophobic molecules. In this short communication, we present a very fast adsorbing organoclay based on montmorillonite with crystal violet pre-adsorbed up to neutralization of the negative charges. Sorption of erythrosin-B and 2,4,5-trichlorophenol to such organoclay reaches equilibrium in less than a minute, whereas with activated carbon, it took tens of minutes. The pseudo second-order kinetic coefficient for the process was at least two orders of magnitude smaller for the organoclay. Because sorption kinetics is an important factor in water purification, such fast sorbent might have broad environmental applications.     

Influence concentration of modifying agent on properties of natural rubber/organoclay nanocomposites

Sodium-montmorillonite (Na-MMT) nanoclay was modified with different concentrations of octadecylamine organic modifying agent at 0.5, 1.0 and 1.5 times the CEC of Na-MMT. Influence of concentration of modifying agent on properties of the organoclays and natural rubber/organoclay nanocomposites was investigated. It was found that the optimum concentration of modifying agent was 1.5 times the CEC of Na-MMT. That is, at this concentration, larger d-spacing of organoclay particles and higher degree of clay dispersion in natural rubber matrix were observed. Larger interlayer d-spacing also caused enhancement of the mechanical properties of the NR/organoclay nanocomposites. Additionally, the NR/organoclay nanocomposites with higher concentration of modifying agent exhibited faster curing reaction with higher crosslink density. Furthermore, the organoclays with larger d-spacing and higher degree of dispersion in the natural rubber matrix exhibited enhancement of the mechanical and dynamic properties and thermal stability of natural rubber/organoclay nanocomposites.     

活性炭纤维固相微萃取-气相色谱法测定海水中的硝基苯类和环酮类化合物

建立了自制活性炭纤维固相微萃取与气相色谱联用测定海水中6种硝基苯类和环酮类化合物的分析方法。优化的萃取条件为: 样品中加NaCl至饱和,在1500 r/min速率搅拌下,于60 ℃水浴中顶空萃取30 min,于280 ℃下解吸2 min。方法的线性范围为0.01～400 μg/L,检出限为1.4～3.2 ng/L,相对标准偏差(RSD,n6)为1.4%～7.8%。海水样品中硝基苯类和环酮类化合物的加标回收率和RSD分别为86.3%～101.8%和3.7%～7.8%。应用所建立的方法对东海近岸表层水样进行测定,其中硝基苯、1,3-二硝基苯、2,6-二硝基甲苯的质量浓度分别为0.756,0.944,0.890 μg/L。实验结果表明,该方法简便、高效、无需有机溶剂,适合于海洋水体中硝基苯类和环酮类化合物的分析。     

Thermal analyis of hexadecyltrimethylammonium–montmorillonites

Na-montmorillonite (Na-MONT) was loaded with hexadecyltrimethylammonium cations (HDTMA) by replacing 41 and 90% of the exchangeable Na with HDTMA, labeled OC-41 and OC-90, respectively. Na-MONT, OC-41, and OC-90 were heated in air up to 900 °C. Unheated and thermally treated organoclays heated at 150, 250, 360, and 420 °C are used in our laboratory as sorbents of different hazardous organic compounds from waste water. In order to get a better knowledge about the composition and nature of the thermally treated organoclays Na-MONT and the two organo-clays were studied by thermogravimetry (TG) in air and under nitrogen. Carbon and hydrogen contents in each of the thermal treated sample were determined and their infrared spectra were recorded. The present results showed that at 150 °C both organoclays lost water but not intercalated HDTMA cations. At 250 °C, many HDTMA cations persisted in OC-41, but in OC-90 significant part of the cations were air-oxidized into H₂O and CO₂ and the residual carbon formed charcoal. After heating both samples at 360 °C charcoal was present in both organo clays. This charcoal persisted at 420 °C but was gradually oxidized by air with further rise in temperature. TG runs under nitrogen showed stepwise degradation corresponding to interlayer water desorption followed by decomposition of the organic compound, volatilization of small fragments and condensation of non-volatile fragments into quasi-charcoal. After dehydroxylation of the clay the last stages of organic matter pyrolysis and volatilization occurred.     

Change in regioselectivity in the monoreduction of 2,4,6-trinitrotoluene with titanium(III) and vanadium(II) ions in the presence of iron(II) and copper(II) salts

Small additives of iron(II) or copper(II) salts change the regioselectivity of 2,4,6-trinitrotoluene monoreduction with titanium(III) chloride affording predominantly less accessible 2-amino-4,6-dinitrotoluene over 4-amino-2,6-dinitrotoluene (from 25% when the reduction occurs in the absence of the iron and copper salts to 70% in the presence of these salts). A possible mechanism of the process is discussed. Dedicated to Academician N. K. Kochetkov on the occasion of his 90th birthday. __________ Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 1172–1176, May, 2005.     

Detection of organic gunshot residues from human hands using direct sample analysis-time of flight-mass spectrometry

The organic gunshot residues (OGSRs), specifically methyl centralite (MC; 1,3-dimethyl-1,3-diphenylurea), ethyl centralite (EC; 1,3-diethyl-1,3-diphenylurea), 2,4-DNT (2,4-dinitrotoluene), and TNT (trinitrotoluene), are characteristic compounds for which forensic analysts test determining if a person has discharged a firearm. A set of 200 samples from 50 shooters were collected as part of the validation study. Pistol 9 mm and special revolver .38 were fired at indoor and outdoor shooting ranges. The development of a methodology based on direct analysis of samples-time of flight-mass spectrometry (DSA-TOF-MS) made it possible to identify the main components of organic shot residues, which gave the possibility to introduce a new method of analysis of shot residues in the Chilean supply area. The DSA-TOF-MS provided extensive information on the composition of the shot residues: MC, EC, 2,4-DNT, and TNT. Samples taken from the trigger hands required minimal sample preparation that reduced analyses time. With the implementation of new alternative analytical methodologies, a great step would be taken in the analysis of OGSRs, because now there is no such technique for its analysis in Chile, and the results would also complement the existing inorganic elemental analyses generated during a gunshot.     

One-step isolation and identification of hydroxylamino-dinitrotoluenes, unstable products from 2,4,6-trinitrotoluene metabolites, with thin-layer chromatography and laser time-of-flight mass spectrometry

Two kinds of hydroxylamino-dinitrotoluenes (HADNTs), 2-hydroxylamino-4,6-dinitrotoluene (2HADNT) and 4-hydroxylamino-2,6-dinitrotoluene (4HADNT), are known to be major metabolites produced from 2,4,6-trinitrotoluene (TNT) by bacteria. These chemicals could not be identified as TNT metabolites produced by Pseudomonas sp. strain TM15 because the mass spectra of these chemicals could not be obtained by liquid chromatography-mass spectrometry (MS) or gas chromatography-MS, which are the classic methods for identifying the metabolites of xenobiotics. However, these problems are overcome by isolating 2HADNT and 4HADNT from TNT metabolites with one-step thin-layer chromatography using dichloromethane as the developing solvent, and individually extracting them into acetonitrile by collecting spots of 2HADNT and 4HADNT. The purity of each HADNT was approximately 98%, based on the results of high-performance liquid chromatographic analyses. 2HADNT and 4HADNT are identified by obtaining their mass spectra with laser time-of-flight MS. 2HADNT and 4HADNT dissolve in distilled water and are spontaneously broken down with time. Also, heat treatment (increasing temperatures) and dissolved oxygen accelerate the destruction of HADNTs. This technique may be applicable for the identification and exact quantitative analysis of unstable and fragile compounds such as HADNTs.     

Simultaneous determination of organic and cationic species in explosives residues with column-switching liquid chromatography-ion chromatography system

A new column-switching method has been proposed for the determination of 14 organic explosives (1,3,5,7-tetranitro-N-methylaniline, 1,3,5-trinitro-1,3,5-triazacyclohexane, 1,3,5-trinitrobenzene, 1,3-dinitrobenzene, nitrobenzene, 2,4,6-N-tetranitro-N-methylaniline, Trinitrotoluene, 4-amino-2,6-dinitrotoluene, 2-amino-4,6-dinitrotoluene, 2,6-dinitrotoluene, 2,4-dinitrotoluene, 2-nitrotoluene, 4-nitrotoluene, and 3-nitrotoluene) and/or five inorganic cations (Na(+), NH(4)(+), K(+), Mg(2+), and Ca(2+)) using liquid chromatography linked to ion chromatography by a switching valve. The mobile phase was methanol-water (40/60, v/v) for a C18 reversed-phase column and 3 mM of methanesulfonic acid (pH 2.5) for a cation-exchange column, respectively. Under the optimal conditions, the 14 organic explosives and the five inorganic cations were separated and detected simultaneously within 45 min. The limits of detection (S/N = 3) of the 14 organic explosives and the five inorganic cations were in the range of 0.0048-0.0333 mg/L and 0.0116-0.1851 mg/L, respectively. The linear correlation coefficients were 0.9971-0.9999, and the relative standard deviation of the retention time and the peak area were 0.02-0.31% and 0.51-3.64%, respectively. The method was successfully applied to the determination of organic explosives and inorganic cations in dust samples.     

Analysis of explosives using electrospray ionization/ion mobility spectrometry (ESI/IMS)

The analysis of explosives with ion mobility spectrometry (IMS) directly from aqueous solutions was shown for the first time using an electrospray ionization technique. The IMS was operated in the negative mode at 250°C and coupled with a quadrupole mass spectrometer to identify the observed IMS peaks. The IMS response characteristics of trinitrotoluene (TNT), 2,4-dinitrotoluene (2,4-DNT), 2-amino-4,6-dinitrotoluene (2-ADNT), 4-nitrotoluene (4-NT), trinitrobenzene (TNB), cyclo-1,3,5-trimethylene-2,4,6-trinitramine (RDX), cyclo-tetramethylene-tetranitramine (HMX), dinitro-ethyleneglycol (EGDN) and nitroglycerine (NG) were investigated. Several breakdown products, predominantly NO₂⁻ and NO₃⁻, were observed in the low-mass region. Nevertheless, all compounds with the exception of NG produced at least one ion related to the intact molecule and could therefore be selectively detected. For RDX and HMX the [M+Cl⁻]⁻ cluster ion was the main peak and the signal intensities could be greatly enhanced by the addition of small amounts of sodium chloride to the sprayed solutions. The reduced mobility constants (K₀) were in good agreement with literature data obtained from experiments where the explosives were introduced into the IMS from the vapor phase. The detection limits were in the range of 15–190 μg l⁻¹ and all calibration curves showed good linearity. A mixture of TNT, RDX and HMX was used to demonstrate the high separation potential of the IMS system. Baseline separation of the three compounds was attained within a total analysis time of 6.4 s.     

Mild pre-heating of organic cation-exchanged clays enhances their interactions with nitrobenzene in aqueous environment

Aqueous sorption kinetics and equilibrium isotherms of nitrobenzene were studied on two series of sorbents that were prepared by (i) replacing inorganic exchangeable cations in Wyoming bentonite with tetraethylammonium (TEA) and benzyltrimethylammonium (BTMA) and (ii) heating synthesized complexes in air at different temperatures (between 150 and 420°C). The aim of this work was to examine recently observed enhancement of aqueous sorption of a probe organic sorbate on organoclays after mild thermal pre-treatment of sorbents. Thermal pre-treatment of TEA- and BTMA-clays at 150°C results in the maximal enhancement of nitrobenzene–sorbent interactions as compared with treatment of original bentonite and its exchange complexes formed with long-chain quaternary ammonium (n-hexadecyltrimethylammonium, HDTMA). Based on C, N content data and FTIR spectra of TEA- and BTMA-clay complexes, no indications of decomposition of organic matter were found in organoclays heated at 250°C (and below this temperature). Suppressed hydration of pre-heated sorbents resulting in a lessening of water–organic sorbate competition for sorption sites is considered to be responsible for thermally induced enhancement of nitrobenzene–sorbent interactions. In the HDTMA-based organoclays, the long-chain aliphatic groups of the quaternary ammonium can additionally interact with clay surface thus competing with organic sorbate–sorbent surface interactions and, in this way, mitigating the enhancement of nitrobenzene sorption on thermally treated sorbents.     

Simultaneous sorption of benzene and heavy metals onto two organoclays

An experimental study was performed to determine the feasibility of using hexadecyltrimethylammonium bentonite clay (HDTMA-clay) and benzyltriethylammonium bentonite clay (BTEA-clay) for simultaneous sorption of benzene and one of four heavy metals (Pb, Cd, Zn and Hg). Specifically, the role of competition between benzene and each heavy metal was studied. The sorption of Pb, Cd, and Zn on both BTEA- and HDTMA-clay decreases in the presence of benzene relative to the sorption obtained without benzene present. This indicates that there is competition between Pb, Cd, and Zn and organic compounds during sorption onto both organoclays. On BTEA-clay, Cd, Pb and Zn sorption was reduced by 24, 37, and 51%, respectively. On HDTMA-clay, Cd, Pb, and Zn sorption was reduced by 25, 30, and 57%, respectively. Hg sorption was not affected either by the presence of benzene or by the organoclays used. The sorption of benzene onto BTEA-clay in the presence of Hg, Zn, Pb, and Cd was less than the sorption observed when no heavy metal was present. The presence of Hg resulted in the most significant decrease in sorption, causing a 59% reduction in benzene sorption. The presence of Zn, Pb, and Cd caused a 41, 35, and 31% reduction in benzene sorption, respectively. In general, sorption of benzene onto HDTMA-clay was not affected by the presence of the heavy metals, indicating there are no competitive effects observed with Zn, Cd, and Hg when HDTMA-clay was the sorbent. However, the presence of Pb did cause a 20% reduction in benzene sorption to HDTMA-clay. Both organoclays tested had dual sorptive properties for both heavy metals and an organic contaminant. While the competitive effects were greater for the BTEA clay, both organoclays are capable of simultaneously removing benzene and either Zn, Cd, Hg, or Pb from aqueous solution.