Synthesis of Mg2Al-Cl layered double hydroxide nanosheets in a surfactant-free reverse microemulsion

The synthesis of Mg₂Al-Cl layered double hydroxide (LDH) nanosheets in a surfactant-free reverse microemulsion is described. The microemulsion was composed of toluene, isopropanol, and an aqueous solution as the dispersed phase. An aqueous LDH nanosheet dispersion was obtained by a double-microemulsion technique. LDH nanosheets were characterized by X-ray powder diffraction, transmission electron microscopy, scanning electron microscopy, atomic force microscopy, Fourier transform infrared spectroscopy, and thermogravimetric and elemental analyses. The LDH nanosheets consisted of a single brucite layer without any loading of organic molecules. To the best of our knowledge, this is the first report of a naked LDH monolayer aqueous dispersion being directly obtained. The LDH monolayers can be used as building blocks for LDH-based functional materials.     

Variation of surface properties and textural features of spinel ZnAl2O4 and perovskite LaMnO3 nanoparticles prepared via CTAB-butanol-octane-nitrate salt microemulsions in the reverse and bicontinuous states

Two binary oxides, a spinel, ZnAl2O4, and a typical perovskite, LaMnO3, have been prepared via CTAB-1-butanol-n-octane-nitrate salt microemulsion in the reverse and bicontinuous states. The exact point of the reverse and bicontinuous states of the microemulsion used in the synthesis was determined by conductivity experiments. The materials obtained after heating at 800 degrees C were characterized by XRD analysis for their crystal structure, N2 porosimetry for their surface area and porosity, and SEM and TEM photography for their texture. The ZnAl2O4 spinel obtained via the reverse microemulsion appears in SEM in a more fragmented form and with a higher specific surface area (143.7 m(2)g(-1)), compared to the corresponding solid prepared via the bicontinuous microemulsion, which appears more robust with lower surface area (126.7 m(2)g(-1)). Nevertheless both materials reveal in TEM a sponge-like structure. The perovskite materials LaMnO3 prepared via the reverse microemulsion showed in SEM a peculiar doughnut-like texture, each doughnut-like secondary particle having a diameter of 2 microm. The corresponding sample developed via the bicontinuous microemulsion showed in SEM uniform secondary particles of size approximately 0.2 microm. Both perovskite samples LaMnO3 appear well crystallized with relative low surface areas, 23.7 m(2)g(-1) for the reverse sample and 10.9 m(2)g(-1) for the bicontinuous one. The TEM photographs reveal that both of them, of reversed and bicontinuous origin, are made up of primary nanoparticles in the size range 40-100 nm. In SEM those materials showed a different secondary structure.     

Poly(ethyleneimine) as reducing and stabilizing agent for the formation of gold nanoparticles in w/o microemulsions

This paper is focused on the use of branched poly(ethyleneimine) (PEI) as reducing as well as stabilizing agent for the formation of gold nanoparticles in different media. The process of nanoparticle formation was investigated, in the absence of any other reducing agents, in microemulsion template phase in comparison to the nucleation process in aqueous polymer solution.

On the one hand, it was shown that the polyelectrolyte can be used for the controlled single-step synthesis and stabilization of gold nanoparticles via a nucleation reaction and particles with an average diameter of 7.1 nm can be produced.

On the other hand, it was demonstrated that the polymer can also act as reducing and stabilizing agent in much more complex systems, i.e. in water-in-oil (w/o) microemulsion droplets. The reverse microemulsion droplets of the quaternary system sodium dodecylsulfate (SDS)/toluene–pentanol (1:1)/water were successfully used for the synthesis of gold nanoparticles. The polymer, incorporated in the droplets, exhibits reducing properties, adsorbs on the surface of the nanoparticles and prevents their aggregation. Consequently, nanoparticles of 8.6 nm can be redispersed after solvent evaporation without a change of their size.

Nevertheless, the polymer acts already as a “template” during the formation of the nanoparticles in water and in microemulsion, so that an additional template effect of the microemulsion is not observed.

The particle formation for both methods is checked by means of UV–vis spectroscopy and the particle size and size distribution are investigated via dynamic light scattering and transmission electron microscopy (TEM).     

One-pot synthesis of hybrid multifunctional silica nanoparticles with tunable coating by click chemistry in reverse w/o microemulsion

Multifunctional hybrid silica nanoparticles with a fluorescent core and tunable organic or polymeric shell can easily be prepared by a sol-gel process followed by 1,3 dipolar cycloaddition (CuAAC) in the same reverse quaternary W/O microemulsion. Compared to a classical multistep process, this one-pot synthesis reduces greatly the number of purification steps and avoids aggregation phenomena. The confinement of reactants inside the micellar system gives rise to a noticeable increase of the CuAAC reaction rate. In addition, using simultaneously two different substrates for CuAAC on silica allows us to obtain directly multifunctional hybrid nanoparticles displaying a double grafting without any separation or purification steps except the final recovery by centrifugation, which opens the door to a tunable coating of the nanoparticles. Particularly, the hydrophilic-lipophilic balance of the coating can be adjusted by implementing the pertinent MPEG:dodecyl azide ratio. As an application, the great versatility of this strategy has been proved by the one-pot synthesis of fluorescent silica nanoparticles with a PEG coating and encapsulating silver clusters.     

反相微乳液法制备纳米SiO2的研究

在壬基酚聚氧乙烯5醚(NP-5)/环己烷/氨水的反相微乳液体系中，进行正硅酸乙酯(TEOS)的水解、缩合反应，得到粒径在30～50 nm的单分散纳米SiO₂胶体。红外光谱法(FTIR)及透射电子显微镜(TEM)观察证明了纳米SiO₂粒子的生成。反相微乳液体系相图的研究表明，水相为氨水比纯水有较窄的W/O型微乳区。氨水微乳液是碱催化TEOS水解、缩合制备纳米SiO₂粒子的适宜体系。当体系中TEOS的浓度增大时，粒子的粒径随之增大。降低NP-5     

Synthesis of Ag2S quantum dots in water-in-CO2 microemulsions

Ag2S nanocrystals with a mean diameter of 5.9 nm (sigma= 1.65 nm) and characteristic surface plasmon resonance absorption at 330 nm have been synthesized in water-in-supercritical CO2 reverse microemulsion using the commonly used AOT surfactant with 2,2,3,3,4,4,5,5-octafluoro-1-pentanol (F-pentanol) as cosurfactant.     

Synthesis of Ag and AgI quantum dots in AOT-stabilized water-in-CO2 microemulsions

Silver and silver iodide nanocrystals have been synthesized in the water-in-CO(2) reverse microemulsions formed by the commonly used surfactant, sodium bis(2-ethylhexyl)sulfosuccinate (AOT), in the presence of 2,2,3,3,4,4,5,5-octafluoro-1-pentanol as cosurfactant. The nanometer-sized aqueous domains in the microemulsion cores not only act as nanoreactors, but the surfactant interfacial monolayer also helps the stabilization of the metal and semiconductor nanoparticles. The transmission electron microscopy results show that silver and silver iodide nanocrystals with average diameters of 6.0 nm (standard deviation, SD=1.3 nm) and 5.7 nm (SD=1.4 nm), respectively, were formed. The results indicate that the method can be utilized as a general and economically viable approach for the synthesis of metal and semiconductor quantum dots in environmentally benign supercritical carbon dioxide.     

Application of tetrahydrofuran dispersant in microemulsion for fabricating titania mesoporous thin film

A new strategy was used to fabricate titania mesoporous thin film by incorporating tetrahydrofuran (THF) into the CTAB/n-butyl alcohol/cyclohexane/water reverse microemulsion as a micelle disperser. Highly dispersed and congregated TiO(2) particles in the microemulsion with and without THF were observed by transmission electron microscopy (TEM), respectively. The photographs observed by field-emission scanning electron microscopy (FE-SEM) show that a uniform titania mesoporous thin film with monodisperse TiO(2) spherical nanoparticles of ca. 20 nm was obtained using the microemulsion with THF.     

在水/环己烷微乳体系中制备纳米级氧化锆微粒

研究了在水 环己烷 正己醇 Triton X 100的微乳体系中, 几种主要实验参数对由氯氧化锆制备氧化锆纳米粒子的比表面积及其颗粒大小的影响.实验结果表明，微乳体系中水与表面活性剂的摩尔比ro、氯氧化锆的浓度以及微乳沉淀反应的温度都对氧化锆的比表面积有很大影响.在不同温度的微乳体系，氯氧化锆浓度对最终氧化锆粒子的比表面积的影响不同.通过优化制备条件，制得了比表面积为212 m2•g－1（450 ℃焙烧后）的氧化锆纳米粉体.文中还对所制备的氧化锆样品进行了X射线衍射(XRD)、透射电镜（TEM）和氮气吸附的分析.     

反相微乳液法制备膜状普鲁士蓝类配合物纳米材料

在十六烷基三甲基溴化铵(CTAB)/正戊醇/异辛烷/水构成的油包水型(W/O)微乳体系中合成了膜状及50 nm立方状的Co-Fe普鲁士蓝类配合物(cobalt-iron Prussian blue analogues). 研究了w值(水与CTAB的物质的量的比)、反应物浓度和反应温度对产品形貌的影响. 并用原子力显微镜(AFM), 透射电子显微镜(TEM), 电子能谱(EDS), X射线光电子能谱(XPS)和红外(IR)对产品进行了表征.     

反相微乳液法合成钛酸钡纳米棒

本文在W/O型反相微乳液(Reverse Microemulsion)体系中制得了BaTiO3纳米棒, 考察了ωo值、反应物浓度等因素对BaTiO3纳米棒尺寸及形貌的影响. 用TEM、XRD和电子衍射对材料进行了表征,并用ICP测试了产品中钡与钛的摩尔比.     

An investigation into the relationship between the electrical conductivity and particle size of polyaniline in nano scale

Polyaniline nanoparticle (nPANI) was successfully synthesized through ultrasonic-assisted reverse microemulsion polymerization method. The effect of four parameters including concentration of aniline (ANI) as monomer, molar ratio of dodecybenzene sulfonic acid (DBSA) as surfactant to ANI, molar ratio of ammonium peroxydisulfate (APS) as oxidant to ANI and polymerization temperaturewere systematically studied in terms of the structural characterizations of nPANI by applying the Taguchi method of experimental design. Data analysis indicated that there is a dependency between conductivity and particle size in the nanoscale; the maximum conductivity of nPANI was obtained when the diameter of the particles was 30?nm.     

反相微乳液模板法合成介孔聚苯乙烯

提出并实施了反相微乳液为模板合成介孔聚合物的新方法. 通过考察氯仿/CTAB/水三元系反相微乳液的稳定性, 以及均相微乳液粒径变化规律, 得到了三元反相微乳液体系的稳定区域. 以(NH4)2S2O8为引发剂, 利用此反相微乳液为模板合成得到介孔聚苯乙烯材料. 产物的XRD图谱中有两个明显的衍射峰, 对应的晶面间距离d分别为2.6和1.3 nm, 1/d值之比等于1:2, 为层状结构. N2气吸附/脱附曲线表明大部分孔径为1.7 nm, 与动态光散射测得的微乳液液滴的尺寸相一致.     

Growth kinetics of CdSe nanoparticles synthesized in reverse micelles using bis(trimethylsilyl) selenium precursor

We first focus on the kinetics of nanoparticle growth in a microemulsion synthesis of CdSe semiconductor nanocrystals. The process consists of a fast initial stage of typical time constant of the order of 10³ s followed by a slow stage of time constant of the order of 10⁴s. Growth proceeds similarly to that described for the hot-matrix synthesis of CdSe, underlining the generality of the two-stage growth mechanism, irrespective of the matrix type and synthesis conditions. However, the time constant of each stage in the microemulsion synthesis is much larger than in the hot-matrix one. Also, the ratio between the fast and slow time constant is appreciably bigger. We also prove that larger size reverse micelles, obtained by increasing the water:surfactant ratio, generally lead to larger CdSe nanoparticles. Bis(trimethylsilyl) selenium is the crucial precursor for the CdSe nanoparticle synthesis. An intermediate stage of the chemical reaction limiting the bis(trimethylsilyl) selenium production is described theoretically.      

Preparation of nanosize silica in reverse micelles: ethanol produced during TEOS hydrolysis affects the microemulsion structure

Microemulsions have been widely used as microreactors for the synthesis of nanoparticles and mesoporous materials. The correlation between the microstructure of a microemulsion and the features of the obtained materials is the most intriguing problem. On this point, many investigations have their ground on the structure of the precursor microemulsion, i.e., the system before the reaction takes place. Nevertheless, any reactions usually involve the formation of byproducts (aside from the nanoparticles). Several of these byproducts (e.g., ions, amphiphilic molecules) could modify the microemulsion structure during the course of the reaction. Here we examine the hydrolysis of tetraethoxysilane (TEOS) in the water-in-oil microemulsion hexadecyl-trimethylammonium bromide (CTAB)/pentanol/hexane/water. Conductivity and NMR measurements performed during the course of the reaction, in combination with dynamic light scattering and pulsed field gradient spin-echo NMR investigation performed on the microemulsion upon the addition of ethanol, indicate that a byproduct (ethanol) modifies the microreactor structure. The ethanol produced by the TEOS hydrolysis drives the microemulsion structure from small disconnected reverse micelles toward large connected aggregates until (for high enough ethanol loading) the system phase separates into two coexisting liquid phases (a dense interconnected network and a dilute reverse micellar phase).     

影响反相微乳液导电性能的因素

分别以聚乙二醇辛基苯基醚(Triton X-100)或十六烷基三甲基溴化铵(CTAB)为表面活性剂, 与正己烷、正己醇和水构成反相微乳液. 研究了水相H+浓度、表面活性剂、助表面活性剂等对微乳液导电性能的影响. 结果表明, 增加水相H+浓度可大幅度提高反相微乳液的导电能力, 当H+浓度由1.0 mol•L-1增加到10 mol•L-1时, 微乳液的电导率可提高1~2个数量级. 当水相H+浓度为10 mol•L-1时, 微乳液的电导率随溶水量的增大而增大, 水油体积比为3:10时, 两种体系的电导率均达到3200 μS•cm-1. Triton X-100浓度对微乳液的电导率影响较大, 电导率随其浓度增加而增大；而CTAB浓度对微乳液电导率的影响较小, 电导率随其浓度增加略有减小；助表面活性剂正己醇使非离子型反相微乳液的电导率下降, 而使阳离子型反相微乳液的电导率先增大, 然后减小, 呈骆峰状变化.     

微乳中纳米胶囊的复凝聚法制备

在O/W型APG微乳液模板上, 以明胶和阿拉伯树胶作为包裹材料, 用复凝聚的方法制备纳米胶囊, 对影响纳米胶囊的合成条件进行了分析. 用粒度仪测定产物的粒径及其分布, 用透射电镜观察产物的形貌. 结果表明, 用复凝聚法在微乳中合成了粒度均匀、粒径30～100 nm的球性纳米胶囊. 考察了微乳液的组成、高分子的浓度和复凝聚的条件对纳米胶囊性质的影响. 纳米胶囊对氯氰菊酯的包裹率较高, 在60%以上. 本方法条件温和, 操作简单, 是一种新型的纳米胶囊合成技术.     

层板剥离水滑石的制备及影响因素

采用阴离子表面活性剂N-月桂酰基谷氨酸(LG)为插层分子，研究了烷烃-LG-水(O/W)微乳液中烷烃量的变化对插层水滑石层间距的影响，同时研究了烷烃分子大小和水滑石层板阳离子不同对水滑石剥离难易程度的影响。实验表明，随着微乳液中烷烃含量的增加，制备得到了由插层到层板剥离的水滑石，并且烷烃的链长越长，水滑石的剥离越容易实现。层板化学组成对剥离难易程度也有影响，难易程度依次是Mg/Al-LDH，Zn/Al-LDH和Ni/Al-LDH。     

Polymerization of w/o microemulsions for the preparation of transparent SiO2/PMMA nanocomposites

Reverse w/o microemulsions composed of methyl methacrylate (MMA) forming the oil phase, nonionic surfactants, and water are used for the synthesis of transparent SiO2/PMMA nanocomposites. An inorganic precursor, tetraethoxysilane (Si(OEt)(4), TEOS), is hydrolyzed in the reverse micelles containing aqueous ammonia. During the hydrolysis of TEOS, polymerization of the continuous MMA phase is initiated using AIBN (azobisisobutyronitrile), and after thermal polymerization at 333 K for 12 h, solid blocks of PMMA are obtained in which nanometer-sized silica particles are trapped in the solid polymer matrix. According to small-angle X-ray and dynamic light scattering experiments, the water droplets in MMA microemulsions are 12 nm (R(W) = 13) in diameter, whereas after polymerization of the microemulsion, the SiO2 particles in the transparent SiO2/PMMA composites are 26 nm in diameter. Transmission electron micrographs demonstrate a low degree of agglomeration in the composites. In comparison with materials generated from micelle-free solutions, the particle size distribution is narrow. The reverse micelle-mediated approach produces composites of high transparency comparable with that of pure PMMA.     

Novel Synthesis of CeO2 Nanoparticles Within Formamide/Tri(ethyleneglycol)monododecyl Ether/n-Octane Nonaqueous Microemulsion Systems

The present study evaluates a new method to prepare Cerium oxide (CeO₂) nanoparticles by formamide/tri(ethyleneglycol)monododecyl ether (C₁₂E₃)/n-octane oil-continuous nonaqueous microemulsion. The effect of the polar phase (formamide/water) on the phase behavior, drop size, and conductivity behavior of the reverse microemulsion were investigated. X-ray diffraction (XRD) and transmission electron microscopy (TEM) were used to characterize the phase and morphology of synthesized CeO₂ nanoparticles. It was found that the CeO₂ powders synthesized within nonaqueous microemulsions and aqueous microemulisons had an average particle size of 30–50 nm and 15–40 nm, respectively. The experimental results indicate the formation mechanism of CeO₂ nanoparticles in formamide nonaqueous microemulsion and aqueous microemulsion is similar, and the formamide nonaqueous microemulsion can be used as nanoreactors for preparation of nanoparticles.