Effects of alkali metal ions on the thermal decomposition of ammonium heptamolybdate tetrahydrate

The thermal decomposition of pure ammonium heptamolybdate tetrahydrate (AHMT), and doped with Li⁺, Na⁺ and K⁺ ions was investigated using thermogravimetry, differential thermal analysis, infrared and X-ray diffraction techniques. Results obtained revealed that the decomposition of AHMT proceeded in three decomposition stages in which both NH₃ and H₂O were released in all stages. The presence of 0.5 mol % alkali metal ions enhances the formation of the intermediateb (NH₄)₂MO₇O₂₂·2H₂O while the decomposition of this intermediate into MoO₃ is slightly affected in the presence of all dopant concentrations used. The infrared absorption spectra of the thermal products of AHMT treated with 10 mol% alkali metal ions (AMI) at 350°C indicated a reduction of some Mo⁶⁺ ions. By heating of AHMT above 500°C in presence of 5 or 10 mol % of AMI, a solid-solid interaction between alkali metal oxides and MoO₃ giving rise to well crystallized alkali metal molybdates. finally the activation energies accompanied various decomposition stages were calculated.     

Evaluation of magnesium sulphate attack in mortar-metakaolin system by thermal analysis

This paper reports an experimental study on the magnesium sulphate resistance of mortar specimens incorporating 0, 10 and 20% of metakaolin (MK). The evidence of the attack was evaluated through the content of calcium hydroxide (portlandite) and formation of magnesium hydroxide (brucite) by thermal analysis (thermogravimetric and derivative thermogravimetric analysis). The mechanical degradation of the mortar specimens was evaluated through splitting tensile tests after 200 days of exposition to the magnesium solution. The addition of metakaolin resulted in a reduction in the content of calcium hydroxide and in a smaller formation of brucite in comparison with reference mixture. A tensile strength loss of about 7% was observed for the metakaolin mortars submitted to the magnesium solution attack for 200 days.     

硫酸铵的热分解

目前 ,关于各种无机酸铵盐的热分解情况都研究得比较清楚 ,但关于硫酸铵热分解情况的报道结果则不一致[1 - 7] 。本文对硫酸铵在各种温度下的常量热分解进行了研究 ,探讨其热分解机理 ,以利于对磷石膏 (主要成分为ＣａＳＯ4)的开发利用提供新的思路和方法[8] 。1　实验坩锅炉中热分解　约 1 0ｇ(ＮＨ4) 2 ＳＯ4置于恒重坩埚中 ,再放入坩埚炉中升温至设定温度 ,恒温0 5ｈ ,取出冷却 ,称重。并将坩埚中残余物用水溶解 ,测定水溶液中的Ｈ+、ＮＨ+4、ＳＯ2 -4 等离子的含量。其中ＮＨ+4含量采用甲醛法测定 ,ＳＯ2 -4 含量采用硫酸钡重量法测定…     

Calorimetric study and thermal analysis of berberine sulphate

The heat capacities of berberine sulphate [(C₂₀H₁₈NO₄)₂SO₄·3H₂O] were measured from 80 to 390 K by means of an automated adiabatic calorimeter. Smoothed heat capacities, H _T-H _298.15 and S _T-S _298.15 were calculated. The loss of crystalline water started at about 339.3±0.2 K, and its peak temperature was 365.8±0.6 K. The peak temperature of decomposition for berberine sulphate was at about 391.4±0.4 K by DSC curve. TG-DTG analysis of this material was carried out in temperature range from 310 to 970 K. TG and DSC curves show that there is no melting in the whole heating process. This revised version was published online in August 2006 with corrections to the Cover Date.     

The effect of sampling conditions on the thermal decomposition of electrolytic manganese dioxide

The effect of sampling conditions on the decomposition of electrolytic manganese dioxide using thermal methods is reported. Significant differences were observed in the mechanism of the decomposition by simply changing the reaction environment from a closed pan to an open pan configuration. The purge gas atmosphere was also observed to influence the decomposition mechanism. As a product of the decomposition is oxygen, the change in the mechanism observed between the experimental conditions may be explained in terms of the ease of removal of oxygen from the reaction site. This revised version was published online in August 2006 with corrections to the Cover Date.     

Phase changes in the syrian phosphorite–ammonium sulphate system

With a complex of physico-chemical methods for analysis it is proved that in the course of mechanochemical treatment of a Syrian phosphorite and ammonium sulphate mixture new phases have been formed. The thermal analysis proves an increase in the reaction properties of the ammonium sulphate and the Syrian phosphorite which is a prerequisite for the increase in the content of P₂O₅^assimilated , in the activated phosphorite mixtures and the possibility to use them in the production of NP complex fertilizers.     

硫酸铵-碘化钾-乙醇体系萃取分离钯

传统的萃取分离法主要是采用与水互不相溶的有机溶剂作萃取溶剂,有的反应速度慢,传质速率低,分配比较小而需要在振荡器上进行较长时间振荡或多次萃取才能达到定量萃取的目的。均相萃取、异相分离萃取体系可以克服异相萃取分离技术中的一些缺点而受到重视[1,2]。本文以乙醇为萃取溶剂,均相萃取、异相分离Pd(Ⅱ)。试验表明硫酸铵存在下乙醇与水分相过程中,Pd(Ⅱ)与I-开成的PdI42-与质子化乙醇(C2H5OH2+)形成电中性的缔合物(C2H5OH2+)2·PdI42-被乙醇相萃取,能使Pd(Ⅱ)从Fe(Ⅲ)、Al(Ⅲ)、Zn(Ⅱ)、Mn(Ⅱ)、Ni(Ⅱ)、Cr(Ⅲ)、Co(Ⅱ)…     

Non-isothermal kinetic applied to thermal decomposition of commercial alkyd varnish

Summary PHB polyester poly(3-hydroxybutyrate) is an interesting biodegradable polymer and intensively investigated as cast and sheet films with applications in food industry or in medicine. The films obtained are typically brittle and many scientists have attempted to reduce this brittleness by blending with other polymers. PHB from Usina da Pedra was blended with PEG poly(ethyleneglycol) 300 resulting in blend 1 and blend 2. The two mixtures were melted at 200 and quenched at 0°C. TG curves showed that the thermal stability of the blends and the PHB are identical. For these blends the crystallization temperature decreased compared to the pure PHB, which is probably due to the lower nucleation density.     

聚缩水甘油硝酸酯的热安定性和相容性研究

采用DSC、TG热分析方法研究了聚缩水甘油硝酸酯(PolyGLYN)的热安定性和与1,3,5-三硝基-1,3,5-三氮杂环己烷(RDX)间的相容性.结果表明,PolyGLYN在100℃以前较为稳定.当加热速率趋于零时PolyGLYN的热分解峰温为196.4℃,由Ozawa法计算的热分解表观活化能为182.0 kJ·mol-1,分别比RDX的低15.1℃和高22.2 kJ·mol-1.PolyGLYN热稳定性与RDX接近,两者之间的相容性较好.     

Thermal decomposition of sodium aluminium sulphate crystallohydrate

Dynamic TG investigations were carried out to elucidate the mechanism of thermal decomposition of aluminium sodium sulphate crystallohydrate. Shimadzu 31H and MOM Derivatograph X-ray diffraction and other techniques were used to determine data on the decomposition, activation energy, structure and phases in the solid products. Isothermal study in the temperature ranges 883–958 K and 983–1113 K in air or a reducing gas atmosphere revealed different reaction mechanisms. Depending on the experimental conditions, mainly Al₂O₃ can be obtained.     

Thermal behavior study and decomposition kinetics of salbutamol under isothermal and non-isothermal conditions

The thermal decomposition of salbutamol (β₂ — selective adrenoreceptor) was studied using differential scanning calorimetry (DSC) and thermogravimetry/derivative thermogravimetry (TG/DTG). It was observed that the commercial sample showed a different thermal profile than the standard sample caused by the presence of excipients. These compounds increase the thermal stability of the drug. Moreover, higher activation energy was calculated for the pharmaceutical sample, which was estimated by isothermal and non-isothermal methods for the first stage of the thermal decomposition process. For isothermal experiments the average values were E _act=130 kJ mol⁻¹ (for standard sample) and E _act=252 kJ mol⁻¹ (for pharmaceutical sample) in a dynamic nitrogen atmosphere (50 mL min⁻¹). For non-isothermal method, activation energy was obtained from the plot of log heating rates vs. 1/T in dynamic air atmosphere (50 mL min⁻¹). The calculated values were E _act=134 kJ mol⁻¹ (for standard sample) and E _act=139 kJ mol⁻¹ (for pharmaceutical sample).     

Effects of various atmospheres and some metal oxide additives on the thermal decomposition on ammonium chromate

The thermal decomposition of ammonium chromate (AC) in dynamic air, CO₂ and N₂ and in static atmospheres and in the presence of MoO₃, V₂O₅, Fe₂O₃, CuO, MnO₂ and Nd₂O₃ additives was studied by means of TG, DTA, IR spectroscopy and electrical conductivity measurements. It was found that AC decomposes in four stages, forming unstable intermediates which produce Cr₂O₃ as a final product. The presence of the different atmospheres and the oxide additives affected the decompositions of these intermediates and the oxidation state of the chromium ions. Finally, the mechanisms associated with the different decomposition stages are discussed.     

MgAl-水滑石热分解过程动力学研究

类水滑石化合物Hydrotalcite-like Compounds(简称HTLcs)又称阴离子粘土,是由带正电荷的氢氧化物层和层间阴离子构成[1]。由于在类水滑石结构中含有大量的结构羟基和层间可分解的阴离子,所以其热稳定性较差,易于分解形成具有一定酸碱性及大比表面的复合氧化物,该复合氧化物由于具有晶粒小、活性元素分布均匀、比表面积大等特点,表现出了优异的催化性能[2~5]。近年来,以HTLcs为前体经高温焙烧制备双金属复合氧化物备受关注[6]。揭示类水滑石热解机理、选择焙烧条件是催化剂制备的关键所在。本文利用TG-DTA技术详细研究了不同镁铝比HTL…     

Non-isothermal kinetic study of the thermal decomposition of diaminoglyoxime and diaminofurazan

Data on the thermal stability of organic materials such as diaminofurazan (DAF) and diaminoglyoxime (DAG) was required in order to obtain safety information for handling, storage and use. These compounds have been shown to be a useful intermediate for the preparation of energetic compounds. In the present study, the thermal stability of the DAF and DAG was determined by differential scanning calorimetery (DSC) and simultaneous thermogravimetery-differential thermal analysis (TG-DTA) techniques. The results of TG analysis revealed that the main thermal degradation for the DAF and DAG occurs in the temperature ranges of 230–275°C and 180–230°C, respectively. On the other hand, the TG-DTA analysis of compounds indicates that DAF melts (at about 182°C) before it decomposes. However, the thermal decomposition of the DAG started simultaneously with its melting. The influence of the heating rate (5, 10, 15 and 20°C min⁻¹) on the DSC behaviour of the compounds was verified. The results showed that, as the heating rate was increased, decomposition temperatures of the compounds were increased. Also, the kinetic parameters such as activation energy and frequency factor for the compounds were obtained from the DSC data by non-isothermal methods proposed by ASTM E698 and Ozawa. Based on the values of activation energy obtained by ASTM and Ozawa methods, the following order in the thermal stability was noticed: DAF>DAG.     

Thermal analysis of the polymerization process on the surface of inorganic fillers

The thermal polymerization of pentabromobenzyl (mono)acrylate (PBB-MA) on the surface of the inorganic fillers Mg(OH)₂ and CaCO₃ was studied. FTIR spectroscopy and extraction of the polymer in bromobenzene show that polypentabromobenzyl acrylate (PBB-PA) was mostly grafted on the surface of Mg(OH)₂. Thermal analysis (TG, DSC, isothermal DSC (IDSC)) demonstrated an increase in polymerization starting temperature, and differences in polymerization enthalpy and apparent activation energy when an inorganic filler is added. These differences depend on the chemical composition of the filler used.The authors acknowledge valuable discussions with Prof. S. Yariv. The authors are also grateful to Berecha Foundation (Geneva) for the financial support of this work.     

Effect of cerium, holmium and samarium ions on the thermal and structural properties of the HZSM-12 zeolite

The study of the incorporation of rare earth elements as additives in Y zeolites is a very interesting field of research, mainly by its potential application as additives in catalytic cracking process. In this work was studied the thermal and structural properties of cerium, holmium and samarium supported on HZSM-12 zeolite. The obtained materials were characterized by X-ray diffraction (XRD), infrared spectroscopy (FTIR), nitrogen adsorption, thermogravimetry (TG/DTG), differential scanning calorimetry (DSC) and differential thermal analysis (DTA). TG/DSC/DTA analyses showed that the dehydration temperatures of RE/HZSM-12 zeolites (RE=Ce, Ho, Sm) increase in relation to pure HZSM-12. The acid properties were investigated by pyridine thermo desorption via TG. The results showed two events of mass loss attributed to elimination of pyridine adsorbed on the weak+medium acid sites and on the strong acid sites.     

Kinetic and activation thermodynamic parameters on thermal decomposition of synthetic lubricant oils

The kinetic and thermodynamic study of synthetic lubricant oils was accomplished in this work, using isothermal and non-isothermal thermogravimetry based on mass loss as a function of time and temperature. The thermodynamic and kinetic behavior of the synthetic lubricant oils depends on atmosphere and heating rates used in TG analysis. The kinetic and thermodynamic results were satisfactory, presenting good correlation.     

Determination of codeine phosphate and codeine in thermal characterization by differential scanning calorimetry

Thermal behaviour of codeine phosphate and codeine crystallized at the several solvents system was studied by DSC, and then, the kinetic parameters and thermochemical data have been obtained. We have found that codeine phosphate and codeine exist in a number of polymorphic formes which may inflicence the bio-availability.     

硫酸高铈铵分光光度法测定葡萄籽提取物中原花青素

建立了葡萄籽提取物中原花青素测定的新方法 硫酸高铈铵分光光度法。它是基于原花青素与Ce4 在强酸性介质中反应生成无色的Ce3 ,通过测定黄色高铈盐的吸光度,间接测定原花青素,Ce4 在319nm波长处具有最大吸收。该方法的线性范围为0.12～10μg mL,RSD为0.98%～1.1%,回收率为97.2%～102.8%,相关系数r=0.9992,检出限为0.04μg mL。