Direct detection of explosives on solid surfaces by mass spectrometry with an ambient ion source based on dielectric barrier discharge

Trace amounts of explosives on solid surfaces were detected by mass spectrometry at ambient conditions with a new technique termed dielectric barrier discharge ionization (DBDI). By the needle-plate discharge mode, a plasma discharge with energetic electrons was generated, which could launch the desorption and ionization of the explosives from solid surfaces. Hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 2,4,6-trinitrotoluene (TNT), and pentaerythritol tetranitrate (PETN) were desorbed directly from the explosives-contaminated surface by DBDI, forming the typical anions of [TNT](-), [TNT - H](-), [RDX + NO(2)](-), [PETN + ONO(2)](-), and [RDX + ONO(2)](-). The ions were transferred into the MS instrument for analysis in the negative ion mode. The detection limit of present method was 10 pg for TNT (m/z 197, S/N 8 : 1), 0.1 ng for RDX (m/z 284, S/N 10 : 1), and 1 ng for PETN (m/z 260, S/N 12 : 1). The present method allowed the detection of trace explosives on various matrices, including paper, cloth, chemical fiber, glass, paints, and soil. A relative standard deviation of 5.57% was achieved by depositing 100 pg of TNT on these matrices. The analysis of A-5, a mixture of RDX and additives, has been carried out and the results were consistent with the reference values. The DBDI-MS method represents a simple and rapid way for the detection of explosives with high sensitivity and specificity, which is especially useful when they are present in trace amounts on ordinary environmental surfaces.     

Detection of explosives on skin using ambient ionization mass spectrometry

Single nanogram amounts of the explosives TNT, RDX, HMX, PETN and their mixtures were detected and identified in a few seconds on the surface of human skin without any sample preparation by desorption electrospray ionization (DESI) using a spray solution of methanol-water doped with sodium chloride to form the chloride adducts with RDX, HMX, and PETN while TNT was examined as the radical anion and tandem mass spectrometry was used to confirm the identifications.     

Optimized thermal desorption for improved sensitivity in trace explosives detection by ion mobility spectrometry

In this work we evaluate the influence of thermal desorber temperature on the analytical response of a swipe-based thermal desorption ion mobility spectrometer (IMS) for detection of trace explosives. IMS response for several common high explosives ranging from 0.1 ng to 100 ng was measured over a thermal desorber temperature range from 60 °C to 280 °C. Most of the explosives examined demonstrated a well-defined maximum IMS signal response at a temperature slightly below the melting point. Optimal temperatures, giving the highest IMS peak intensity, were 80 °C for trinitrotoluene (TNT), 100 °C for pentaerythritol tetranitrate (PETN), 160 °C for cyclotrimethylenetrinitramine (RDX) and 200 °C for cyclotetramethylenetetranitramine (HMX). By modifying the desorber temperature, we were able to increase cumulative IMS signal by a factor of 5 for TNT and HMX, and by a factor of 10 for RDX and PETN. Similar signal enhancements were observed for the same compounds formulated as plastic-bonded explosives (Composition 4 (C-4), Detasheet, and Semtex). In addition, mixtures of the explosives exhibited similar enhancements in analyte peak intensities. The increases in sensitivity were obtained at the expense of increased analysis times of up to 20 seconds. A slow sample heating rate as well as slower vapor-phase analyte introduction rate caused by low-temperature desorption enhanced the analytical sensitivity of individual explosives, plastic-bonded explosives, and explosives mixtures by IMS. Several possible mechanisms that can affect IMS signal response were investigated such as thermal degradation of the analytes, ionization efficiency, competitive ionization from background, and aerosol emission.     

Thermal Analysis of Binary Systems. Explosive – lead compound

The thermal decomposition of explosives: pentaerythrol tetranitrate (PETN), 2,4,6-trinitrotoluene(TNT), cyclo-1,3,5-trimethylene-2,4,6-trinitroamine (RDX) and their two-component mixtures with 40% of lead compounds [PbO, Pb₃O₄, Pb(NO₃)₂] were performed. The simple method of determination of stability changes in the mixtures described above, in comparison with pure explosives was presented. The lead oxides accelerated significantly the thermal decomposition of explosives. Pb(NO₃)₂ acts as a catalyst in the mixture containing TNT degradation, but not in a case of PETN and RDX. This revised version was published online in August 2006 with corrections to the Cover Date.     

Low‐pressure barrier discharge ion source using air as a carrier gas and its application to the analysis of drugs and explosives

In this work, a low‐pressure air dielectric‐barrier discharge (DBD) ion source using a capillary with the inner diameter of 0.115 and 12 mm long applicable to miniaturized mass spectrometers was developed. The analytes, trinitrotoluene (TNT), 1,3,5‐trinitroperhydro‐1,3,5‐triazine (RDX), 1,3,5,7‐tetranitroperhydro‐1,3,5,7‐tetrazocine (HMX), pentaerythritol tetranitrate (PETN), nitroglycerine (NG), hexamethylene triperoxide diamine (HMTD), caffeine, cocaine and morphine, introduced through the capillary, were ionized by a low‐pressure air DBD. The ion source pressures were changed by using various sizes of the ion sampling orifice. The signal intensities of those analytes showed marked pressure dependence. TNT was detected with higher sensitivity at lower pressure but vice versa for other analytes. For all analytes, a marked signal enhancement was observed when a grounded cylindrical mesh electrode was installed in the DBD ion source. Among nine analytes, RDX, HMX, NG and PETN could be detected as cluster ions [analyte + NO₃]^? even at low pressure and high temperature up to 180 °C. The detection indicates that these cluster ions are stable enough to survive under present experimental conditions. The unexpectedly high stabilities of these cluster ions were verified by density functional theory calculation. Copyright © 2016 John Wiley & Sons, Ltd.     

Micellar extraction and high performance liquid chromatography-ultra violet determination of some explosives in water samples

An analytical method based on the cloud point extraction combined with high performance liquid chromatography is used for the extraction, separation and determination of four explosives; octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazine (HMX), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 2,4,6-trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN). These compounds are extracted by using of Triton X-114 and cetyl-trimethyl ammonium bromide (CTAB). After extraction, the samples were analyzed using a HPLC-UV system. The parameters affecting extraction efficiency (such as Triton X-114 and CTAB concentrations, amount of Na₂SO₄, temperature, incubation and centrifuge times) were evaluated and optimized. Under the optimum conditions, the preconcentration factor was 40 and the improvement factors of 34, 29, 61 and 42 with detection limits of 0.09, 0.14, 0.08 and 0.40 (μg L⁻¹) were obtained for HMX, RDX, TNT and PETN, respectively. The proposed method was successfully applied to the determination of these compounds in water samples and showed recovery percentages of 97-102% with RSD values of 2.13-4.92%.     

Fabric analysis by ambient mass spectrometry for explosives and drugs

Desorption electrospray ionization (DESI) is applied to the rapid, in-situ, direct qualitative and quantitative analysis of mixtures of explosives and drugs from a variety of fabrics, including cotton, silk, denim, polyester, rayon, spandex, leather and their blends. The compounds analyzed were explosives: trinitrohexahydro-1,3,5-triazine (RDX), octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), 2,4,6-trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN) and the drugs of abuse: heroin, cocaine, and methamphetamine. Limits of detection are in the picogram range. DESI analyses were performed without sample preparation and carried out in the presence of common interfering chemical matrices, such as insect repellant, urine, and topical lotions. Spatial and depth profiling was investigated to examine the depth of penetration and lateral resolution. DESI was also used to examine cotton transfer swabs used for travel security sample collection in the screening process. High throughput quantitative analysis of fabric surfaces for targeted analytes is also reported.     

Compatibility of PNIMMO with some energetic materials

The compatibility of poly(3-nitromethyl-3-methyloxetane) (PNIMMO) with some energetic materials are studied by using pressure DSC method in detail. Cyclotetramethylenetetranitroamine (HMX), cyclotrimethylenetrinitramine (RDX), nitrocellulose (NC), nitroglycerine (NG), N-nitrodihydroxyethylaminedinitrate (DINA), and aluminum powder (Al) are used as common energetic materials, and 3,4-dinitrofurzanfuroxan (DNTF), 1,3,3-trinitroazetidine (TNAZ), hexanitrohexazaisowurtzitane (CL-20), 4,6-dinitro-5,7-diaminobenzenfuroxan (CL-14), 1,1-diamino-2,2-dinitroethylene (DADNE), and 4-amino-5-nitro-1,2,3-triazole (ANTZ) are used as new energetic materials. The results show that the binary systems of PNIMMO with HMX, RDX, NC, NG, DINA, Al, CL-14 and DADNE are compatible, with TNAZ, CL-20 and ANTZ are slightly sensitive, and with DNTF is sensitive.     

Voltammetric determination of nitroaromatic and nitramine explosives contamination in soil

The contamination of soil by nitroaromatic and nitramine explosives is widespread during the manufacture, testing and disposal of explosives and ammunitions. The analysis for the presence of trace explosive contaminants in soil becomes important in the light of their effect on the growth of different varieties of plants and crops. 2,4,6-Trinitrotoluene (TNT), cyclotrimethylene trinitramine (Research Department explosive, RDX) and cyclotetramethylene tetranitramine (high melting point explosive, HMX), other related explosive compounds and their by-products must be monitored in soil and surrounding waterways since these are mutagenic, toxic and persistent pollutants that can leach from the contaminated soil to accumulate in the food chain. In this study, a voltammetric method has been developed for the determination of explosive such as RDX, HMX and TNT. The electrochemical redox behavior of RDX, HMX and TNT was studied through cyclic voltammetry and quantitative determination was carried out by using square wave voltammetry technique. Calibration curves were drawn and were linear in the range of 63-129 ppm for RDX with a detection limit of 10 ppm, 49-182 ppm for HMX with a detection limit of 1 ppm and 38-139 ppm for TNT with a detection limit of 1 ppm. This method was applied to determine the contaminations in several soil samples that yielded a relative error of 1% in the concentrations.     

A systematic tandem mass spectrometric study of anion attachment for improved detection and acidity evaluation of nitrogen‐rich energetic compounds

The development of rapid, efficient, and reliable detection methods for the characterization of energetic compounds is of high importance to security forces concerned with terrorist threats. With a mass spectrometric approach, characteristic ions can be produced by attaching anions to analyte molecules in the negative ion mode of electrospray ionization mass spectrometry (ESI‐MS). Under optimized conditions, formed anionic adducts can be detected with higher sensitivities as compared with the deprotonated molecules. Fundamental aspects pertaining to the formation of anionic adducts of 1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocane (HMX), 1,3,5‐trinitro‐1,3,5‐triazinane (RDX), pentaerythritol tetranitrate (PETN), nitroglycerin (NG), and 1,3,5‐trinitroso‐1,3,5‐triazinane energetic (R‐salt) compounds using various anions have been systematically studied by ESI‐MS and ESI tandem mass spectrometry (collision‐induced dissociation) experiments. Bracketing method results show that the gas‐phase acidities of PETN, RDX, and HMX fall between those of HF and acetic acid. Moreover, PETN and RDX are each less acidic than HMX in the gas phase. Nitroglycerin was found to be the most acidic among the nitrogen‐rich explosives studied. The ensemble of bracketing results allows the construction of the following ranking of gas‐phase acidities: PETN (1530‐1458 kJ/mol) > RDX (approximately 1458 kJ/mol) > HMX (approximately 1433 kJ/mol) > nitroglycerin (1427‐1327.8 kJ/mol).     

The very far-infrared spectra of energetic materials and possible confusion materials using terahertz pulsed spectroscopy

We have measured the terahertz absorption spectra of 1,3,5-trinitro-1,3,5-triazacyclohexane (RDX), pentaerythritol tetranitrate (PETN), 1,3,5,7-tetranitro-1,3,5,7-tetrazacyclooctane (HMX), 2,4,6-trinitrotoluene (TNT), the plastic explosives Semtex H, SX2, and Metabel, and a number of confusion materials using terahertz pulsed transmission spectroscopy. Spectral fingerprints were obtained from 3 to 133 cm⁻¹. The spectra of the plastic explosives are dominated by the spectral signatures of their explosive components due to low frequency vibrations and crystalline phonon modes. Importantly, the terahertz spectra of the confusion materials show no resemblance to the explosives spectra. The refractive indices obtained for the plastic explosives and confusion materials allowed us to derive reflectance spectra, which appear distinct and so suggest that terahertz reflection spectroscopy is a suitable tool for the detection of concealed explosives in security applications.     

Physico-chemical measurements of CL-20 for environmental applications. Comparison with RDX and HMX

CL-20 is a polycyclic energetic nitramine, which may soon replace the monocyclic nitramines RDX and HMX, because of its superior explosive performance. Therefore, to predict its environmental fate, analytical and physico-chemical data must be made available. An HPLC technique was thus developed to measure CL-20 in soil samples based on the US Environmental Protection Agency method 8330. We found that the soil water content and aging (21 days) had no effect on the recoveries (>92%) of CL-20, provided that the extracts were kept acidic (pH 3). The aqueous solubility of CL-20 was poor (3.6 mg l(-1) at 25 degrees C) and increased with temperature to reach 18.5 mg l(-1) at 60 degrees C. The octanol-water partition coefficient of CL-20 (log KOW = 1.92) was higher than that of RDX (log KOW = 0.90) and HMX (log KOW = 0.16), indicating its higher affinity to organic matter. Finally, CL-20 was found to decompose in non-acidified water upon contact with glass containers to give NO2- (2 equiv.), N2O (2 equiv.), and HCOO- (2 equiv.). The experimental findings suggest that CL-20 should be less persistent in the environment than RDX and HMX.     

Direct exposure chemical ionization mass spectra of explosives

Mass spectra of explosives, including TNT, tetryl, nitroglycerin, PETN and RDX have been recorded by direct exposure chemical ionization with isobutane as reagent at source temperatures of 50–100°C. The mass spectra contain major [MH]⁺ ions, adduct ions and some fragment ions. The configuration of the relative abundances of these ions has been found to be a function of temperature and source pressure. Maximum [MH]⁺ ion abundance has been obtained at source pressures much lower than normal chemical ionization pressures.     

Note on the use of the vacuum stability test in the study of initiation reactivity of attractive cyclic nitramines in Formex P1 matrix

The zero-order reaction rates (specific rate constants) of isothermal decomposition at 120 °C of plastic bonded explosives (PBXs) were measured by means of the Czech vacuum stability test, STABIL. The PBXs are based on 1,3,5-trinitro-1,3,5-triazinane (RDX), 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX), cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole (BCHMX), and ε 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (ε-HNIW, ε-CL-20) with 13 wt% of the Formex P1 type matrix, i.e., a matrix of the explosive with pentaerythritol tetranitrate (PETN) bound by 13 wt% of a mixture of 25 wt% of styrene–butadiene rubber and 75 wt% of an oily material. Dependencies were found between the specific rate constants mentioned and the detonation velocities of PBXs, and consequently between these constants and the impact and electric spark sensitivities of pure explosive fillers, i.e., RDX, HMX, HNIW, BCHMX, and PETN. It is stated that the higher impact or electric spark sensitivity of their pure explosive fillers corresponds to the higher thermal reactivity of the given PBXs.     

Fast gas chromatography-differential mobility spectrometry of explosives from TATP to Tetryl without gas atmosphere modifiers

Explosives in solution were determined as mixtures containing highly volatile improvised explosives such as peroxides and conventional military grade explosives such as PETN, RDX, and Tetryl using a high speed gas chromatograph with differential mobility detector in a single measurement. Instrument parameters were evaluated and adjusted to permit detection of nanogram amounts of explosives with this broad range of vapor pressures in times under 3 min for HMTD to TNT or under 16 min for HMTD to Tetryl. As in prior studies of response to explosives with mobility spectrometers, pre-separation of sample by gas chromatography improved response in the differential mobility detector; however, unlike prior configurations, the supporting gas atmosphere did not contain modifiers to adjust selectivity in mobility and selectivity was provided only by characteristic stability of product ions in negative and positive polarities. Field dependence of product ions in purified air was determined for each explosive and patterns were sufficiently distinct to suggest the addition of selectivity through the use of several differential mobility detectors operated in parallel or series with characteristic separation voltages.     

Theoretical studies of energy transfer rates of secondary explosives

Understanding the mechanism of shock-induced chemical reaction in secondary explosives is necessary to pursue the development and the safe use of new explosives having high performance and low sensitivity. In an effort to understand the mechanism, the energy transfer rates of such secondary explosives as PETN(I), PETN(II), delta-HMX, alpha-HMX, beta-HMX, RDX, ANTA, DMN, and NM have been evaluated based on the formula derived by Fried and Ruggiero [Fried, L. E.; Ruggiero, A. J. J. Phys. Chem. 1994, 98, 9786]. The energy transfer rates were determined in terms of the density of vibrational states and the unharmonic vibron-phonon coupling term, which were calculated by using a flexible potential containing both intra- and intermolecular terms. For the secondary explosives, a good correlation was found between the energy transfer rates and the impact sensitivity. The energy transfer rates are several times faster for the explosives with higher sensitivity such as PETN, HMX, and RDX than those with lower sensitivity such as ANTA, DMN, and NM. The calculations presented suggest the energy transfer rate in secondary explosive crystals is a significant factor in their sensitivity and introduction of double bond, or hydrogen bonds, or caged structure into secondary explosives is expected to decrease the sensitivity.     

Corrosion resistance of cement mortars containing spent catalyst of fluidized bed cracking (FBCC) as an additive

Compatibility is an important property for energetic materials and their additives such as a casing material or a binder. If these substances are incompatible an extra risk is introduced in handling and storage of ammunition and explosives. As part of a co-operation program between the Dutch TNO-PML and the Polish MIAT several compatibility tests are performed and compared with each other. All tests are performed according to a NATO Standard in which several tests are described which can be used to determine the compatibility of an energetic material and an additive. These tests were performed on a huge set of energetic materials e.g. propellants (single and double base), explosives (RDX, PETN, HMX and TNT) and several additives like Teflon, polypropylene, self-burning case, inhibitors etc. The results of pressure vacuum stability tests, dynamic thermogravimetry measurements and differential scanning calorimetry tests with several combinations of energetic materials and additives used during the co-operation program are presented and discussed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Decomposition of nitramine energetic materials in excited electronic states: RDX and HMX

Ultraviolet excitation (8-ns duration) is employed to study the decomposition of RDX (1,3,5-trinitro-1,3,5-triazacyclohexane) and HMX (1,3,5,7-tetranitro-1,3,5,7-tetrazacyclooctane) from their first excited electronic states. Isolated RDX and HMX are generated in the gas phase utilizing a combination of matrix-assisted laser desorption and supersonic jet expansion techniques. The NO molecule is observed as one of the initial dissociation products by both time-of-flight mass spectroscopy and laser-induced fluorescence spectroscopy. Four different vibronic transitions of NO are observed: A (2)Sigma(v(') = 0)<--X (2)Pi(v(") = 0,1,2,3). Simulations of the NO rovibronic intensities for the A<--X transitions show that dissociated NO from RDX and HMX is rotationally cold (approximately 20 K) and vibrationally hot (approximately 1800 K). Another potential initial product of RDX and HMX excited state dissociation could be OH, generated along with NO, perhaps from a HONO intermediate species. The OH radical is not observed in fluorescence even though its transition intensity is calculated to be 1.5 times that found for NO per radical generated. The HONO intermediate is thereby found not to be an important pathway for the excited electronic state decomposition of these cyclic nitramines.     

Analysis of 2,4,6-trinitrotoluene, pentaerythritol tetranitrate and cyclo-1,3,5-trimethylene-2,4,6-trinitramine using negative corona discharge ion mobility spectrometry

In this study, the capability of negative corona discharge ion mobility spectrometry (IMS) for quantitative magnitude of several explosives including 2,4,6-trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN) and cyclo-1,3,5-trimethylene-2,4,6-trinitramine (RDX) has been evaluated for the first time. The total current obtained with the negative corona discharge was about 100 times larger than that of IMS based on ⁶³Ni, which results in a lower detection limit and a wider linear dynamic range. The detection limits for PETN, TNT and RDX were 8×10⁻¹¹, 7×10⁻¹¹ and 3×10⁻¹⁰ g, respectively. The calibration plots for these explosives showed linear dynamic ranges of about four orders of magnitude.