Chemiluminescence flow sensor for folic acid with immobilized reagents.

A novel chemiluminescence (CL) sensor for folic acid combined flow-injection (FI) technology was presented in this paper. The analytical reagents involved in the CL reaction, including luminol and hexacyanoferrate(III), were both immobilized on an anion-exchange column in FI system. The CL signal produced by the reaction between luminol and hexacyanoferrate(III), which were eluted from the column through sodium phosphate injection, was decreased in the presence of folic acid. The CL emission was correlated with the folic acid concentration in the range from 0.01 to 15 microg ml(-1), and the detection limit was 3.5 ng ml(-1) folic acid (3sigma). At a flow rate of 2.0 ml min(-1), including sampling and washing, could be performed in 2 min with a relative standard deviation of < 2.5%. The flow sensor could be reused more than 300 times and has been applied to the analysis of folic acid in pharmaceutical preparations. and the recovery was from 97.4% to 100.4%.     

固相配位化学反应研究XXXIV. 室温下六氰合铁(II)及(III)酸钾 的固相酸碱反 应

本文研究了室温时K~3Fe(CN)~6,K~4Fe(CN)~6在酸碱条件下发生的固相配位化学反应。结果表明:K~3Fe(CN)~6与NaBH~4固相混合物室温下不反应,但加入固体氢氧化钠后,K~3Fe(CN)~6与NaBH~4的固相氧化还原反应在室温下很容易进行。K~4Fe(CN)~6与K~2S~2O~8的固相氧化还原反应在室温下能顺利进行,但当固体KOH存在时,反应明显受到抑制。K~3Fe(CN)~6与K~2C~2O~4.H~2O室温下无反应,但与H~2C~2O~4.2H~2O在室温时即发生固相取代反应。     

Simultaneous anodic stripping voltammetric determination of lead and cadmium with a carbon paste electrode modified by tributyl phosphate

A novel chemiluminescence (CL) flow sensor has been developed for the monitoring of iron(III). The analytical reagents involved in the CL reaction, including luminol and hexacyanoferrate(II) were both immobilized on an anion-exchange resin column. When sodium sulfate solution was passed through the column, these two reagents were eluted from the resins and then mixed with an iron(III) stream. By the fast reaction between iron(III) and hexacyanoferrate(II), the complex Prussian Blue was generated, which could catalyse the luminol oxidation by dissolved oxygen in alkaline aqueous solution to produce CL. The CL emission intensity was correlated with the standard iron(III) concentration in the range 0.01-Smgl^–1, and the detection limit was 7 × 10^–3mgl^–1 iron(III). A complete analysis, including sampling and washing, could be performed in l min with a relative standard deviation of less than 5%. The sensor was stable for over 200 times and has been applied successfully to the determination of iron in blood samples.     

Determination of ceftriaxone sodium in pharmaceutical formulations by flow injection analysis with acid potassium permanganate chemiluminescence detection.

Based on the chemiluminescence (CL) emission generated from the oxidation of ceftriaxone sodium alkali hydrolysate by potassium permanganate in polyphosphoric acid (PPA), a novel determination method for ceftriaxone sodium was developed by using a flow-injection technique. The calibration curve appears to be linear in the range between 0.05 and 100 microg mL(-1) with a detection limit (3sigma) of 25 ng mL(-1), and a relative standard deviation (RSD) of 0.6% for eleven replicate determinations of 5.0 microg mL(-1) ceftriaxone sodium. The proposed method has been successfully utilized for the determination of ceftriaxone sodium in pharmaceutical formulations, while the chemiluminescence reaction mechanisms were investigated.     

高效液相色谱—化学发光法研究异烟肼和利福平

基于异烟肼和利福平在碱性介质中能与K3Fe(CN)6反应产生强的化学发光，因 此设计了一个经高效液相色谱（HPLC）分离柱后同时检测一线抗结构病药物异烟肼 、利福平的化学发光检测器。研究并优化了流动相、流速以及化学发光检测的条件 。该方法测定异烟肼、利福平的线性范围分别为0.05～6.0mg/L，0.08～20.0mg/L ，其检出限：异烟肼为2×10^-2mg/L，利福平为4×10^-2mg/L，测定的相对标准偏 差分别为1.9，2.9。该方法已成功地用于同时测定复方利福平片中利福平和异烟肼 的含量。     

Chemiluminescence Flow Injection Analysis of Menadione Sodium Bisulfite Based on Luminol Reaction

ABSTRACT

A chemiluminescence(CL) flow system is described for the determination of menadione sodium bisulfite based on its repression on the chemiluminescence(CL) emission produced upon mixing a hexacyanoferrate(III) solution with an alkaline luminol solution in the absence of co-oxidizer. The system responds linearly to menadione sodium bisulfite concentration in the range 0-1 μg/mL with a detection limit (3σ) of 0.01 μg/mL. Relative standard deviation (RSD) of 0.16% for 0.4 μg/mL menadione sodium bisulfite (n=11). The system has been successfully applied to the determination of menadione sodium bisulfite in tablets and injections.     

铁氰化钾化学发光体系测定芦丁

基于在ＮａＯＨ碱性介质中,Ｆｅ（ＣＮ）３－６可以直接氧化芦丁产生强的化学发光这一现象,并结合流动注射分析技术,提出了一种直接化学发光测定芦丁的新方法。该方法测定芦丁的线性范围为１×１０－４～　１×１０－６　ｇ／ｍＬ,检出限为３．４×１０－７　ｇ／ｍＬ（３σ）。对５×１０－６　ｇ／ｍＬ芦丁溶液连续１１次测量的相对标准偏差为３．７％。该方法已成功地用于药片中芦丁含量的测定。     

Kinetic spectrophotometric determination of low levels of nitrite by catalytic reaction between pyrogallol red and bromate

A kinetic spectrophotometric method for the determination of trace nitrite (0.003-1.000 microg/ml) based on its catalytic effect on the reaction between potassium bromate and pyrogallol red in acidic media is described. The reaction is monitored spectrophotometrically by measuring the decreasing colour of pyrogallol red at 467 nm by the fixed-time method. At a given time of 3.0 min at 30 degrees, the detection limit is 0.001 microg/ml and the relative standard deviation for 0.010 microg/ml nitrite is 1.8% (n = 8). The method is free from most interferences, especially from large amounts of nitrate and ammonium. The procedure was successfully applied to the determination of trace nitrite in natural water without preconcentration.     

A flow injection chemiluminescence system for the determination of isoniazid

A chemiluminescence (CL) flow system is described for the determination of isoniazid based on its enhancement on the chemiluminescence (CL) emission produced upon mixing a hexacyanoferrate(III) solution with an alkaline luminol solution. The system responds linearly to isoniazid concentration in the range 0-1 mg/L with a detection limit (3sigma) of 0.03 microg/L, relative standard deviation (RSD) of 1.2% for 0.1 mg/L isoniazid (n = 11). The system has been successfully applied to the determination of isoniazid in pharmaceutical preparations.     

Flow-injection chemiluminescence determination of formaldehyde with a bromate-rhodamine 6G system.

In this paper, a novel flow-injection chemiluminescence (CL) system for the determination of formaldehyde is described. It is based on a strong enhance effect of formaldehyde on the weak CL emission of the reaction between potassium bromate and rhodamine 6G in a sulfuric acid medium. A possible mechanism for this CL reaction is proposed. A CL calibration graph was linear in the range of 0.8 - 200 microg l(-1) and the detection limit was 0.3 microg l(-1) (3sigma). The relative standard deviation was less than 3% for 10 microg l(-1) formaldehyde (n = 11). The method has been applied to determine formaldehyde in the air samples.     

A new chemiluminescence method for the determination of nickel ion

A new chemiluminescence (CL) phenomenon described as the second-chemiluminescence (SCL) was observed and a strong CL signal was detected, when Ni(II) ion was injected into the mixture after the end of the reaction of potassium permanganate with alkaline luminol. The possible CL mechanism is proposed based on the kinetic curve of the CL reaction, CL spectra, UV-vis spectra and some other experiments. A flow-injection analysis for the determination of nickle(II) ion has been developed, based on the catalysis of nickel(II) ion on the CL reaction between potassium manganate produced on-line and luminol under alkaline condition. Under the optimum conditions, the SCL intensity is linear with the concentration of nickel(II) ion in the range of 8.0-200.0 microg l-1 and 0.2-2.0 mg l-1. The R.S.D. was 4.5% for 11 determinations of 250 microg l-1 nickel(II) ion and the detection limit (3sigma) for nickel(II) ion was 0.33 microg l-1. The method was applied to determine nickel(II) ion in synthetic samples with satisfactory results.     

Sensitive monitoring of humic acid in various aquatic environments with acidic cerium chemiluminescence detection.

In this research, a simple, sensitive chemiluminescence (CL) method for the determination of humic acid (HA) in water samples was first developed based on the redox reaction between humic acid and cerium(IV) in the acidic condition. Different with the former redox CL reaction which occurred in alkaline solution, no enhancers were needed and neither precipitation nor a second contamination would occur in the present CL system. Comparing with other spectrometric methods, we find that the proposed analysis system had better applicability and accuracy. Under the optimal experiment conditions, the CL peak height was linear with the concentration of HA in the range of 0.03 to 10.0 microg mL(-1). The detection limit is 0.01 microg mL(-1) (S/N = 3), and the relative standard deviation was 2.3% for 0.5 microg mL(-1) HA solution with eleven repeated measurements. The present CL method was successfully applied to the determination of HA in tap water, spring water and river water samples with good recovery from 90.0 to 110.0%. A possible CL mechanism was proposed based on the results of UV and fluorescence spectrometry and the CL spectrum of HA. It was speculated that the semi-quinone radicals in the excited state were the emitters.     

Rapid and sensitive determination of aminoglycoside antibiotics in water samples using a strong cation-exchange chromatography non-derivatisation method with chemiluminescence detection

A simple and sensitive chemiluminescence (CL) detection approach was developed for the direct analysis of aminoglycoside antibiotics in water samples following strong cation-exchange chromatographic (SCX-HPLC) separation. This detection system, which eliminates the need for sample derivatisation, is based on the inhibitory effect of aminoglycosides on the CL reaction between luminol and hydrogen peroxide catalysed by copper(II). As the operational and chemical variables that affect the CL signal were optimised, ionic strength and the Triton X-100 micelles turned out to be the keys to obtain maximum CL efficiency. Aminoglycosides were successfully separated in 10 min on a SCX column using a mobile phase consisting of an aqueous solution containing 5.0 x 10(-3)mol/l sodium acetate and 0.65 mol/l sodium chloride at pH 6.1. Sample volumes of 50 ml were preconcentrated by passage through a weakly acidic IRC-50 exchange column. Limits of detection from 0.7 to 10 microg/l and relative standard deviations from 2.7 to 5.4% were thus obtained. The proposed method surpasses other chromatographic alternatives in terms of the limit of detection, sample requirements for analysis and cost.     

Kinetics and mechanism of palladium (II) chloride catalyzed oxidation of allyl alcohol by potassium hexacyanoferrate (III)

A kinetic study of the oxidation of allyl alcohol by potassium hexacyanoferrate (III) in the presence of palladium (II) chloride is reported. The reaction was observed by measuring the disappearance of the potassium hexacyanoferrate (III) spectrophotometrically. The reaction is first order with respect to allyl alcohol and palladium (II) chloride, inverse second order with respect to [Cl^?], and zero order with respect to potassium hexacyanoferrate (III). The rate is found to increase linearly with hydroxyl ion concentration.     

流动注射化学发光法快速测定尿液中左亚叶酸钙

在碱性介质中, 左亚叶酸钙对鲁米诺-K3Fe(CN)6体系有显著的增敏作用, 据此, 建立了一种简单、快速测定左亚叶酸钙的流动注射化学发光新方法. 在优化的实验条件下, 该法测定左亚叶酸钙的线性范围为5.0×10-8～1.0×10-5 g/mL; 检出限(3σ)为2.0×10-8 g/mL; 对浓度为1.0×10-6 g/mL的样品进行11次平行测定, 相对标准偏差为1.3%. 将此法用于尿液中左亚叶酸钙的测定, 同时进行回收率实验.     

Rapid and sensitive determination of tryptophan, serotonin and psychoactive tryptamines by thin-layer chromatography/fluorescence detection

A rapid, sensitive and selective method for the determination of tryptophan (Trp), serotonin (5-HT) and psychoactive tryptamines (PATs) by thin-layer chromatography (TLC) with fluorescence detection is proposed. These compounds form fluorophores on the developing plate by heating after spraying with sodium hypochlorite, hydrogen peroxide or potassium hexacyanoferrate(III)-sodium hydroxide reagent. Fluorescent spots (vivid blue) were observed by irradiation with ultraviolet light (365 nm). The detection limits of Trp, 5-HT and PATs were in the range from 0.01 microg to 0.06 microg. This method was effectively applied to the detection of confiscated PAT powder and PAT in abusers' urine samples.     

Flow-injection chemiluminescence determination of enalapril maleate in pharmaceuticals and biological fluids using tris(2,2'-bipyridyl)ruthenium(II).

A chemiluminescence (CL) method using flow injection (FI) has been investigated for the rapid and sensitive determination of enalapril maleate. The method is based on the CL reaction of the drug with tris(2,2'-bipyridyl)ruthenium(II), Ru(bipy)3(2+) and acidic potassium permanganate. After selecting the best operating parameters, calibration graphs were obtained over concentration ranges of 0.005-0.2 microg/ml and 0.7-100 microg/ml with a detection limit (S/N=2) of 1.0 ng/ml. The average % found was 99.9 +/- 0.7 and 100.2 +/- 0.3 for the two concentration ranges respectively. %RSD (n=10) for 5.0 microg/ml was 0.44. The method was successfully applied to the determination of enalapril maleate in dosage forms and biological fluids without interferences.     

Chemiluminescence flow system for the determination of Fe(II) and Fe(III) in water

A novel chemiluminescence (CL) flow system has been developed for the sequential determination of Fe(II) and Fe(III) in water. Fe(II) was detected by its catalytic effect on the CL reaction between luminol immobilized on an anion exchange resin column and dissolved oxygen; Fe(III) was determined by difference measurement after on-line conversion to Fe(II) in a reducing mini-column packed with Cu plated Zn granules. For both ions, the calibration graph was linear in the range 1 × 10^–9 to 1 × 10^–6 g/mL, and the detection limit was 4 × 10^–10 g/mL. A complete analysis could be performed in 1.5 min with a relative standard deviation of less than 5%. The system could be reused for over 200 times and has been applied successfully to the determination of Fe(II) and Fe(III) in natural water samples.     

Flow-injection chemiluminescence determination of dihydralazine sulfate based on hexacyanoferrate(III) oxidation sensitized by eosin Y

A novel flow-injection chemiluminescence (CL) method for the determination of dihydralazine sulfate (DHZS) is described. The method is based on the reaction between DHZS and hexacyanoferrate(III) in alkaline solution to give weak CL signal, which is dramatically enhanced by eosin Y. The CL emission allows quantitation of DHZS concentration in the range 0.02-2.8 μg ml⁻¹ with a detection limit (3σ) of 0.012 μg ml⁻¹. The experimental conditions for the CL reaction are optimized and the possible reaction mechanism is discussed. The method has been applied to the determination of DHZS in pharmaceutical preparations and compared well with the high performance liquid chromatography (HPLC) method.     

Hexacyanoferrate(III) as a mediator in the determination of total iron in potable waters as iron(II)-1,10-phenanthroline at a single-use screen-printed carbon sensor device

Hexacyanoferrate(III) was used as a mediator in the determination of total iron, as iron(II)-1,10-phenanthroline, at a screen-printed carbon sensor device. Pre-reduction of iron(III) at −0.2 V versus Ag/AgCl (1 M KCl) in the presence of hexacyanoferrate(II) and 1,10-phenanthroline (pH 3.5-4.5), to iron(II)-1,10-phenanthroline, was complete at the unmodified carbon electrode surface. Total iron was then determined voltammetrically by oxidation of the iron(II)-1,10-phenanthroline at +0.82 V, with a detection limit of 10 μg l⁻¹.In potable waters, iron is present in hydrolysed form, and it was found necessary to change the pH to 2.5-2.7 in order to reduce the iron(III) within 30 s. A voltammetric response was not found at lower pH values owing to the non-formation of the iron(II)-1,10-phenanthroline complex below pH 2.5.Attempts to incorporate all the relevant reagents (1,10-phenanthroline, potassium hexacyanoferrate(III), potassium hydrogen sulphate, sodium acetate, and potassium chloride) into a modifying coated PVA film were partially successful. The coated electrode behaved very satisfactorily with freshly-prepared iron(II) and iron(III) solutions but with hydrolysed iron, the iron(III) signal was only 85% that of iron(II).