Preparation of polyamides derived from 1,6-diamantane dicarboxylic chloride by solution polycondensation and interfacial polycondensation

1,6-Diamantane dicarboxvlic acyl chloride ( I ) was used as a monomer with various aromatic diamines to synthesize polyamides by interfacial polycondensation and solution polycon-densation. The polyamides prepared by interfacial polycondensation had inherent viscosities between 0.38 and 0.15 dL/g. The polyamides prepared by solution polycondensation had inherent viscosities between 0.62 and 0.25 dL/g. The polyamides IIIa prepared by solution polycondensation showed the main melting transition at 380°C by dynamic mechanical analysis. In addition, it was quite temperature-stable and maintained good mechanical properties (G′?10⁸ Pa) up to high temperatures close to the main transition well above 350°C. The polyamide IIIA had a tensile strength of 35 MPa, elongations to break of 10%, and initial modulus of 0.8 GPa. Some of the polyamides were soluble in NMP, DMAc, and DMSO, depending on soft segment moiety of diamine ( II ). The polyamides prepared by interfacial polycondensation have a greater tendency to form crystal than those prepared by solution polycondensation, as evidenced by x-ray diffraction studies. These polyamides had glass transition temperatures in the 270–300°C range, and 5% weight loss temperatures up to 435°C in nitrogen. © 1995 John Wiley & Sons, Inc.     

Release rates from semi-crystalline polymer microcapsules formed by interfacial polycondensation

Microencapsulation of active agents, for their controlled release, can be brought about by the method of interfacial polycondensation [1]. In this paper, the permeabilities of the polyurea microcapsules for encapsulated cyclohexane have been determined. It is shown that the product of the permeability and membrane thickness can be changed over at least an order of magnitude by changing the degree of crystallinity of the polymer forming the membranes.     

Kinetics of polycondensation in an industrial environment

The influence of industrial reaction conditions on the kinetics of the polycondensation of polyamides is discussed. For analysis reasons the overall process was subdivided into individual kinetic phases. It will be shown that the basic features of the reaction rate in the final reaction stage can be explained assuming second order kinetics combined with a superposed reaction equilibrium. The influence of non-stoechiometry on the reaction rate is also demonstrated.     

Polyarylates (I): Investigation of the interfacial polycondensation reaction by UV

The interfacial polycondensation of bisphenol A with isophthaloyl chloride and terephthaloyl chloride in dichloromethane with triethylbenzylammonium chloride as the catalyst was described. A well-defined two-phase system had been observed, so the concentration of bisphenolate in the aqueous phase could be determined by UV spectrometer. The conversion was found to increase rapidly with reaction time, but the rate of increase in molecular weight was slow. At the initial stage with conversion up to 95%, the reaction proceeded similarly to that of solution polycon-densation because the synthesized polyarylate could be dissolved in dichloromethane, and a polymer with a low molecular weight resulted. At the final stage of the reaction, the molecular weight was increased to a very high value due to the local concentration effect. The mole ratio of bisphenol A to diacid chlorides was found to affect the molecular weight very much. In the case of a mole ratio less than 1, the reaction remained in the initial stage mostly, and the molecular weight was low. However, for a mole ratio greater than 1, polyarylate with a very high molecular weight could be obtained because the local concentration effect was much more significant owing to the high concentration of bisphenolate that remained in the aqueous phase at the final stage.     

Polyarylates. III. Kinetic studies of interfacial polycondensation

The kinetics of interfacial polycondensation of bisphenol A with isophthaloyl chloride and terephthaloyl chloride in dichloromethane with triethylbenzylammonium chloride (TEBAC) as the catalyst was investigated via measurements of bisphenolate concentration by UV. The reaction was found to be second order with respect to bisphenolate. The dependence of the rate constant on stirring speed, amount of TEBAC, and reaction temperature was studied. The rate constant was increased with an increase of stirring speed, quantity of TEBAC added, as well as the reaction temperature. The activation energy was found to be 7.7 kcal/mol at a stirring speed of 700 rpm in the presence of 0.160 of TEBAC. The role of TEBAC was found to be interesting. It did not alter the equilibrium (the partition coefficient remained the same in the presence of TEBAC), but it did enhance the transfer rate of bisphenolate.     

Thick silicate glass film by an interfacial polymerization

A silicate glass film of 2–20 µm in thickness has been formed on a fused quartz substrate by a sol-gel process using an interfacial polymerization technique. A partially hydrolyzed silicon alkoxide was dissolved in hexane and brought into contact with ammonia water in a cylindrical Teflon container. A silica gel film formed at the interface between the two immiscible liquids by the polycondensation of the partially hydrolyzed silicon alkoxide was gently placed on a substrate at the bottom of the container, by draining the liquid. The crack free gel film was dried in an ambient atmosphere and dip-coated with boron ethoxide, followed by sintering in an oven at 1250°C for 1 h. The glass film thus obtained was highly transparent and 2–20 µm in thickness depending on the concentration of the precursor solution and the pH of ammonia water.     

Studies on syntheses and properties of novel polyamides containing phosphatidylcholine analogous moieties by interfacial polycondensation

Polyamides (4a-b and 5a-b) were synthesized from interfacial polycondensation of novel diamine containing phosphatidylcholine analogous moiety, hexamethylene diamine with adipoyl chloride, or sebacoyl chloride in the interface of water and carbon tetrachloride at room temperature. The characterizations of synthesized diamine and polyamides were carried out with FT-NMR, or IR spectral method, elemental analysis, and melting point measurements, respectively. These polyamides obtained are insoluble in any normal solvents. From the results of X-ray diffraction analysis and POM observation, it was revealed that the polyamide 4b was prepared with high molecular weight, while polyamide 4a obtained seemed to have low molecular weight. For copolymers 5a and 5b, X-ray reflections from only adipoyl or sebacoyl chloride parts were observed as in crystalline state. In addition, thermal properties were also studied by DSC and transmitted light intensity measurements. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 3065–3074, 1997     

Kinetics and chemistry of the polycondensation of a-amino esters

Summary A mechanism is proposed for the polycondensation of a-amino esters in presence of carbon dioxide.     

Synthesis of ordered copolyamides by the interfacial polycondensation of the hydrolyzate of bisimidazoline with diacid chloride

Ordered copolyamides were prepared by the interfacial polycondensation of the hydrolyzate of bisimidazoline in the aqueous solution with diacid chloride in chloroform solution; bisimidazolines used were 1,4-bis(imidazoline-2-yl)butane and 1,4-bis(imidazoline-2-yl)-octane; diacid chlorides used were adipoyl chloride, sebacoyl chloride, and terephthaloyl chloride. The aqueous solutions of the hydrolyzates of bisimidazolines were prepared by heating the aqueous solutions of imidazolines at 70°C. It was shown by infrared spectra and paper electrophoresis of the hydrolyzates that bisimidazolines were hydrolyzed to give quantitatively diamines containing amides linkages of the type H₂N(CH₂)₂NH-CORCONH(CH₂)₂NH₂. The regularity in the sequence of the copolyamide of nylon 26 and nylon 2T prepared from the hydrolyzate of 1,4-bis(imidazoline-2-yl)butane and terephthaloyl chloride was studied by NMR spectrometry: it was concluded that the copolyamide was highly ordered.     

Electropolymerization : direct film formation on metal substrates-I: Kinetics and mechanism

Attempts have been made to produce, in situ, polymer films on tinplate cathodes by the electrolysis of conducting solutions of vinyl monomers for use in the can-lacquering industry. Study of a range of vinyl monomers revealed that film formation occurs at low monomer conversion only in the electrolysis of acrylonitrile and methacrylonitrile in NN'-dimethyl formamide. The highest rates of film formation were obtained by constant current electrolysis when tetraethyl ammonium p-toluene sulphonate (McKee Salt) was used as electrolyte. The rate of film formation increases with monomer concentration to a maximum and then falls rapidly. Chain propagation occurs by an anionic mechanism with ion pair formation favoured at high monomer concentrations. The physical properties of the coloured films produced rarely approach those required industrially and the method does not represent an alternative approach to the lacquering of food and beverage cans.     

Polyarylates. IV. Synthesis of block copolymers via two-step interfacial polycondensation

A new method for preparing block copolyarylates via two-step interfacial polycondensation is proposed. First, oligomers with acid chloride end groups were obtained from interfacial polycondensation with a mole ratio of bisphenol A to diacid chloride(s) less than I. In the second step, two reaction systems containing various oligomers were mixed thoroughly and more bisphenolate was charged into this mixture. The synthesis of the block copolyarylates was justified from the viewpoint of statistics, and of differences in molecular weight between oligomers and block copolymers. These block copolyarylates could be differentiated from polyarylates through crystal-line behavior and solubility in m-cresol analyses.     

On-line study of polyelectrolyte network formation by interfacial reaction

A modified synthetic boundary experiment of analytical ultracentrifugation has been employed to examine, on-line, polyelectrolyte complex formation at flat interfaces yielding highly swollen membranes/networks. Systematic experiments with sodium alginate as a polyanion and chitosan and poly(l-lysine) as polycations identified the influence of concentration, pH, molar mass, and polycation type on the membrane characteristics and the formation process. The membranes have been evaluated by five characteristics defined herein: total thickness, compactness, heterogeneity, symmetry, and growth. The results confirm the sensitivity of the method suited to elaborate general relationships for polyelectrolyte membrane design.     

Kinetics of polycondensation reactions during self-assembly of mesostructured films studied by in situ infrared spectroscopy

In situ synchrotron FTIR experiments have been performed during evaporation-induced self-assembly (EISA) of mesoporous films and the role of silica polycondensation in obtaining highly organized mesostructures has been illuminated.     

Preparation and properties of brominated poly(arylcarboxylate)s via interfacial polycondensation

The interfacial polycondensation method has been used for the preparation of brominated poly(arylcarboxylate)s. Brominated poly(arylcarboxylate)s can be prepared easily by mixing a solution of diacid chloride in a water-immiscible organic solvent with an aqueous alkaline solution of bisphenol in the presence of catalyst such as quaternary ammonium salts. First, in a dichloromethane-water system using triethylbenzylammonium chloride (TEBAC) as the catalyst a series of 2,2-bis(4-hydroxy-3,5-dibromophenyl)propane (3,3′,5,5′-tetrabromobisphenol A, TBBPA) with isophthaloyl (I) and terephthaloyl chlorides (T) has been prepared and some properties as inherent viscosity, solubility, crystallinity, and flammability have been measured. Copolymers prepared from TBBPA and mixed T/I with 33/67–67/33 molar ratios show good solubility and amorphous nature, and can be cast into transparent and tough films with limiting oxygen index of 58–59 (ANSI/ASTM D2683-77). Second, the effects of some variables as the nature of organic phase and catalysts, concentration of reactants, and basicity of aqueous phase on the interfacial polycondensation of TBBPA with equal parts of T and I [T/I (50/50)] was investigated in some detail. Among the solvents tested dichloromethane was found to be the best solvent and quaternary ammonium salts such as TEBAC and tetra-n-butylammonium bromide (TBAB) were highly efficient catalysts. Poly(arylcarboxylate)s with the highest molecular weights were obtained at an acid chloride concentration of 0.2 mol/L in dichloromethane and a concentration of TBBPA of 0.1 mol/L in alkali when TEBAC was used as catalyst. A maximum of inherent viscosity was obtained at two equivalent amounts of alkali corresponding to bisphenol. Polycondensation of several combinations of T/I (50/50) with some other tetrabromobisphenols, such as 3,3′,5,5′-tetrabromo-4,4′-biphenol, 3,3′,5,5′-tetrabromobisphenol S, 3,3′,5,5′-tetrabromo-4,4′-thiodiphenol, and 3,3′,5,5′-tetrabromophenolphthalein, were carried out with limited success. Whereas, a more favorable result could be obtained by the mixed copolycondensation of these tetrabromobisphenols and bisphenol A (BPA) with T/I (50/50). Finally, the copoly(arylcarboxylate)s from TBBPA, BPA, T, and I were prepared and characterized. The incorporation of bromine on the polymer backbone caused a decrease of inherent viscosity, glass transition temperature, crystallinity, and thermal stability of copolyarylates, whereas it caused a great enhancement of flame retardancy.     

Hydrolytic polycondensation of vinyltrimethoxysilane and formation of vinylpolysiloxane films

Hydrolytic polycondensation of vinyltrimethoxysilane (VTM) was investigated in detail to prepare vinylpolysiloxanes (VPS) having spinnability and tough gel films. VTM was hydrolyzed in various molar ratios r₁ (H₂O/VTM) = 0.5–1.6 (HCl/VTM = 0.105, EtOH/VTM = 1.44) at 70°C under a N₂ stream with stirring at 150 rpm to give vinylpolysiloxanes with =510–2100 ( =1.1–10.4). The controlled hydrolysis in r₁ = 1.40–1.64 formed VPSs having the various degrees of spinnability at N₂ flow rates of 100–500 ml/min. Transparent films of thickness 0.1–0.05 mm and tensile strength 5–16 MPa were prepared when a 20 wt% acetonemethanol (1:1, V/V) solution of VPS (r₁=1.64) was cast at 80°C for several ten days. The reaction was followed by ²⁹Si-NMR spectroscopy to investigate the distribution of unit structures T¹, T² and T³ in VPS depending on r₁.     

Reorganization of lipid nanocapsules at air-water interface. I. Kinetics of surface film formation

The size, the electrical properties and the behaviour at air-water interface of lipid nanocapsules (LNC) with various compositions were investigated. Two populations of LNC are presented in the suspension after the preparation: with (LNC II) and without (LNC I) phospholipid molecules. After the spreading at air-water interface, a rapid disaggregation of LNC I, located in the vicinity of interface, occurs leading to formation of surface film. The phospholipid molecules stabilize the structure of nanocapsules and LNC II are more stable at the interface in comparison with LNC I. The formation of a surface film was followed after by measuring the evolution of the surface pressure, relative surface area change and surface potential. A kinetic approach describing the various processes during the surface film formation was proposed. The corresponding kinetic constants were estimated.